Analog Devices DC371 Quick start guide

Analog Devices
Brand
Analog Devices
Model
DC371
Type
Quick start guide
Quick Start Guide for DC371
By Wei Chen
DC371 is an IMVP2 compatible power supply for powering the Intel mobile Tualatin
processor. The input voltage is 7–21V, the output voltage is programmed by the 5-bit
VID which is compatible with the IMVP2 spec. The circuit is designed to deliver 23A
continuous current. The demo board has an on-board dynamic load tester to facilitate the
dynamic load test.
Quick Start Guide
Refer to Figure 2 for proper measurement equipment setup and follow the procedure
below:
1.
Connect a 21V bench supply to V
IN
and GND pins, a 5V supply to 5V pin and GND
pin, and a 3.3V supply to 3.3V pin and GND. All supplies must be off.
2.
Connect an electronic load to V
CORE
and GND pins using a wire gauge suitable for
23A. Preset load current to 0A.
3.
Initial jumper setup for performance mode operation:
JP7
Short to 5V side
JP11
Short
VID4
VID3
VID2 VID1 VID0
Short Short Open Open Open
DPSLP# VRON DPSLPVR GMUXSEL
Short Open Open Short
4.
Apply 21V, then 5V and 3.3V
5.
Short Jumper VRON. Measure V
CORE
= 1.380 ~ 1.420 V
6.
Apply load current of 23A, measure voltage across C15 to be: 1.288 ~ 1.328V
V
IN
= 21V ± 0.5V, I
IN
< 2A
7.
Change load to 0A
8.
Open Jumper DPSLP#, measure V
CORE
= 1.318~1.358V
9.
Decrease V
IN
from 21V to 14V, change jumpers for battery mode operation:
VID4 VID3 VID2 VID1 VID0
Short Open Open Short Short
DPSLP# VRON DPSLPVR GMUXSEL
Short Short Open Open
Page 1 of 3
10.
Measure V
CORE
= 1.115 ~1.155V
11.
Open Jumper DPSLP#, measure V
CORE
= 1.064 ~ 1.104V
12.
Short Jumper DPRSLPVR, set VID jumpers for deeper sleep mode operation:
VID4 VID3 VID2 VID1 VID0
Open Short Open Short Open
13.
Measure V
CORE
= 0.82~0.88V
14.
Short Jumper GMUXSEL, measure V
CORE
= 0.82~ 0.88V
Dynamic Load Transient Tests
1.
After the output voltage reaches the preset values, apply the load current equal to the
minimum load current of the load step test.
2.
Apply ±12V supplies to +12V, PGND and –12V pins. Then remove jumper JP11.
3.
Use the oscilloscope to test the output step currents from BNC connector “IO”.
Adjust potentiometers R44, R45 and R49 to vary the slew down slope, slew up slope
and step amplitudes (respectively) of the load current change.
4.
Measure the output voltage directly across Cap C15.
While doing the load transient tests, one should make sure that the input bench supply
should have sufficient decoupling capacitance. The following waveform is taken in
the performance mode: V
IN
= 21V, VID = 1.4V, GMUSEL = DPSLP# = 1,
DPRSLPVR = 0. The minimum load current is 8A, and the maximum load current is
23A. The minimum output voltage is 1.30V and the maximum output voltage is
1.39V.
Page 2 of 3
Page 3 of 3
Figure 1. Timing
+
–
+
–
+–
+
–
+
–
+
–
+
–
+
–
+
–
LOAD
+–
21V
5V
3.3V
E1
3.3V
VID4 JP6
VID3 JP5
VID2 JP4
VID1 JP3
VID0 JP2
DPSLP#
VRON
DPRSLPVR
GMUXSEL
E3
5V
JP7
J1
Vin
Inductor
J2
Gnd
J3
Vcore
J4
Gnd
Pwrgood
E2
E4
+12V
+12V –12V
E6
PGND
E5
–12V
Transient Load Tester
Bench Supply
Vin
Vcore
C15
R49
R45 R44
J5
IO
JP11
LTC3714EG
Intel's Notebook Processor
Power Supply
Demo Circuit DC371A
Figure 2. Proper Measurement Equipment Setup
  • Page 1 1
  • Page 2 2
  • Page 3 3

Analog Devices DC371 Quick start guide

Analog Devices
Brand
Analog Devices
Model
DC371
Type
Quick start guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents