3-280-870-11(1)
2008 Sony Corporation
Digital Video Camera Recorder
Operating Guide
DCR-SR35E/SR36E/SR45E/SR46E/SR55E/
SR65E/SR75E/SR85E
For details on the advanced operations, please refer to
“Handycam Handbook” (PDF).
2
Read this rst
Before operating the unit, please read this
manual thoroughly, and retain it for future
reference.
WARNING
To reduce re or shock hazard, do not
expose the unit to rain or moisture.
Do not expose the batteries to
excessive heat such as sunshine, re or
the like.
CAUTION
Replace the battery with the specied
type only. Otherwise, re or injury may
result.
Notice for customers in the United
Kingdom
A moulded plug complying with BS1363 is
tted to this equipment for your safety and
convenience.
Should the fuse in the plug supplied need to
be replaced, a fuse of the same rating as the
supplied one and approved by ASTA or BSI
to BS1362 (i.e., marked with or mark)
must be used. If the plug supplied with this
equipment has a detachable fuse cover,
be sure to attach the fuse cover aer you
change the fuse. Never use the plug without
the fuse cover.
If you should lose the fuse cover, please
contact your nearest Sony service station.
FOR CUSTOMERS IN EUROPE
ATTENTION
e electromagnetic elds at the specic
frequencies may inuence the picture and sound
of this unit.
is product has been tested and found
compliant with the limits set out in the EMC
Directive for using connection cables shorter than
3 meters (9.8 feet).
Notice
If static electricity or electromagnetism causes
data transfer to discontinue midway (fail), restart
the application or disconnect and connect the
USB cable again.
Disposal of Old Electrical &
Electronic Equipment (Applicable
in the European Union and
other European countries with
separate collection systems)
is symbol on the product or on its
packaging indicates that this product shall
not be treated as household waste. Instead
it shall be handed over to the applicable
collection point for the recycling of
electrical and electronic equipment.
By ensuring this product is disposed of
correctly, you will help prevent potential
negative consequences for the environment
and human health, which could otherwise
be caused by inappropriate waste handling
of this product. e recycling of materials
will help to conserve natural resources.
For more detailed information about
recycling of this product, please contact
your local Civic Oce, your household
waste disposal service or the shop where
you purchased the product.
Applicable Accessories: Remote
Commander (DCR-SR55E/SR65E/SR75E/
SR85E)
Disposal of waste batteries
(applicable in the European
Union and other European
countries with separate
collection systems)
is symbol on the battery or on the
packaging indicates that the battery
provided with this product shall not be
treated as household waste.
By ensuring these batteries are disposed of
correctly, you will help prevent potentially
3
negative consequences for the environment
and human health which could otherwise
be caused by inappropriate waste handling
of the battery. e recycling of the
materials will help to conserve natural
resources.
In case of products that for safety,
performance or data integrity reasons
require a permanent connection with an
incorporated battery, this battery should be
replaced by qualied service sta only.
To ensure that the battery will be treated
properly, hand over the product at end-of-
life to the applicable collection point for
the recycling of electrical and electronic
equipment.
For all other batteries, please view the
section on how to remove the battery from
the product safely. Hand the battery over
to the applicable collection point for the
recycling of waste batteries.
For more detailed information about
recycling of this product or battery, please
contact your local Civic Oce, your
household waste disposal service or the
shop where you purchased the product.
Notice for the customers in the
countries applying EU Directives
e manufacturer of this product is Sony
Corporation, 1-7-1 Konan Minato-ku
Tokyo, 108-0075 Japan. e Authorized
Representative for EMC and product safety
is Sony Deutschland GmbH, Hedelnger
Strasse 61, 70327 Stuttgart, Germany. For
any service or guarantee matters please
refer to the addresses given in separate
service or guarantee documents.
For customers in the U.S.A.
If you have any questions about this
product, you may call:
Sony Customer Information Center 1-800-
222-SONY (7669).
e number below is for the FCC related
matters only.
Regulatory Information
Declaration of Conformity
Trade Name: SONY
Model No.: DCR-SR45E, DCR-SR46E
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo, San Diego,
CA 92127 U.S.A.
Telephone number: 858-942-2230
is device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) is device
may not cause harmful interference,
and (2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Declaration of Conformity
Trade Name: SONY
Model No.: DCR-SR65E, DCR-SR85E
Responsible Party: Sony Electronics Inc.
Address: 16530 Via Esprillo, San Diego,
CA 92127 U.S.A.
Telephone number: 858-942-2230
is device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) is device
may not cause harmful interference,
and (2) this device must accept any
interference received, including
interference that may cause undesired
operation.
Note
DCR-SR65E/SR85E is to be used with the
Handycam Station Model DCRA-C200 and AC
Adaptor Model AC-L200/L200B.
CAUTION
You are cautioned that any changes or
modications not expressly approved in
this manual could void your authority to
operate this equipment.
4
Note
is equipment has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules.
ese limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
is equipment generates, uses, and
can radiate radio frequency energy and,
if not installed and used in accordance
with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined
by turning the equipment o and on,
the user is encouraged to try to correct
the interference by one or more of the
following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet on
a circuit dierent from that to which the
receiver is connected.
Consult the dealer or an experienced radio/
TV technician for help.
e supplied interface cable must be used
with the equipment in order to comply
with the limits for a digital device pursuant
to Subpart B of Part 15 of FCC Rules.
Battery pack
is device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:(1) is device
may not cause harmful interference, and
(2) this device must accept any interference
received, including interference that may
cause undesired operation.
Notes on use
Supplied items
e numbers in ( ) are the supplied
quantity.
AC Adaptor (1)
Power cord (Mains lead) (1)
Handycam Station (1) (DCR-SR55E/SR65E/
SR75E/SR85E)
A/V connecting cable (1)
USB cable (1)
Wireless Remote Commander (1) (DCR-
SR55E/SR65E/SR75E/SR85E)
A button-type lithium battery is already
installed.
Rechargeable battery pack NP-FH40 (1)
21-pin adaptor (1) (DCR-SR55E/SR65E/SR75E/
SR85E)
For the models with the mark printed on
their bottom surfaces only.
CD-ROM “Handycam Application Soware”
(1) (p.
25)
Picture Motion Browser (Soware)
PMB Guide
Handycam Handbook (PDF)
“Operating Guide” (is manual) (1)
Using the camcorder
e camcorder is not dustproofed, dripproofed
or waterproofed. See “Precautions” (p. 31).
Do not do any of the following when the
(movie)/ (still image) lamps (p. 11) or
ACCESS lamps (p.
13, 18) is lit or ashing.
Otherwise the media may be damaged, recorded
images may be lost or other malfunctions could
occur.
Remove the “Memory Stick PRO Duo.”
Remove the battery pack or AC Adaptor from
the camcorder.
Apply mechanical shock or vibration to the
camcorder.
When connecting your camcorder to another
device with a cable, be sure to insert the
connector plug in the correct way. Pushing the
plug forcibly into the terminal will damage the
5
terminal and may result in a malfunction of
your camcorder.
Do not apply shock or vibration to your
camcorder. e hard disk of the camcorder may
not be recognized, or recording or playback
may not be possible.
Do not use your camcorder in very loud areas.
e hard disk of the camcorder may not be
recognized, or recording may not be possible.
To protect the internal hard disk from shock
by dropping, the camcorder has drop sensor
function*. When a drop occurs, or under a non-
gravity condition, the block noise made when
this function is activated by the camcorder may
also be recorded. If the drop sensor catches a
drop repeatedly, recording/play back may be
stopped.
When the temperature of the camcorder
becomes extremely high or extremely low, you
may not be able to record or play back on the
camcorder, due to the protection features of the
camcorder being activated in such situations.
In this case, an indicator appears on the LCD
screen (p.
29).
Do not turn on the camcorder in a low-pressure
area, where the altitude is more than 3,000
meters (9,800 feet). Doing so may damage the
hard disk drive of your camcorder.
If you repeat recording/deleting images for a
long time, fragmentation of data occurs on the
media. Images cannot be saved or recorded. In
such a case, save your images on some type of
external media rst, and then perform [MEDIA
FORMAT]*.
Fasten the grip belt and hold your camcorder
correctly while recording.
To adjust the LCD panel, open the LCD panel
90 degrees to the camcorder (), then rotate it
to the best angle to record or play ().
You can rotate the LCD panel 180 degrees to
the lens side () to record in mirror mode.
e LCD screen is manufactured using
extremely high-precision technology, so over
99.99% of the pixels are operational for eective
use. However, there may be some tiny black
points and/or bright points (white, red, blue,
or green in color) that appear constantly on the
LCD screen. ese points are normal results of
the manufacturing process and do not aect the
recording in any way.
Remove the insulation sheet before using the
Remote Commander.
(DCR-SR55E/SR65E/SR75E/SR85E)
Types of “Memory Stick” you can use
with your camcorder
For recording movies, it is recommended that
you use a “Memory Stick PRO Duo” of 512 MB
or larger marked with:
(“Memory Stick
PRO Duo”)*
(“Memory Stick
PRO-HG Duo”)
* Marked with Mark2 or not are available.
A “Memory Stick PRO Duo” of up to 8 GB has
been conrmed to operate correctly with this
camcorder.
See page 12 for the recordable time of a
“Memory Stick PRO Duo.”
“Memory Stick PRO Duo” and “Memory Stick
PRO-HG Duo” are both called as “Memory
Stick PRO Duo” in this manual.
Insulation sheet
90 degrees to the
camcorder
90 degrees (max.)
180 degrees (max.)
6
On recording
Before starting to record, test the recording
function to make sure the image and sound are
recorded without any problems.
Compensation for failure or loss of recording
cannot be provided, even if recording or
playback is not possible due to a malfunction of
the camcorder, recording media, etc.
TV color systems dier depending on the
country/region. To view your recordings on a
TV, you need a PAL system-based TV.
Television programs, lms, video tapes,
and other materials may be copyrighted.
Unauthorized recording of such materials may
be contrary to the copyright laws.
Save all your recorded image data
To prevent your image data from being lost,
save all your recorded images on external media
periodically. It is recommended that you save
the image data on a disc such as a DVD-R using
your computer*. Also, you can save your image
data using a VCR, or a DVD/HDD recorder*.
When the camcorder is connected to a
computer
Do not try to format the hard disk of the
camcorder using a computer. If you do so, your
camcorder may not operate correctly.
Note on disposal/transfer
If you perform [MEDIA FORMAT]* to format
the hard disk of the camcorder, data may not be
completely deleted from the hard disk. When
you transfer the camcorder, it is recommended
that you perform [ EMPTY]* to prevent the
recovery of your data.
In addition to the above, when you dispose of
the camcorder, it is recommended that you
destroy the actual body of the camcorder.
About language setting
e on-screen displays in each local language
are used for illustrating the operating
procedures. Change the screen language before
using your camcorder if necessary (p.
11).
About this manual
e LCD screens and indicators shown in this
manual were taken with a digital still camera,
and may look dierent from what you actually
see.
In this Operating Guide, the hard disk and
“Memory Stick PRO Duo” are called “media.”
Unless otherwise specically indicated,
illustrations in this manual are based on DCR-
SR85E.
e screenshots are from Windows Vista, and
may vary depending on the operating system of
the computer.
* Refer also to “Handycam Handbook” (PDF)
and “PMB Guide.”
7
Table of contents
Read this rst .................................................2
Getting Started
Step 1: Charging the battery pack .........8
Step 2: Turning the power on, and
setting the date and time .................... 11
Changing the language setting ............... 11
Step 3: Selecting the media ................... 12
Recording/Playback
Recording ..................................................... 14
Playback ........................................................ 15
Playing the image on a TV ........................... 16
Other parts and functions of the
camcorder ................................................. 17
Indicators displayed during recording/
playback ..................................................... 19
Performing various functions -
“ HOME” and “ OPTION” .............. 21
Saving images ............................................ 23
Deleting images ......................................... 24
Enjoying with a computer
Performing with a computer ................. 25
Handbook/software to be installed ....... 25
Installing “Picture Motion Browser” ........ 25
Troubleshooting
Troubleshooting ........................................ 28
Self-diagnosis display/Warning
indicators ............................................................ 29
Additional Information
Precautions .................................................. 31
Specications .............................................. 33
8
Getting Started
Step 1: Charging the battery pack
DCR-SR55E/SR65E/SR75E/SR85E
4
DCR-SR35E/SR36E/SR45E/SR46E
You can charge the “InfoLITHIUM”
battery pack (H series) after attaching
it to your camcorder.
Notes
Your camcorder operates only with an
“InfoLITHIUM” battery pack (H series).
1 Turn the POWER switch in the
direction of the arrow to OFF (CHG)
(the default setting).
2 Attach the battery pack by sliding it
in the direction of the arrow until it
clicks.
3 For DCR-SR55E/SR65E/SR75E/
SR85E:
Connect the AC Adaptor to the DC
IN jack on the Handycam Station.
For DCR-SR35E/SR36E/SR45E/
SR46E:
Connect the AC Adaptor to the DC
IN jack on your camcorder.
Open the jack cover and connect the
DC plug of the AC Adaptor to the DC
IN jack.
4 For DCR-SR55E/SR65E/SR75E/
SR85E:
Connect the power cord (mains
lead) to the AC Adaptor and the
wall outlet (wall socket). Insert
the camcorder into the Handycam
Station securely, all the way to the
bottom.
When setting the camcorder onto the
Handycam Station, close the DC IN jack
cover.
Battery pack
DC IN jack
DC plug
With the mark
on the top
AC Adaptor
Power cord
(Mains lead)
To the wall outlet
(wall socket)
CHG lamp
POWER switch
DC IN jack
DC plug
With the mark on the right
Power cord
(Mains lead)
AC Adaptor
To the wall outlet
(wall socket)
Open the jack cover.
Getting Started
9
For DCR-SR35E/SR36E/SR45E/
SR46E:
Connect the power cord (mains
lead) to the AC Adaptor and the wall
outlet (wall socket).
e CHG (charge) lamp lights up and
charging starts.
e CHG (charge) lamp turns o when
the battery is fully charged.
Disconnect the AC Adaptor from the
DC IN jack holding both the DC plug
and the Handycam Station (DCR-
SR55E/SR65E/SR75E/SR85E) or your
camcorder (DCR-SR35E/SR36E/SR45E/
SR46E).
Tips
For DCR-SR55E/SR65E/SR75E/SR85E:
Same as DCR-SR35E/SR36E/SR45E/SR46E, you
can charge the battery pack by connecting the
AC Adaptor to your camcorder.
To remove the battery pack
Turn the POWER switch to OFF (CHG).
Slide the BATT (battery) release lever and
remove the battery pack.
Available running time for the
supplied battery pack
Charging time:
Approximate time (min.) required to fully
charge a completely exhausted battery
pack.
Recording/Playback time:
Approximate time (min.) available when
you use a fully charged battery pack.
(Unit:min.)
DCR-SR35E/SR36E/
SR45E/SR46E
DCR-SR55E/SR65E/
SR75E/SR85E
Charging time 125 125
Recording time
Continuous
recording
time
100
110
90
105
Typical
recording
time
50
50
45
50
Playback time
120
140
120
140
Top: When the media is set to the hard disk
Bottom: When the media is set to the “Memory
Stick PRO Duo”
Notes
All times measured under the following
settings:
Recording mode: [SP]
e LCD backlight turns: [ON]
Typical recording time shows the time when
you repeat recording start/stop, turning the
power on/o and zooming.
On the battery pack
Before changing the battery pack or removing
the AC Adaptor from the camcorder, turn
the POWER switch to OFF (CHG) and make
sure that the (Movie) lamp/ (Still) lamp
(p.
11)/ACCESS lamps (p. 13, 18) is turned o.
e power will not be supplied from the
battery as long as the AC Adaptor is connected
to the DC IN jack of your camcorder or the
Handycam Station (DCR-SR55E/SR65E/SR75E/
SR85E), even when the power cord (mains
lead) is disconnected from the wall outlet (wall
socket).
On the charging/recording/playback time
Times measured when using the camcorder at
25°C (77 ˚F) (10°C to 30°C (50 ˚F to 86 ˚F) is
recommended).
e available recording and playback time will
be shorter when you use your camcorder in low
temperatures.
BATT (battery)
release lever
10
e available recording and playback time will
be shorter depending on the conditions under
which you use your camcorder.
On the AC Adaptor
Use the nearby wall outlet (wall socket) when
using the AC Adaptor. Disconnect the AC
Adaptor from the wall outlet (wall socket)
immediately if any malfunction occurs while
using your camcorder.
Do not use the AC Adaptor placed in a narrow
space, such as between a wall and furniture.
Do not short-circuit the DC plug of the AC
Adaptor or battery terminal with any metallic
objects. is may cause a malfunction.
Even if your camcorder is turned o, AC power
source (mains) is still supplied to it while
connected to the wall outlet (wall socket) via the
AC Adaptor.
Getting Started
11
Step 2: Turning the power on, and setting the date and
time
1 While pressing the green button,
turn the POWER switch repeatedly
in the direction of the arrow until
the respective lamp lights up.
(Movie): To record movies
(Still): To record still images
Go to step 3 when you turn on your
camcorder for the rst time.
When you turn on the (Still) lamp,
the screen aspect ratio is changed to 4:3
automatically.
2 Touch (HOME) (SETTINGS)
[CLOCK/ LANG] [CLOCK
SET].
e [CLOCK SET] screen appears.
3 Select the desired geographical
area with / , then touch [NEXT].
4 Set [SUMMERTIME], [Y] (year), [M]
(month), [D] (day), hour and minute,
then touch .
e clock starts.
Tips
e date and time do not appear during
recording, but they are automatically recorded
on the media, and can be displayed during
playback.
You can turn o the operation beeps by
touching (HOME) (SETTINGS)
[SOUND/DISP SET] [BEEP] [OFF].
Changing the language setting
You can change the on-screen displays to
show messages in a specied language.
Touch (HOME) (SETTINGS)
[CLOCK/ LANG] [ LANGUAGE
SET], then select the desired language.
Touch the button on the
LCD screen.
When using the
camcorder for the first
time, the [CLOCK
SET] screen appears
on the LCD screen.
POWER switch
(HOME) (p. 21)
12
Step 3: Selecting the media
You can select the hard disk or “Memory
Stick PRO Duo” as the recording/playback/
editing media on your camcorder. Select
the media for movies and still images
separately.
e default setting is hard disk for movies
and still images.
Notes
You can do recording/playback/editing
operations for the selected media only. When
you want to change, reselect the media.
e recordable time with [SP] recording mode
(the default setting) is as follows (approx):
e internal hard disk:
DCR-SR35E/SR45E: 10 hours 40 minutes
DCR-SR36E/SR46E/SR55E/SR65E: 14 hours
30 minutes
DCR-SR75E/SR85E: 21 hours 50 minutes
“Memory Stick PRO Duo” (4 GB) made by
Sony Corporation: 80 minutes
Check the number of recordable still images on
the LCD screen of your camcorder (p.
19).
1 Touch (HOME) (MANAGE
MEDIA) tab on the screen.
2 Touch [MOVIE MEDIA SET] to select
the media for movies, and touch
[PHOTO MEDIA SET] to select the
media for still images.
e media setting screen appears.
60min
3 Select the media you want to set.
4 Touch [YES] .
e media is changed.
To conrm the recording media setting
Turn the POWER switch repeatedly to light
up the (Movie)/ (Still) lamp, depending
on which media setting you want to check.
Check the media icon on the screen.
Inserting the “Memory Stick PRO Duo”
Prepare a “Memory Stick PRO Duo” if
[MEMORY STICK] has been selected as
the media.
For types of “Memory Stick” you can use in
your camcorder, see page 5.
1 Insert a “Memory Stick PRO Duo.”
Open the Memory Stick Duo cover in the
direction of the arrow.
Insert a “Memory Stick PRO Duo” into
the Memory Stick Duo slot in the right
orientation until it clicks.
Close the Memory Stick Duo cover.
: Hard disk
: “Memory
Stick PRO Duo”
Movie
Hard disk
“Memory Stick”
Still image
Getting Started
13
2 If you have selected [MEMORY
STICK] as the movie media, turn the
POWER switch until the (Movie)
lamp lights up.
e [Create a new Image Database File.]
screen appears on the LCD screen when
you insert a new “Memory Stick PRO
Duo.”
3 Touch [YES].
To record only still images on a
“Memory Stick PRO Duo,” touch [NO].
To remove the “Memory Stick PRO
Duo”
Open the Memory Stick Duo cover and
lightly push on the “Memory Stick PRO
Duo.”
Notes
Do not open the Memory Stick Duo cover while
recording.
Inserting a “Memory Stick PRO Duo” forcibly
in the wrong direction may cause a malfunction
to the “Memory Stick PRO Duo,” Memory Stick
Duo slot or image data.
If [Failed to create a new Image Database File.
It may be possible that there is not enough free
space.] appears in step 3, format the “Memory
Stick PRO Duo.” All recorded data on the
“Memory Stick PRO Duo” will be deleted when
you format.
Be careful not to allow the “Memory Stick PRO
Duo” to pop out and fall when you push on and
remove it.
ACCESS lamp
(“Memory Stick
PRO Duo”)
14
Recording/Playback
Recording
e images are recorded on the media selected on the media setting (p. 12).
e default setting is hard disk for both movies and still images.
1 Slide the LENS COVER switch to open.
2 Turn the POWER switch until the respective lamp lights up.
Press the green button only when the POWER switch is in the OFF (CHG) position.
3 Start recording.
Movies
Press START/STOP (or ).
To stop recording, press START/STOP
again.
Still Images
Press PHOTO lightly to adjust the focus
(a beep sounds), then press it fully
(a shutter click sounds).
appears beside or . When
disappears, the image has been recorded.
Tips
You can check the free media space by touching
(HOME) (MANAGE MEDIA)
[MEDIA INFO].
e maximum continuous recordable time of
movies is approximately 13 hours.
When a movie le exceeds 2 GB, the next movie
le is created automatically.
LENS COVER switch
POWER switch
START/STOP
START/STOP
[STBY] [REC]
PHOTO
Flashing Lights up
: To record movies
: To record still images
Recording/Playback
15
Playback
You can play back images recorded on the media selected in the media setting (p. 12).
e default setting is the hard disk.
1 Turn the POWER switch to turn on your camcorder.
2 Press the (VIEW IMAGES) (or ) button.
e VISUAL INDEX screen appears on the LCD screen. (It may take some seconds.)
3 Start playback.
Movies
Touch the tab, and the movie to be
played back.
Still Images
Touch the tab, and the still image to
be played back.
(VIEW IMAGES) button
POWER switch
(VIEW IMAGES)
button
HOME MENU
Previous 6 images
Next 6 images
Returns to the recording screen
Displays movies
Displays still images
(OPTION)
Searches for images by date
Goes to the (Face Index) screen
Goes to the (Film Roll Index) screen
Slide show button
Goes to the VISUAL
INDEX screen
Previous/
Next
Goes to beginning
of the scene/
previous movie
Toggles Play
or Pause as
you touch
Next
movie
Stop (goes to the VISUAL
INDEX screen)
Reverse/Forward
16
To adjust the volume of movies
When playing back a movie, touch
(OPTION) tab [VOLUME], then
adjust the volume with / .
Tips
appears with the image on each of the
tab that was lastly played back/recorded. When
you touch image marked with , you can
play it back from the point you have stopped
previously.
Playing the image on a TV
Connect your camcorder to the input jack
of a TV or VCR using the A/V connecting
cable (supplied) or an A/V connecting
cable with S VIDEO (optional). For
details, see “Handycam Handbook” (PDF).
(Yellow)
A/V OUT jack
(White)
(Red)
(Yellow)
: Signal ow
VCR or TVs
DCR-SR55E/SR65E/SR75E/
SR85E
A/V Remote
Connector
DCR-SR35E/SR36E/SR45E/SR46E
Recording/Playback
17
Other parts and functions of the camcorder
Buttons, jacks, etc., which are not explained
in other chapters, are explained here.
Recording/Playback
Power zoom lever
Move the power zoom lever slightly for
a slower zoom. Move it further for a
faster zoom.
You can magnify still images from
about 1.1 to 5 times the original size
(Playback zoom).
When you touch the screen during
playback zoom, the point you touched will
be displayed in the center of the displayed
frame.
Hook for a shoulder belt
Attach the shoulder belt (optional).
Remote sensor (DCR-SR55E/SR65E/
SR75E/SR85E)/Infrared port
Receives the signal from the Remote
Commander.
Built-in microphone
Zoom buttons
Press for zooming in/out.
You can magnify still images from
about 1.1 to 5 times the original size
(Playback zoom).
When you touch the screen during playback
zoom, the point you touched will be
displayed in the center of the LCD screen.
(DISC BURN) button
Create a disc by connecting the
camcorder to a computer. For details,
see “PMB Guide” (p. 25).
DISP/BATT INFO button
You can switch the screen display when
you press while the power is set to on.
When you press while the power is
set to OFF (CHG), you can check the
remaining battery.
(back light) button
Press (back light) to display for
adjusting the exposure for backlit
subjects. Press (back light) again to
cancel the backlight function.
RESET button
Press RESET to initialize all the settings,
including the clock setting.
Speaker
Tripod receptacle (Bottom surface)
Attach the tripod (optional: the length
of the screw must be less than 5.5 mm
(7/32 in.)) to the tripod receptacle using
a tripod screw.
EASY button
Press EASY to display and most
Handycam Station
(DCR-SR55E/SR65E/SR75E/SR85E)
18
of the settings are set automatically for
easy recording/playback. To cancel,
press EASY again.
NIGHTSHOT PLUS switch
Set the NIGHTSHOT PLUS switch
to ON ( appears) to record in dark
places.
QUICK ON button
e QUICK ON lamp ashes and your
camcorder goes to power saving mode
(sleep mode). Press QUICK ON again
to start recording next time. Your
camcorder returns to recording standby
in approximately 1 second.
With [QUICK ON STBY], you can set
the time when the camcorder turns o
in sleep mode.
ACCESS lamp (Hard disk)
When the ACCESS lamp is lit or
ashing, your camcorder is writing/
reading data.
Connecting to the devices
A/V Remote Connector / A/V OUT
jack
Connect with the A/V connecting cable.
(USB) jack
(DCR-SR35E/SR36E/SR55E/SR75E:
output only)
Connect with the USB cable.
Active Interface Shoe (DCR-
SR55E/SR65E/SR75E/SR85E)
e Active Interface Shoe supplies
power to optional accessories such as
a video light, a ash, or a microphone.
e accessory can be turned on or o as
you operate the POWER switch on your
camcorder.
Interface connector
Connect your camcorder and the
Handycam Station.
(DCR-SR55E/SR65E/SR75E/SR85E)
Recording/Playback
19
Indicators displayed during recording/playback
Recording movies
Recording still images
Viewing movies
Viewing still images
HOME button
Remaining battery (approx.)
Recording status ([STBY] (standby) or
[REC] (recording))
Recording mode (HQ/SP/LP)
e recording/playback media
Counter (hour/minute/second)
Recording remaining times
OPTION button
VIEW IMAGES button
Face Index set
Image size
Approximate number of recordable still
images/Recording media
Return button
Playback mode
Currently playing movie number/
Number of total recorded movies
Previous/Next button
Video operation buttons
Data le name
Currently playing still image number/
Number of total recorded still images
Playback folder
Displays only when the recording
media of still images is a “Memory Stick
PRO Duo.”
Slide show button
VISUAL INDEX button
20
Indicators when you made changes
Following indicators appear during
recording/playback to indicate the settings
of your camcorder.
Upper left
Indicator Meaning
Self-timer recording
Flash/REDEYE REDUC
MICREF LEVEL low
WIDE SELECT
BLT-IN ZOOM MIC
Upper right
Indicator Meaning
Fader
LCD backlight o
Drop sensor o
Drop sensor activated
e media selected for
still images
Center
Indicator Meaning
IMAGE SIZE
Slide show set
NightShot plus
Super NightShot plus
Color Slow Shutter
PictBridge connecting
Warning
Bottom
Indicator Meaning
Picture eect
Digital eect
Manual focus
SCENE SELECTION
Back light
White balance
SteadyShot o
EXPOSURE /
SPOT METER
TELE MACRO
Face Index
Tips
Indicators and their positions are approximate
and dier from what you actually see. See
“Handycam Handbook” (PDF) for details.
e recording date and time is recorded
automatically on the media. ey are not
displayed while recording. However, you can
check them as [DATA CODE] during playback.
Upper le Upper right
Bottom Center
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Sony DCRSR82 User manual
-
Sony HANDYCAM DCR-SR45 Operating instructions
-
Sony HANDYCAM DCR-SR46BDL User manual
-
-
-
Sony DCR-SR62E Owner's manual
-
Sony DCR-SR42 User manual
-
Sony DCR-SR38E User manual
-
Sony DCR-SR210E Operating instructions
-
Sony DCR-SR82 Owner's manual