Falcon MLP-300-1 Owner's manual

Brand: Falcon

Model: MLP-300-1

Category: Uninterruptible power supplies (UPSs)

Type: Owner's manual

This manual is also suitable for

MLP-500-1

Falcon electric inc.

MLP SERIES

OWNERS

MANUAL

MLP-300-1 ~ MLP-500-1

MLP SERIES UPS

For Service Call:

(800) 842-6940

* Subject to change without notice.

Falcon Electric Inc., Monrovia, CA. Email. Sales @falconups.com

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

- This manual contains

important instructions for the MLP Series UPS that should

be followed during installation and maintenance of the

UPS and batteries.

CAUTION: All of the MLP models presented herein are designed for installation

and use in a controlled enviroment free of contaniminates.

NOTE: Allow at least 24 hours, after the system is first installed, to fully

charge the internal battery to a maximum state.

CARE & MAINTENANCE

The MLP Series UPS is designed to be maintenance-free. It can be cleaned with a

damp cloth or nonabrasive cleanser providing it is turned off and the input plug

disconnected from the utility source.

Be sure vents are kept free from accumulation of dust, dirt or lint.

Your MLP Series UPS contains sealed maintenance-free batteries (VRLA). When

situated in the proper environment, with the proper charging and limited cycling, these

batteries can last many years.

WARNING

: Never attempt to service batteries. High voltage exists within the unit,

which could cause electrical shock. Servicing of batteries should be performed or

supervised by personnel knowledgeable of batteries and the required precautions.

Keep unauthorized personnel away from batteries. When replacing batteries, use the

same number and type of batteries.

NEVER dispose of batteries in a fire, as batteries will explode.

NEVER dispose of used batteries in the trash or landfill as it is against federal and state

laws. Batteries must be recycled, please contact our service department for the name

and address of the nearest battery recycling facility.

CAUTION - Do not open or mutilate the battery or batteries. Released electrolyte is

harmful to the skin and eyes. It may be toxic.

CAUTION - A battery can present a risk of electrical shock and high short circuit

current. REFER ALL BATTERY SERVICING OR REPLACEMENT TO A QUALIFIED

SERVICE TECHNICIAN. NEVER ATTEMPT TO REPLACE THE BATTERIES

YOURSELF. The following precautions should be observed by a qualified technician

when working with batteries.

1. Remove watches, rings, or other metal objects.

2. Use tools with insulated handles.

2. Wear rubber gloves and boots.

3. Do not lay tools or metal parts on top of batteries.

INSTALLATION AND STARTUP CHECK LIST

1. Verify the following is included in the UPS shipping carton:

• UPS • Software CD • Power Cord

• Owners Manual • UPS/Computer Cable

2. Verify the UPS unit is configured for the proper input/output voltage. This

information is stated on the nameplate label located on the rear panel of the unit.

3. Select a suitable location for the UPS near enough to the computer or equipment

to connect the power cord. Connect the UPS/computer cable to your computer if

applicable. Verify the location you have selected has adequate ventilation to

allow for the proper cooling of the UPS.

DO NOT BLOCK UPS AIR VENTS. THE UPS MUST NOT BE INSTALLED IN

AN ENCLOSED AREA.

4. If unattended computer shutdown and monitoring are desired, connect the

UPS/Computer cable to the DB-9 connector located on the UPS rear panel.

NOTE: If the optional USB to RS-232 converter is to be used, first connect the

Brown RS-232 interface cable to the RS-232 port on the UPS and connect the

other end to the RS-232 connection located on the USB converter. Next connect

the USP connector coming from the USB converter to a free USB port on the

computer or attached USB hub.

5. Connect the equipment to be protected to the output receptacles located on the

UPS rear panel. Verify that the connected equipment does not exceed the rated

output of the MLP UPS.

6 Plug the UPS power cord into the nearest grounded

wall outlet. The UPS should

power ups at this point

The UPS should be left turned on for 24 hours to charge the internal

batteries. Please remember during this initial 24 hour charging period,

battery backup time will be substantially shorter than normal.

7. Turn on the connected equipment and verify the UPS does not go into

overload using the front panel LED indicator. SEE TABLE BELOW.

LED

Condition

Green Orange Red None

Audible

Alarm

AC Mode

Battery Mode

Defective Battery

or Overcharging

Overload

Low Battery Cut

Off

REAR PANEL LAYOUT

1. Output receptacles

2. N/A

3. Communications port

4. Phone/Modem surge protection

5. AC input power cord

Input fuse

OPERATION

1. Turning The MLP UPS On and Off

All MLP models will automatically turn on when the input plug is plugged in. To

turn the UPS off press the On/Off button located on the UPS front panel for five

seconds. To turn the UPS on again press the On/Off button for five seconds.

2. DC Start

To start the UPS when AC utility power is not available, press and hold down the

On/Off button for five seconds.

3. Green Power Function

All MLP UPS models are equipped with a Green Power function. If no load is

present at the UPS output receptacles (no equipment connected or equipment

turned off) the UPS will shutdown within two minutes. Should the utility AC be

loas during the shutdown, the UPS will automatically restart and again shutdown

after another two minutes on no load being applied.

4. Charging

The MLP UPS is shipped from the factory with it’s batteries fully charged,

however some charge may be lost due to self discharge chacteristics of the

internal battey. Allways allow the UPS to recharge for 24 hours prior to use.

Simply connect the UPS line cord to a powered receptacle and allow to recharge.

During noral use the UPS will self recharge should the battery be depleted due to

a loss of utility power.

Trouble Shooting

Symptom Possible Cause Remedy

1.Missing battery 1. Charge battery for 24 hours

2. Battery defective 2. Have the battery replaced

No LED display on

the front panel

3. Power switch was not pressed

for at least 5 seconds

3. Hold the power button for 5 seconds

Continious Alarm hile

on Utiltiy

UPS overloaded Verify the connected load is under the

UPS rated output.

1. UPS overloaded 1. Remove some of the non-criticle load.

2. Battery not fully recharged 2. Charge battery for 24 hours.

Short backup time

3. Battery defective 3. Have the battery replaced

1. Software is improperly installed

or configured.

1. Check settings in software or reinstall

software.

Loss of

communications

beteen UPS and

computer

2. UPS interface cable or USB

cable is disconnected or became

defective

2. check all cable connections.

1. UPS input fuse has blown. 1. Replace fuse with the same type and

rating.

Utility is normal but

LED indicator is

Orange.

2. Power cord is loose or

disconnected

2. Reconnect the input plug to another

receptacle.

SPECIFICATION

MODEL

MLP-300-1 MLP-500-1

Nominal Voltage 120Vac

Voltage Range 80-143Vac

Current 3.6A 6.0A

INPUT

Frequency

50/60Hz ±5% (auto detecting)

VA 300 500

Voltage 120Vac

On Line Voltage Regulation

±10%

On Battery Voltage

Regulation

±10%

AVR Operation

Buck AVR (down/up)

Boost AVR (up/down)

126/121Vac

103/108Vac

Power 180W 300W

Current

2.9A 4.9A

Frequency

50/60Hz ±1 Hz

Waveform Step Wave (modified sine wave)

Transfer Time

Bypass to Inverter

Inverter to Bypass

<10 ms

<2 ms

Surge Protection Metal Oxide Varistor

OUTPUT

Protection Short circuit & overload, Excessive battery discharge & overcharge

DC Voltage 12Vdc

Type 12V, 5AH, HC1221W

Recharge Time to 90% 8 Hours

BATTERY

Run time 100%

50%

4.2min. typ.

21min. typ.

3.4 min. typ.

9.6 min. typ.

Buck and Boost with Auto Voltage Regulator

Fax/Modem Surge Protection

DC Cold Start

FEATURES

Special

Green Mode Operation

Audible

Alarms

On Battery (6 sec. intervals)

Low Battery (1 sec. Intervals)

Overload (continuous)

Indicators

L.E.D.

AC Normal – Green

On Battery – Orange

Battery Defective, Overcharging, Low Cut-off - Red

Control

Type Microprocessor

Computer True RS-232

Interface

Options USB Converter cable, UPSILON shutdown & management software

Temperature

0°C - 40°C (32°F – 104°F)

Humidity 10% - 90% Non-condensing

Environment

Max. Altitude 5000 feet (1500 meters)

Input Cord 6 Foot Cord with 5-15P

Output Receptacles (2) NEMA 5-15R

Weight 15.4 lbs. (7kg)

Mechanical

Dimensions (mm)

H x W x D inches

(180 x 78 x 320)

7.09 x 3.07 x 12.6

Approvals

Agency UL, FCC Class A

1 Computer load.

2 Backup times are for reference only. Actual duration may vary depending on temperature, battery condition and type of load.

3. Models are available with a contact closure computer interface. For these models add a “C” to the end of the desired model number.

Falcon MLP-300-1 Owner's manual

Brand: Falcon

Model: MLP-300-1

Category: Uninterruptible power supplies (UPSs)

Type: Owner's manual

This manual is also suitable for

MLP-500-1

Download PDF

report

Falcon MLP-300-1 Owner's manual

This manual is also suitable for

Falcon MLP-300-1 Owner's manual

Related papers

Other documents