Wolf CHALLENGER XL C72SS User manual

Brand: Wolf

Model: CHALLENGER XL C72SS

Category: Fireplaces

Type: User manual

INSTALLATION & OPERATION MANUAL

CHALLENGER XL Series

Gas Restaurant Ranges

MODELS:

C24S C36(S,C)

C48(S,C) C48SS

C60(S,C)(S,C) C72(S,C)(S,C)

www.wolfrange.com

ITW Food Equipment Group, LLC

10405 Westlake Drive

Charlotte, NC 28273

RETAIN THIS MANUAL FOR FUTURE USE

FORM F35696 Rev. E (07-08)

IMPORTANT FOR YOUR SAFETY

THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL GAS

EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD START-UP AND

ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.

POST IN A PROMINENT LOCATION THE INSTRUCTIONS TO BE FOLLOWED IN THE

EVENT THE SMELL OF GAS IS DETECTED. THIS INFORMATION CAN BE OBTAINED

FROM THE LOCAL GAS SUPPLIER.

IMPORTANT

In the event a gas odor is detected, shut

down units at main shutoff valve and

contact the local gas supplier for service.

FOR YOUR SAFETY

Do not store or use gasoline or other

flammable vapors or liquids in the vicinity of

this or any other appliance.

Improper installation, adjustment, alteration,

service or maintenance can cause property

damage, injury or death. Read the

installation, operating and maintenance

instructions thoroughly before installing or

servicing this equipment.

IN THE EVENT OF A POWER FAILURE, DO NOT

ATTEMPT TO OPERATE THIS DEVICE.

- 2 -

- 3 -

INSTALLATION, OPERATION AND CARE OF

CHALLENGER XL SERIES GAS RESTAURANT RANGES

PLEASE KEEP THIS MANUAL FOR FUTURE USE

GENERAL

Wolf ranges and ovens are produced with quality workmanship and material. These ranges are

designed with efficiency in cooking performance, sanitation and ease of cleaning ability in mind. Proper

installation, usage and maintenance of your range will result in many years of satisfactory performance.

The manufacturer suggests that you thoroughly read this entire manual and carefully follow all of the

instructions provided.

OPTIONAL FIELD INSTALLABLE ACCESSORIES

DESCRIPTION

ACCESSORIES

Flue Devices

- 23" (584 mm) high stainless steel backsplash with broiler mounting brackets

- Stainless steel stub riser

Flex Hose and Quick

Disconnect

- ¾” (18.75 mm) flex hose / disconnect, 4’ (1219 mm long).

- 1" (25 mm) flex hose / disconnect, 4' (1219 mm) long.

Oven Racks

- 1 extra rack with standard and convection ovens.

- 1 extra pair of rack slides with standard ovens.

Casters

- Set of four 6" (152 mm) casters.

- Set of six 6" (152 mm) casters.

INSTALLATION

UNPACKING

This range was inspected before leaving the factory. The transportation company assumes full

responsibility for safe delivery upon acceptance of the shipment. Immediately after unpacking, check for

possible shipping damage. If the range is found to be damaged, save the packaging material and

contact the carrier within 15 days of delivery.

Carefully unpack range(s) and place in the approximate installation position. Remove parts (packed in a

cardboard box) from oven cavity.

If burner has been shipped using any package strapping devices, remove these before installing the

range.

Before installing, check the type of gas supply (natural or propane) to make sure they agree with the

specifications on the rating plate located on the inside of the kick panel. If the supply and equipment

requirements do not agree, do not proceed with the installation. Contact your dealer immediately.

- 4 -

LOCATION

The equipment area must be kept free and clear of combustible substances.

Installation clearances: COMBUSTIBLE NON-COMBUSTIBLE

CONSTRUCTION

Back: 6" (152 mm) 0"

Right Side: 10" (254 mm) 0"

Left Side: 10" (254 mm) 0"

The installation location must allow adequate clearances for servicing and proper operation. A minimum

front clearance of 35" (889 mm) is required.

The ranges are suitable for installation on combustible floors when 6" (152 mm) adjustable legs or

casters are used. When legs or casters are removed, use only on noncombustible floors, curb, or

platform, with front appliance base projecting 3" (76 mm) beyond curb or platform.

The range(s) must be installed so that the flow of combustion and ventilation air will not be obstructed.

Adequate clearance for air openings into the combustion chamber(s) must be provided. Make sure

there is an adequate supply of air in the room to allow for combustion of the gas at the burners.

INSTALLATION CODES AND STANDARDS

Your Wolf Range must be installed in accordance with:

In the United States of America:

1. State and local codes.

2. National Fuel Gas Code, ANSI-Z223.1/NFPA #54 (latest edition). This shall include but

not be limited to: NFPA #54 Section 10.3.5.2 for Venting. Copies may be obtained

from The American Gas Association Accredited Standards Committee Z223, @ 400 N.

Capital St. NW, Washington, DC 20001 or the Secretary Standards Council, NFPA, 1

Batterymarch Park Quincy, MA 02169-7471.

NOTE: In the Commonwealth of Massachusetts

All gas appliances vented through a ventilation hood or exhaust system equipped with

a damper or with a power means of exhaust shall comply with 248 CMR.

3. NFPA Standard # 96 Vapor Removal from Cooking Equipment, latest edition, available

from the National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

In Canada:

1. Local codes.

2. CAN/CSA-B149.1 Natural Gas Installation (latest edition)

3. CAN/CSA-B149.2 Propane Installation Code (latest edition), available from the

Canadian Gas Association, 178 Rexdale Blvd., Etobicoke, Ontario, Canada M9W 1R3

The above are available from the Canadian Standard Association, 5060 Spectrum Way, Suite 100,

Mississauga, Ontario, Canada L4W 5N6.

LEG/CASTER ASSEMBLY

The range is shipped fully assembled, except for the legs. The range is provided with 6"(152 mm)

adjustable stainless steel legs (hardware included), packaged in a box located inside of the oven. A set

of 6"(152 mm) casters are available as an optional field installable accessory.

RANGE SERIES LEGS TO INSTALL CASTERS TO INSTALL

C24 4 4

C36 4 4

C48 6 6

C60 6 6

C72 6 6

Installation of Legs/Casters:

1. Carefully tip range on its side.

2. Align holes in leg/caster mounting plate with pre-drilled holes in bottom of range located in each of

the four corners. Two additional legs/casters must be installed on the C48, C60, and C72. The

additional legs/casters should be installed utilizing the pre-drilled holes shown in Figure 1.

Figure 1 - Cross Chassis Leg/Caster Mounting

3. Attach mounting plate to bottom of range using four ¼ - 20 x ⅝“ self tapping screws (provided). If

casters are being installed, the locking casters should be mounted on the front.

4. After all legs/casters have been installed, carefully return the range to its upright position.

(For additional leg information, see Leveling section of this manual).

Ranges mounted on casters must use a flexible connector (not supplied by Wolf) that complies with the

Standard for Connectors for Movable Gas Appliances, ANSI Z21.69•CSA 6.16 and a quick-disconnect

device that complies with the Standard for Quick-Disconnect Devices for Use With Gas Fuel, ANSI

Z21.41•CSA 6.9. In addition, adequate means must be provided to limit movement of the appliance

without depending on the connector and the quick-disconnect device or its associated piping to limit

appliance movement. Attach the restraining device at the rear of the range.

- 5 -

If disconnection of the restraint is necessary, turn off the gas supply before disconnection. Reconnect

this restraint prior to turning the gas supply on and returning the range to its installation position.

If the range is installed on casters and is moved for any reason, it is recommended that the range be

re-leveled front to back and side to side for even baking.

LEVELING

To level the range, place a carpenter's level on the range top and check leveling of the unit side to side

and front to rear. Achieve leveling by turning each foot section of the unit's leg as needed. Turning the

foot in a counter clockwise direction will increase height and clockwise will decrease.

GAS PRESSURE REGULATOR

A preset gas pressure regulator and street elbow is shipped with the range. This regulator must be

installed by an authorized service person before the unit is placed into operation. See full unit data plate

located on the rear of the range, or the secondary data plate, riveted to the kick panel, for pressure

regulator setting information. If a manometer is being used, utilizing one of the available pressure taps

in the manifold, the manifold pressure with one burner on should be ± 0.3" W.C. of the value indicated

on the rating plate.

1. Locate the gas connection pipe protruding through the back of the unit.

2. Cover the pipe threads with pipe joint compound resistant to propane gases.

3. Screw the regulator onto the pipe hand tight with flow direction arrow pointing towards the back of

the unit and the regulator adjustment in the up right position.

4. With a pipe wrench, tighten the regulator securely in the upright position. (The regulator is preset

and should not require any additional adjustments.) The pressure regulator must be mounted

horizontally to ensure the proper preset outlet pressure. If mounted in any other direction, the outlet

pressure must be rechecked and possibly reset. A leak limiter is supplied with every regulator to

allow excess gas pressure to escape. Do not obstruct the limiter or the gas regulator, as obstruction

may cause the regulator to malfunction.

GAS CONNECTIONS

All gas supply connections and any pipe joint compound used must be resistant to the action

of propane gases.

Prior to lighting, check all joints in the gas supply line for leaks. Use soap and

water solution. Do not use an open flame.

After piping has been checked for leaks, all piping receiving gas should be fully purged to remove air.

TESTING THE GAS SUPPLY SYSTEM

When test pressures exceed ½ psig (3.45 kPa), the range and its individual shutoff valve must be

disconnected from the gas supply piping system.

When test pressures are ½ psig (3.45 kPa) or less, the range must be isolated from the gas supply

system by closing its individual manual shutoff valve.

- 6 -

FLUE CONNECTIONS

DO NOT obstruct the flow of flue gases from the flue located on the rear of the range. Proper venting

of flue gas is vital to the safe and efficient operation of the range. Problems arising from the intentional

obstruction of the flue will result in voiding of warranty. It is recommended that the flue gases be

ventilated to the outside of the building through a ventilation system installed by qualified personnel.

From the termination of the flue to the filters of the hood venting system, a minimum clearance of 18"

(457 mm) must be maintained. Information on the construction and installation of ventilating hoods

may be obtained from the standard for "Vapor Removal from Cooking Equipment," NFPA No. 96 (latest

edition), available from the National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

ELECTRICAL CONNECTIONS

Electrical and grounding connections must comply with the applicable portions

of the National Electrical Code and/or other local electrical codes.

Disconnect the electrical power to the machine and follow Lockout / Tagout

procedures.

Appliances equipped with a flexible electrical supply cord are provided with a

three-prong grounding plug. It is imperative that this plug be connected into a properly

grounded three-prong receptacle. If the receptacle is not the proper grounding type, contact an

electrician. Do not remove the grounding prong from this plug.

The convection range is designed for 120 volt power supply and is provided with a flexible electric

supply cord and plug that must be plugged into the proper receptacle. Do not connect the convection

range to electrical supply until after gas connections have been made. The wiring diagram for the

convection range is located on the rear of the appliance.

OPERATION

The appliance and its parts are hot. Use care when operating, cleaning, or

servicing the appliance.

CONTROLS

Open Top Burner Valve — Allows gas to flow to the top burners. To open valve, turn knob

counterclockwise. To close valve, turn knob clockwise.

Manual Griddle Valve — Allows gas to flow to the griddle burners. To open valve, turn knob

counterclockwise. To close valve, turn knob clockwise.

Oven Thermostat — Regulates oven temperature. The thermostat temperature range is from LOW at

approximately 250°F (121°C) to HI at approximately 500°F (260°C). Turn the thermostat

counterclockwise to increase temperature and clockwise to decrease temperature. Oven temperature

regulation is the most accurate between 300°F (149°C) and 500°F (260°C).

- 7 -

Griddle Thermostat — Regulates griddle temperature. The thermostat temperature range is from

LOW at approximately 200°F (93°C) to HI at approximately 550°F (288°C). Turn the thermostat

clockwise to increase temperature and counterclockwise to decrease temperature.

Safety Valve – Monitors standing pilot. The oven and thermostatic griddle feature a standing pilot that

must be manually lit. The pilot is monitored by a thermocouple and pilot safety valve. If the pilot goes

out, the safety valve will shut-off the gas supply to the pilot and main burners.

Fan Switch – Turns fan on and off (Convection Ovens only). Fan turns on when door is closed. Fan

turns off when door is opened.

BEFORE FIRST USE

Ovens

New ovens require a burn off period to break in the oven and eliminate unappetizing odors from

penetrating the food product. These odors are typically from curing of the porcelain enamel oven cavity

parts.

Turn on gas to unit and set the thermostat to 475°F (246°C). Allow the oven to operate at this

temperature for 30 to 45 minutes.

Griddles

Before leaving the factory the griddle is coated with vegetable oil as a rust inhibitor. Remove this film

when the griddle plate is being cleaned prior to its first cooking use. Heat the griddle to 200-300°F to

loosen and melt the coating, then clean the surface with a non-corrosive, grease dissolving commercial

cleaner, following the manufacturer’s directions. Rinse thoroughly and wipe dry with a soft clean cloth.

Clean all accessories.

The griddle plate is steel, but the surface is soft and can be scored or dented by

careless use of spatulas or scrappers. Be careful not to dent, scratch or gouge the plate. Do

not try to knock off loose food that may be on the spatula by tapping the corner edge of the

spatula on the griddle surface.

Season the griddle to avoid possible surface corrosion before first use, and after every cleaning. Heat

griddle to a low temperature (300-350°F) and apply a small amount of cooking oil – about one ounce

per square foot of surface. Use a soft lint-free cloth to spread the oil over the entire griddle surface to

create a thin film. Wipe off any excess oil with a cloth. Repeat the procedure until the griddle has a

slick, mirror-like finish.

LIGHTING AND SHUTTING DOWN PILOTS

TOP SECTIONS

Open Top, Manual Griddle

1. Remove front row of grates (Open Top Only).

2. Turn the main gas supply valve to the ON position.

3. Light all standing pilots.

Open Top - Pilot access can be reached under the grate support beam running from left to right.

Manual Griddle – Pilot access can be reached under the griddle plate through the slotted opening in

the manifold cover near the burner valve knob.

- 8 -

- 9 -

4. Turn the burner valve ON to the desired heat.

5. If burners fail to light, turn off all valves, and then call an authorized installation or service person.

6. To shut down, turn the burner valve to the OFF position.

7. For complete shut down, turn all burner valves to the OFF position. Turn off main gas supply.

Thermostatic Griddle

1. Turn the thermostat to the OFF position.

2. Turn the main gas supply valve to the ON position.

3. Depress and hold the red button on the safety valve and light the pilot through the slotted opening

in the manifold cover near the burner valve knob.

4. Hold red button down for at least 30 seconds.

5. When button is released, pilot should remain lit.

6. Pilot flame must be high enough to heat thermocouple.

7. Turn thermostat to desired temperature setting.

8. If ignition fails, turn the control knob to OFF. Wait 5 minutes and repeat the above procedure.

DO NOT attempt to relight pilot without waiting 5 minutes.

9. For temporary or nightly shutdown, turn control knob to OFF position.

10. For complete shutdown, turn control knob to OFF position, and turn off main gas supply.

OVEN SECTION

- Standard Oven with Standing Pilot, Convection Oven with Standing Pilot

1. Turn thermostat to OFF position.

2. Turn the main gas supply valve to the ON position.

3. Lift up on louvered kick panel and rotate down 90°.

4. Depress red button on safety valve and light pilot through opening in burner box area.

5. Hold red button down for at least 30 seconds.

6. When button is released, pilot should remain lit.

7. Pilot flame must be high enough to heat thermocouple.

8. Return louvered kick panel to original position.

9. Convection Oven – Turn on fan switch located between oven control knob and pilot safety valve.

10. Turn thermostat to desired temperature setting.

- 10 -

11. Standard Oven – If ignition fails, turn the oven control knob to OFF. Wait 5 minutes and repeat the

above procedure.

Convection Oven – If ignition fails, turn the fan switch and oven control knob to OFF. Wait 5

minutes and repeat the above procedure.

DO NOT attempt to relight pilot without waiting 5 minutes.

12. Standard Oven – For temporary or nightly shutdown, turn oven control knob to OFF position.

Convection Oven – For temporary or nightly shutdown, turn fan switch and oven control knob to

OFF position.

13. Standard Oven – For complete shutdown, turn oven control knob to OFF position, and turn off main

gas supply.

Convection Oven – For complete shutdown, turn fan switch and oven control knob to OFF position,

and turn off main gas supply.

OPERATING SUGGESTIONS

Open-Top Burners

Open-top burners are quickly lit and require no preheating time. Open top burners have a wide low to

high burner flame adjustment range. This allows for better simmering performance at the lowest

possible stabilized setting. When simmering, turn the burner valve knob down until you reach the

optimum lowest burner flame setting to maintain the desired simmer point.

Manual Griddle

Pre-heat the griddle top for approximately 15 - 20 minutes before cooking. The top can be kept hot with

burners turned partially down. During off periods, turn the burners down or heat only half of the top.

Thermostatic Griddle

Pre-heat the griddle top for approximately 15 - 20 minutes before cooking. The griddle thermostats

regulate temperatures for each 12" section of the griddle from a low setting at approximately 200°F

(93°C) to high setting at approximately 550°F (288°C).

Standard Oven Cooking

Allow time to preheat ovens before using (25 minutes to 400°F [204°C]). The oven thermostat regulates

temperature from a low setting at approximately 250°F (121°C) to high setting at approximately 500°F

(260°C). If properly used, the automatic temperature control is an efficient system. Turn thermostat

down to LOW when oven is idling, or turn the oven control to OFF when not in use.

Moderate oven temperatures will produce better food, reduce shrinkage and keep maintenance costs

down. Using a low temperature for roasting (recommended 325°F [162°C] or lower) will reduce meat

costs by reducing shrinkage.

A pan of water (approximately 12" x 20" x 1" [305 mm x 508 mm x 25.4 mm]) may be placed in the

oven bottom. This water supplies humidity to reduce shrinkage. If necessary, add water during roasting.

Convection Oven Cooking

Cooking time and temperature in convection oven may vary slightly from normal time and temperature.

LOADING AND UNLOADING THE OVEN

Open the door and load the oven as quickly as practical to conserve heat. Take care to avoid spilling

liquids while loading. Close the door and refer to recipe for cooking time.

Provide adequate space for product unloading. Rapid unloading will conserve heat and ensure proper

reheating conditions for the next load, if applicable.

CLEANING

Disconnect the electrical power to the machine and follow Lockout / Tagout

procedures.

Shut off the gas before cleaning the appliance.

The appliance and its parts are hot. Be very careful when operating, cleaning, or

servicing the appliance.

Exterior surfaces may be cleaned using soft cloth and mild detergent. Do not use Dawn

® dish detergent

to clean the exterior or interior components of the range.

Do not use scouring powder. It is extremely difficult to remove completely. It can build up accumulations

that will damage the oven.

Wolf equipment is strongly constructed and is designed to give you long, satisfactory service at low

cost, provided you give it proper care. Frequent cleaning and occasional adjusting should reward you

with low operating and maintenance costs and faster, better service.

DAILY CLEANING

Oven

Remove chrome-plated racks and clean in a sink.

While still warm, wipe top with a soft cloth or other grease absorbing material to remove spillovers,

grease, etc., before they burn in.

Clean oven and oven door daily, especially if fruit pies or tomato sauces were baked, meats roasted,

and if there have been spillovers.

After processing some foods at low temperatures, odors may linger in the oven. These odors may be

cleared by setting the thermostat at 500°F (260°C) and allowing the oven to operate unloaded for 30 to

45 minutes.

Open Top

Clean cast iron open top grates with a mild soap and water solution. Rinse thoroughly and dry with a

clean, water-absorbent towel. Immediately after drying (with grates still removed from the range top),

season grates lightly with liquid vegetable or spray-type cooking oil.

After seasoning, replace grates onto the range. Turn on all open top sections to LOW and allow them to

burn for at least 15 minutes before using pots or pans on the range top. Season the open top grates

after each cleaning. Failure to season grates will cause grates to rust.

Griddle Top

Empty the grease drawer as needed throughout the day and regularly clean at least once

daily.

- 11 -

Clean the griddle regularly. A clean griddle always looks better, lasts longer and performs

better. To produce evenly cooked, perfectly browned griddle products keep the griddle

plate clean and free of carbonized grease. Carbonized grease on the surface hinders the

transfer of heat from the griddle surface to the food, resulting in spotty browning and loss

of cooking efficiency. Carbonized grease tends to cling to griddle foods, giving them a

highly unsatisfactory and unappetizing appearance.

After each use, clean the griddle with a Scotch Bright pad or flexible spatula.

Once a day, thoroughly clean the griddle back splash, sides and front. Remove, empty

and wash the grease drawer in the same manner as an ordinary cooking utensil.

EXTERIOR CLEANING

Daily

Clean exterior finish with a mild solution of soap or grease-dissolving cleaner. To remove discoloration,

use a nonabrasive cleaner. Always rub with the grain of the metal. Stainless steel areas of the range

can be polished by using a soft dry cloth. If needed, add stainless steel polish to the soft cloth.

STAINLESS STEEL

Here are a few simple cleaning procedures that have been found effective for keeping stainless steel

equipment clean, sparkling and bright.

General Cleaning

Use ordinary soap or detergent and water for routine cleaning of stainless steel. To prevent water spots

and streaks, rinse thoroughly with warm water and wipe dry with a soft clean cloth. The addition of a

rinsing agent will also help prevent spotting. Do not pressure wash any portion of the range.

Fingerprints

Fingerprints are sometimes a problem on highly polished surfaces of stainless steel. They can be

minimized by applying a cleaner that will leave a thin oily or waxy film. To use these cleaners, simply

wipe on and remove excess with a soft dry cloth. After using, subsequent fingerprints will usually

disappear when wiped lightly with a soft cloth or with a cloth containing a little of the cleaner. If the

surface is especially dirty to start, wash first with soap or detergent and water.

Heat Tint

Straw-colored or slightly darkened areas may appear on stainless steel in and around ovens and

ranges where temperatures reach 500°F (260°C) or more. This "heat tint" is caused by a slight

oxidation of the stainless steel and is not harmful. To control or minimize this condition, never use

more heat than is absolutely necessary.

MAINTENANCE & ADJUSTMENTS

Disconnect the electrical power to the machine and follow Lockout / Tagout

procedures.

LUBRICATION

All moving parts must be checked for wear and lubricated. Contact your local authorized servicer.

Motors in Wolf convection ranges are permanently lubricated and require no additional maintenance.

FLUE

Check the flue when it is cool to be sure it is free of obstructions.

- 12 -

- 13 -

SERVICE AND PARTS INFORMATION

To obtain service and parts information, contact an authorized service agency in your area (refer to our

website, www.wolfrange.com for a complete listing of authorized service and parts depots). When

calling for service, the following information must be available: model number, serial number, and gas

type. This information can be found on the main data plate, located on the rear of the unit, or on the

secondary plate located inside the lower front kick panel. Lift up and lower the front kick panel to view

the secondary data plate.

PRECAUTIONS

When scraping off heavy deposits of grease or oil from stainless steel equipment, never use ordinary

steel scrapers. Particles of ordinary steel may become embedded in, or lodge on, the surface of the

stainless steel. These will rust, causing unsightly stains and possible contamination of food. If it is

necessary to scrape, use stainless steel, wood, plastic or rubber tools.

TROUBLESHOOTING

OVEN

PROBLEM CAUSES / CORRECTIONS

Uneven Baking Side to Side Range not level side to side.

Oven burner or bottom improperly installed.

Wrong temperature setting for product.

Warped pans.

Flue not venting properly.

Improper regulator setting. Contact service provider.

Uneven Baking Front to Rear Range not level front to back.

Door not closing properly.

Flue not venting properly.

Improper regulator setting. Contact service provider.

Too Much Top / Bottom Heat Build-up on side liners obstructing vent holes.

Flue not venting properly.

Dried Out Products Too low temperature (Overcooking).

Too long baking time.

Thermostat calibration (Call for service).

Excessive Meat Shrinkage Roasting Temperature too high.

Not enough moisture (Add pan of water).

Pilot Outage Call for service.

TOP BURNER OPERATION

PROBLEM CAUSES / CORRECTIONS

Excessive Valve Handle Temperatures /

Sticking Top Burner Valves

Verify that oven door is closed.

If door is closed properly, call for service.

Improper ventilation.

Poor Ignition Call for service.

Pilot and Burners Will Not Light Verify that main gas supply is turned on.

Verify that burner assembly is properly installed.

Call for service.

- 14 -

NOTES

FORM F35696 Rev. E (07-08) PRINTED IN THE U.S.A.

MODE D’INSTALLATION ET MODE D’EMPLOI

CUISINIÈRES AU GAZ POUR RESTAURANT

DE LA SÉRIE CHALLENGER XL

MODÈLES:

C24S C36(S,C)

C48(S,C) C48SS

C60(S,C)(S,C) C72(S,C)(S,C)

www.wolfrange.com

Une division de Groupe ITW Équipement alimentaire, LLC

10405 Westlake Drive

Charlotte, NC 28273

DOCUMENT À CONSERVER EN CAS DE BESOIN

F35696 Rév. E (07-08)

MESURES DE SÉCURITÉ IMPORTANTES

CE MANUEL A ÉTÉ PRÉPARÉ À L’INTENTION D’UN PERSONNEL QUALIFIÉ ET AUTORISÉ À

INSTALLER DES APPAREILS FONCTIONNANT AU GAZ ET À EFFECTUER LE DÉMARRAGE

INITIAL CHEZ LE CLIENT DE MÊME QUE LE RÉGLAGE DES APPAREILS CONCERNÉS DANS

CE MANUEL.

AFFICHER À UN ENDROIT VISIBLE LES PREMIERS SOINS À ADMINISTRER À TOUTE

PERSONNE AYANT RESPIRÉ LES GAZ QUE CET APPAREIL DÉGAGE. ON PEUT SE

PROCURER CES INFORMATIONS CHEZ LE FOURNISSEUR DE GAZ LE PLUS PRÈS.

IMPORTANT

En cas d’odeurs de gaz, éteindre l’appareil par le robinet

d’arrêt principal et communiquer avec la compagnie de

gaz la plus près ou avec le fournisseur de gaz attitré pour

l’entretien.

MESURE DE SÉCURITÉ

Ne pas entreposer ni utiliser d’essence ni autres vapeurs

ou liquides inflammables à proximité de cet appareil ou de

tout autre appareil.

L’installation, le réglage, la modification, la réparation ou

l’entretien incorrects de cet appareil peuvent causer des

dommages matériels, des blessures ou la mort. Lire

attentivement les instructions d’installation, de

fonctionnement et d’entretien avant de procéder à son

installation ou entretien.

EN CAS DE PANNE DE COURANT, NE PAS FAIRE

FONCTIONNER CET APPAREIL.

- 2 -

Page is loading ...

Wolf CHALLENGER XL C72SS User manual

Brand: Wolf

Model: CHALLENGER XL C72SS

Category: Fireplaces

Type: User manual

Download PDF

report

in other languages

français: Wolf CHALLENGER XL C72SS Manuel utilisateur

Wolf CHALLENGER XL C72SS User manual

Wolf CHALLENGER XL C72SS User manual

in other languages

Related papers

Other documents