Rockford Fosgate RFQ5000 Setup Instructions

Brand: Rockford Fosgate

Model: RFQ5000

Category: Car audio amplifiers

Type: Setup Instructions

Rockford Fosgate RFQ5000 is a surround sound processor that is designed to enhance the listening experience for both music and movie soundtracks. It features five-channel discrete surround sound processing and can decode all modes of surround sound, including Dolby Digital, AC-3, 5.1, or DTS. The RFQ5000 also has a panorama control that allows you to adjust the width and depth of the stereo image, and output level adjustments so that each channel has the same amplitude at the drivers seat listening position.

INTRODUCTIOn

What is the RFQ5000?

The RFQ5000 is a surround sound processor that is designed to enhance the listening experience

for both music and movie soundtracks. The RFQ5000 is the brainchild of Jim Fosgate. Jim intro-

duced the first Fosgate car amplifier in 1973! Since 1980 Jim has been perfecting the art of sur-

round sound, both in the home and the car. The RFQ5000 is the culmination of Jim’s efforts com-

bined with Rockford Fosgate engineering. The result is a processor that delivers pinpoint, precise

imaging with music, and superb sound effects typical of movies. Because the RFQ5000 has only

analog inputs and works totally in the analog domain, it works with ANY source, even existing sys-

tems. The RFQ5000 will properly decode Dolby Digital™, AC-3™, 5.1, or DTS™ encoded record-

ings. It also works wonders for traditional two channel recordings. If you are an audio fanatic or a

competitor, the RFQ5000 will amaze you with its ability to deliver a lifelike stereo image. The

RFQ5000 is truly a revolution in surround sound technology. Hear all your music again…for the

first time!

The RFQ5000 is not…

The RFQ5000 is not a digital signal processing echo box! There is no digital processing done

inside it, and it will not mimic the acoustic properties of your local football stadium. The

RFQ5000 simply produces what the artist intended. Whatever the source, movie soundtracks,

audiophile compact discs, or 10 year old cassette tapes, the RFQ5000 will reproduce them like no

other processor. Movies come alive with sound effects. Music is produced with amazing accuracy,

pinpoint imaging, and a sense of air and space that opens up the typical confined listening

environment of the vehicle.

specifications

Operating Voltage +10V to +16VDC

Current Consumption 500mA

B+ Fuse Size (internal) 2 Amp

Frequency Response within one half db +/- 10hz to 50khz

Signal-to-Noise Ratio better than 90db A weighted

Distortion (THD + Noise) 0.5% @ 2v rms output @ 1 khz

Maximum Output Level 4 volts rms

Number of Channels 5

Number of Inputs 4 RCA

Number of Outputs 7 RCA

Dimensions 6.80”W x 8.14”L x 1.08”H

(without mounting flange) (17cm x 20.35cm x 2.7cm)

Dimensions 7.78”W x 8.07”L x 1.08”H

(with mounting flange) (19.45cm x 20.17cm x 2.7cm)

Specifications are subject to change without notice.

technical design features

Five channel discrete surround sound processing – Utilizing high speed voltage controlled ampli-

fiers, the RFQ5000 accurately decodes all modes of surround sound and sends the discrete

information to each of 5 individual channels.

Panorama control – The RFQ5000 works with any two channel analog source, but if the source

unit has dual pre-amp outputs (like all Rockford Fosgate source units) you can take advantage of a

feature called panorama control. Panorama control converts the fader in the source unit to a con-

trol that varies the width and depth of the stereo image. By simply fading from front to rear, you

adjust the panorama control.

Output level adjustments – these internal controls are used to adjust the individual output channels

of the RFQ5000, so that each channel has the same amplitude (SPL) at the drivers seat listening

position.

LF Gain: controls the signal level of the left front output

RF Gain: controls the signal level of the right front output

CF Gain: controls the signal level of the center front output

LB Gain: controls the signal level of the left back output

RB Gain: controls the signal level of the right back output

L SUB Gain: controls the signal level for the left subwoofer output

R SUB Gain: controls the signal level for the right subwoofer output

Center Channel Adjustment - By turning this control you adjust the relative focus of the center

channel from wide & diffuse to very precise & pinpoint. While listening to a track with center

channel information, simply adjust this control until the center channel blends properly with the left

and right front speakers.

ADJUSTMENT

CENTER CHANNEL

RV11

RV9

RV7

RV4

RV2

R SUB GAIN

L SUB GAIN

RB GAIN

LB GAIN

CF GAIN

RF GAIN

LF GAIN

SURROUND SOUND PROCESSOR

MADE IN USA

ROCKFORD CORPORATION

PC-2804-D

J16

R197

C85

C84

C83

C82

R195

C65

C64

C63

C62

C61

C51

C50

C49

C48

C47

U17

U16

U15

U14

U13

U12

U11

C45

C44

C43R190

R189

R188

R187

R186

R185

R184

R183

R182

R181

R168

R167

J29

R164

R163

R160

R158

R156

J28

R146

J27

R145

R144

R143

J26

R142

R141

R140

R139

R138

C37

R137

R136

R135

C36

R134

C35

R133

R132

R131

C34

R130

C33

R129

R128

R127

R126

R124

R122

R120

R96

R95

R94

R93

R91

C24

R83

R50

R49

R48

R47

R46

R45

R41

C11

R33

J29

External controls and adjustments

Center Channel ON/OFF switch:

Turn this switch to ON if the system uses a dedicated center channel speaker. When set to the

OFF position, the RFQ5000 sends center channel information to the left and right front speakers.

Optimum sound quality is achieved by using a dedicated center channel speaker.

Remote LED Display

With proper set-up the RFQ5000 will provide an enjoyable listening environment without the need

for further adjustment. If you find yourself in a situation where the signal to the RFQ5000 is not

stereo, (weak or AM radio like), you will need to press the button on the Remote LED display to

deactivate the “steering logic” until the stereo FM signal returns. When the button is “out” the

Center Channel information is distributed evenly among all channels.

The Remote led display will illuminate each LED when audio information is sent to that channel.

With normal use the Center Channel will appear to have most of the information. This display

should not be used to adjust the signal levels when setting up the primary unit.

INSTALLATION AND SET-UP

Proper set-up of the RFQ5000 is critical and is achieved by using the supplied compact disc, and a

SPL (sound pressure level) measuring device. Battery operated SPL measuring devices are available

for as little as $50, and will work adequately with the pink noise signal supplied on the test CD.

It is necessary to adjust the output of the RFQ5000 for optimum performance so that each main

speaker reproduces equal SPL. Use the output adjustment potentiometers to achieve this. If addi-

tional range is necessary to match the output levels, simply adjust the amplifier gain to compen-

sate.

Tracks 1, 2, 3, 10 and 11 on the CD are a bandwidth limited pink noise signal that rotates in a

clockwise pattern in the following order; LF-CF-RF-RB-CB (phantom center)-LB and then repeats for

a total of 5 minutes. Use these tracks to ensure that the processor and the amplifiers are wired to

the proper speaker locations. These tracks can also be used to confirm the relative SPL of each

location.

Tracks 4, 9, and 12 through 17 are used to set the levels of each channel so they produce equal

SPL. Simply select the track that corresponds to the channel you wish to adjust. The SPL meter

should be held in a position that is equal in distance from the driver and passenger listening posi-

tions on a plane equivalent to ear level.

Tracks 18 is panned pink noise starting at left front and rotating around the front, then ending at

right front.

Track 19 is panned pink noise starting at left front and rotating around the back, then ending at

right front.

The subwoofer outputs may be adjusted by ear, as the woofers are unaffected by the surround

sound process. Additionally, if the system you are using has subwoofer control from the dashboard

via a source unit or preamplifier, you may wire the woofers directly from the source unit to the

woofer amplifiers. It is not mandatory to use the subwoofer outputs of the RFQ5000.

The subwoofer outputs on the RFQ5000 are supplied as a convenience feature.

Tips for Optimum Performance

Use five identical speakers if possible. This assures that the tonal qualities of each channel will be

similar, and differences can easily be corrected with equalization. If it is not possible to have the

center channel identical to the other speakers, use the closest substitute. The quality of the center

channel speaker will have a great effect on the overall sound quality of the system.

After the 5 main channels are adjusted to match in level, you may then experiment to find the

balance between channels that works best in your system. Depending on the location of the driv-

ers, you may find that reducing or raising the gain on some channels produces a more pleasing

effect.

In some systems a reduction of high frequency output of the rear speakers may improve the overall

sound quality. Our suggestion is to begin with a slight cut at about 2-4khz, end with about a 6 dB

cut at 20khz. This may be achieved with outboard equalization.

If your system has subwoofer output that is controlled from the dashboard of the car you may send

the subwoofer signal directly to the subwoofer amplifier(s). The RFQ5000 has no effect on low fre-

quencies and the subwoofer outputs are for use in systems with no front controlled subwoofer

output. EATUres

Accessory Pack

(1) Set-up CD

(4) Mounting Screws

(1) Power Connector

(1) Bracket

(2) Bracket Mounting Screws

Installation Considerations

The following is a list of tools you will need for installing the RFQ5000

Red power wire Wire strippers

Blue remote turn-on wire Wire cutters

Black grounding wire Voltmeter

Electric hand drill w/assorted bits Battery post wrench

Jeweler's slotted screwdriver

This section focuses on some of the vehicle considerations for installing your new RFQ5000.

Pre-planning your system layout and best wiring routes will save installation time. When decid-

ing how to lay out your new system, be sure that each component will be easily accessible for

making adjustments.

Before beginning any installation, be sure to follow these simple rules:

1. Be sure to carefully read and understand the instructions before attempting to install the

RFQ5000.

2. For safety, disconnect the negative lead from the battery prior to beginning the installation.

3. For easier assembly, we suggest you run all wires prior to mounting your RFQ5000 in

place.

4. Route all of the RCA cables close together and away from any high current wires.

5. Use high quality connectors for a reliable installation and to minimize signal or power

loss.

6. Think before you drill! Be careful not to cut or drill into gas tanks, fuel lines, brake or

hydraulic lines, vacuum lines or electrical wiring when working on any vehicle.

7. Never run wires underneath the vehicle. Running the wires inside the vehicle provides the

best protection.

8. Avoid running wires over or through sharp edges. Use rubber or plastic grommets to

protect any wires routed through metal, especially the firewall.

9. ALWAYS protect the battery and electrical system from damage with proper fusing. Install

the appropriate fuseholder and fuse on the +12V power wire within 18” (45.7 cm) of the

battery terminal.

10. When grounding to the chassis of the vehicle, scrape all paint from the metal to ensure a

good, clean ground connection. Grounding connections should be as short as possible and

always be connected to metal that is welded to the main body, or chassis, of the vehicle.

mounting location

The RFQ5000 consist of a primary unit and the Remote led display. The primary unit can be

mounted in any location in the vehicle, however here are a few suggestions that may make set-up

and installation easier.

Mount the primary unit close to the amplifiers, this will make running the RCA cables easier and

shorter to the amplifiers.

Mount the Remote LED display display unit in the front of the vehicle interior so as not to obstruct

the view of the driver but in a location where the bypass button is accessible.

Hint: For the initial set-up and installation have the RFQ5000 in an easy to get at location, i.e. on

extra long cables or outside the car. This will make the control adjustments easier to get at.

Wiring the System

For safety, disconnect the negative lead from the car battery prior to beginning the installation.

The supplied connector will have three locking screws to attach the power, ground and remote

turn on. The connections should read (GND) Ground, (B+) Battery positive and (REM) Remote turn

on, from the top down as you look at the unit.

1. Wire the Power Connector

The B+ lead should be connected to a source of non-switched 12 volts DC. Prepare a length

of cable from the constant +12V by stripping

" of insulation from the end of the wire. Insert

the bared wire into the B+ terminal of the power connector and fasten the screw.

NOTE: The B+ lead of the audio system MUST be fused 18" or less from the vehicle's battery.

Install a fuseholder, along with the necessary fuse, under the hood. Connections should be

water tight.

The REM lead should be connected to the remote turn-on or power antenna output from the

source unit. Prepare a length of cable from the source of switched voltage by stripping

" of

insulation from the end of the wire. Insert the bared wire into the REM terminal of the power

connector and fasten the screw. Total current consumption through this lead is negligible.

The GND lead should be connected to the chassis ground of the vehicle. Prepare a length of

cable (approximately 12" long) to be used for the ground lead by stripping

" of insulation

from each end. Insert one end of bared wire into the GND terminal of the power connector

and fasten the screw. Prepare the chassis ground by scraping any paint from the metal surface

and thoroughly clean the area of all dirt and grease.

Strip the other end of the wire and attach a ring connector. Fasten the cable to the chassis

using a non-anodized screw and star washer.

2. Connect the Source Inputs

Connect the front RCA outputs from the source unit to the “LEFT FRONT IN” and “RIGHT

FRONT IN” connectors on the RFQ5000.

Refer to page 3 “Panorama Control” for details on rear inputs.

3. Connect the Outputs

Connect the appropriate outputs from the RFQ5000 to the corresponding inputs on the amplifi-

er(s) or signal processor(s).

Wiring the System

System Diagram

Left Front Center Front Right Front

Left Rear Right Rear

Center Channel

Switch Set to

“ON”

Not

Used

1k-20kHz

0dB +10dB

-10dB +10dB

1kHz

-10dB +10dB

250Hz

-10dB +10dB

Frequency

40Hz 80Hz

Subwoofer

Sub Volume

R Fader F

Volu me

Input

A/B

Sub Out

2-Channel or Mono Amp

5-Channel Amp

BAND

DISP AS

LOUDMODE

MUTE

TUNE

123456

SEL

VOL

COMPACT DISC PLAYER WITH DIGITAL TUNER

RPT

TRACK

SCAN

RDM DISC

PUSH

SEEK

ST RPT RDMLOUDLOCAL

CD CHANGER CONTROL

5-Channel System with in dash Pre-Amp

or Source Unit with Subwoofer Output

System Diagram

Left Front Center Front Right Front

Left Rear Right Rear

Center Channel

Switch Set to

“ON”

2-Channel or Mono Amp 5-Channel Amp

BAND

DISP AS

LOUDMODE

MUTE

TUNE

123456

SEL

VOL

COMPACT DISC PLAYER WITH DIGITAL TUNER

RPT

TRACK

SCAN

RDM DISC

PUSH

SEEK

ST RPT RDMLOUDLOCAL

CD CHANGER CONTROL

System using Subwoofer out of RFQ5000

Troubleshooting

Symptom Diagnosis Remedy

RFQ5000 does not

turn on (Power LED

is off)

RFQ5000 has no

sound (Power LED

is on)

Voltage applied to the REM

terminal of the RFQ5000 is not

between 5 and 15.5 volts.

Check the alternator, battery, fuse and

wiring and repair as necessary. If the

voltage is above 15.5 volts, have the

electrical system inspected

by an authorized car

service center.

Voltage to the B+ terminal of

the RFQ5000 is not between 5

and 16 volts or there is no

voltage present.

Check the alternator, batter, fuse and

wiring and repair as necessary. If the

voltage is above 15.5 volts, have the

electrical system inspected by an

authorized car service center.

Internal B+ fuse is blown

Remove cover from RFQ5000 an

replace with 2 amp fuse.

RFQ5000 is not properly

grounded.

Check wiring and repair as necessary.

RCA Input from source unit

is not connected or not

functioning properly.

Check connections, substitute with

known working source and cables, and

repair or replaces as necessary.

Output attenuators are

at minimum.

Readjust output attenuators

as necessary.

Turn-On Pop

Voltage spike from output of

preceding component is

entering RFQ5000 through

input signal.

Disconnect input signal to RFQ5000

and turn unit on and off. If noise is

eliminated, connect REM lead of

RFQ5000 to remote turn-on wire with a

delay module.

Bad component in the

signal chain.

Check connections and bypass additional

components (crossovers and preamps)

between the source unit and the amplifier.

Connect one component at a time using

muting plugs (RCA signal shorted to

shield) at the input of each added compo-

nent to determine the culprit. Repair or

replace components as necessary.

Multiple grounds in the

audio system.

Check ground connections and connect

amplifiers, signal processors, and other

components to a central location or try a

different grounding point on the chassis.

The test signal

from the Set-up

CD does not

appear on the

correct channel

RCA out not properly

connected.

Check the RCA out from the RFQ5000

are going to the proper amp.

Troubleshooting

Symptom Diagnosis Remedy

Output attenuators set to

minimum or incorrectly set.

Readjust output attenuators as necessary.

Refer to Installation section of this manual

for proper level adjustment.

Source unit output too low or

source unit has no output.

Check system with known working source

and repair or replace original source as

needed.

Noise is radiating into RCA

signal cable.

Check connections and run the RCA

cables on a different route away from

sources of high current.

Distorted or Low

Output

Engine Noise

Troubleshooting

Symptom Diagnosis Remedy

One channel louder

than the others.

Internal amplifier adjustments

not correct.

Check the internal adjustment or the

gain adjustment on the amplifier

limited warranty

Rockford Corporation offers a limited warranty on Rockford Fosgate products on

the following terms:

•

Length of Warranty

- 3 years on electronics - 90 days on electronic B-stock (receipt required)

- 1 years on source units - 90 days on speaker B-stock (receipt required)

- 1 year on speakers

•

What is Covered

This warranty applies only to Rockford Fosgate products sold to consumers by Authorized Rockford

Fosgate Dealers in the United States of America or its possessions. Product purchased by consumers

from an Authorized Rockford Fosgate Dealer in another country are covered only by that country’s

Distributor and not by Rockford Corporation.

• Who is Covered

This warranty covers only the original purchaser of Rockford product purchased from an

Authorized Rockford Fosgate Dealer in the United States. In order to receive service, the purchaser

must provide Rockford with a copy of the receipt stating the customer name, dealer name, product

purchased and date of purchase.

• Products found to be defective during the warranty period will be repaired or replaced (with a

product deemed to be equivalent) at Rockford’s discretion.

• What is Not Covered

1. Damage caused by accident, abuse, improper operations, water, theft.

2. Any cost or expense related to the removal or reinstallation of product.

3. Service performed by anyone other than Rockford or an Authorized Rockford Fosgate Service

Center.

4. Any product which has had the serial number defaced, altered, or removed.

5. Subsequent damage to other components.

6. Any product purchased outside the U.S.

7. Any product not purchased from an Authorized Rockford Fosgate Dealer.

• Limit on Implied Warranties

Any implied warranties including warranties of fitness for use and merchantability are limited in

duration to the period of the express warranty set forth above. Some states do not allow limitations

on the length of an implied warranty, so this limitation may not apply. No person is authorized to

assume for Rockford Fosgate any other liability in connection with the sale of the product.

• How to Obtain Service

Please call 1-800-669-9899 for Rockford Customer Service. You must obtain an RA# (Return

Authorization number) to return any product to Rockford Fosgate. You are responsible for shipment

of product to Rockford. Always include Proof of Purchase and write RA# on outside of shipping

carton.

Rockford Corporation

Warranty Repair Department

2055 E. 5th Street

Tempe, AZ 85281

RA#:_________________

INSTALACION DEL RFQ5000 - ESPAÑOL

Lea detenidamente las siguientes instrucciones de instalación del producto.

La preparación adecuada del RFQ5000 es esencial, y se logra utilizando el disco compacto inclui-

do y un dispositivo para medir el SPL (nivel de presión de sonido). Los dispositivos de medición de

SPL que funcionan a batería están disponibles por tan sólo $50, y funcionarán en forma adecuada

con la señal de ruido rosado provista en el disco compacto de prueba.

Es necesario ajustar la salida del RFQ5000 para lograr un resultado óptimo, de modo que cada par-

lante principal reproduzca un SPL equivalente. Use los potenciómetros de ajuste de salida para este

paso. Si es necesario un alcance adicional para igualar los niveles de salida, ajuste simplemente la

ganancia del amplificador para

compensar.

Las bandas 1, 2, 3, 10 y 11 del disco compacto son señales de ruido rosado limitado por ancho de

banda que gira en una configuración en el sentido de las agujas del reloj en el orden siguiente: ID

– CD – DD – DT – CT (centro fantasma)-IT y luego se repite durante un total de cinco minutos.

Use estas bandas para asegurar que el procesador y los amplificadores están conectados a los

lugares de parlantes adecuados. Estas bandas también pueden utilizarse para confirmar el SPL rela-

tivo de cada lugar.

Las bandas 4, 9 y 12 a 17 se utilizan para fijar los niveles de cada canal para que generen un SPL

equivalente. Seleccione simplemente la banda que corresponda al canal que desea ajustar. El

medidor de SPL debe sostenerse en una posición que esté a la misma distancia de los lugares

desde los cuales escuchan el pasajero y el

conductor en un plano equivalente al nivel del oído.

La banda 18 es ruido rosado panorámico que comienza adelante a la izquierda y gira alrededor

del frente, luego finaliza adelante a la derecha.

La banda 19 es ruido rosado panorámico que comienza a la izquierda adelante y gira alrededor de

la parte posterior, luego finaliza adelante a la derecha.

Las salidas del subwoofer pueden ajustarse de oído, ya que los woofers no se ven afectados por el

proceso de sonido ambiental. Además, si el sistema que está utilizando tiene control de subwoofer

desde el tablero mediante una unidad de fuente o un preamplificador, usted puede conectar los

woofers directamente de la unidad de fuente a los amplificadores del woofer. No es obligatorio

usar las salidas del subwoofer del RFQ5000. Las salidas del subwoofer del RFQ5000 se proveen

para su conveniencia.

Cableado del conector

El terminal B+ debe ser conectado a una fuente no conmutada de 12V continuous. Prepare un

cable de la longitud adecuada desde la fuente de 12V+ y pele 1cm de aislante del cable en el

extremo que vaya a conectar al aparato. Inserte

el cable pelado en el orificio B+ del conector y asegúrelo con el tornillo.

NOTA: El terminal B+ de sistema de audio debe estar protegido con un fusible no más lejos de

45cm de la bateria. Instale un portafusibles y el correspondiente fusible en el compartimento del

motor. Las conexiones deben ser resistentes al agua.

El terminal REM ha de conectarse al terminal remote o antena de su radio-cassette. Prepare un

cable de la longitud adecuada desde la fuente y pele 1cm de aislante del cable en el extremo que

vaya a conectar al aparato. Inserte el cable pelado en el orificio REM del conector y asegúrelo con

el tornillo. El consumo

de corriente de este terminal es despriciable.

De ser posible, use cinco parlantes idénticos. Esto asegura que las calidades tonales de cada canal

sean similares, y las diferencias se puedan corregir fácilmente con la ecualización. Si no es posible

lograr que el canal central sea idéntico a los otros parlantes, use lo más parecido que tenga. La

calidad del parlante de canal central tendrá un gran efecto sobre la calidad general de sonido del

sistema.

Después de haber ajustado los cinco canales principales para igualar su nivel, puede luego experi-

mentar para encontrar el equilibrio entre canales que mejor funcione en su sistema. De acuerdo a

la ubicación de los parlantes, encontrará que la reducción o el aumento de la ganancia en algunos

canales produce un efecto más placentero.

En algunos sistemas, una reducción de la salida de alta frecuencia en los parlantes posteriores

puede mejorar la calidad general del sonido. Nuestra sugerencia es que comience con una ligera

reducción alrededor del extremo de 2-4 khz, y termine con una reducción de 6 dB en 20 khz. Esto

puede realizarse con una ecualización exterior. Si su sistema tiene una salida de subwoofer que se

controla desde el tablero del auto, puede enviar la señal del subwoofer directamente al amplifi-

cador o amplificadores del subwoofer. El RFQ5000 no tiene efecto sobre las bajas frecuencias y las

salidas del subwoofer son para ser utilizadas en sistemas sin salida de subwoofer delantera

controlada.

Page is loading ...

Rockford Fosgate RFQ5000 Setup Instructions

Brand: Rockford Fosgate

Model: RFQ5000

Category: Car audio amplifiers

Type: Setup Instructions

Download PDF

report

Rockford Fosgate RFQ5000 Setup Instructions

Rockford Fosgate RFQ5000 Setup Instructions

in other languages

Related papers

Other documents