Danfoss NovoCon® S Digital & Hybrid - High Accuracy Actuator Operating instructions

Danfoss
Brand
Danfoss
Model
NovoCon® S Digital & Hybrid - High Accuracy Actuator
Category
Motorcycle Accessories
Type
Operating instructions

Danfoss NovoCon® S Digital & Hybrid - High Accuracy Actuator

The Danfoss NovoCon® S Digital & Hybrid - High Accuracy Actuator is a versatile and powerful device designed to provide precise control over a wide range of applications. With its IP54 rating, it is suitable for use in harsh environments, making it an ideal choice for industrial and commercial settings.

The NovoCon® S Actuator offers both digital and hybrid control options, allowing you to choose the best mode for your specific needs. The digital control mode provides high precision and accuracy, while the hybrid mode combines digital and analog control for optimal performance.

Danfoss NovoCon® S Digital & Hybrid - High Accuracy Actuator

The Danfoss NovoCon® S Digital & Hybrid - High Accuracy Actuator is a versatile and powerful device designed to provide precise control over a wide range of applications. With its IP54 rating, it is suitable for use in harsh environments, making it an ideal choice for industrial and commercial settings.

The NovoCon® S Actuator offers both digital and hybrid control options, allowing you to choose the best mode for your specific needs. The digital control mode provides high precision and accuracy, while the hybrid mode combines digital and analog control for optimal performance.

NovoCon® S Digital & Hybrid - High Accuracy Actuator
VI.HU.H3.02 | 1© Danfoss | 2017.05
Operating Guide
❶
IP40
IP54
IP54
IP54
❷
❸
❹
①
②
①
③
②
*VIHUH302*
❺
❼
❻
Calibration:
Press button ① until two
LED’s are turned on
DIP switch: ②
Manual override:
Adjust wheel ③
Serial number can be removed
from the NovoCon® S and added
to installation drawing.
Device Object
Instance Number
H200 V01
281624
0030471
H200 V01
281624
0030471
H200 V01
281624
0030471
MADE IN SLOVENIA
NovoCon
S Digital & Hybrid
003Z8502
Actuator for AB-QM DN10-32
Control signal: BACnet MS/TP, Modbus RTU, 0-10V, 0-20mA
®
6430 Nordborg, Denmark
Power: 24VAC/DC, 50/60 HZ
Force: 90N. Stroke: 7 mm. Speed: 3-24s/mm
Consumption: 3.9VA running. Standby 0.9W
IP54/40, -10T55
III
Danf
oss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products
already on order pro
vided that such alterations can be made without subsequential changes being necessary eady agreed.
All trademarks in this material are property of the respec
tive companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
73694010 / VI.HU.H3.022 | © Danfoss | DHS-SRMT/SI | 2017.05
NovoCon® S Digital & Hybrid - High Accuracy Actuator
Red
Black
Green
White/
green
Common ground for power and bus signal wire
´+´ non-inverting signal wire
´−´ inverting signal wire
Red
Black
Grey
Blue
Power
Power ground
Analog input
Analog input ground
Digital port
Analog port or
voltage booster
Digital port
NovoCon® S
BV:0 / 32784
Digital control (default)
or
Analog control
MSV:3 / 32802
Select Valve Type
(defau lt AB-QM DN 15)
AV:0 / 32768
Design Flow Rate
BACnet object / Modbus register
❾ ❿
⓫
DIP Switch
DIP Switches 1 to 7 are used to assign the MAC address manually. Default
setting is Auto MAC addressing for BACnet MS/TP and DIP Switches
for Modbus RTU.
For termination of last unit on the field bus, turn DIP Switch 8 ON.
Dip switch 9 is not used.
Dip switch 10 is used to select between BACnet MS/TP (OFF=Default)
and Modbus RTU (ON).
When the protocol is changed on DIP Switch 10, a power cycle is required.
Power
NovoCon® digital cable
NovoCon® analog cable
❽
Presettings
1 2 3 4 5 6 7 8 9 10
ON
OFF
Safety Note
To avoid injury and damage to persons and devices, it is
absolutely necessary these instructions are carefully read
and observed prior to assembly and commissioning.
Necessary assembly, start-up, and maintenance work
must be performed only by qualified, trained and authorised personnel.
Switch off the power line before wiring the actuator.
Disposal instruction
Always follow the local disposal regulations.
Common ground shall be
used for all devices on the
same network.
Safety Note
Connect via safety isolating transformer.
Galvanic separations shall be provided for segments
crossing buildings.
Safety Note
If the NovoCon® S network is supplied with two or more AC
pow er booster s, caution m ust be obser ved whe n disconnec ting
one of the transformers from the high voltage power line. As the
NovoCons are connected in a daisy chain, there may be high
voltage on the primary side of the disconnected power supply. Disconnect
always both the primary and secondary side of the transformer.
  • Page 1 1
  • Page 2 2

Danfoss NovoCon® S Digital & Hybrid - High Accuracy Actuator Operating instructions

Danfoss
Brand
Danfoss
Model
NovoCon® S Digital & Hybrid - High Accuracy Actuator
Category
Motorcycle Accessories
Type
Operating instructions

Danfoss NovoCon® S Digital & Hybrid - High Accuracy Actuator

The Danfoss NovoCon® S Digital & Hybrid - High Accuracy Actuator is a versatile and powerful device designed to provide precise control over a wide range of applications. With its IP54 rating, it is suitable for use in harsh environments, making it an ideal choice for industrial and commercial settings.

The NovoCon® S Actuator offers both digital and hybrid control options, allowing you to choose the best mode for your specific needs. The digital control mode provides high precision and accuracy, while the hybrid mode combines digital and analog control for optimal performance.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers