ASIX ISP2ZIF User manual

Brand
ASIX
Model
ISP2ZIF
Type
User manual

ASIX ISP2ZIF

ASIX ISP2ZIF is a programming adapter tailored for in-circuit serial programming (ISP) of various devices. It features a ZIF (Zero Insertion Force) socket for easy insertion and removal of devices.

The adapter provides flexibility by allowing users to connect ISP signals (VPP, VDD, GND, DATA, CLK, MISO, and LVP) to any of the device's pins through jumpers. This enables programming of a wide range of devices with varying pin configurations.

With its compatibility with the PRESTO programmer (by ASIX s.r.o.) via the ICSPCAB8 cable, the ISP2ZIF offers a seamless programming experience. It can also be used with other programmers and is suitable for programming Microchip devices as well as other brands.

ASIX ISP2ZIF

ASIX ISP2ZIF is a programming adapter tailored for in-circuit serial programming (ISP) of various devices. It features a ZIF (Zero Insertion Force) socket for easy insertion and removal of devices.

The adapter provides flexibility by allowing users to connect ISP signals (VPP, VDD, GND, DATA, CLK, MISO, and LVP) to any of the device's pins through jumpers. This enables programming of a wide range of devices with varying pin configurations.

With its compatibility with the PRESTO programmer (by ASIX s.r.o.) via the ICSPCAB8 cable, the ISP2ZIF offers a seamless programming experience. It can also be used with other programmers and is suitable for programming Microchip devices as well as other brands.

ISP2ZIF
Programming Adapter
User's Guide
ISP2ZIF
ISP2ZIF is an adapter for programming of all types of devices with in-circuit
serial programming (ISP), especially with the PRESTO programmer (by ASIX
s.r.o.). The adapter is provided with the Zero Insertion Force (ZIF) socket.
Usage
Insert a device to be programmed into the ZIF socket. Use any of two
programming connectors of the adapter to connect the PRESTO programmer
via ICSPCAB8 cable provided with PRESTO. Connect programming signals to
corresponding pins of the device by plugging jumpers to appropriate positions
in the pin array. Any of seven signals of the ISP interface (VPP, VDD, GND,
DATA, CLK, MISO a LVP) can be connected to any of pins of the device. Device
pins are DIP40-like numbered and ISP signals are labeled on the PCB.
Connection is crossed, i.e. layout of the signals of device pins and ISP signals
are routed in lines and columns, respectively. Selected pin is connected to
desired signal by plugging a jumper to the corresponding position.
The adapter is suitable not only for the PRESTO programmer and not only for
Microchip devices. Connection must always be in accordance with ISP
programming requirements (see manufacturer's datasheet). SMD devices can
be programmed with pin converter depending of the device package.
Caution: Incorrect jumper settings can cause damage to the
programmer and the device.
Manufactured by:
Address: ASIX s.r.o., Staropramenna 4, 150 00 Prague, Czech Republic
Phone: +420 257 312 378 Fax: +420 257 329 116
E-Mail: [email protected]
[email protected]
WWW: www.asix.net
ISP2ZIF_MANEN
Copyright © 1991-2011 ASIX s.r.o.
All trademarks used in this document are properties of their respective owners. This
information is provided in the hope that it will be useful, but without any warranty. We
disclaim any liability for the accuracy of this information. We are not responsible for the
contents of web pages referenced by this document.
Appendix: Typical examples of jumper settings for PIC microcontrollers.
Examples are intended for user guidance only (for understanding how the pin
array works). User's connection must always correspond to the device
datasheet.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

ASIX ISP2ZIF User manual

Brand
ASIX
Model
ISP2ZIF
Type
User manual

ASIX ISP2ZIF

ASIX ISP2ZIF is a programming adapter tailored for in-circuit serial programming (ISP) of various devices. It features a ZIF (Zero Insertion Force) socket for easy insertion and removal of devices.

The adapter provides flexibility by allowing users to connect ISP signals (VPP, VDD, GND, DATA, CLK, MISO, and LVP) to any of the device's pins through jumpers. This enables programming of a wide range of devices with varying pin configurations.

With its compatibility with the PRESTO programmer (by ASIX s.r.o.) via the ICSPCAB8 cable, the ISP2ZIF offers a seamless programming experience. It can also be used with other programmers and is suitable for programming Microchip devices as well as other brands.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents