Chamberlain MyQ 888LM Installation guide

Brand: Chamberlain

Model: MyQ 888LM

Category: Garage Door Opener

Type: Installation guide

MyQ

CONTROL PANEL

MODEL 888LM

To prevent possible SERIOUS INJURY or DEATH from electrocution:

• Be sure power is NOT connected BEFORE installing door control.

• Connect ONLY to 7-28 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing

garage door:

• Install door control within sight of garage door, out of reach of

children at a minimum height of 5 feet (1.5 m), and away from ALL

moving parts of door.

• NEVER permit children to operate or play with door control push

buttons or remote control transmitters.

• Activate door ONLY when it can be seen clearly, is properly

adjusted, and there are no obstructions to door travel.

• ALWAYS keep garage door in sight until completely closed. NEVER

permit anyone to cross path of closing garage door.

• DO NOT install this door control on garage door opener systems

controlling one-piece or swing doors.

To provide an adequate visual alert, the garage door opener light

bulb(s) MUST be a minimum of 40 Watt (or equivalent).

The MyQ

Control Panel is intended to be installed with Security✚™

Garage Door Openers manufactured between 1998 and present. The

MyQ

Control Panel is NOT compatible with Security✚ 2.0™ Garage Door

Openers. DO NOT install this door control on garage door opener

systems controlling one-piece or swing doors.

APPLICATION

The MyQ

Control Panel offers a quick and convenient way to add

Security✚ 2.0™ and MyQ

technology to your existing garage door

opener. MyQ

technology uses a 900MHz signal to provide two-way

communication between the garage door opener and MyQ

enabled

accessories. When programmed to the Liftmaster

Internet Gateway you

can monitor and control your garage door from any internet enabled

computer or smartphone. You may program up to 12 Security✚ 2.0™

remote controls, 2 Security✚ 2.0™ keyless entries and a combination of

16 MyQ

accessories to the MyQ

control panel.

COMPATIBLE ACCESSORIES

Security

✚

2.0™ Accessories: MyQ

Accessories:

Model 891LM

1- Button Remote Control

Model 823LM

Remote Light Switch

Model 893LM

3-Button Remote Control

Model 825LM

Remote Light Control

Model 890MAX

3-Button Mini MAX Remote Control

Model 828LM

LiftMaster

Internet Gateway

Model 893MAX

3-Button MAX Remote Control

Model 829LM

Garage Door and Gate Monitor

Model 895MAX

3-Button Premium MAX Remote

Control

Model 877LM

Wireless Keyless Entry

Model 877MAX

Wireless MAX Keyless Entry

OVERVIEW

Install the MyQ

Control Panel in place of the existing door control. Due

to power consumption the MyQ

Control Panel cannot be used in

conjunction with another wired door control connected to your garage

door opener. If an additional door control is needed, the wireless door

control model 885LM can be programmed to the MyQ

Control Panel.

To program the 885LM to the MyQ

Control Panel, follow the remote

control programming steps. When in battery back-up mode, any feature

using unattended operation such as Timer-to-Close, closure from a

garage door and gate monitor or remote operation utilizing the

LiftMaster

Internet Gateway will be disabled.

1. Disconnect all electrical and battery power (if applicable) to the

garage door opener.

2. Remove the existing door control from the wall.

3. Note the polarity of the wires connected to the existing door

control.

• Label the wire connected to the RED terminal.

• Label the wire connected to the WHITE terminal.

Disconnect the wires from the existing door control.

INSTALLATION

Existing Door Control

Discard, donate

or recycle

Wire from

RED terminal

Connect

RED wire to

R terminal

Wire from

WHITE

terminal

Connect

WHITE

wire to W

terminal

MyQ

Control Panel

4. Connect the wires to the new MyQ

Control Panel. Make sure the

polarity is correct.

• Red wire to the R terminal.

• White wire to the W terminal.

5. Mount the MyQ

Control Panel to the wall.

6. Reconnect power. The yellow command LED and the red learn LED

will blink quickly for up to 5 minutes as the control panel

recharges. When the control panel is operational, the yellow

command LED will glow steadily.

7. To test the control panel, press the push bar to activate the garage

door opener.

For more information, please visit www.devancocanada.com or call toll free at 855-931-3334

?? ??

PROGRAMMING

REMOTE CONTROL

1. Press the MyQ

Control Panel LEARN

button twice, the red learn LED will turn

on.

2. Press the button on the remote control

that you wish to operate your garage

door.

3. The garage door opener lights will flash

(or two clicks will be heard) when the

code has been programmed.

1. Press the MyQ

Control Panel LEARN button twice, the red learn

LED will turn on.

2. Enter a 4-digit personal identification number (PIN) of your choice

on the keyless entry keypad. Then press the ENTER button.

3. The garage door opener lights will flash (or two clicks will be heard)

when the code has been programmed.

KEYLESS ENTRY

LEARN

Button

LEARN

Button

Model 825LM - Remote Light Control

Light module can be synchronized with the

garage door opener light bulbs.

Model 823LM - Remote Light Switch

Light module can be synchronized with

the garage door opener light bulbs.

LEARN

Button

Model 829LM - Garage Door and Gate Monitor

Indicates the status of your garage door from inside

the home and allows you to close an open garage door

from inside the house.

MyQ

ENABLED

ACCESSORIES

1. Press the MyQ

Control Panel LEARN

button twice, the red learn LED will

turn on.

2. Press the LEARN button on the MyQ

device.*

* MyQ

accessories may be programmed to the

LiftMaster

Internet Gateway (Model 828LM)

or the MyQ

control panel. For instructions on

programming to the internet gateway refer to

the manual.

INTERNET GATEWAY

The LiftMaster

Internet Gateway gives you control of your garage door

from your internet connected computer or mobile device. You must have

your internet gateway registered to your customer account at

www.myliftmaster.com in order to use it with the MyQ

Control Panel. Go

to www.myliftmaster.com and follow the instructions to create an account

and register your device if you have not already.

To program your control panel to the LiftMaster

Internet Gateway:

1. Go to www.myliftmaster.com from a computer or mobile device.

2. Click on “Manage Places>Add New Device>Garage Door Opener”

and follow the directions.

3. Once you click ADD you have 3 minutes to press the LEARN button

two times on the MyQ

control panel. The red learn LED will turn

on.

4. The red learn LED will turn off when programming is complete.

Once the control panel is learned, it will appear on your screen. You

can then name the device (e.g., My Control Panel, etc.).

Model 828LM

LiftMaster

Internet Gateway

www.myliftmaster.com

Command

LED (yellow)

Learn

LED

(Red)

PUSH BAR

Press the push bar to open/close the door.

LIGHTS

Press the LIGHT button to turn the garage door opener lights on or off.

When the lights are turned on they will stay on until the LIGHT button is

pressed again, or until the garage door opener is activated. Once the

garage door opener is activated the lights will turn off after the specified

period of time (the factory setting is 4-1/2 minutes). The LIGHT button

will not control the lights when the door is in motion.

To change the amount of time the garage door opener lights will stay on:

Press and hold the LOCK button until the garage door opener lights flash.

The time interval is indicated by the number of flashes.

Light Feature

The lights will turn on when someone enters through the open garage

door and the safety reversing sensor infrared beam is broken.

Activate:

Start with the garage door opener lights on. Press and hold the LIGHT

button until the garage door opener lights turn off, then on again.*

Deactivate:

Press and hold the LIGHT button until the garage door opener lights

turn on, then off again.*

* Approximately 10 seconds

FUNCTIONS

NUMBER OF TIMES GARAGE

DOOR OPENER LIGHTS FLASH

1234

TIME THE GARAGE DOOR

OPENER LIGHT STAYS ON

1 ½

Minutes

2 ½

Minutes

3 ½

Minutes

4 ½

Minutes

MOTION SENSOR

This feature will automatically turn on the garage door opener lights when

motion is sensed. The lights will come on for the set period of time, then

shut off.

Activate/Deactivate:

Slide the motion sensor switch ON or OFF.

TIMER-TO-CLOSE (TTC)

NOTE: DO NOT install this door control on garage door opener systems

controlling one-piece or swing doors.

The TTC feature automatically closes the door after a specified time

period (1, 5, or 10 minutes). Once the TTC has been set and the door is

open, the LED for the selected close interval will blink and begin to count

down to close the door. The control panel will beep and the garage door

opener lights will flash before closing the door.

The TTC feature will deactivate if the garage door encounters an

obstruction twice; or the safety reversing sensors are incorrectly installed.

The garage door will reverse open and WILL NOT close until the

obstructions are clear or the safety reversing sensors are correctly

installed. When the obstruction has been cleared or the safety reversing

sensors have been aligned, the door will close when the garage door

opener is activated.

Activate:

Press and hold the ON button until one of the TTC LEDs light up. Then

press the ON button again to cycle through the time interval options

(the corresponding TTC LED will light for each time interval). The

garage door opener light bulbs will blink as confirmation.

Deactivate:

Press and hold the OFF button until all TTC LEDs turn off and a beep is

heard from the control panel.

Temporarily hold door open (suspend TTC):

Press and release the HOLD OPEN button. The HOLD OPEN button will

begin to flash. Press the HOLD OPEN button again to resume normal

TTC operation.

LOCK

Activate*:

Press and hold the LOCK button for 2 seconds. The command LED will

flash as long as the lock feature is activated and your handheld remote

control will not operate your door at this time.

Deactivate:

Press and hold the LOCK button again for 2 seconds. The command

LED will stop flashing and normal operation will resume.

* Your LiftMaster

keypad will continue to work when the LOCK has been

activated.

LIGHT

Button

1 Minute

TTC LED

5 Minute

TTC LED

10 Minute

TTC LED

ON Button

Command

LED (yellow)

OFF Button

HOLD OPEN

Button

Motion

Sensor

LEARN

button

Learn LED

(Red)

LOCK

button

Push Bar

FOR SERVICE DIAL OUR TOLL FREE NUMBER:

1-800-528-9131

www.liftmaster.com

ONE YEAR LIMITED WARRANTY

The Chamberlain Group, Inc. warrants to the first consumer purchaser of

this product that is free from defect in materials and/or workmanship for

a period of 1 year from the date of purchase.

• If the yellow command LED does not turn on, reverse the wires

connected to the R and W terminals of the control panel. Replace

wire if necessary.

• If yellow and red LEDs are blinking slowly, the control panel is not

compatible with your garage door opener.

• If the yellow and red LEDs are blinking quickly, the control panel is

charging, and may take up to 5 minutes to become operational.

NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or modiﬁ cations of this transceiver

are prohibited. THERE ARE NO USER SERVICEABLE PARTS. Any changes or modiﬁ cations not expressly

approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

This Class B digital apparatus complies with Canadian ICES-003.

AVIS: Les règles de la FCC et/ou d’Industrie Canada (IC) interdisent tout ajustement ou toute modiﬁ cation de

ce récepteur. IL N’EXISTE AUCUNE PIÈCE SUSCEPTIBLE D’ÊTRE ENTRETENUE PAR L’UTILISATEUR. Tout

changement ou toute modiﬁ cation non expressément approuvé par la partie responsable de la conformité peut

avoir pour résultat d'annuler l'autorité de l'utilisateur de faire fonctionner l'équipement.

Cet appareil est conforme aux dispositions de la partie 15 du règlement de la FCC et de l'norme IC RSS-210.

Son utilisation est assujettie aux deux conditoins suivantes: (1) ce dispositif ne peut causer des interférences

nuisibles, et (2) ce dispositif doit accepter toute interférence recue, y compris une interférence pouvant causer

un fonctionnement non souhaité.

Cet appareil numerique de la classe B est conforme a la norme NMB-003 du Canada.

WARRANTY

TROUBLESHOOTING

ERASE DEVICES FROM MEMORY

Erase all remote controls and keyless entries:

1. Press and hold the LEARN button on the control panel until the red

learn LED goes out (approximately 6 seconds). All remote control

and keyless entry codes are now erased. Reprogram any

compatible accessory you wish to use.

NOTE: Erasing remote controls and keyless entries from the control panel

does not erase them from the garage door opener, you need to erase the

memory of the garage door opener separately.

Erase all devices (including MyQ

enabled accessories):

1. Press and hold the LEARN button on the control panel until the red

learn LED goes out (approximately 6 seconds).

2. Immediately press and hold the LEARN button again until the red

learn LED goes out. All codes are now erased. Reprogram any