Bosch RH328VC HDC100 User manual

IMPORTANT: IMPORTANT : IMPORTANTE:

Read Before Using Lire avant usage Leer antes de usar

For English Version Version française Versión en español

See page 2 Voir page 14 Ver la página 26

Operating/Safety Instructions

Consignes de fonctionnement/sécurité

Instrucciones de funcionamiento y seguridad

1-877-BOSCH99 (1-877-267-2499) www.boschtools.com

Call Toll Free for

Consumer Information

& Service Locations

Pour obtenir des informations

et les adresses de nos centres

de service après-vente,

appelez ce numéro gratuit

Llame gratis para

obtener información

para el consumidor y

ubicaciones de servicio

RH328VC

RH328VCQ

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 1

-2-

$692(9,(:(-,;@

,,7>692(9,(*3,(5(5+>,3330;Cluttered

or dark areas invite accidents.

6 56; 67,9(;, 76>,9 ;663: 05 ,?736:0=,

(;46:7/,9,: :<*/ (: 05 ;/, 79,:,5*, 6-

-3(44()3, 308<0+: .(:,: 69 +<:; Power

tools create sparks which may ignite the dust

or fumes.

,,7 */03+9,5 (5+)@:;(5+,9: (>(@>/03,

67,9(;05. ( 76>,9 ;663 Distractions can

cause you to lose control.

3,*;90*(3:(-,;@

6>,9 ;663 73<.: 4<:; 4(;*/ ;/, 6<;3,;

,=,946+0-@;/,73<.05(5@>(@656;

<:, (5@ (+(7;,9 73<.: >0;/ ,(9;/,+

.96<5+,+ 76>,9 ;663: Unmodified plugs

and matching outlets will reduce risk of electric

shock.

=60+)6+@*65;(*;>0;/,(9;/,+69.96<5+,+

:<9-(*,: :<*/(:707,: 9(+0(;69:9(5.,:

(5+9,-90.,9(;69:There is an increased risk

of electric shock if your body is earthed or

grounded.

656; ,?76:, 76>,9;663: ;69(05 69>,;

*65+0;065:Water entering a power tool will

increase the risk of electric shock.

656;()<:,;/,*69+,=,9<:,;/,*69+

-69*(99@05.7<3305.69<573<..05.;/,76>,9

;663,,7 *69+(>(@-964/,(;603:/(97

,+.,:6946=05.7(9;:Damaged or entangled

cords increase the risk of electric shock.

$/,5 67,9(;05. ( 76>,9 ;663 6<;+669:

<:,(5,?;,5:065*69+:<0;()3,-696<;+669

<:, Use of a cord suitable for outdoor use

reduces the risk of electric shock.

-67,9(;05.(76>,9;66305(+(4736*(;065

0:<5(=60+()3,<:,(96<5+(<3;09*<0;

5;,99<7;,9796;,*;,+:<773@Use of

an GFCI reduces the risk of electric shock.

,9:65(3:(-,;@

;(@(3,9;>(;*/ >/(; @6< (9, +605.(5+

<:, *64465 :,5:, >/,5 67,9(;05. (

76>,9;663656;<:,(76>,9;663>/03,

@6<(9,;09,+69<5+,9;/,05-3<,5*,6-+9<.:

(3*6/63694,+0*(;065A moment of inattention

while operating power tools may result in

serious personal injury.

":,7,9:65(3796;,*;0=,,8<074,5;3>(@:

>,(9 ,@, 796;,*;065 Protective equipment

such as dust mask, non-skid safety shoes, hard

hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

9,=,5;<505;,5;065(3:;(9;05.5:<9,;/,

:>0;*/ 0: 05 ;/, 6--76:0;065 ),-69,

*655,*;05.;676>,9:6<9*,(5+69)(;;,9@

7(*2 70*205.<7 69 *(99@05. ;/, ;663

Carrying power tools with your finger on the

switch or energizing power tools that have the

switch on invites accidents.

,46=,(5@(+1<:;05.2,@69>9,5*/),-69,

;<9505.;/,76>,9;66365A wrench or a key

left attached to a rotating part of the power tool

may result in personal injury.

656;6=,99,(*/,,77967,9-66;05.(5+

)(3(5*, (; (33 ;04,: This enables better

control of the power tool in unexpected

situations.

9,::7967,93@656;>,(9366:,*36;/05.

69 1,>,39@ ,,7 @6<9 /(09 *36;/05. (5+

.36=,: (>(@ -964 46=05. 7(9;: Loose

clothes, jewelry or long hair can be caught in

moving parts.

-+,=0*,:(9,796=0+,+ -69;/, *655,*;065

6-+<:;,?;9(*;065 (5+*633,*;065 -(*030;0,:

,5:<9,;/,:,(9,*655,*;,+ (5+ 7967,93@

<:,+Use of dust collection can reduce dust-

related hazards.

6>,9;663<:,(5+*(9,

656;-69*,;/,76>,9;663":,;/,*699,*;

76>,9 ;663-69@6<9(7730*(;065The correct

power tool will do the job better and safer at

the rate for which it was designed.

656;<:,;/,76>,9;6630-;/,:>0;*/+6,:

56; ;<95 0; 65 (5+ 6-- Any power tool that

cannot be controlled with the switch is

dangerous and must be repaired.

,(+(33:(-,;@>(9505.:(5+(3305:;9<*;065:Failure to follow the warnings

and instructions may result in electric shock, fire and/or serious injury.

#$  !"! "!"

The term “power tool” in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

!

WARNING

,5,9(36>,9!663 (-,;@$(9505.:

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 2

-3-

6;(9@(44,9 (-,;@<3,:

0:*655,*;;/,73<.-964;/,76>,9:6<9*,

(5+69;/,)(;;,9@7(*2-964;/,76>,9;663

),-69, 4(205. (5@(+1<:;4,5;:*/(5.05.

(**,::690,: 69:;6905.76>,9 ;663: Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

;69,0+3,76>,9 ;663:6<;6-;/, 9,(*/6-

*/03+9,5(5++656;(336>7,9:65:<5-(4030(9

>0;/;/,76>,9;66369;/,:,05:;9<*;065:;6

67,9(;, ;/, 76>,9 ;663 Power tools are

dangerous in the hands of untrained users.

(05;(0576>,9;663:/,*2-6940:(30.54,5;

69 )05+05. 6- 46=05. 7(9;: )9,(2(., 6-

7(9;: (5+ (5@ 6;/,9 *65+0;065 ;/(; 4(@

(--,*;;/,76>,9;663C:67,9(;065-+(4(.,+

/(=, ;/, 76>,9 ;663 9,7(09,+ ),-69, <:,

Many accidents are caused by poorly

maintained power tools.

,,7*<;;05.;663::/(97(5+*3,(5Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

":, ;/,76>,9;663(**,::690,:(5+;663

)0;:,;*05(**69+(5*,>0;/;/,:,05:;9<*;065:

;(205.05;6(**6<5;;/,>69205.*65+0;065:

(5+ ;/,>692;6),7,9-694,+ Use of the

power tool for operations different from those

intended could result in a hazardous situation.

,9=0*,

(=,@6<976>,9;663:,9=0*,+)@(8<(30-0,+

9,7(09 7,9:65 <:05. 653@ 0+,5;0*(3

9,73(*,4,5;7(9;:This will ensure that the

safety of the power tool is maintained.

$,(9,(9 796;,*;69:>/,5047(*;+903305.

Exposure to noise can cause hearing loss.

":,(<?030(9@/(5+3,:0-:<7730,+>0;/;/,

;663 Loss of control can cause personal injury.

63+ 76>,9 ;663 )@ 05:<3(;,+ .907705.

:<9-(*,: >/,5 7,9-69405. (5 67,9(;065

>/,9,;/,*<;;05. (**,::69@4(@*65;(*;

/0++,5 >0905.690;: 6>5 *69+ Cutting

accessory contacting a "live" wire may make

exposed metal parts of the power tool "live"

and could give the operator an electric shock.

":, *3(47: 69 (56;/,9 79(*;0*(3 >(@ ;6

:,*<9, (5+ :<7769; ;/, >69270,*, ;6 (

:;()3,73(;-694Holding the work by hand

or against your body leaves it unstable and

may lead to loss of control.

":, (4,;(3 +,;,*;69 ;6+,;,9405,0-;/,9,

(9,.(:69>(;,9707,:/0++,505 ;/,>692

(9,( 69 *(33 ;/, 36*(3 <;030;@ *647(5@ -69

(::0:;(5*,),-69,),.05505.;/,67,9(;065

Striking or cutting into a gas line will result in

explosion. Water entering an electrical device

may cause electrocution.

3>(@: <:,;/, :0+,/(5+3,-69 4(?04<4

*65;9636=,9 ;698<, 9,(*;0656920*2)(*2

,=,9(;;,47;;667,9(;,;/0:;663>0;/65,

/(5+ The slip clutch engages if you firmly

control the tool during a torque reaction or

kickback.

3>(@: >,(9 :(-,;@ .6..3,: 69 ,@,

796;,*;065>/,5<:05.;/0:;663":,(+<:;

4(:2699,:709(;69-69(7730*(;065:>/0*/

.,5,9(;, +<:; Safety goggles or eye

protection will help deflect fragments of the

material that may be thrown toward your face

and eyes. Dust generated or gases released

from the material you are cutting (i.e. asbestos

insulated pipes, radon) may cause respiratory

difficulties.

":, ;/0*2 *<:/065,+ .36=,: (5+ 3040; ;/,

,?76:<9, ;04, )@ ;(205. -9,8<,5; 9,:;

7,906+: Vibration caused by hammer-drill

action may be harmful to your hands and

arms.

6:0;065 ;/,*69+ *3,(96-96;(;05.)0; 6

56; >9(7 ;/, *69+ (96<5+ @6<9 (94 69

>90:; If cord becomes entangled with the

spinning bit it could entrap you causing

serious personal injury.

6:0;065 @6<9:,3- ;6 (=60+ ),05. *(<./;

),;>,,5;/,;66369:0+,/(5+3,(5+>(33:

69 76:;:  Should the bit become bound or

jammed in the work, the reaction torque of the

tool could crush your hand or leg.

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 3

-4-

GFCI and personal protection devices like

electrician’s rubber gloves and footwear will

further enhance your personal safety.

6 56; <:,653@9(;,+;663: >0;/( 

76>,9 :<773@ While the tool may appear to

work, the electrical components of the AC

rated tool are likely to fail and create a hazard

to the operator.

,,7/(5+3,:+9@*3,(5(5+-9,,-964603

(5+ .9,(:,Slippery hands cannot safely

control the power tool.

":,*3(47:696;/,979(*;0*(3>(@;6:,*<9,

(5+:<7769;;/, >69270,*, ;6 (:;()3,

73(;-694Holding the work by hand or against

your body is unstable and may lead to loss of

control.

,=,367( 7,906+0*4(05;,5(5*,:*/,+<3,

-69 @6<9 ;663 $/,5 *3,(505. ( ;663 ),

*(9,-<356;;6 +0:(::,4)3,(5@ 769;0656-

;/, ;663 :05*, 05;,95(3 >09,: 4(@ ),

40:73(*,+69705*/,+69:(-,;@.<(9+9,;<95

:7905.: 4(@ ), 047967,93@ 46<5;,+

Certain cleaning agents such as gasoline,

carbon tetrachloride, ammonia, etc. may

damage plastic parts.

Risk of injury to user. The power cord must only

be serviced by a Bosch Factory Service Center

or Autho rized Bosch Service Station.

64,+<:;*9,(;,+)@76>,9

:(5+05.:(>05..905+05.

+903305. (5+ 6;/,9 *65:;9<*;065 (*;0=0;0,:

*65;(05:*/,40*(3:256>5;6*(<:,*(5*,9

)09;/ +,-,*;: 69 6;/,9 9,796+<*;0=, /(94

64,,?(473,:6-;/,:,*/,40*(3:(9,

• Lead from lead-based paints,

• Crystalline silica from bricks and cement and

other masonry products, and

• Arsenic and chromium from chemically-

treated lumber.

Your risk from these exposures varies,

depending on how often you do this type of

work. To reduce your exposure to these

chemicals: work in a well ventilated area, and

work with approved safety equipment, such as

those dust masks that are specially designed

to filter out microscopic particles.

++0;065(3 (-,;@$(9505.:

!

WARNING

656;:;902,;/,)0;>0;/(/(5+/,3+/(44,9

69 :3,+., /(44,9 >/,5 (;;,47;05. ;6

+0:36+.,()6<5+691(44,+)0;Fragments

of metal from the bit could dislodge and strike

you or bystanders.

,=,9 73(*, ;/,;663 +6>5<5;03;/, )0;69

(**,::69@/(=,*64,;6(*6473,;,:;67

6 56; <:, +<33 69 +(4(.,+ )0;: (5+

(**,::690,: Dull or damaged bits have a

greater tendency to bind in the workpiece.

$/,59,46=05.;/,)0;-964;/,;663(=60+

*65;(*;>0;/:205(5+ <:,7967,9796;,*;0=,

.36=,:>/,5.9(:705.;/,)0;69(**,::69@

Accessories may be hot after prolonged use.

656;9<5;/,;663>/03,*(99@05.0;(;@6<9

:0+, The spinning drill bit may become

entangled with clothing and injury may result.

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 4

-5-

!! Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and safer.

@4)63 (4, ,:0.5(;065?73(5(;065

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Diameter Size of drill bits, grinding wheels, etc.

n

0

No load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

.../min Revolutions or reciprocation Revolutions, strokes, surface speed,

per minute orbits etc. per minute

0 Off position Zero speed, zero torque...

1, 2, 3, ... Selector settings Speed, torque or position settings.

I, II, III, Higher number means greater speed

Infinitely variable selector with off Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II construction Designates Double Insulated

Construction tools.

Earthing terminal Grounding terminal

Warning symbol Alerts user to warning messages

Li-ion RBRC seal Designates Li-ion battery recycling

program

Ni-Cad RBRC seal Designates Ni-Cad battery recycling

program

Read manual symbol Alerts user to read manual

Wear eye protection symbol Alerts user to wear eye protection

@4)63:

0

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 5

-6-

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this tool is listed by the Canadian Standards

Association.

This symbol designates that this tool is listed by the Canadian Standards

Association, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

@4)63:*65;05<,+

!! Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and safer.

This symbol designates that this tool is recognized by Underwriters Laboratories.

This symbol designates that this tool is listed by Underwriters Laboratories,

to United States and Canadian Standards.

Conforms to

UL Standard 60745-1

UL Standard 60745-2-6

Certified to

CAN/CSA Standard C22.2 No. 60745-1

CAN/CSA Standard C22.2 No. 60745-2-6

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 6

-7-

<5*;065(3,:*907;065(5+ 7,*0-0*(;065:

0:*655,*; ;/, 73<. -964 ;/, 76>,9 :6<9*, ),-69, 4(205. (5@

(::,4)3@(+1<:;4,5;:69*/(5.05.(**,::690,: Such preventive safety

measures reduce the risk of starting the tool accidentally.

!

WARNING

Model number RH328VC & RH328VCQ

Shank style SDS-plus

B

Maximum Capacities:

Carbide tipped bits 1-1/8"

Thin wall core bits 3-1/4"

6;(9@(44,9

! For tool specifications refer to the nameplate on your tool.

DEPTH GAUGE RELEASE BUTTON

LOCKING

RING

LOCKING SLEEVE

SDS-plus

B

CHUCK

AUXILIARY

HANDLE

HAND GRIP

VIBRATION DAMPER

HANDLE / HAMMER MECHANISM

VARIABLE

SPEED

TRIGGER

SWITCH

FORWARD /REVERSE

SWITCH

DRILL/HAMMER

DRILL

SELECTION DIAL

FIG. 1

DEPTH GAUGE

DUST

SHIELD

3-JAW CHUCK

(Not included, available

as accessory)

VENTILATION

OPENINGS

RELEASE BUTTON SELECTION DIAL

SDS-plus

®

QUICK CHANGE CHUCK

(Model RH328VCQ only)

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 7

-8-

0:*655,*; ;/, 73<. -964

;/, 76>,9 :6<9*, ),-69,

4(205. (5@ (::,4)3@ (+1<:;4,5;:69

*/(5.05. (**,::690,: Such preventive

safety measures reduce the risk of starting the

tool accidentally.

 !  73<:

B

 

Clean the insert shank end of the accessory to

remove any debris, then lightly grease with a

light oil or lubricant.

Insert accessory into the chuck through the

dust shield, while twisting and pushing inward

until it locks automatically into place. Pull

outward on the accessory to be certain it is

locked into the chuck (Fig. 2).

! The high efficiency available from the

rotary hammers can only be obtained if sharp

and undamaged accessories are used. The

"cost" to maintain sharp and undamaged

accessories is more than offset by the "time

saved" in operating the tool with sharp

accessories.

#  73<:

B

 

Accessories may be hot after

use. Avoid contact with skin

and use proper protective gloves or cloth to

remove.

To remove an accessory, pull locking sleeve

backward and pull bit forward. All accessories

should be wiped clean after removing (Fig. 3).

6;,when replacing original SDS-plus quick

change chuck, always make sure the replace-

ment chuck has the proper number of

identification grooves.

#!  73<:

B

""

6+,3#653@

Grasp the locking ring of the SDS-plus quick

change chuck and pull forcefully in direction of

arrow  while pulling chuck in direction of

arrow  and remove from tool (Fig. 4).

!!  73<:

B

""

6+,3#653@

Before attaching the chuck apply a light coat of

grease to end of the shank.

Grasp the SDS-plus chuck firmly with your

hand and push it onto the tool with a twisting

motion until you hear it lock into place (Fig. 5).

A

B

FIG. 2

FIG. 3

FIG. 4

FIG. 5

LOCKING

RING

DUST SHIELD

LOCKING SLEEVE

!

WARNING

::,4)3@

SDS-plus

B

QUICK

CHANGE CHUCK

!

WARNING

SDS-plus

B

CHUCK

IDENTIFICATION

GROOVES

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 8

-9-

 ! 

$"

6+,3#653@

6;05*3<+,+(=(03()3,(:(**,::69@

Hold chuck collar with one hand and rotate

chuck sleeve in direction of arrow with the

other hand until the jaws are open (Fig. 7).

For small bits, open jaws enough to insert the

bit up to the flutes. For large bits, insert the bit

as far as it will go.

Insert bit, hold the chuck collar with one hand

and rotate chuck sleeve in direction of arrow

with the other hand until it latches. Then clamp

the accessory by continuing to turn the chuck

sleeve forcefully in direction of arrow until you

hear a ratcheting sound (Fig. 8).

6;, If after opening the chuck completely

you hear a ratcheting sound when closing,

simply open it a quarter turn and then resume

closing the chuck. The ratcheting sound will

stop.

# 

$"

To remove a accessory, hold chuck collar with

one hand and rotate chuck sleeve in direction

of arrow with the other hand until the

accessory can be removed (Fig. 8).

I

FIG. 7

FIG. 8

CHUCK

COLLAR

CHUCK

SLEEVE

CHUCK

COLLAR

CHUCK

SLEEVE

Do not carry the tool by the

chuck. Tool may unexpectedly

fall if the chuck is not fully engaged.

The SDS-plus chuck can easily be exchanged

for the 3-jaw chuck.

Hammer drilling and chiseling are only

possible when using the SDS-plus chuck with

SDS-plus shank accessories.

The 3-jaw chuck converts your tool for use with

a variety of straight shank bits for drilling and

driving.

#!  73<:

B

"

6+,3#653@

Grasp the locking ring of the SDS-plus chuck

and pull forcefully in direction of arrow and

remove from tool (Fig. 4).

!!!$"

6+,3#653@

6;05*3<+,+(=(03()3,(:(**,::69@

Grasp the 3-jaw chuck firmly with your hand

and push it onto the tool with a twisting motion

until you hear it lock into place (Fig. 6).

Pull outward on the chuck to be certain it is

locked into the tool.

!

WARNING

FIG. 6

3-JAW

CHUCK

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 9

-10-

!"

Your drilling depth can be pre-set and/or

repeated by using the depth gauge.

Setting depth: After the auxiliary handle is

installed, make sure the accessory has been

fully inserted into the tool holder before

setting the depth gauge (Fig. 10).

To adjust depth, push the depth gauge

release button, slide the depth gauge to

desired depth and release pressure on

button to lock the depth gauge in place.

"%&

The tool must be supported with the auxiliary

handle, which can be swiveled 360˚. To

reposition and/or swivel the handle, loosen

the hand grip, move the handle to the

desired position along the barrel and

securely retighten the hand grip (Fig. 9).

HAND GRIP

FIG. 9

X

DEPTH GAUGE

RELEASE BUTTON

DEPTH GAUGE

FIG. 10

# !

! $!

Your tool is equipped with a variable speed

trigger switch. The tool can be turned "ON" or

"OFF" by squeezing or releasing the trigger.

The speed can be adjusted from the minimum

to maximum nameplate RPM by the pressure

you apply to the trigger. Apply more pressure

to increase the speed and release pressure to

decrease speed (Fig. 1).

$#  $!

The reversing switch is used to reverse rotation

of the bit (Fig. 1).

The reversing switch should

only be activated when the

motor is "OFF" and when bit is at a complete

standstill.

To use tool in "Forward" rotation move switch

torward the arrow that depicts forward.

"Reverse" the rotation of the bit move the

switch torward arrow that depicts reverse.

!

CAUTION

7,9(;05.5:;9<*;065:

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 10

-11-

903305.653@ 903305./(44,905. #(90636*2 (44,905.653@

used for drilling used for drilling allows for 12 desired used for light

wood, steel, etc. concrete positions of “hammer” chipping work

FIG. 11

! 

The selector dial allows the tool to be set for

various drilling/hammer drilling and chipping

applications. Depress release button and

turn selector dial right or left depending on

the below applications (Fig. 11).

When using demolition or chipping bits such as

bull points, chisels, spades, gouges, etc. the

“Hammer Only” mode must be selected.

656;67,9(;,;/,:,3,*;065

+0(3<5;03;/,;663*64,:;6(

*6473,;,:;67 Shifting during rotation of the

chuck can cause damage to the tool.

# !

The vario-lock can be set in any one of twelve

positions (30˚ increments). Choose a position

which is best suited for your operation. The

Vario-Lock position is intended for use with

chipping bits such as bull points, spades,

gouges, etc.

Rotate the selector dial, to the “vario-lock”

setting. Next, rotate the locking sleeve,

along with the accessory, to the desired

position. Then turn the selector dial to the

“hammer only” setting and slightly turn the

locking sleeve to have it automatically lock

into a definite position.

!

CAUTION

#!

 

The integrated vibration damper in the main

handle and hammer mechanism reduces

vibrations (Fig. 1).

"!

The tool has a internal pre-set slip clutch. The

output spindle will stop rotating if the accessory

binds and overloads the tool.

!!

Following a few simple tips will reduce wear

on the tool and the chance of injury to the

operator.

The high efficiency available from the BOSCH

Rotary Hammer can only be obtained if sharp

and undamaged drilling tools are used. Note

that the costs for maintaining sharp drilling

tools are more than offset by the time lost in

operating dull drilling tools.

All grease packed hammers require a short

time to warm up. Depending on the

temperature, this time will vary from

approximately 15 seconds (90° F) to 2

minutes (32° F). The tool will exert its full

power and hammering action after the heat

from impact hammering has spread, softening

the grease.

!!

Used for drilling stone, concrete, cement,

brick, cinder block and other unusually hard

non-metals. The Rotary Hammer is designed

for “SDS” Carbide Tipped Bits up to 3/4 inch

diameter.

$"

The 3 Jaw Chuck can convert your tool for

use with straight shank bits.

You will extend the life of your bits and do

neater work if you always put the bit in contact

with the workpiece BEFORE pulling the

trigger. During operation, hold the drill firmly

and exert moderate, steady pressure. Too

much pressure at low speed will stall the

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 11

-12-

hammer. Too little pressure will keep the bit

from cutting and cause excess friction by

sliding over the surface. This can be

damaging to the drill and bit.

Shanks of all drill bits should be wiped clean

prior to using and immediately after removing.

!  !"! 

!

1. Some materials require slow drilling

speeds; whereas, others require higher speed

to produce the best results.

2. All work must be supported or secured

before drilling and steady, even pressure

applied in line with the drill bit.

3. As the drill bit cuts through the opposite

side, reduce the pressure and continue

running the drill as the bit is withdrawn.

Materials such as glass, porcelain, ceramics,

tiles, plastics, etc., should be drilled at low

speeds with specially designed drill bits and

lubricants.

$ !

If backing block is not used, ease up on the

pressure just before the bit breaks through the

wood to avoid splintering. Complete the hole

from the opposite side immediately after the

point breaks through. If bit binds, reverse the

drilling operation to help remove the bit from

the work.

!

Make a center punch in the material for easier

starting. Use enough pressure to keep the bit

cutting. If the bit is allowed to merely spin in

the hole, it will become dull within a short time.

When drilling a larger hole, it is faster and

easier on your power pack to first make a

smaller hole and enlarge it to the required

size. Lubricate the tip of the bit occasionally

with CUTTING OIL for easier metal drilling. If

bit binds, reverse the drilling to help remove

the bit from the work.

 &

Use carbide-tipped SDS-plus

®

bit for cinder

block, mortar, common brick, soft stone and

other materials. The amount of pressure to be

used is dependent upon the type of material

being drilled. Soft materials require less

pressure while the hard materials need more

pressure to prevent the drill bit from spinning.

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 12

-13-

* Auxiliary Handle

* Carrying case

(*= standard equipment)

(**= optional accessories)

- (5 ,?;,5:065 *69+ 0:

5,*,::(9@ ( *69+ >0;/

(+,8<(;, :0A, *65+<*;69: ;/(; 0: *(7()3,

6-*(99@05.;/,*<99,5;5,*,::(9@-69@6<9

;663 4<:; ), <:,+ This will prevent

excessive voltage drop, loss of power or

overheating. Grounded tools must use 3-wire

extension cords that have 3-prong plugs and

receptacles.

!The smaller the gauge number, the

heav i er the cord.

 ' %! 

#!!!"!!

**,::690,:

,9=0*,

9,=,5;0=, 4(05;,5(5*,

7,9-694,+ )@ <5(<;/

690A,+7,9:655,34(@9,:<3;0540:73(*05.

6- 05;,95(3 >09,: (5+ *64765,5;: >/0*/

*6<3+ *(<:, :,906<: /(A(9+ We

recommend that all tool service be performed

by a Bosch Factory Service Center or Autho -

rized Bosch Service Station.

!"!

Your Bosch tool has been properly lubricated

and is ready to use. It is recommended that

tools with gears be regreased with a special

gear lubricant at every brush change.

" 

The brushes and commutator in your tool

have been engineered for many hours of

dependable service. To maintain peak

efficiency of the motor, we recommend every

two to six months the brush es be examined.

Only genuine Bosch replace ment brushes

specially designed for your tool should be

used.



Every second brush change, the bearings

should be replaced at Bosch Factory Service

Center or Au thorized Bosch Service Station.

Bearings which become noisy (due to heavy

load or very abrasive material cut ting) should

be replaced at once to avoid overheating or

motor failure.

3,(505.

!6(=60+(**0+,5;:(3>(@:

+0:*655,*; ;/, ;663 -964

;/, 76>,9 :<773@ ),-69, *3,(505. 69

7,9-69405.(5@4(05;,5(5*, The tool may

be cleaned most effectively with compressed

dry air. 3>(@: >,(9 :(-,;@.6..3,: >/,5

*3,(505.;663:>0;/*6479,::,+(09

Ventilation openings and switch levers must

be kept clean and free of foreign matter. Do

not at tempt to clean by inserting pointed

objects through openings.

,9;(05 *3,(505. (.,5;:

(5+ :63=,5;: +(4(.,

73(:;0* 7(9;: Some of these are: gasoline,

carbon tetrachlo ride, chlo rinated cleaning

solvents, ammonia and house hold

detergents that contain ammonia.

(05;,5(5*,

!663C:

47,9,

(;05.

69+ 0A,05$

$09, 0A,:0544



3-6

6-8

8-10

10-12

12-16

18 16 16 14 0.75 0.75 1.5 2.5

18 16 14 12 0.75 1.0 2.5 4.0

16 16 14 12 1.0 2.5 4.0 —

14 12 —— ————

25 50 100 150 15 30 60 120

69+,5.;/05,,; 69+,5.;/05,;,9:

!

CAUTION

!

WARNING

!

WARNING

!

WARNING

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 13

Page is loading ...

-19-

Description fonctionnelle et spécifications

Débranchez la fiche de la prise de courant avant d'effectuer quelque assemblage

ou réglage que ce soit ou de changer les accessoires. Ces mesures de sécurité

préventive réduisent le risque d'une mise en marche accidentelle de l'outil.

AVERTISSEMENT

!

Marteau rotatif

Numéro de modèle RH328VC et RH328VCQ

Type de tige SDS-plus

B

Capacités maximales :

Mèches à pointe au carbure 29 mm

Mèches creuses à paroi mince 83 mm

REMARQUE : Pour spécifications de l'outil, reportez-vous à la plaque signalétique de votre outil.

BOUTON DE BLOCAGE DE LA BUTÉE

DE PROFONDEUR

BAGUE DE

VERROUILLAGE

MANCHON DE

VERROUILLAGE

MANDRIN

SDS-plus

®

POIGNEE

AUXILIAIRE

POIGNEE (PRISE)

POIGNÉE D'AMORTISSEMENT

DES VIBRATIONS/MÉCANISME

D'ACTIONNEMENT DU

MARTEAU

GÂCHETTE DE

COMMANDE À

VITESSE

VARIABLE

INTERRUPTEUR

D'INVERSION DE

MARCHE

CADRAN DE

SÉLECTION DE

PERCEUSE/PERCEUSE

À PERCUSSION

FIG. 1

BUTÉE DE PROFONDEUR

PARE-

POUSSIÈRE

MANDRIN À 3 MORS

(Non fourni, disponible à

titre d’accessoire)

OUVERTURES

DE

VENTILATION

BOUTON DE

DÉCLENCHEMENT

SDS-plus

®

MANDRIN À CHANGEMENT RAPIDE

(modèle RH328VCQ seulement)

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 19

Page is loading ...

Notes:

-38-

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 38

-39-

Remarques :

Notas:

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 39

1619929E58 07/12

LIMITED WARRANTY OF BOSCH PORTABLE AND BENCHTOP POWER TOOLS

Robert Bosch Tool Corporation (“Seller”) warrants to the original purchaser only, that all BOSCH portable and benchtop power tools will be free from

defects in material or workmanship for a period of one year from date of purchase. SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY

under this Limited Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall be the repair or replacement of parts,

without charge, which are defective in material or workmanship and which have not been misused, carelessly handled, or misrepaired by persons

other than Seller or Authorized Service Station. To make a claim under this Limited Warranty, you must return the complete portable or benchtop

power tool product, transportation prepaid, to any BOSCH Factory Service Center or Authorized Service Station. For Authorized BOSCH Power Tool

Service Stations, please refer to your phone directory.

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW

BLADES, SANDING BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.

ANY IMPLIED WARRANTIES SHALL BE LIMITED IN DURATION TO ONE YEAR FROM DATE OF PURCHASE. SOME STATES IN THE U.S., SOME

CANADIAN PRO V INCES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT

APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY

FOR LOSS OF PROFITS) ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S. AND SOME CANADIAN PROVINCES

DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR

EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO

STATE IN THE U.S., PROVINCE TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PORTABLE AND BENCHTOP ELECTRIC TOOLS SOLD WITHIN THE UNITED STATES OF AMERICA,

CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL

BOSCH DEALER OR IMPORTER.

GARANTIE LIMITÉE DES OUTILS ÉLECTRIQUES PORTATIFS ET D'ÉTABLI BOSCH

Robert Bosch Tool Corporation (le « vendeur ») garantit à l'acheteur initial seulement que tous les outils électriques portatifs et d'établi BOSCH

seront exempts de vices de matériaux ou d'exécution pendant une période d'un an depuis la date d'achat. LA SEULE OBLIGATION DU VENDEUR ET

LE SEUL RECOURS DE L’ACHETEUR sous la présente garantie limitée, et en autant que la loi le permette sous toute garantie ou condition implicite

qui en découlerait, sera l’obligation de remplacer ou réparer gratuitement les pièces défectueuses matériellement ou comme fabrication, pourvu que

lesdites défectuosités ne soient pas attribuables à un usage abusif ou à quelque réparation bricolée par quelqu’un d’autre que le vendeur ou le

personnel d’une station-service agréée. Pour présenter une réclamation en vertu de cette garantie limitée, vous devez renvoyer l'outil électrique

portatif ou d'établi complet, port payé, à tout centre de service agréé ou centre de service usine. Veuillez consulter votre annuaire téléphonique

pour les adresses.

LA PRÉSENTE GARANTIE NE S’APPLIQUE PAS AUX ACCESSOIRES TELS QUE LAMES DE SCIES CIRCULAIRES, MÈCHES DE PERCEUSES, FERS

DE TOUPIES, LAMES DE SCIES SAUTEUSES, COURROIES DE PONÇAGE, MEULES ET AUTRES ARTICLES DU GENRE.

TOUTE GARANTIE IMPLICITE SERA LIMITÉE COMME DURÉE À UN AN À COMPTER DE LA DATE D’ACHAT. CERTAINS ÉTATS AMÉRICAINS,

CERTAINES PROVINCES CANADIENNES N’ADMETTANT PAS LE PRINCIPE DE LA LIMITATION DE LA DURÉE DES GARANTIES IMPLICITES, IL

EST POSSIBLE QUE LES LIMITATIONS CI-DESSUS NE S’APPLIQUENT PAS À VOTRE CAS.

EN AUCUN CAS LE VENDEUR NE SAURAIT ÊTRE TENU POUR RESPONSABLE DES INCIDENTS OU DOMMAGES INDIRECTS (INCLUANT, MAIS NE

SE LIMITANT PAS AUX PERTES DE PROFITS) CONSÉCUTIFS À LA VENTE OU L’USAGE DE CE PRODUIT. CERTAINS ÉTATS AMÉRICAINS ET

CERTAINES PROVINCES CANADIENNES N’ADMETTANT PAS LE PRINCIPE DE LA LIMITATION NI L’EXCLUSION DES DOMMAGES INDIRECTS ET

CONSÉQUENTIELS, IL EST POSSIBLE QUE LES LIMITATIONS OU EXCLUSIONS CI-DESSUS NE S’APPLIQUENT PAS À VOTRE CAS.

LA PRÉSENTE GARANTIE VOUS ACCORDE DES DROITS BIEN DÉTERMINÉS, Y COMPRIS POSSIBLEMENT CERTAINS DROITS VARIABLES DANS

LES DIFFÉRENTS ÉTATS AMÉRICAINS, PROVINCES CANADIENNE ET DE PAYS À PAYS.

CETTE GARANTIE LIMITÉE NE S'APPLIQUE QU'AUX OUTILS ÉLECTRIQUES PORTATIFS ET D'ÉTABLI VENDUS AUX ÉTATS-UNIS D'AMÉRIQUE,

AU CANADA ET AU COMMONWEALTH DE PORTO RICO. POUR COUVERTURE DE GARANTIE DANS LES AUTRES PAYS, CONTACTEZ VOTRE

IMPORTATEUR OU REVENDEUR BOSCH LOCAL.

GARANTIA LIMITADA PARA HERRAMIENTAS MECANICAS PORTATILES Y PARA TABLERO DE BANCO BOSCH

Robert Bosch Tool Corporation ("el Vendedor") garantiza, únicamente al comprador original, que todas las herramientas mecánicas portátiles y

para tablero de banco BOSCH estarán libres de defectos de material o de fabricación durante un período de un año a partir de la fecha de compra.

LA UNICA OBLIGACION DEL VENDEDOR Y EL RECURSO EXCLUSIVO QUE USTED TIENE bajo esta Garantía Limitada y, hasta donde la ley lo

permita, bajo cualquier garantía o condición implícita por ley, consistirá en la reparación o sustitución sin costo de las piezas que presenten

defectos de material o de fabricación y que no hayan sido utilizadas inco rrectamente, manejadas descuidadamente o reparadas incorrectamente

por personas que no sean el Vendedor o una Estación de servicio autorizada. Para efectuar una reclamación bajo esta Garantía Limitada, usted

debe devolver el producto, que consiste en la herramienta mecánica portátil o para tablero de banco completa, con el transporte pagado, a

cualquier Centro de servicio de fábrica o Estación de servicio autorizada. Para Estaciones de servicio autorizadas de herramientas mecánicas

BOSCH, por favor, consulte el directorio telefónico.

ESTA GARANTIA LIMITADA NO SE APLICA A ARTICULOS ACCESORIOS TALES COMO HOJAS PARA SIERRAS CIRCULARES, BROCAS PARA

TALADROS, BROCAS PARA FRESADORAS, HOJAS PARA SIERRAS DE VAIVEN, CORREAS PARA LIJAR, RUEDAS DE AMOLAR Y OTROS

ARTICULOS RELACIONADOS.

TODAS LAS GARANTIAS IMPLICITAS TENDRAN UNA DURACION LIMITADA A UN AÑO A PARTIR DE LA FECHA DE COMPRA. ALGUNOS

ESTADOS DE LOS EE.UU. Y ALGUNAS PROVINCIAS CANADIENSES NO PERMITEN LIMITACIONES EN CUANTO A LA DURACION DE UNA

GARANTIA IMPLICITA, POR LO QUE ES POSIBLE QUE LA LIMITACION ANTERIOR NO SEA APLICABLE EN EL CASO DE USTED.

EL VENDEDOR NO SERA RESPONSABLE EN NINGUN CASO DE NINGUN DAÑO INCIDENTAL O EMERGENTE (INCLUYENDO PERO NO LIMITADO

A RESPONSABILIDAD POR PERDIDA DE BENEFICIOS) QUE SE PRODUZCA COMO CONSECUENCIA DE LA VENTA O UTILIZACION DE ESTE

PRODUCTO. ALGUNOS ESTADOS DE LOS EE.UU. Y ALGUNAS PROVINCIAS CANADIENSES NO PERMITEN LA EXCLUSION O LIMITACION DE

LOS DAÑOS INCIDENTALES O EMERGENTES, POR LO QUE ES POSIBLE QUE LA LIMITACION O EXCLUSION ANTERIOR NO SEA APLICABLE EN

EL CASO DE USTED.

ESTA GARANTIA LIMITADA LE CONFIERE A USTED DERECHOS LEGALES ESPECIFICOS Y ES POSIBLE QUE USTED TAMBIEN TENGA OTROS

DERECHOS QUE VARIAN DE ESTADO A ESTADO EN LOS EE.UU., DE PROVINCIA A PROVINCIA EN CANADA Y DE UN PAIS A OTRO.

ESTA GARANTIA LIMITADA SE APLICA SOLAMENTE A HERRAMIENTAS ELECTRICAS PORTATILES Y PARA TABLERO DE BANCO VENDIDAS EN

LOS ESTADOS UNIDOS DE AMERICA, CANADA Y EL ESTADO LIBRE ASOCIADO DE PUERTO RICO. PARA COBERTURA DE GARANTIA EN OTROS

PAISES, PONGASE EN CONTACTO CON SU DISTRIBUIDOR O IMPORTADOR LOCAL DE BOSCH.

Exportado por: Robert Bosch Tool Corporation Mt. Prospect, IL 60056 -2230, E.U.A.

Importado a México por: Robert Bosch, S.A. de C.V., Calle Robert Bosch No. 405, Zona

Industrial, Toluca, Edo. de México, C.P. 50070, Tel. (722) 2792300

!1619929E58!

BM 1619929E58 07-12_BM 1619929E58 07-12 8/1/12 8:02 AM Page 40

Bosch RH328VC HDC100 User manual

This manual is also suitable for

Bosch RH328VC HDC100 User manual

in other languages

Related papers

Other documents