PART CODE: 1100083445
Bring Home Innovation
Bring Home Videocon
Fully Automatic Washing Machine
Please read this manual carefully beforeinstruction
operating your machine. Retain it for future reference.
Record model name & serial number of the machine.
Please quote this information when you require service.
2nd Proof - 20-10-11
Fully Automatic - VT55A11 - VT60A12
Shri. Nikhil Kulkarni - Chaitanya sir
From Rajmudra
Positive - 22-10-11 supply
Message from the Vice Chairman & CEO
Page-1
spinning. The Fuzzy mode checks for the following before deciding on the
Wash Parameters :
Feature
=
=
=
=
=
=
=
=
=
=
Intelligence of Digital Sensi logic for superior wash quality
machine to make parametersindependent judgement regarding wash process on
like water level washing, rinsing andrequirement, wash cycle time for soaking,
Self-Dry Load Sensing : The machine automatically selects the optimum water
level after sensing the cloth load.
Memory Backup
In case of a power failure ( while the machine is functioning ), the machine shall
automatically complete the remaining part of the selected cycle after the power
resumes. This is due to the memory back up feature.
Auto Balancing
This mechanism works during spinning. In case of the clothes getting collected on
a side of the tub, the fully automatic washing machines are provided a mechanism
where in the machine shall stop the spinning operation & shall distribute the
Auto Error Indication
If any of the following errors occur during the course of washing, your machine
indicates it by the blinking of the LEDs on the control panel and audio indication
Dry tap
Lid open while spinning
Drain Block
Imbalance while spinning
Unique AUTO SOAK option
Soaking is an important element of the washing process. It enhances and
optimizes the detergent’s action on the clothes. This ensures that dirt & stain are
easily removed and thus enhance the wash quality.
8 Wash Programmes
Normal
Strong
Saree
Wool
Normal + Soak
Strong + Soak
Saree + Soak
Wool + Soak
=
Child Lock
To prevent stoppage of machine cycle by a naughty child, your machine has Child
key same time while cycle is in process. a long beep is heard as an
acknowledgment of lock/unlock.
Lock facility. You can lock/unlock the control panel by pressing Program+Process
clothes uniformly in the tub. The spinning shall resume there after.
The closest you can get to a Human wash, Digital Sensi Control enables the
as follows :
Tap
Tape
Lock
Lever
Water supply
hose cover
A
B
Approx. 4mm
Adapter
Screws (4)
Water Tap
Accessories
Water supply hose
Drain hose
Tap adapter
Anti Rat Mesh Instruction Manual
Softener
inlet
Control Panel
Water Tap
Plastic Base
Tap Adaptor
Feed Valve
Tub
Lint Filter
Drain hose
Pulsator
Lid
Bleach
inlet
Do not tie the power cord in a bundle during operation
Power cord
Parts Identification
Installation
Page-4
Key press functions
Page-5
Settings
During "Child Lock" mode no button can be operated.
"Child Lock" can be activate after you start the cycle.
Ex. Dry
Ex. Dry is in Process Selection Key, one additional selection is available,
the selection will be indicated by Blinking of Fuzzy LED. The machine
will 28 Min and go Off.spin for
VT60A12
WASH
RINSE
SPIN
SOAK
NORMAL
STRONG
SAREE
WOOL
DETERGENT
FUZZY/ EX. DRY
52L / 56L
40L / 48L
28L / 36L
20L / 24L
POWER
START
HOLD
CHILD LOCK
WATER PROGRAM PROCESS
2 43
1
5
6
VT55A11
WASH
RINSE
SPIN
SOAK
NORMAL
STRONG
SAREE
WOOL
DETERGENT
FUZZY
47L / 52L
37L / 42L
27L / 32L
17L / 22L
POWER
START
HOLD
CHILD LOCK
WATER PROGRAM PROCESS
2 43
1
5
6
Process
Press this button to
choose process
(wash, spin, rinse,
ex dry).
After pressing of
this button, machine
come out from Fuzzy
mode.
4
Water Level
Press ths button to
choose any water level
you want, after press
this button, machine
comes out from Fuzzy
mode and LED indicate
actual water level in
manual mode.
2
Power
Press this button, power
on. Press again, power
off.
It will power off automa-
tically within 6~8 mins
if no button was pressed
after power on, or after
the program is finished.
1
Program
Press this button to choose the
program(normal, strong, saree,
wool, + all program with soak)
Press “start/pause” button after
power on, it will work as per fuzzy
program.
3
Start/Hold
Press this button after
power on, it will work as
per the defaulted
program.
Press it while working,
it will stop, and again,
continue.
5
Child Lock
Press ''program + process''
at same time to activate
child lock option.
To remove the child lock
option again press
"program+process"
button at same time.
6
Due to continues R & D, the above graphics may change without any prior notice.
Fuzzy sensing is related to wash process. Machine will sense the cloth load.
Depending on cloth load it will select the water level internally. During the Fuzzy
sensing, Fuzzy LED will wash in Fuzzy mode,glow . The Fuzzy LED means
HOW TO OPERATE MACHINE IN FUZZY MODE ?
1. Put laundry in the machine.
2. Press power button to power on position.
3.
Press START/PAUSE button. Machine will sense cloth load.
4.
Put the detergent & close the lid.
5. Machine will start the operation.
Initially before switching ‘ON’ power if there is some water in the machine, then
machine will directly go to manual mode with medium water level & default
NORMAL Program, then program, or water level can be altered manually.
Press START/PAUSE switch to start operation after selecting it.
About Manual Mode
HOW TO OPERATE MACHINE IN MANUAL MODE
1. Press power switch to ‘ON’ the machine.
2. Select ‘PROGRAM’ depending on laundry type. If required soak can be selected.
3. Select appropriate water level depending on laundry.
4. Put laundry in the machine.
5. Put the detergent.
6. Press START/HOLD switch.
About Machine Operation
i) Machine will complete the processes in following sequence :
ii) When any Program is selected machine is set for standard cycle.
iii) Soak can be selected with wash only. If wash is cancelled soak will be cancelled
iv) Soak selection will be automatically followed by wash.
v) At the end of all selected process the buzzer will sound. & machine will shut off
Automatically (Auto off function).
SOAK
RINSEWASH SPIN
Notes on Using Course
1. Normal Program :
Used for normally soild clothes of daily use.
2. Strong Program :
Used for large sized laundries like curtains, bed sheets or jeans.
3. Saree Program :
Used for lightly soiled clothes like daily wear/under wear grament
or in saree.
4. Wool Program :
Used for heavily decorated clothes, Embrodered clothes woolen.
5. Normal+Soak Program :
Recommended for heavily soiled clothes of daily use.
6. Strong+Soak Program :
Used for heavily soiled jeans or large sized laundries like
curtains, bedsheet etc.
7. Saree + Soak Program :
Saree is generally used to wash Saree and Dhoties.
Recommended for highly soiled decorated clothes or embroidered
clothes etc.
Settings
it keeps glowing till end of wash.
automatically.
About Fuzzy Program
8. Wool + Soak Program :
Page-6
Page-7
Operation of Full Program
SELECTION
PROGRAM
SOAK
(OPTION)
WATER LEVEL
WASH
TIME
RINSE SPIN
RINSE 1
RINSE 2
SPIN 1
SPIN 2**
Normal 23 min.
12 min.
2 min.
Soak
Rinse
2 min.
Soak
Rinse
30 Sec.
Strong 28 min.
15 min.
2 min.
Soak
Rinse
2 min.
Soak
Rinse
30 Sec.
Saree 18 min.
7 min.
2 min.
Soak
Rinse
2 min.
Soak
Rinse
30 Sec.
Wool 13 min.
3 min.
2 min.
Soak
Rinse
30 Sec.
Water filling time depends on tap Water Pressure and selected water level.
Drain time depends on selected water level and number of rinse.
After wash program and water drain there is intermittent spin before rinse.
After first rinse again there is a intermittent spin. Total time in normal
(Soak+Wash+Rinse+Spin) cycle is approx. 51 minutes.
Ex. Dry
28 Minute*
52~56L
40~48L
28~36L
20~24L
52~56L
40~48L
28~36L
20~24L
52~56L
40~48L
52~56L
40~48L
x
x
VT60A12VT55A11
47~52L
37~42L
27~32L
17~22L
47~52L
37~42L
27~32L
17~22L
47~52L
37~42L
47~52L
37~42L
WHAT IS MEMORY BACK UP ?
This facility is useful when there is a power failure while machine is in operation.
Due to memory back-up machine will complete the remaining part of the selected
cycle after power resumes.
HOW TO STOP CYCLE DURING OPERATION ?
If due to some reasons you want to stop the operation midway before completion
of selected cycle then pause the operation by pressing START/HOLD switch &
then press power switch to ‘OFF’ the machine.
THIS IS NOT A PROBLEM
At power ‘ON’ if machine starts any process abruptly, this may be due to stored
memory of previous program which has been stopped intermediately. In this case
to start the machine from beginning proceed as following :
1. Press power to switch ‘OFF’ the machine. This will clear the memory.
2. Again press switch ‘ON’. The machine will start from beginning.
Memory Back-Up
** 4 min SPIN 2 is applicable in Model VT55A11.
7 Min
6 Min
5 Min
4 Min
7 Min
6 Min
5 Min
4 Min
7 Min
6 Min
7 Min
6 Min
* Ex. Dry of 28 Minute is applicable in Model VT60A12.
SOFTENER DISPENSER
Do not pour detergent, bleach, starch etc, in the softener dispenser, otherwise the
machine will operate incorrectly. If you have poured them in the dispenser by mistake,
empty the dispenser by holding it up-side down.
CAUTION ON THE USE OF SOFTENER
1. Do not open lid during spinning operation when softener has been put in the
softener dispenser. The softener would be dispensed incorrectly and be ineffective.
2. Do not leave the machine for an extended time with softener in the dispenser. The
softener could harden, causing misoperation.
3. Pour softener in the dispenser slowly so that it may not spill out.
STANDARD AMOUNT OF SOFTENER
VT60A12
Softener (Approx)
20/24L
18 ml.
28/36L
22 ml.
40/48L
24 ml.
The amount of softener varies depending upon the type of softener. Please
refer to the instructions attached to the Pack/bottle of softener.
52/56L
27 ml.
NOTE
1. Be sure to pour specified amount of softener in dispenser before starting wash.
(Set the softener prior to washing operation.)
2. Softener will be poured into the tub automatically just before the final rinsing.
(When operation starts, softener will be moved from dispenser to balancer.)
How to use Softener
VT55A11
17/22L 27/32L 37/42L 47/52L
Softener Inlet
If it is difficult to put in.
Remove the softener
drawer by pulling it
towards you.
Page-8
Page-9
General Information
Reference chart approx. Weight of garments used daily. A family of two children and their parents.
Wt. of other commonly used clothes
1) Dhotee 215 gms. 2) Woollen Sweater 300 gms. 3) Shawl 375 gms.
4) Pillow Cover 100 gms. 5) Bed sheet 500 gms. 6) Lungi 150 gms.
Put in the detergent and laundry
When using powdered synthetic detergents
Put it in the Detergent Drawer.
[ Please note]
If drawer becomes wet detergent will cling
to it, so please wipe it off with a dry cloth.
Please don’t put in powdered soap. It is difficult to
dissolve and will harden.
When using liquid detergent
Dilute with twice the amount
of water and pour in.
Liquid
detergent
and bleach
inlet
(ON TUB)
Water
DETERGENT AMOUNT
Detergent
Laundry Detergent
(Concen- (Normal)
25g. type/
30 L water
40g. type/
30 L water
Aprox.
58g.
Detergent
47/52L
Powdered
Soap
-
Powder
Liquid
Bleach
Detergent
37/42L
-
Detergent
27/32L
-
Detergent
17/22L
-
58g. 58g. 50g. 50g. 50g. 44g.44g. 44g. 36g. 36g. 36g.
Aprox. Aprox. Aprox. Aprox. Aprox. Aprox. Aprox. Aprox. Aprox. Aprox. Aprox.
Aprox.
37g.
Aprox.
37g.
Aprox.
31g.
Aprox.
31g.
Aprox.
28g.
Aprox.
28g.
Aprox.
23g.
Aprox.
23g.
Powdered
Soap
Powder
Liquid
Bleach
Powdered
Soap
Powder
Liquid
Bleach
Powdered
Soap
Powder
Liquid
Bleach
Liquid Detergent : Dilute with twice the amount of water and pour in.
Liquid Bleach Before beginning the wash, dilute bleach with a good amount of water and pour in. :
Powdered Bleach Put it directly in the washing tub before beginning the wash. :
Please Note Please read and follow closely the directions and warnings for the bleach. :
Please do not put liquid bleach into the washing tub directly.
Warning Liquid soap, like powdered soap is not easily dissolved and can leave :
scum along inside of the washing tub so be sure to rinse thoroughly.
-ntrated)
Level
52/56L 40/48L 28/36L 20/24L
VT55A11
VT60A12
Fault Diagnosis Chart
BEFORE CALLING VIDEOCON SERVICE CENTRE - CHECK THESE POINTS
There may be certain conditions when machine may not function properly & it may give the
Error Signal so check these point against the symptoms.
SYMPTOMS CHECK POINTS
1. Doesn’t run at all.
Check if there is power failure.
Check if the power fuse has blown.
Check if the power plug is plugged in thoroughly.
Check if the power switch has been pressed.
Check if the tub has been filled with the prescribed
quantity of water
(Has the water tap been turned on).
Check if the START/HOLD switch has been pressed.
2. If there is no water supply
Check if you have forgotten to connect the water
hose & to turn on the tap.
Check if the water supply & water hose are frozen.
Check if the water supply has been cut-off.
Check if the connection of water supply hose is clogged
with dirt.
3. When power switch is
pressed ‘ON’ machine starts
any operation abruptly
This may be due to stored Memory of previous program.
Please refer to memory back-up on page 8.
NOTE :
“This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not play with the appliance.”
Specification*
Page-10
Page-11
Usual Faults and Resolving Methods
1. Water is not
supplied after
pressing START/
HOLD switch.
Above set of LEDs starts blinking with
buzzer for 10 seconds. After 10 seconds
buzzer stops but LEDs blink continuously
till machine lid is once opened & closed
once or till water level in tub reaches the
set level. As soon as water level is reached
or lid is open & closed, machine restarts
with its normal operation.
PROGRAM
PROCESS
Have connected
water supply hose &
did you open water
tap ?
Water supply may not
be there.
Water supply hose port
filter may be clogged
with dust. (Refer to
Cleaning of water
supply Hose port on
page 16)
Did you press START/
HOLD switch ?
Ensure proper water
supply.
NORMAL
WASH
RINSE
ERROR
SIGNAL CHECK POINT
SPIN
Lid may be open.
Close the lid, then only
machine will resume
the rest of cycle.
2. Rinse/Spin does
not start though
water is draind
STRONG
WASH
RINSE
SPIN
Above set of LEDs starts blinking with
buzzer for 10 seconds. After 10 seconds
buzzer stops but LEDs blink continue
blinking till the lid is closed. As soon as
lid is closed machine restarts with its
normal operation.
PROGRAM
PROCESS
3. Water is not
drained after
opening of
drain valve
Above set of LEDs starts blinking with
buzzer for 10 seconds, the drain valve is
closed. After 10 seconds buzzer stops but
LEDs continue blinking till machine lid is
once open & closed once. As soon as lid
is closed machine restarts with its normal
operation.
Drain hose may be
abnormal is it lowered ?
Water may be frozen in
it & It may be clogged.
It may be kinked.
Part of drain hose may
be positioned 165 mm or
more higher than floor
level.
Extension hose may be
longer than 3 m.
Hose bore may be too
small.
* Ensure proper drain
system.
WOOL
WASH
RINSE
SPIN
Clothes in the tub may
be gathered on one
side.
Machine may be
4. Midway during
spinning, the
operation
suddenly
SAREE
WASH
RINSE
PROGRAM
PROCESS
wobbling or the floor
changes to
SPIN
may be inclined.
When laundry is
unbalanced during
spin drying automatic
balancing is done by
machine for 2 times by
rinsing & again 3rd
time if imblance
occurs machine gives
the error signal then
rinsing.
Above set of LEDs starts blinking with
buzzer for 10 seconds. After 10 seconds
buzzer stops but LEDs continue blinking
machine will resume the operation, open
PROGRAM
PROCESS
the lid & clothes are evenly distributed then
distribute clothes
lid is closed.
evenly in the tub.
ERROR
SIGNAL
CHECK POINT
Page-12
Usual Faults and Resolving Methods
Page-13
Safety Precaution
Do not use the Washing Machine to wash items other
than Clothes, Blankets, Curtains, Towels and things
alike.
Never disassemble, repair or remodel this
washing machine.
This can cause fire or
irregular action that
results in injury.
Consult your dealer for repair.
Do not damage the power cord and power plug.
(Do not damage, modify, excessively bend, twist, pull,
or bundle the power cord, do not put the power cord
and plug close to a heating appliance, do not put any-
thing heavy on power cord and plug.) If the power
cord cord and plug is damaged, there is a risk of
electric shock, short circuit or fire.
Consult with your dealer about repair of the cord
and plug.
Never touch laundry with your hand
during the spin cycle untill the tub has
completely stopped spinning.
If you touch the laundry, even if the tub
is rotating slowly, there is a danger of
injury if your hand becomes entangled
with the laundry. Pay particular attention
to protecting children from such injury.
Do not install the washing machine
in a humid place such as a bathroom
or in a place exposed to the weather.
There is a risk of electric shock, fire,
breakdowns, or deformation.
When you are cleaning your
washing machine, do not
apply water directly to any part
of the washing machine.
It will cause short circuit and
electric shock.
Children may fall into the tub and
get drowned. Do not leave the
washing machine with lid open
and water remaining inside.
Do not allow your child peer over the
wash tub. Do not place a stool or simi-
lar objects near washing machine.
Do not place flammable
substances near the machine
such as kerosene, benzine,
paint thinner and alcohol. Do
not put clothing with such
substances in the tub.
There is a risk of explosion or fire.
Remove any dust which may accumulate around
the electric cord.
When dust has accumulated on and around the plug,
and the dust gets damp or wet, its insulation becomes
defective and may cause a fire.
Pull out the plug, and wipe off dampness with a dry
clean cloth.
If you are not going to use the washing machine for a
long period of time, pull the power plug out of the socket.
Do not put your hand or foot
under the washing machine
while the machine is
operating.
There is a rotating mechanism
under the machine, so you
could be injured.
Always pull the power plug out
of the socket before doing any
cleaning or maintenance of
the washing machine.
Otherwise, you may suffer
electric shock or injury.
Do not use a plug socket and wiring equipment
for more than their capacity.
If you use socket or wiring for more than its rated
capacity by connecting multiple appliances, it can
cause fire due to overtheating.
Make sure to push the plug
completely into the socket.
If the plug is not completely pushed into
the socket, this will cause electric shock
and fire due to overheating.
Never use a damaged power plug
or cord
Do not pull out or push in the power
plug with a wet hand.
It will cause electric shock.
Page-14
Do not place any burning
object including burning candles
or cigarettes, near the washing
machine.
There is a danger of fire or
deformation.
Do not use water hotter than
50
0
C for wash water.
The plastic parts will become
deformed resulting in electric
shock or electricity leakage.
Do not climb up or put anyting
heavy on the top of the
machine.
You could be injured due to
deformation or breakage of the
washing machine.
Always check the hose connection by turning on the
water tap before washing.
If the fixing screws are loose, it causes water leakage
that could cause unespected damage.
Never disconnect by pulling the
cord. Hold its plug when you pull
it out.
There is danger of an electric
shock or short circuit which may
cause a fire.
Do not wash and spin waterproof sheets
and garments
(Example) Raincoats, outfits (coats/
jackets) and pants for fishing and
skiing, etc.
The items could be damaged or you
could be injured due to irregular
vibration during the spin cycle.
Install the washing machine on a sturdy floor of which
maximum permissible inclination is two degrees.
If the machine is installed on carpet, make sure
that the carpet does not block any openings.
Fully Automatic Washing Machine should not
be installed on TROLLY.
Insure three core power plug seat must have
ground connection.
Safety Precaution
Large and bulky
clothing
If you gently press
down on the clothing
while the tub is filling
such that it completely
absorbs the water, the
laundry will
be balanced.
When there is lint or
balls of wool
Turn it inside out.
Clothing which has long
cords or clasps attached
Tie the cords on
aprons,pillow covers and
the like and fasten clasps.
Clothing which is too delicate
to wash even in the delicate
and hand wash cycles.
Put clothing with lace attached,
lingerie, nylon stockings,
chemical fibre transparent
fabrics etc.
in a store-bought
washing net.
Tips for not damaging clothing
1. Put in soap and laundry and
run WASH and DRAIN cycles.
3. Take out the laundry when draining
rinse water use spin-dry only.
2. Stop the WASH cycle before the final
spin dry leaving the laundry as is in
the water. (Stop drainage)
Preventing Wrinkles
Page-15
1. Remove it.
Pull off the filter frame.
Cleaning out lint filter
Maintaining the
machine
2. Clean out the lint. Turn
the filter Inside out and
wash it out in water.
3. Put it back on. Return
the filter to its original state
and holding the filter frame,
reinsert it securely.
Wipe it regularly with a
soft cloth.
When it is unusually
dirty, wipe it with a
cloth which has been
soaked in a neutral
soap or soapy water.
Please do not put water on
it directly or wipe it with
thinner, cleanser, kerosene,
benzine, alcohol etc.
If you use a chemical
swab, please follow the
directions closely.
Cleaning the water
supply hose and fitting
Detach the water
supply hose periodically
and clean out filter
residue with a brush.
If you simply detach the
water supply hose water will
splash out, so follow this
procedure before detaching it.
1. Close the water tap.
2. Press ON the power
swtich
3. Push the START/HOLD
switch
4. Press OFF power
switch after few seconds
5. Loosen and remove the
water supply hose nut.
Do not use machine
with damaged/without
Lint Filter
Maintenance
Page-16
Not to Forget
Don’t get water on the control panel
There is risk of electric
shock or breakdown.
Don’t put in too much detergent !
If too much detergent is used, soap
suds will be difficult to get
rid of and rinsing will be
insufficient.
When articles are used as a cover
Refrain from using chlorine
vinyl covers. They will scar
the Iacquer and resin
surfaces.
If you use a vinyl
chloride cover, place
a cloth on th machine
before putting the
cover on.
After finishing don’t forget.....
Please shut off the tap. If you are not going to
use the machine for a long period of time,
please remove the plug.
Please don’t let water
sit for a long time.
Handling and inspection of the electric
cord and plug
When pulling out the cord
and plug, hold from the
plug and pull.
Please be sure to close the lid
If the lid isn’t closed, the spin function won’t
occur and will be displayed.
Don’t put too much laundry in !
Please fold bulky clothing and put it in such a
way that it won’t stick out.
Don’t wash water-repellent
clothing and sheets.
Condensation
When the air temperature
is high but the water temperature
is low, condensation will build
up on the outside of the
washing tub and the floor
will become wet.
Page-17
Warranty terms and conditions
FILL AND DESPATCH WARRANTY CARD ELSE THE WARRANTY VOIDS
1. This warranty is confined to the original products of the only.manufacturer
2. The or their authorised service manufacturer Agent / will repair / replace all parts failing due
to faulty material or defective workmanship pertaining to the above Washing Machine.
3. Only the or its authorised Service manufacturer Agent / can service/repair/attend to install/
reinstall the washing Machine. The list of ’s serivce centre is as printed overleaf.Manufacturer
4. If the machine is not repairable at the place of its installation then the decision of
technician to call back the machine to Service Centre for repairs shall be final. In such
cases it is the responsibility of Purchaser to bring the machine to the Service Centre.
5. For the units installed beyond the municipal limits of the jurisdiction of the authorised
service a ’Manufacturer Manufacturers authorized service station or ’s dealers as well as
expenses incurred in connection with deputing of service personnel/technicians towards
to and fro travel conveyance with deputing of service incidentials etc. will be borne by
the customer.
6.
Any change of location of the unit and / or change of ownership has to be done in
consultation with the or its authorised service agent so that the warrantyManufacturer
obligation for the remaining part of the warranty could be transferred to the new owners
or the original purchaser but at the new location. The unit so transferred will be inspected
by the or its service agent at the cost inspection charges.Manufacturer
7. Any damage caused during shifting will be repaired on chargeable basis. In the event of
repair / replacement of any part/s of the set, this warranty will thereafter, continue and
remain in force only for the unexpired period as per the warranty card issued at the time
of purchase of the set. Moreover, the time taken for repair and in transit, whether under
the warranty or otherwise, shall not be excluded from the warranty period.
8. This warranty will continue to be in force for the term herein specified, irrespective of
what replaced may be provided under it, and such replacement shall not attract any
fresh warranty unless specified.
9. The warranty extended herein is in lieu of all implied conditions and warranties under the
law and is confined to the repair or replacement of defective parts and does not cover
any consequential or resulting liability, damage or loss arising from such defects.
Furthermore, the warranty in no case, shall extend to the payment or any monetary
consideration whatsoever of the replacement or return of the Washing Machine as a
whole.
10. The defective spare part/s shall be the sole property of and will be collectedmanufacturer
by the Authorised Service Centre / Franchisee.
11. It shall be the discretion of the to replace the required part with suitable andmanufacturer
currently available part/s. The may also use the substitute part for defective part.manufacturer
Manufacturer of this VIDEOCON Brand Washing Machine undertake that the product is warranted
against manufacturing defects for a period of date of purchase,24 months, commencing from the
the manufacturer will repair or replace free parts of the Washing Machineof charge any part or
sole discretion, that the defect/s material or workmanship only.is/are due to faulty
The warranty will be governed by the following clauses :
except Top Lids, Inlet/Drain Hose and the company be fully satisfied, in itslint Filter, should
Page-18
Warranty terms and conditions
15km. STONE, AURANGABAD-PAITHAN ROAD,
VILLAGE CHITEGAON, TALUKA PAITHAN,
AURANGABAD - 431 105,
MAHARASHTRA, INDIA.
PHONE No. - 02431 - 329271,329783
TEKCARE INDIA PRIVATE LIMITED.,
For any doubts or clarifications please contact us on-
12.
The warranty does not cover any accessories external to the system or supplied by dealer .
13. The ’s obligation under this warranty shall be limited to repairing or providingmanufacturer
replacement of parts, which are found to be defective within warranty period.
14. Any defects in electrical installation on fittings outside Washing Machine shall have to
be rectified by the purchaser only.
15. The shall not be liable for any delay in rectifying the machine, in the event ofmanufacturer
non-availability of components and shall in no way be responsible for any losses, direct
or indirect, arising out of the delay, if any.
16.
If the machine is inspected by the authorized service center during warranty period
and product is found free from any sort of damage/defect, Applicable visiting charges
17. Warranty shall stand ceased / cancelled if the machine is used for any type of
commercial purpose.
18. The is not responsible for any breakage or non - performance or delay inmanufacturer
providing service due to strike, industrial/labour dispute, fire, accident, damage,
restriction imposed by Government, Act of God, riot, war, etc. which are beyond the
control of the .manufacturer
19. The warranty is issued subject to the jurisdiction of Aurangabad Court of law.
THIS WARRANTY IS NOT APPLICABLE IN ANY OF THE FOLLOWING CASES
1. The warranty card is not duly filled and mailed back to the service centre for
registration by the purchaser, within 10 days of purchase.
2.
The completed Warranty card is not presented to the technician at the time of repair.manufacturer
3. The machine is not used according to the instruction given in owner’s guide.
4. Defects caused by improper use as determined by the personnel.manufacturer
5. Any repair work/installation is carried out by the person other than Videocon service
centre/service agent.
6. Site (premises where the product is kept) conditions that do not conform to the
recommended operating conditions of the machine.
7. The serial number is deleted, defaced or altered.
8. If the electrical power supply voltages, are not within the stipulated norms.
9. Any defects arising out of lightning, abnormal voltage, fire, accident, any acts of God
or other circumstances beyond the control of the while the machine is in transitmanufacturer
or otherwise.
10. Defects caused by household pets, Rats, Cockroaches or any other animals or insects.
will be payable by customer.
20. If any colored internal or external components are replaced there will be commitment to
ensure that shades match with the original or other components. The replaced shades,
patterns, tints may vary from the customer's unit due to continuous usage of unit. Any
matching components changed at customer's request will be on chargeable basis except
the component which are actually needed.
E MAIL : customerc[email protected]
Web : www.servicedelight.com
CSO AURANGABAD COPY
Note : The after sale service shall be subject to the production of this card at the time of each servicing, either at
the place of the customer or at any service center. In absence of this card, the company shall not be liable
to provide after sale service as per the warranty norms.
This card stands null and void if the Service Center copy of Warranty Card is not dispatched within 10
days of date of purchase (DOP) and duly signed by Authorized Dealer on date of purchase.
Dealer sign & seal Customer sign
Customer Name :
Customer Address :
Tel No. :
Dealer Name :
Dealer Address :
Tel No. :
Model No. :
DOP :
I accept the terms and conditions of warranty.
Dealer Bill Date :
Bill No. :
Set Serial No. :
Service Registration at -
SERVICE CENTER COPY
Dealer sign & seal
Customer sign
Customer N
ame
:
Customer Address :
Tel No. :
Dealer Name :
Dealer Address
:
Tel No. :
Model No. :
DOP :
I accept the
terms and conditions of warranty.
Dealer Bill Date :
Bill No. :
Set Serial No. :
Service Registration at -
CUSTOMER COPY
Dealer sign & seal Customer sign
Customer Name :
Customer Address :
Tel No. :
Dealer Name :
Dealer Address :
Tel No. :
Model No. :
DOP :
I accept the terms and conditions of warranty.
Dealer Bill Date :
Bill No. :
Set
Serial No. :
Service Registration at -
CUT HERE
CUT HERE
/