SINGER 44S Owner's manual

Category
Sewing machines
Type
Owner's manual

This manual is also suitable for

44S
Manuel d'Instruction
Instruction Manual
Manual de Instrucciones
IMPORTANT SAFETY INSTRUCTIONS
EN
When using an electrical appliance, basic safety should always be
followed, including the following:
Read all instructions before using this sewing machine.
1. An appliance should never be left unattended when plugged in.
2. Always unplug this appliance from the electric outlet immediately
after using and before cleaning.
3.
1. Do not allow to be used as a toy. Close attention is necessary
when this appliance is used by or near children.
2. Use this appliance only for its intended use as described in this
manual. Use only attachments recommended by the
manufacturer as contained in this manual.
3. Never operate this appliance if it has a damaged cord or plug, if it
is not working properly, if it has been dropped or damaged, or
dropped into water. Return the appliance to the nearest
authorized dealer or service center for examination, repair,
electrical or mechanical adjustment.
4. Never operate the appliance with any air openings blocked. Keep
ventilation openings of the sewing machine and foot controller
free from accumulation of lint, dust, and loose cloth.
5. Keep fingers away from all moving parts. Special care is required
around the sewing machine needle.
6. Always use the proper needle plate. The wrong plate can cause
the needle to break.
7. Do not use bent needles.
8. Do not pull or push fabric while stitching. It may deflect the
needle causing it to break.
9. Switch the sewing machine off ("O") when making any adjustments
in the needle area, such as threading needle, changing needle,
threading bobbin, or changing presser foot, and the like.
10. Always unplug sewing machine from the electrical outlet when
removing covers, lubricating, or when making any other user
servicing adjustments mentioned in the instruction manual.
11. Never drop or insert any object into any opening.
12. Do not use outdoors.
13. Do not operate where aerosol spray products are being used or
where oxygen is being administered.
14. To disconnect, turn all controls to the off ("O") position, then
remove plug from outlet.
15. Do not unplug by pulling on cord. To unplug, grasp the plug, not
the cord.
This sewing machine is intended for household use only.
DANGER
WARNING
- To reduce the risk of electric shock:
- To reduce the risk of burns, fire, electric
shock, or injury to persons:
Please turn off the machine or unplug when the machine is not
operating properly.
18. Never place anything on the foot controller.
19. If the supply cord that is fixed with foot controller is damaged, it
must be replaced by the manufacturer or its service agent or a
similar qualified person in order to avoid a hazard.
20. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
21. Children should be supervised to ensure that they do not play
with the appliance.
SAVE THESE INSTRUCTIONS
The LED lamp maximum power is 0.3W, maximum voltage is DC
9V. If the lamp is damaged, you should not use the product, send
it to SINGER or a service agent to repair or replace at once.
16. The sound pressure level under normal operating conditions is
75dB(A).
17.
Como propietario/ a de una nueva
máquina de coser Singer, usted acaba
de iniciar una gran oportunidad para
plasmar su creatividad. Desde el
momento en que utilice por primera
vez su máquina, se dará cuenta de que
está cosiendo con una de las
máquinas más fáciles de utilizar.
Le recomendamos encarecidamente
que, antes de comenzar a utilizar su
máquina de coser, conozca las
numerosas ventajas y su facilidad de
uso leyendo detenidamente este
manual de instrucciones, paso a paso,
sentado ante su máquina.
Para cerciorarse de que siempre
dispondrá de las más modernas
capacidades para coser, el fabricante
se reserva el derecho de cambiar la
apariencia, diseño y accesorios de está
máquina cuando lo considere
necesario.
SINGER es una marca registrada de
"The Singer Company Limited S.à.r.l."
o sus Afiliadas. ©2013 The Singer
Company Limited S.à.r.l. o sus
Afiliadas. Todos los derechos
reservados.
Vous voici à présent propriétaire d'une
machine à coudre Singer et en cette
qualité, vous allez
vous lancez dans une aventure
excitante dans le domaine de la
créativité. Dès le départ, vous
réaliserez que vous allez coudre avec
l'une des machines les plus faciles à
utiliser qui ait jamais été fabriquée.
Avant de commencer à coudre, nous
vous recommandons de voir quelques
avantages ainsi que la facilité
d'utilisation en lisant ce mode d'emploi
en étant assis devant votre machine à
coudre.
Afin de garantir que votre machine
vous donnera toujours le meilleur du
point de vue technique, le fabricant se
réserve le droit de modifier l'apparence,
le concept ou les accessoires de cette
machine s'il le juge nécessaire.
SINGER est une marque exclusive de
The Singer Company Limited S.à.r.l. ou
de ses Affiliés. ©2013 The Singer
Company Limited S.à.r.l. ou de ses
Affiliés. Tous droits réservés.
As the owner of a new Singer sewing
machine, you are about to begin an
exciting adventure in creativity. From
the moment you first use your machine,
you will know you are sewing on one of
the easiest to use sewing machines
ever made.
May we recommend that, before you
start to use your sewing machine, you
discover the many features and the
ease of operation by going through this
instruction book, step by step, seated
at your machine.
To ensure that you are always provided
with the most modern sewing
capabilities, the manufacturer reserves
the right to change the appearance,
design or accessories of this sewing
machine when considered necessary.
SINGER is the exclusive trademark of
The Singer Company Limited S.à.r.l. or
its Affiliates. ©2013 The Singer
Company Limited S.à.r.l. or its Affiliates.
All rights reserved.
E
F
Congratulations
Felicitaciones
Félicitations
EN
List of contents
EN
Machine Basics
Sewing
General Information
Maintenance and Troubleshooting
Principle Parts of the Machine .........................................................................................................................................................2/4
Connecting Machine to Power Source................................................................................................................................................6
Two Step Presser Foot Lifter/ .........................................................................................................8
Accessories.......................................................................................................................................................................................10
Winding the Bobbin...........................................................................................................................................................................12
Inserting the Bobbin ..........................................................................................................................................................................14
Threading the Upper Thread.............................................................................................................................................................16
Raising the Bobbin Thread ...............................................................................................................................................................20
How to Choose Your Pattern.............................................................................................................................................................24
Sewing Straight Stitch.......................................................................................................................................................................30
Reverse Sewing/ ..............................................................................................................32
Blind Hem .........................................................................................................................................................................................36
....................................................................................................................................................................38
Sewing on Buttons ............................................................................................................................................................................42
Installing the Removable Extension Table ........................................................................................................................................44
Attaching the Presser Foot Shank ....................................................................................................................................................46
Needle/ Fabric/ Thread Chart ...........................................................................................................................................................48
....................................................................................................................................................................51
Inserting & Changing Needle ............................................................................................................................................................53
Troubleshooting Guide......................................................................................................................................................................55
Adjusting Presser Foot Pressure
Automatic Needle Threader ..............................................................................................................................................................18
Thread Tension .................................................................................................................................................................................22
Stitch Width Dial & Stitch Length Dial ...............................................................................................................................................28
Removing the Work/ Cutting the Thread
Sew 1-step Buttonholes
Threading the Machine
Choosing Stretch Stitch Patterns ......................................................................................................................................................34
Three Needle Position Dial ...............................................................................................................................................................26
Left and Right Side Balance for Buttonhole ......................................................................................................................................40
How To Drop Feed Dog
2
Principal Parts of the Machine
EN
1. Thread tension dial
2. Presser foot pressure adjustment
3. Thread take-up lever
4. Reverse sewing lever
5. Thread cutter
6. Presser foot
7. Needle plate cover
8. Removable extension table/ accessory storage
9. Three needle position dial
10. Bobbin stopper
11. Stitch width dial
12. Stitch length dial
13. Pattern selector dial
14. Automatic threader
15. One step buttonhole lever
14
15
1
2
3
5
6
8
7
13
11
12
10
4
9
4
Principal Parts of the Machine
EN
16. Horizontal spool pin
17. Bobbin winding spindle
18. Hole for second spool pin
19. Handwheel
20. Buttonhole stitch balance adjustment slot
21. Power and light switch
22. Main plug socket
23. Bobbin thread guide
24. Upper thread guide
25. Face plate
26. Handle
27. Presser foot lifter
28.
29. Foot speed control
30. Power cord
Drop feed control
29
30
25
26
28
23
24
27
20
21
22
16
17
19
18
23
6
1
A
Connecting Machine to Power Source
EN
a
b
Connect the machine to a power source as illustrated. (1)
This appliance is equipped with a polarized plug which must
be used with the appropriate polarized outlet. (2)
Unplug power cord when machine is not in use.
The foot control pedal regulates the sewing speed. (3)
Consult a qualified electrician if in doubt of how to connect
machine to power source.
Unplug power cord when machine is not in use.
The foot control must be used with the appliance by
(110-120V area)/ (220-240V area)/
(110-125V area).
Press main switch (A) to"l"forpower and light.
For appliance with a polarized plug (one blade is wider
than the other). To reduce the risk of electric shock, this
plug is intended to fit in a polarized outlet only one way. If
it does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install the
proper outlet. Do not modify the plug in any way.
Attention:
Foot control
Attention:
Sewing light
IMPORTANT NOTICE
a. Polarized attachment plug
b. Conductor intended to be grounded
FC-
1902A FC-2902A 4C-
316Q
When sewing several layers or thick fabrics, the presser foot
can be raised to a higher position for easy positioning of the
work. (A)
The presser foot will remain raised as long as you hold up
the presser foot lifter. As soon as you release it, the presser
foot will drop back down to the intermediate position.
The presser foot pressure of the machine has been pre-set
and requires no particular readjustment according to the type
of fabric (light-or-heavy weight).
However, if you need to adjust the presser foot pressure,
turn the presser adjusting screw with a coin.
For sewing very thin fabric, loosen the pressure by turning
the screw counter clockwise, and for heavy fabric, tighten by
turning it clockwise.
It is suggested that you turn the screw in one quarter inch
increments so that it can be easily reset to factory settings.
8
Two Step Presser Foot Lifter
EN
A
Adjusting Presser Foot Pressure
006918008
1 Standard accessories
2 Optional accessories
Standard accessories (1)
Optional accessories (2)
a. All purpose foot
b. Zipper foot
c. Buttonhole foot
d. Button sewing foot
e. Seam ripper/ brush
f. Edge/ quilting guide
g. Pack of needles
h. Spool holders
i. Bobbin (3x)
j. L-screwdriver
k. Auxiliary Spool Pin
l. Spool pin felt
m. Soft cover
(These 10 accessories are not supplied with this machine;
they are, however, available for purchase from your authorized
retailer.)
n. Satin stitch foot
o. Overcasting foot
p. Hemmer foot
q. Cording foot
r. Blind hem foot
s. Quilting/ straight stitch foot
t. Gathering foot
u. Darning/ embroidery foot
v. Even Feed foot
w. Twin needle
onpqr
s
t
u
vw
006916008 006016008006917008 0061850081
006904008006172008 006907008 006900008
006813008
Accessories
EN
10
m
h
g
e
f
i
j
l
k
a
b
c
d
006905008 006914008
006Q6A0150
- Place thread and corresponding spool holder on to spool
pin. (1/2)
- Snap thread into thread guide. (3)
- Wind thread clockwise around bobbin winder tension discs. (4)
- Thread bobbin as illustrated and place on spindle. (5)
- Push bobbin spindle to right. (6)
- Hold thread end securily. (7)
- Step on foot control pedal. (8)
- Trim thread close to the bobbin & then continue winding
until bobbin is full. (9)
- Cut thread, push bobbin spindle to left (10) and remove.
When the bobbin winder spindle is in "bobbin winding"
position, the machine will not sew and the .
To start sewing, push the bobbin winder spindle to the left
(sewing position).
Please Note:
handwheel turn
1
2
4
7
8
9
5
6
3
10
Winding the Bobbin
EN
12
A
B
C
1
3
4
2
Inserting the Bobbin
EN
14
When inserting or removing the bobbin, raise the presser
foot & make sure the needle is fully raised.
Attention:
1. Remove the bobbin cover plate by pushing the small tab
to the right of the cover towards the right.
2. Insert the bobbin in the bobbin case with the thread
running counterclockwise direction (arrow).
3. Pull the thread through the slit (A).
4. Draw the thread clockwise until it slips into the notch (B),
while holding the bobbin down with the tip of your finger.
5. Pull out about 15 cm (6 inches) of thread towards the
back of the plate and attach the bobbin cover plate. (C)
Turn power switch to off ("O") before inserting or
removing the bobbin.
This is a simple operation but it is important to carry out correctly as
by not doing so .
- Start by raising the needle to its highest point (1), and continue
turning the handwheel* counterclockwise until the needle just
slightly begins to descend. You must raise the presser foot to
release the tension discs.
For safety, it is strongly suggested you turn off the power
before threading.
- Lift up the spool pin. Place the spool of thread on the holder with
the thread coming off the spool from the back as shown and
place appropriate spool holder next to the spool. For small
thread spools, place small side of spool holder next to spool. (2)
- Draw thread from spool through the upper thread guide (3) and
pulling thread through pre-tension spring as illustrated. (4)
- Thread tension module by leading thread down right channel. (5)
During this process it is helpful to hold the thread between the
spool and thread guide, as this will help to seat the thread
between the tension discs.
- At the top of this movement pass thread from right to left through
the slotted eye of the take-up lever and then downwards again.
(6)
- Now pass the thread behind the horizontal thread guide, and
then behind the thin wire needle clamp guide (7) and then down
to the needle which should be threaded from front to back.
- Pull about 6 - 8 inches of thread under the presser foot to the rear
beyond the needle eye. Trim thread to length with built-in thread
cutter. (8)
* Never turn the handwheel away from you as this may cause the
timing to be disrupted. Always turn the handwheel
counterclockwise (towards you).
several sewing problems could result
Note:
2
1
6
8
7
5
3 4
Threading the Upper Thread
EN
16
- Thread upper tension of machine up to the thin wire in front
of the needle clamp.
- Raise the needle to its highest position.
- Set machine to straight stitch.
- Press lever (A) down as far as it will go, and gently insert
the hook of the threader into the eye of the needle by
swinging the lever towards you when it is fully lowered.
- The threader automtically swings to the threading position
(B).
- Pass thread under thread guide (C), from left to right.
- Pass the thread in front of the needle around the hook (D)
from bottom to top.
- Release lever (A), by swinging it away from you & then
pushing it back up to the resting position.
- Pull the thread through the needle eye.
Turn power switch to off ("O")!
Attention:
Automatic Needle Threader
1
2
A
B
C
D
A
EN
18
1
2
3
Hold the upper thread with the left hand. Turn the handwheel
(1) towards you (counterclockwise) lowering, then raising
needle.
If it is difficult to raise the bobbin thread, check to make sure
the thread is not trapped by the hinged cover or the
Removable Extension Table.
Gently pull on the upper thread to bring the bobbin thread up
through the needle plate hole. (2)
Lay both threads to the back under the presser foot. (3)
Note:
Raising the Bobbin Thread
EN
20
Upper thread tension
Lower thread tension
Please note:
Basic thread tension setting: "4". (1)
To increase the tension, turn the dial to the next number up.
To reduce the tension, turn the dial to the next number down.
A. Normal thread tension for straight stitch sewing.
B. Thread tension too loose for straight stitch sewing. Turn dial
to higher number.
C. Thread tension too tight for straight stitch sewing. Turn dial to
lower number.
D. Normal thread tension for zig zag and decorative sewing.
Correct thread tension is when a small amount of the upper
thread appears on the bottom side of fabric.
If the thread is looping or birdnesting on the underside of the
fabric, this is an indication that the upper machine tension is not
threaded correctly.
The bobbin tension has been set correctly at the factory, so you
do not need to adjust it.
- Proper tension setting is important for strong seams.
- There is no single tension setting appropriate for all stitch
functions, thread or fabric.
- A balanced tension (identical stitches both top and bottom) is
usually only desirable for straight stitch construction sewing.
- 90% of all sewing will be between "3" and "5".
- For zig zag and decorative sewing stitch functions, thread
tension should generally be less than for straight stitch sewing.
- For all decorative sewing you will always obtain a nicer stitch
and less fabric puckering when the upper thread appears on
the bottom side of your fabric.
- If the thread is looping or birdnesting on the top of the fabric,
this is an indication that the bobbin thread has not been
threaded correctly.
22
BA
C
D
1
Thread Tension
EN
The diagram on this page display the stitch patterns available
on the machine.
Stitches in the top of the diagram are indicated on the pattern
selector dial in gray. To select the patterns indicated with the
gray color, turn the pattern selector dial. (e) Use the stitch
length dial (d) to adjust the stitch length as desired for the
project. Use the stitch width dial (c) to adjust the width of the
stitch as desired. Instructions for setting the stitch width & the
stitch length dials can be found on page 28.
Stitches in the bottom row of the diagram are indicated on
the pattern selector dial in blue. The blue indicates that the
stitch is a stretch stitch pattern, and information on how to
sew these stretch patterns is on page 34.
The pattern selector dial may be turned in either direction.
a.Reverse sewing lever
b.Three needle position dial
c. Stitch width dial
d.Stitch length dial
e.Pattern selector dial
24
How to Choose Your Pattern
EN
BAIKDC
J
EGFH
S1
BAIKDC
J
EGFH
c
e
d
a b
26
The needle position can be altered with the "Three needle
position dial". For normal work, the needle position is middle.
For edge stitching or sewing parallel lines of top stitch, select
needle position left or right. For twin needle stitching, needle
position is middle.
a. Straight
b. Zig-zag
L. Left Needle Position
M. Middle Needle Position
R. Right Needle Position
Three Needle Position Dial
EN
L M R
a
b
Function of stitch width dial
Function of stitch length dial while zig-zag stitching
Function of stitch length dial for when straight stitching
When doing a zig zag or a decorative pattern you can alter
the width from 1mm to 6mm. To obtain a very narrow stitch,
set the dial to 1, to obtain the maxinum 6mm width, set the
dial to 6. When the dial is set to 0, you will obtain a straight
stitch. (1)
Set the pattern selector dial to zig zag or any other
decorative pattern.
The density of zig zag or decorative stitches increases as the
setting of the stitch length dial approaches "0". The smaller
the number the closer, or denser the stitches will be.
Standard zigzag stitches are usually achieved at "3" or below. (2)
Dense zig-zag stitches are called satin stitches. (2)
For straight stitch sewing, turn the pattern selector dial to the
straight stitch setting. Turn the stitch length dial, and the
length of the individual stitches will decrease as the dial
approached "0". The length of the individual stitches will
increase as the dial approaches "4". Generally speaking, use
a longer stitch length when sewing heavier weight fabrics or
when using a thicker needle or thread. Use a shorter stitch
length when sewing lighter weight fabrics or when using a
finer needle or thread.
- The standard setting for sewing a seam is between 2 and 3.
- For basting purposes, set the stitch length all the way to 4
(longest).
28
1
2
4
3
21
0.5
Stitch Width Dial & Stitch Length Dial
EN
To begin sewing, set the machine for straight stitch. (1)
Set the stitch length to between 2 and 3.
Place the fabric under the presser foot with the fabric edge
lined up with the desired seam guide line on the needle plate.
(2)
Lower the presser foot lifter, and then step on the foot
controller to start sewing. (3)
30
1
2
3
Sewing Straight Stitch
EN
32
Turn the handwheel toward you (counterclockwise) to bring
the thread take up lever to its highest position, raise the
presser foot and remove work behind
(2)
the needle and presser
foot.
Pull the threads under and behind the presser foot. Guide
the threads to the side of the face plate and into thread cutter
(B). Pull threads down to cut. (3)
To secure the beginning and the end of a seam, press down
the reverse sewing lever (A). Sew a few reverse stitches.
Release the lever and the machine will sew forward again. (1)
1
3
2
A
B
Removing the Work
Cutting the Thread
Reverse Sewing
EN
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65

SINGER 44S Owner's manual

Category
Sewing machines
Type
Owner's manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI