TOA HY-CN7W-WP User manual

Brand: TOA

Model: HY-CN7W-WP

Category: Speaker mounts

Type: User manual

This manual is also suitable for

INSTALLATION MANUAL

SPEAKER CONNECTION BRACKETS

HY-CN7B, HY-CN7W, HY-CN7B-WP, HY-CN7W-WP

Thank you for purchasing TOA's Speaker Connection Brackets.

Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.

TABLE OF CONTENTS

1. SAFETY PRECAUTIONS ............................. 1

2. GENERAL DESCRIPTION ........................... 1

3. COMPLETE ASSEMBLY

(Joined speaker example using

two HX-7 Series Speaker Systems) ........... 2

JOINING TWO SPEAKER SYSTEMS

............ 2

5. INSTALLING JOINED SPEAKER SYSTEMS

(Indoor installations only) .......................... 6

6. SPECIFICATIONS ........................................ 8

1. SAFETY PRECAUTIONS

• Beforeinstallationoruse,besuretocarefullyreadalltheinstructions in thissection forcorrectandsafe

operation.

• Besuretofollowalltheprecautionaryinstructionsinthissection,whichcontainimportantwarningsand/or

cautionsregardingsafety.

• Afterreading,keepthismanualhandyforfuturereference.

• (HY-CN7BandHY-CN7Wonly)

 Sincethebracketisdesignedforindooruse,donot

install it outdoors. If installed outdoors, the aging

of parts causes the speaker to fall off, resulting in

personal injury. Also, when it gets wet with rain,

thereisadangerofelectricshock.

• Donotuseothermethodsthanspeciedtomount

thebracket.Extremeforceisappliedtothespeaker

and it could fall off, possibly resulting in personal

injuries.

• Tighten each nut and bolt securely. Ensure that

the bracket has no loose joints after installation

to prevent accidents that could result in personal

injury.

• Thebracketisexclusivelyusedtojointogethertwo

HX-7 Series Speaker Systems. Using the bracket

in combination with other speakers may cause the

speaker to fall off, resulting in personal injury.

• Avoid installing the speaker in indoor swimming

facilities that are not well ventilated. In such

locations,themountinghardwaremaybevulnerable

to corrosion, eventually allowing the speaker to fall

resulting in personal injury.

• Avoid touching the bracket's sharp metal edge to

prevent injury.

• Havethebracketcheckedperiodicallybytheshop

fromwhereitwaspurchased.Failuretodosomay

result in corrosion or damage to the bracket that

could cause the speaker to fall, possibly causing

personal injury.

Indicatesapotentiallyhazardoussituationwhich,

if mishandled, could result in death or serious

personal injury.

WARNING

Indicatesapotentiallyhazardoussituationwhich,

ifmishandled,couldresultinmoderateorminor

personalinjury,and/orpropertydamage.

CAUTION

2. GENERAL DESCRIPTION

TheHY-CN7SeriesbracketsareusedtojointogethertwoHX-7Seriesspeakersystemsintoasinglesystem.

Joiningspeakerstogethernotonlyallowsmoreaccuratecontrolofdirectivityforlowerfrequencies,butalso

enhances the audibility of amplied speech in locations that suffer from long reverberation times or high

backgroundnoiselevels.TheHY-CN7BandHY-CN7Wbracketsaredesignedforindoorinstallations,andthe

HY-CN7B-WPandHY-CN7W-WPbracketsareforoutdoorinstallationsundereavesorotherareasprotected

fromdirectexposuretotheelements.

HY-CN7B, HY-CN7W, HY-CN7B-WP and HY-CN7W-WP Speaker Connection Brackets

HX-7 Series speaker

Side angle plate of Speaker

Connection Bracket

Rear angle bar of Speaker

Connection Bracket

Use the brackets to join.

First speaker

Second speaker

Protection cover Speaker molule A Speaker molule B

3. COMPLETE ASSEMBLY

(Joined speaker example using two HX-7 Series Speaker Systems)

4. JOINING TWO SPEAKER SYSTEMS

Be sure to observe the following precautionary instructions.

Doingotherwisecouldresultinspeakersfallingandpotentiallycausing

personal injury.

• Donotjoin5ormoreHX-7SeriesSpeakerSystemstogetherina

single cluster.

• ThreeorfourHX-7SeriesSpeakerSystemsmaybejoinedtogether

only when the specified conditions for mounting brackets and

mountingmethodsaremet.

WARNING

Beforejoiningspeakersystems,layoutaprotectivesheet,corrugatedcardboardorothersoftmaterialonaat

surface,andperformallworkonthe2speakerswiththeirfrontbafesfacingdownward.Itisrecommendedthat

atleasttwopersonsbeinvolvedinjoiningspeakersystems.

Twospeakersystemscanbejoinedtogetherbyconnectingspeakermodules(AandBinthegurebelow)

usingthespeciedbrackethardware.

Note: Position speaker modules A and B facing in the same direction. In the gure, their side angle plate

protectioncoversarevisibleontheleftsideofeachspeakersystem.

Speaker molule A

Hex head bolt removed in Step1-1

Rubber ring removed

in Step1-1

Side angle plate of this bracket

Speacer (golden) removed in Step1-1

Hex head bolt removed in Step1-1

Tightening torque:

3 N·m

Tightening torque:

3 N·m

Speaker molule A

Rubber ring

Speacer (golden)

Hex head bolt

Side angle plate

Hex head bolt

Tighten the bolts securely, as instructed below. Failure to follow

instructions precisely could result in a falling speaker and potential

personal injury.

• Ensurethatallboltsaresecurelyinsertedasfarastheirthreadsgo,

then securely fasten each bolt with a nut.

• Tighten all the bolts with the designated tightening torque. For

tightening,useaPhillipsscrewdriver,oropen-orbox-endwrench.

WARNING

Step 1. DetachthesideangleplateslocatedoneithersideofspeakermoduleA,andreplacethemwiththe

HY-CN7bracket'ssideangleplates.

1-1. Removethe2mountingboltstodetacheachsideangleplate.

Note:Takecarenottolosetheremovedbolts,spacersandrubberrings,astheseareusedinthenext

stepoftheprocedure.

Similarly,replacethesideangleplateontheoppositesideofthespeakermodule.

1-2. AttachtheHY-CN7bracket'ssideangleplatesinthesamepositionwherethespeaker'ssideangle

platesweremounted.

AttachtheHY-CN7bracket'ssideplatesinthereverseordershowninStep 1-1.

Similarly,attachthesideangleplateontheoppositesideofthespeakermodule.

Speaker molule A

Speaker molule B

Speaker molule A

Protection cover

Remove the protection cover from the side angle

plate before joining.

Speaker molule B

Rubber ring

Speacer (golden)

Hex head bolt M6 x 12

(with spring and plain washers)

Tightening torque:

3 N·m

Speaker molule A Speaker molule B

Step 2. JointhesideangleplatesofspeakermoduleAtothoseofspeakermoduleB.

Jointhesideangleplatesusingthesuppliedbolts,spacersandrubberrings.

Step 3. JointherearbracketofspeakermoduleAtothatofspeakermoduleBusingtheHY-CN7bracket'srear

angle bar.

Similarly,jointhesideangleplateontheoppositesideofthespeakermodule.

3-1

Flange nut (for M6, accessory)

Rear bracket of speaker module B

Rear bracket of speaker module A

Speacer (black, accessory)

Rear angle bar of this bracket

Hex head bolt M6 x 25

(with spring and plain washers, accessory)

Tightening torque:

3 N·m

Hex head bolt M6 x 25

(with spring and plain washers, accessory)

Tightening torque:

3 N·m

Fulcrum for the angle adjustment

Rear angle bar of this bracket

Angle adjustment holes

0° mode

15° mode 30° mode

45° mode

[Completed installation (0° mode)]

3-1. AttachtheHY-CN7bracket'srearanglebartotherearbracketofspeakermoduleA.

Usethesuppliedhexheadboltsandnuts.

Fit the spacer (black) into the larger hole in the rear angle bar, then with the angle bar positioned

betweenthe2platesofrearbracketA,andwithholesaligned,inserttheboltthroughtherightmost

holeintherearbracket,andfastenwiththenut.

Notes

• Thispositionwillactasthefulcrumforangleadjustment.Besurethattheanglebarisxedinthe

position indicated in the illustration below. If xed in a different position, the angle mode will not

conformwiththespeciedvalue.

• Besureaspacer(black)isttedintothelargerholeintherearanglebar.

3-2. AttachtheHY-CN7Seriesbracket'srearanglebartotherearbracketofspeakermoduleB.

Usethesuppliedhexheadboltandnut.

Aligntherearanglebarwiththedesireddirectivityanglemodeposition,theninsertaboltandfasten

with a nut.

Thegureshowsamountingexamplewith0°modeselected.

Notes

• Aspacerisnotused.

• Whena60°modeisdesired,usetheoptionalHY-60DSeriesSpeakerAngleAdjustmentBrackets.

Fordetails,refertotheinstallationmanualenclosedwiththeHY-60DSeriesbrackets.

Note

Useamethodsimilar to thatdescribed in Steps 1 – 3above, evenwhenjoiningthree or fourHX-7 Series

Speaker Systems.

Suspension bracket

(accessory of HX-7B

or HX-7W)

For installation method of suspension brackets,

refer to the Installation manual supplied with

the HX-7B or HX-7W.

Note: Optional HY-PF7B or HY-PF7W Speaker Rigging

Frames can also be used.

Rear bracket

Suspension bracket

(accessory of HX-7B

or HX-7W)

Rear angle bar

Rear bracket

5. INSTALLING JOINED SPEAKER SYSTEMS

JoinedtwoHX-7BorHX-7WSpeakerSystemscanbesuspended.

Further,uptofourHX-7BorHX-7Wspeakerscanbesuspendedvertically,providedthatallspeciedoptional

bracketsareusedandotherrequirementsaremet.

5.1. Vertically Suspended Installation

5.1.1. Two-speaker installation

Afterjoiningtogetherthespeakersystems,attachtheirsuppliedsuspensionbrackets(2places)andsuspend

thejoinedspeakerfromthe3pointsshowninthegure.

5.2. Horizontally Suspended Installation

Afterjoiningtogetherthespeakersystems,attachtheirsuppliedsuspensionbrackets(4places)andsuspend

thejoinedspeakerfromthe3pointsshowninthegure.

(Indoor installations only)

5.1.2. Three- or four-speaker installation

TOA’soptionalHY-VM7BorHY-VM7BSpeakerMountingBracketsarerequiredforthisinstallation.

Fordetails,refertotheinstallationmanualsuppliedwiththeHY-VM7BorHY-VM7Bbrackets.

Suspension hole

Suspension bracket

(Speaker's accessory)

Hex head bolt M6 x 20

(with spring and plain washers,

speaker's accessories)

Tightening torque:

3 N·m

[Installation method of suspension brackets]

Tighten the bolts securely, as instructed below. Failure to follow

instructions precisely could result in a falling speaker and potential

personal injury.

• Ensurethatallboltsaresecurelyinsertedasfarastheirthreadsgo,

then securely fasten each bolt with a nut.

• Tighten all the bolts with the designated tightening torque. For

tightening,useaPhillipsscrewdriver,oropen-orbox-endwrench.

WARNING

Beforeinstallingsuspensionbrackets,layoutaprotectivesheet,corrugatedcardboardorothersoftmaterialon

aatsurface,andperformallworkonthe2speakerswiththeirfrontbafesfacingdownward.

Step 1. Removethesideangleplatebolts(indicatedbythearrowsinthegurebelow).

Step 2. Usingtheboltssuppliedwiththespeaker,tightenthesuspensionbracketsandsideangleplates.

Combinethebracketssuppliedwiththe2speakers,andattachthemwiththesuspensionholesfacing

outward,asshowninthegurebelow.

Note:DonotusetheboltsdetachedinStep 1.

URL:http://www.toa.jp/

133-01-00035-01

6. SPECIFICATIONS

ModelNo. HY-CN7B HY-CN7W

Finish Steel plate, black, semi-gross, paint Steel plate, white, semi-gross, paint

Weight 300g(0.66lb)

ProductComposition Sideangleplate.......2,Rearanglebar.......1

ModelNo. HY-CN7B-WP HY-CN7W-WP

Finish Stainless steel, black, semi-gross,

paint

Stainless steel, white, semi-gross,

paint

Weight 300g(0.66lb)

ProductComposition Sideangleplate.......2,Rearanglebar.......1

Note: Thedesignandspecicationsaresubjecttochangewithoutnoticeforimprovement.

• Accessories

Spacer(golden) ............................................................... 2

Spacer(black) ................................................................. 1

Rubber ring ...................................................................... 2

HexheadboltM6x25withspringandplainwashers .... 2

FlangenutforM6 ............................................................ 2

HexheadboltM6x12withspringandplainwashers .... 2

TOA HY-CN7W-WP User manual

Brand: TOA

Model: HY-CN7W-WP

Category: Speaker mounts

Type: User manual

This manual is also suitable for

Download PDF

report

TOA HY-CN7W-WP User manual

This manual is also suitable for

TOA HY-CN7W-WP User manual

Related papers

Other documents