Spirit CE800 ENT Owner's manual

CR800 ENT FITNESS BIKE

OWNER’S MANUAL

TABLE OF CONTENTS

3 IMPORTANT SAFETY INSTRUCTIONS

3 IMPORTANT ELECTRICAL INSTRUCTIONS

4 PRODUCT REGISTRATION

4 IMPORTANT OPERATION INSTRUCTIONS

5 CR800 ENT ASSEMBLY INSTRUCTIONS

11 CONSOLE OPERATION

23 PROGRAMMABLE FEATURES

34 USING HEART RATE TRANSMITTER

37 GENERAL MAINTENANCE

38 MANUFACTURER’S LIMITED WARRANTY

Thank you for purchasing our product, please save these instructions. Please do not perform or attempt any

customizing, adjustments, repair or maintenance that is not described in this manual.

2

Congratulations on your new tness bike and welcome to the Spirit Fitness family!

Thank you for your purchase of this quality tness bike from Spirit Fitness. Your new tness bike was manufactured by one

of the leading tness manufacturers in the world and is backed by one of the most comprehensive warranties available.

Through your dealer, Spirit Fitness will do all we can to make your ownership experience as pleasant as possible for many

years to come. If not purchased direct from Spirit Fitness, the local dealership where you purchased this tness bike is

your administrator for all Spirit Fitness warranty and service needs. Their responsibility is to provide you with the technical

knowledge and service personnel to make your experience more informed and any difculties easier to remedy.

Please take a moment at this time to record the name of the dealer, their telephone number, and the date of purchase below

to make any future, needed contact easy. We appreciate your support and we will always remember that you are the reason

that we are in business.

Yours in Health,

Spirit Fitness

NAME OF DEALER _____________________________________

DEALER PHONE # _____________________________________

PURCHASE DATE _____________________________________

3

Important Safety Instructions

WARNING

• Before beginning this or any exercise program, consult a

physician. This is especially important for persons over the

age of 35 or persons with pre-existing health conditions.

• Keep children away from the tness bike. There are obvi-

ous pinch points and other

caution areas that can cause harm.

• Keep hands away from all moving parts.

• Never drop or insert any object into any openings.

• Do not use outdoors.

• Do not attempt to use your tness bike for any purpose

other than for the purpose it is intended.

• The hand pulse sensors are not medical devices. Various

factors, including the user’s movement, may affect the

accuracy of heart rate readings. The pulse sensors are

intended only as exercise aids in determining heart rate

trends in general.

• Wear proper shoes. High heels, dress shoes, sandals or

bare feet are not suitable for use on your tness bike.

Quality athletic shoes are recommended to avoid leg

fatigue.

• Maximum User Weight: 450 lbs

• This appliance is not intended for use by persons with

reduced physical, sensory or metal capabilities, or lack

of experience and knowledge, unless they have been

given supervision or instruction concerning use of the

appliance by a person responsible for their safety.

• Keep children under the age of 13 away from this

machine.

SAVE THESE INSTRUCTIONS - THINK SAFETY!

Important Electrical Instructions

WARNING

NEVER expose this tness bike to rain or moisture. This

product is NOT designed for use outdoors, near a pool

or spa, or in any other high humidity environment. The

operating temperature specication is 40 to 120 degrees

Fahrenheit, and humidity is 95% non-condensing (no water

drops forming on surfaces).

4

Important Operation Instructions

• NEVER operate this tness bike without reading and completely understanding the results of any operational change

you request from the computer.

• Understand that changes in resistance do not occur immediately. Set your desired resistance level on the computer

console and release the adjustment key. The computer will obey the command gradually.

• Use caution while participating in other activities while pedaling on your tness bike; such as watching television, reading,

etc. These distractions may cause you to lose balance which may result in serious injury.

• Do not use excessive pressure on console control keys. They are precision set to function properly with little nger

pressure.

Record Your Serial Number

Please record the serial number of this tness product in the space provided

below.

Serial Number:

Register Your Purchase

The self-addressed product registration card must be completed in full and returned to Spirit Fitness.

You can also go to http://www.spirittness.com/commercialwarrantyregistration.html under the Support

tab to register online.

Serial Number Location

5

CR800 ENT PRE ASSEMBLY

UNPACKING

1. Cut the straps, then along the dotted line on the bottom of the box; lift the box over

the unit and unpack.

2. Locate the hardware package. The hardware is separated into four steps. Remove

the tools rst. Remove the hardware for each step as needed to avoid confusion. The

numbers in the instructions that are in parenthesis (#) are the item number from the

assembly drawing for reference.

TOOLS INCLUDED:

 14/15mm Wrench

 12/14mm Wrench

 Phillips Screwdriver

PARTS INCLUDED:

 1 Main Frame

 1 Console Mast

 1 Rear Stabilizer

 1 Seat Back Frame

 1 Front Handle Bar

 1 Handle Bar

 1 Seat Back Cover

 1 Console Mast Cover

 1 Front Stabilizer Cover

 1 Rear Stabilizer Cover

 1 Console

 1 Seat Cushion

 2 Cup Holders

 2 Pedals

 1 Hardware Kit

6

CONSOLE FAN

CONSOLE

FRONT STABILIZER

CRANK ARMS

CONSOLE MAST COVER

MAIN FRAME

PULSE GRIPS

CUP HOLDER

REAR STABILIZER

PEDALS

CONSOLE MAST

SEAT

FRONT HANDLEBARS

7

CR800 ENT STEP ONE

4

21

89

77

89

27

175

71

21

6

71

65

84

7

45

44

HARDWARE FOR STEP 1

PART TYPE DESCRIPTION QTY

65 BOLT

3/8”X2-1/4”

4

71 BOLT

3/8”X2”

4

77 FLAT WASHER

3/8”X19

6

84 FLAT WASHER

3/8”X1”

4

89 NYLON NUT

3/8”

6

175 BOLT 3/8X2-3/4” 2

1. Gather HARDWARE FOR STEP 1.

2. Install the REAR STABILIZER (7) onto the

MAIN FRAME with 4 BOLTS (65) and 4

WASHERS (84).

3. Install the HANDLEBAR ASSEMBLY (6) onto

the SEAT CARRIAGE (4) with 4 BOLTS (71)

installed through the top holes and secured with

4 FLAT WASHERS (77) and NYLON NUTS

(89). Install 2 BOLTS (175) through the side holes

and secure with 2 FLAT WASHERS (77) and

NYLON NUTS (89).

4. Plug the LEFT HAND PULSE WIRE (27) into

the corresponding LEFT SOCKET (42) located

in the left plastic side case under the seat carriage,

and the RIGHT HAND PULSE WIRE (21) into

the RIGHT SOCKET (26).

8

CR800 ENT STEP TWO

5

77

4

176

77

176

HARDWARE FOR STEP 1

PART TYPE DESCRIPTION QTY

77 FLAT WASHER

3/8”X19”

6

136 SCREW

M5X15

4

176 BOLT

3/8”X3/4”

6

1. Gather HARDWARE FOR STEP 2.

2. Install the SEAT BACK FRAME (5) onto the

SEAT CARRIAGE (4) with 6 BOLTS (176) and

FLAT WASHERS (77).

3. Install the SEAT BACK COVER (128) onto the

Seat Back with 4 PHILLIPS HEAD SCREWS

(136).

128

136

9

CR800 ENT STEP THREE

3

82

29

68

2

31

68

83

76

30

76

190

191

192

193

44

195

197

1

HARDWARE FOR STEP 3

PART TYPE DESCRIPTION QTY

68 BOLT

5/16”X5/8”

8

76 WASHER

5/16”X11/16”

6

82 SPLIT WASHER

5/16”

2

83 CURVED WASHER

5/16”X3/4”

2

1. Gather HARDWARE FOR STEP 3.

2. Install the CONSOLE MAST COVER (31)

onto the CONSOLE MAST (2), making

sure it is facing the correct direction as in the

picture below. Run the COMPUTER CABLE

(44), HANDPULSE WIRE(195), CSAFE W/

CABLE(190), TV SIGNAL CABLE(191),

NETWORK W/CABLE(192), CONSOLE

POWER CORD(193), and HDMI CABLE(197)

through the bottom of the console mast tube and

out the top opening.

3. Slide the CONSOLE MAST into the

RECEIVING TUBE (1) being careful to not pinch

the wires. Fasten the console mast with 6 BOLTS

(68) and 4 FLAT WASHERS (76) on the side

bolts and 2 CURVED WASHERS (83) on the

front bolts. Snap the CONSOLE MAST COVER

in place.

4. Install the FRONT HANDLEBARS (3) onto the

CONSOLE MAST with 2 BOLTS (68), SPLIT

WASHERS (82) and FLAT WASHERS (76).

10

CR800 ENT STEP FOUR

38

39

105

37

32

99

117

51R

51L

99

2

61

19

186

4

44

197

190

191

192

193

116

99

HARDWARE FOR STEP 4

PART TYPE DESCRIPTION QTY

186 SCREW

M6X18MM

4

99 SCREW

M5X12MM

10

105 SCREW

4MMX16MM

4

1. Gather HARDWARE FOR STEP 4.

2. Install the front and rear STABILIZER COVERS

(32 & 37) and secure to the frame with 4

SCREWS (99).

3. Install the left and right CUP HOLDERS (39

& 38) to the rear handlebars with 4 SELF

TAPPING SCREWS (105).

4. Install the bottom SEAT CUSHION (61) to the

SEAT CARRIAGE (4) with 4 SCREWS (98).

5. Install the PEDALS (116 L, 117 R) into the

CRANK ARMS (51 L, 51 R). Remember that

the left pedal has a reverse thread and will be

screwed in with the opposite rotation. Make sure

to tighten the pedals as much as you possibly can.

6. Connect the 7 WIRE HARNESSES

(44,195,190,191,192,193, & 197) to the

corresponding connectors on the back of

the console. Install the CONSOLE onto the

CONSOLE MAST and secure with 4 SCREWS

(99) being careful to not pinch the wires.

11

CU800 ENT CONSOLE OPERATION

Large Touch-

Screen LCD

Ten innovative

programs offer a

variety of work-outs

Fan to keep

you cool

Easy-Touch

Control Buttons

Convenient cargo

compartment for

keys, phone, or

MP3 player

12

Starting the operation

Plug in the power cord and switch on the main power switch located at the front base of the unit.

When the power is turned on, the screen will show the initial image and then enter the ready mode

which is the beginning of the treadmill operation.

First page for you to operate by touching the

icons.

Quick operating functional buttons are installed.

13

Quick Start

• Press Start button and the console starts performing the program. Press Level up/down buttons

further to change the resistance level you desire.

• Press rst page Home button or Stop button to stop the unit.

Featuring functions of this bike

Touch-control screen is installed for operating the bike. You can directly touch any functional button on

the screen or through quick buttons on the bottom to control. On the bottom, there are the Start

button to begin the workout, Stop button to pause/stop running and Fan button to turn the fan on or

off.

Pause/Stop

• Press Stop button once or Home button on the screen, the bike will stop and keep values of time,

distance and calorie on the screen. The screen will count down for 5 minutes then reset and return

to the initial status.

• Press Start button to continue the workout during pause.

• Press Stop button twice will terminate the setting with displaying the workout summary. If Stop

button is pressed the third time, the console will return to the initial status (the beginning).

14

Heart Rate Feature

The Pulse (Heart Rate) on the screen shows the current value of the heart beats per minute. You must

use both left and right stainless steel sensors to pick up your pulse. Pulse values are displayed anytime

the computer is receiving a Grip Pulse signal. You may use the Grip Pulse feature while in Heart Rate

Control. The Console will also pick up wireless heart rate transmitters that are bipolar compatible,

including signal transmitting.

To Turn Off The Bike

The screen will automatically turn off (go to sleep) after 30 minutes of inactivity. This function is called

sleep mode. In sleep mode, the bike will power down everything except for a minimum of circuitry for

detecting key presses, so it will start up again if this is activated. There is only a tiny amount of current

used in sleep mode (about the same as your TV when it is turned off) and it is perfectly ne to leave

the main power switch on in sleep mode.

15

Touch Screen Operation

Language

There are four items to be selected. Generally the

Language would be the rst item to select.

When you press the Language button on Home

page, it enters the menu with all language

selections.

There are 12 languages to choose. Touch the

desired language, and the system will return to

the rst page to begin the other program, or if

you don’t want to change the language, you could

press Home button at the upper left corner to

return to the rst page or touch the return icon

at right top corner to return to the previous page

to continue your operation.

16

TV

When the TV button on the Home page is pressed, it

directly enters TV interface.

Now you can enjoy TV programs. If you want to enjoy

TV while exercising, press Start button at front of the

treadmill to start it.

You can change the TV channel by using Up/Down

buttons on the TV channel or the channel control

panel buttons at the right side of the screen for quick

channel switching. You can also use up/down buttons

on the volume to change the sound volume. If you

want to be quiet, touch Mute button. Touch Max

Screen to switch to full screen. When you want to

resume the original screen display, just touch the image

and the screen resumes. Use Fast and Slow buttons

to control the speed and Up or Down button to set

the incline level during the exercise. When you want

to pause, just press Home button at left top or press

Stop button once and the pause window will show

up. If you want to stop, you can choose to end the

program or press Stop button again to terminate the

setting and show up the workout summary. If Stop

button is pressed the third time, it returns to the initial

status (the beginning)

17

Internet

When the Internet button on the Home page is

pressed, it directly enters Internet interface.

There are 6 internet connections to choose for you to

go on the internet while you are exercising. (internet

cable connection or WIFI connection is required)

When you want to pause, just press Home button

at left top or press Stop button once and the pause

window will show up. If you want to stop, you can

choose to end the program or press Stop button

again to terminate the setting and show up the

workout summary. If Stop button is pressed the third

time, it returns to the initial status (the beginning)

18

Exercise Programs

When the Exercise Program button on the Home

page is pressed, it directly enters Menu interface.

There are 10 program modes in Menu interface for

you to choose the desired program mode. For Manual

Program as an example, just touch Manual button on

the screen to enter the program for Manual.

MANUAL

Press Prole button to enter the Prole interface. If

this program is unwanted, just press Home icon at left

top to return to the rst page, or return icon at right

top to return to the previous page to continue the last

operation. If other prole is wanted, touch left or right

arrow button to choose the wanted program.

Page is loading ...

Spirit CE800 ENT Owner's manual

This manual is also suitable for

Spirit CE800 ENT Owner's manual

Related papers

Other documents