Atlantic Furniture NANTUCKET MURPHY BED Assembly Instructions Manual

Type
Assembly Instructions Manual
Adult assembly
READY
Page 1 of 7
ASSEMBLY INSTRUCTIONS
TWIN
Before assembling your Murphy bed, please read through these
instructions carefully and familiarize yourself with the different parts.
Phillips screwdriver
Customer supplied
HARDWARE
NOTE: WE INCLUDE SPARE HARDWARE IN CASE DAMAGE OCCURS DURING ASSEMBLY.
ATTENTION! If you receive a damaged or defective item,
please contact Atlantic Furniture at [email protected] or 1-800-955-3726
Wood screw 1” - 14 pcs
Spare - 1 pc
B
A
D
C
E
F
I
H
JCB M6 X 25mm - 10 pcs
PO :
Wooden dowel - 10 pcs
Spare - 1 pc
Spare - 1 pc
Wood screw 5/8” - 9 pcs
Spare - 1 pc
Metal pull - 6 pcs
Metal pull screw 25mm - 8 pcs
Allen wrench - 1 pc
Washer - 24pcs
Spare - 1 pc
Spare - 1 pc
Spare - 1 pc
Adjust quantity as needed.
G
Metal pull screw 40mm - 4 pcs
Spare - 1 pc
NANTUCKET MURPHY BED
WITH CHARGING STATION
PARTS LIST
02
01
03
04
05
06
07
08
TOP PANEL
HARDWARE
LEFT SIDE PANEL
RIGHT SIDE PANEL
DOOR
BACK PANEL
DRAWER BASE
FOLDING MATTRESS
01
02
03
03
05
07
08
07
04
04
06
Page 2 of 7
STEP 1
Insert all wooden dowels (A) into the locator holes on (03)(04) and (07) as shown below.
1 BOX
1 BOX
1 BOX
A
A
A
A
Wooden dowel
A
NANTUCKET MURPHY BED
Adult assembly
WITH CHARGING STATION
Adult assembly
Adult assembly
Page 3 of 7
STEP 3
Attach top panel (02) to the side panels as shown below. Using JCB (B), tighten with
Allen wrench (I).
STEP 2
Attach left and right side panels (03) and (04) to the drawer base (07) as shown below.
Using JCB (B) tighten with Allen wrench (I)
07
03
02
04
B
B
B
B
B
B
B B
JCB M6 X 25mm
Allen wrench
B
I
JCB M6 X 25mm
Allen wrench
B
I
NANTUCKET MURPHY BED
WITH CHARGING STATION
Page 4 of 7
Pull out drawer base as shown below. Install metal pull (E) Using metal pull screw (G),
and washers (H). Tighten with Phillips screwdriver (customer supplied).
STEP 4
STEP 5
Install metal pull (E) to the locator holes on (05) as shown below. Using metal
pull screw (F) and washers (H) tighten with Phillips screwdriver (customer supplied).
Back view
05
F
H
H
G
G
G
H
E
E
H
H
G
G
G
F
F
H
H
H
H
E
E
E
E
E
E
F
Metal pull
Metal pull screw
E
F
Phillips screwdriver
Customer supplied
Back view
NANTUCKET MURPHY BED
Adult assembly
WITH CHARGING STATION
Washer
Adjust quantity
as needed
H
Washer
Adjust quantity
as needed
H
Phillips screwdriver
Customer supplied
Metal pull
Metal pull screw
E
G
Adult assembly
STEP 7
Page 5 of 7
Lay the door down flat as shown below. Attach door hinge to drawer base using wood
screw (C) and tighten with Phillips screwdriver (customer supplied ).
Note: Be sure to align door with
side panels in this step.
Wood screw 5/8”
C
Phillips screwdriver
Customer supplied
C
C
C
Lift the door and fold as shown below.
1
Lift the door and latch to side panel as
shown below.
2
STEP 6
NANTUCKET MURPHY BED
Adult assembly
WITH CHARGING STATION
STEP 8
STEP 9
Page 6 of 7
Push the door closed and latch both sides as shown below.
Attach back panel (06) to cabinet assembly as shown below. Using
wood screws (D), tighten with Phillips screwdriver (customer supplied ).
Wood screw
D
Phillips screwdriver
Customer supplied
06
Lock
D
NANTUCKET MURPHY BED
Adult assembly
Adult assembly
WITH CHARGING STATION
STEP 10
STEP 11
Page 7 of 7
Install folding mattress (08) to the bed. Open top panel and push drawer base in as
shown below.
Pull the drawer out fully. Unlatch the door and open, folding down as shown.
Open
Congratulations!
Your Murphy bed is now ready for use.
We recommend that you recheck that all screws are tight,
and that all parts are secure before use to ensure lasting Safety.
08
08
NANTUCKET MURPHY BED
Adult assembly
WITH CHARGING STATION
Adult assembly
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

Atlantic Furniture NANTUCKET MURPHY BED Assembly Instructions Manual

Type
Assembly Instructions Manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI