Hytronik HC038V HCD038 Detached Linear Version RF Wireless Transmission User manual

INSTRUCTION MANUAL FOR RF WIRELESS SENSOR

DETACHED VERSION, MODEL NO.:HC038V / HCD038 + SAM8/RC11 (SAM11) + HC034RF

Technical Specifications

Microwave Motion Sensor

220-240VAC 50Hz/60Hz

5.8GHz CW radar

400W (capacitive load)

Max. 15 devices, Max. 30mA

30° ~ 150°

<0.5W

Max. 12 x 6m

30s ~ 30min.

2 ~ 20Lux; disable

0s, 10s ~ 30min, +

10% ~50%

Indoors, ceiling & wall mounted

-20 ~ +60

PRODUCT TYPE:

OPERATING VOLTAGE:

HF SYSTEM:

RATED LOAD (for HC038V):

OUTPUT (for HCD038):

DETECTION ANGLE:

POWER CONSUMPTION:

DETECTION RANGE (DxH):

HOLD TIME:

DAYLIGHT SENSOR:

STAND-BY PERIOD:

STAND-BY DIMMING LEVEL:

MOUNTING:

WORKING TEMP.:

HC038V

1-10V-

RJ12 connector Push

L’

1-10V+

120

RF antenna

Antenna module

Buzzer

LED indication

Infrared remote receiver

Daylight sensor

Installation hole

Cable entry

32.5

31.2

28.5

19.7

43.3

4.2

52.5

RJ12 connector

DALI

Push

HCD038

Model: SAM11 (RF grouping by rotary switch or remote control HRC-11)

Model: SAM8/RC11 (RF grouping by remote control HRC-11)

4.5

110.5

4.5

13.5

RF antenna

Antenna module Buzzer

LED indication

Rotary switch

Infrared remote receiver

Daylight sensor

Installation hole

57.5

63.6

71.5

4.1

31.7

odel: HC034RF

(

RF receiver can serve as slave onl

, RF

roupin

rotar

switch or remote control HRC-11)

RF antenna

Rotary switch

Infrared remote receiver 1-10V+

1-10V L’ NNL

Installation hole

71.5

4.2

37.5

38.3

11.8

78.2

3rd Floor, block C, complex building, 155#, Bai'gang road south,

Bai'gang village, Xiao Jin Kou town, Huicheng district, Huizhou 516023

Tel:86-752-2772020 F:86-752-2777877

E: [email protected] W:www.hytronik.com

CHINA FACTORY

Room D, 10/f, Tower A, Billion Center, 1 wang Kwong Road,

Kowloon Bay, Kowloon, Hongkong

T: 00852-35197525 F: 00852-30116936

E: [email protected]

HYTRONIK INDUSTRIAL LIMITED

The sensor is an active motion detector; it emits a high-frequency electro-magnetic wave at 5.8GHz and receives its echo. The sensor

detects the change in echo from movement in its detection zone. A microprocessor then triggers the switch light ON command. Detection

is possible through doors, panes of glass and thin walls.

Note: the high-frequency output of this sensor is <0.2mW; approximately just 0.2‰ of the transmission power of a mobile telephone.

IMPORTANT

PLEASE READ THESE INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION AND RETAIN THIS LEAFLET IN A KNOWN

AND SAFE PLACE FOR FUTURE REFERENCE.

SECTION 1 INSTALLATION AND WIRING

1.1 Ensure that the electricity supply is switched off before installing or servicing this product.

1.2 Wiring diagram

HC038V

1-10V +

1-10V

L’

1-10V+

1-10V

LED Driver

1-10V

LED Driver

1-10V

HCD038

DALI

DALI Driver

DALI

Push

HC038V + SAM8/RC11 (SAM11)

HCD038 + SAM8/RC11 (SAM11)

HC034RF

master slave

Use a screwdriver to point

the arrow to the same

channel on both master

and slave.

RF Grouping via Rotary Switch (for SAM11 and HC034RF only)

15 channels are available for fast grouping via rotary switch on the RF

sensor antenna, simply selecting the same channel on each unit, the

grouping is automatically completed.

Noted:channel "0" is not for fast grouping, and sensors can only be

grouped by remote control.

HC034RF

LED Driver

1-10V

SECTION 2 REMOTE CONTROL

Note: the buzzer beeps one time when RC

receives signal successfully

1. Press button “start” to program.

2. Select the buttons in “Detection range”, / “Daylight hreshold”, “Hold time”,

“Stand-by time”, “Stand-by dimming level” to set all parameters.

3. Press button “Memory” to save all the settings programmed in the remote control.

4. Press button “Apply” to set the settings to each sensor unit(s). For example, to pre-set

GHWHFWLRQUDQJHGD\OLJKWWKUHVKROG'LVDEOHKROGWLPHPLQVWDQGE\WLPH

stand-by dimming level 30%, the steps should be as follows: Press button Start,

EXWWRQ'LVDEOH6KLIWPLQ6KLIW0HPRU\%\SRLQWLQJ

to the sensor unit(s) and pressing Apply, all settings are passed on the sensor(s).

Scene prog. [ zone ] (One-key-commissioning)

RESET[ button ]

Press button , all settings go back to the default settings:

Detection range: 100% Hold time: 1min Stand-by period: 5min Stand-by dimming level: 20% Daylight sensor: LUX disable

Shift [ button ]

3UHVVEXWWRQWKH/('RQWKHWRSOHIWFRUQHUZLOOÀDVKWRLQGLFDWHPRGHVHOHFWLRQ

All values / settings in RED are valid for 20 seconds.

Auto Mode [ button ]

Press button to initiate automatic mode. The sensor starts working and all settings remain

as before the light was switched ON/OFF.

Brightness +/- [ button ]

Press button to adjust the light brightness between 10%~100% .

Power output [ button ]

Press button , the light output shifts between 80% and 100%.

Note: the function of “Sensor off” and “Twilight” are disabled.

Permanent ON/OFF [ button ]

Press button ,to select permanent ON or permanent OFF mode.

* Press button / to resume automatic operation.

The mode will change to AUTO Mode after power failure.

2 4

Detection range [ zone ]

Press buttons in zone to set detection range at 100% / 75%/ 50% / 10%.

Note: Disabled for HC034RF.

Daylight threshold [ zone ]

Press buttons in zone to set the daylight sensor at 2Lux / 10Lux / 50Lux / 100Lux / 300Lux

/ 500Lux or Disable.

1RWH7RVHWGD\OLJKWVHQVRUDW/X[/X[/X[SUHVVEXWWRQ6KLIWDW¿UVW

2. Disabled for HC034RF.

Ambient daylight threshold [ button ]

1. Press button Shift, the red LED is on for indication.

2. Press button ,the ambient lux level is sampled and set as the new daylight threshold.

Press buttons in zone to set the hold time at 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min.

1RWH7RVHWKROGWLPHDWVPLQPLQPLQSUHVVEXWWRQ6KLIWDW¿UVW

2. 2s is for testing purpose only, stand-by period and daylight sensor settings are disabled in this mode.

*To exit from Test mode, press button or anybutton in zone .

Hold time [ zone ]

Stand-by time [ zone ]

3UHVVEXWWRQVLQ]RQHWRVHWWKHVWDQGE\SHULRGDWVVPLQPLQPLQPLQK

1RWH³V´PHDQVRQRIIFRQWURO³´PHDQVELOHYHOFRQWURORQZKHQPRWLRQLVGHWHFWHGDQGUHPDLQVDWWKHVWDQGE\GLPPLQJOHYHOZKHQQR

presence is detected after hold-time.

1. HF, PIR, HF+PIR, HF/PIR are disabled.

2. For RF grouping, please see below.

Dual tech & RF mode [ zone ]

Stand-by dimming level [ zone ]

Press buttons in zone to set the stand-by dimming level at 10% /20% / 30% / 50%.

Note: 24h / 12h / 4h / 30s are disabled.

Short press “Learn/Erase” button on RC to activate pairing mode, and the

receiver unit will beep once every second for 3min.

Note: the unit can only pair up to 30 units.

Step1

The receiver unit (slave unit)

%eeper is on for 3min Short press “Learn

/Erase” button

RF grouping

10 11

12 13

83 3 7

10 11 12 13

Semi-auto Mode

[ button & ]

1. Press button Shift (the red LED is on for indication),

2. press button to initiate semi-auto mode. The fixture is manually on by push-switch and

automatically off in semi-auto mode.

HRC-11

II



Step3

The receiver unit (slave unit)

%eeper is on

Erase:

Long press “Learn/Erase” button for 3s to the sensor unit. The beeper rapidly

beeps for about 5s. all commands it has received before will be erased.

SECTION 3 FUNCTION

3.1 Daylight Monitoring Function

Double L N terminal makes it easy for wire loop-in and loop-out, and saves the cost of terminal block and assembly time.

This sensor maybe over-ridden by the end-users to switch on/off the lights manually, or adjust the maximum brightness during motion hold-time with the

push-switch. This makes the product more user-friendly and offers more options to fit for extra-ordinary demands.

* Short push (<1s): on/off function;

ONĺ OFF: the light turns off immediately and cannot be lighten for a certain time (equals to hold time preset) even there is movement is detected. After

this period, the sensor goes back to auto sensor mode.

OFFĺON: the light turns on 100% and goes to auto sensor mode, even when ambient Lux level exceeds the daylight threshold.

Note: when manually push on the master via push switch, it can send a “on” signal to all slaves in the same group. The slaves will turn on when ambient

light is below its daylight threshold preset.

* Long push (>1s): adjust the maximum brightness (between 10% and 100%) during hold-time.

* If no end-user adjustment is desired, simply leave this terminal disconnected.

3.2 Manual Override

3.3 Loop-in and Loop-out Terminal (HC038V & HC034RF)

Hytronik specially designed this function in software for deep energy-saving purpose. A built-in daylight sensor is designed to provide “smart photocell”

function. This function can only be activated when stand-by period is set to “+”. In this mode the lamp will automatically illuminate at the dim level

setting when the natural light goes below the threshold setting. The fixture will also switch off as the natural light returns.

SECTION 4 TROUBLESHOOTING

MALFUNCTION CAUSE REMEDY CAUSE REMEDY

The fixture does not light up

The fixture is always on

The fixture is on when it should not Adjust zone, change installation site

Incorrect daylight threshold setting

Continous movement in the detection zone

Sudden change in temperature due to weather (wind,

rain, snow) or air expelled from fans, or open windows

Faulty fixture

No power supply