Amico AHM Installation And Adjustment Instructions

Amico
Brand
Amico
Model
AHM
Category
Wall & ceiling mounts accessories
Type
Installation And Adjustment Instructions
AHM MONITOR ARM
1 Monitor Mounting Adapter
VESA LCD mount shown, other options available
2 Monitor Head - Rotation
Monitor Rotation Adjustment
3 Monitor Locking Lever
Locks the arm at a desired height
4 Counter Balance
Used to adjust for zero movement
5 Extension Arm *
6” extension arm shown
6 Mounting Adapter
MON adapter shown for MRS rail
7 Monitor Head - Tilt
Tilt Adjustment Handle
8 Cable Management
Manages the cables for better organization
Quick Setup
Adjustable Height Monitor (AHM) Arm
Installation and Adjustment Instructions
Installation Tools & Reference
Medical Facility Responsibility
2. Installation to Monitor
It is the responsibility of the end user to ensure all aspects of the installation are covered by following the full manual at:
http://www.amico.com/pdf/accessories/AHM_Manual.pdf
1. Installation to Structure
Amico Accessories | www.amico.com
85 Fulton Way, Richmond Hill
Ontario, L4B 2N4, Canada
4 x 1/4-20 Set screws
Use 1/8” (3mm) hex key
to tighten
Hex key (1/8”, 3/16”, M3, M4) - 1
Philips screw driver
Socket wrench (12mm, 1/2”) - 1
Adjustable wrench
**
** Not provided by Amico
* LCD mount shown, for other monitor styles, refer to manual.
*
Insert screws through M4 holes
into back of monitor (4x)
* If requested
AHM MONITOR ARM
1. Monitor Mounting Adapter (Pg. 12-18)
VESA LCD mount shown, other options available
2. Monitor Head - Rotation (Pg. 22)
Monitor Rotation Adjustment
3. Height Locking Lever (Pg. 25)
Locks the arm at a desired height
4. Counter Balance (Pg. 27)
Used to adjust for zero movement.
5. Extension Arm (Pg. 26)
6’’ extension arm shown
6.Mounting Adapter (Pg. 6-10)
MON adapter shown for MRS rail
7. Monitor Head - Tilt (Pg. 21)
Tilt Adjustment Handle
8. Cable Management (Pg. 29)
Manages the cables of the Monitor
for better organization.
2
3
4
5
6
1
7
8
*WARNING: Never attempt to mount or remove the arm from the rail when a monitor is installed.
7
*WARNING: Support AHM arm until the set screws are tightened, AHM arm can slide down when
set screws are not tightened.
Toll Free Tel: 1.877.264.2697 l Tel: 905.763.7778
Fax: 905.763.8587
Installation and Adjustment Instructions
A. Rotation (AHM Side to Side) B. Head Tilt
C. Rotation (Monitor Head Side to Side)
D. Height Locking Lever Adjustments
Insert Height Locking Lever
E. Counter Balance
Amico Accessories | www.amico.com
85 Fulton Way, Richmond Hill
Ontario, L4B 2N4, Canada
F. Cable Management
Quick Adjustment Reference
Adjustable Height Monitor (AHM) Arm
Rotate Mid Point
Rotate End Point
To adjust arm height, always be sure to loosen the height locking lever rst.
Loosing or tightening this bolt will
adjust the resistance of the arm.
When properly counterbalanced, arm should
remain in neutral position when unlocked.
Counter Balance Bolt (1/2”)
Opening to the cover
Height Locking Lever
Cable Guide
Bottom of the
AHM Arm
Cable Cover
Cable Guide
Counter Balance Bolt (1/2”)
Height Locking Lever:
Rotate Counter-Clockwise
to Release
Rotate Clockwise to Lock
To rotate at rst arm
To rotate at second arm
Hex
*
* If applicable
Toll Free Tel: 1.877.264.2697 l Tel: 905.763.7778
Fax: 905.763.8587
Bottom Side of the AHM Arm
Grooves
Insert cables into cable guide, then squeeze cable guide and press onto the bottom of the AHM.
Bottom Side of Cable Cover
  • Page 1 1
  • Page 2 2

Amico AHM Installation And Adjustment Instructions

Amico
Brand
Amico
Model
AHM
Category
Wall & ceiling mounts accessories
Type
Installation And Adjustment Instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents