Electronic Pulse Massager
HV-F128
■ Thank you for purchasing the OMRON Electronic Pulse
Massager HV-F128.
■ Please read this Instruction Manual thoroughly before using
this unit for the safe and correct use of it.
■ Please keep this Instruction Manual always at hand for your
future reference.
Instruction Manual
INTENSITY
/POWER
SOOTHE
REGION
REPEAT
SPECIAL
MODE
HYPER
TAP
SHLDR
WAIST
JOINT LEG
ARM SOLE
KNEAD
PUSH RUB
SOFT
POINT
W
R
WIDE
MASSAGE
RELIEVE
OFF
POINT
WIDE
ELECTRONIC
PULSE MASSAGER
CONTENTS
Before Using the Unit
Notes on Safety ...............................1
Features of the Product ..................3
Components of the Product ............3
Information on High &
Low-Frequency Therapy ...............4
Names and Functions
of the Parts ...................................5
How to Use
How to Insert the Batteries .............9
How to Connect the Electrode
Cord ............................................... 10
How to Attach the Pad ..................11
Examples of Application ................ 12
How to Treat ..................................13
Treat the region with the
Soothe Button ..........................15
Treat the region with the
Relieve Button .........................16
Treat the region with the
Region Button .......................... 17
Treat the region with the
Massage Button.......................18
After Treatment –Storing the unit ....19
Maintenance
When it is Difficult to Attach
the Pad ........................................ 20
How to Clean and Store the Unit
.......21
Troubleshooting .............................22
Specifications ................................23
HV-F128-AP_C_M08_130221.pdf
1
● The icons and warning signs are indicated here for your safe and correct use of the product as well as to prevent
injuries and/or damage to properties.
● The icons and meanings are as follows:
The icon indicates prohibitions (must not do).
Matters involving certain prohibitions are indicated by text or pictures in or near .
The icon to the left means “Prohibitions to Disassemble”.
The ● icon indicates something that is compulsory (must be observed).
Matters involving certain compulsory actions are indicated by text or pictures in or near ●.
The icon to the left refers to “General compulsory action”.
Examples of Icons
Notes on Safety (Please read this section carefully before using the unit.)
Before Using the Unit
This unit must not be used in combination with the following medical devices:
(1) Internally transplanted electronic medical devices, e.g. pacemakers
(2) Electronic life support equipment, such as respirators
(3) Electronic medical devices attached to the body, such as electrocardiographs
Using this unit with other electronic medical devices may cause erroneous operation of
those devices.
DANGER
Persons with the following conditions must consult the doctor before using this unit.
1) acute disease
2) malignant tumor
3) infectious disease
4) pregnancy
5) cardiac dysfunction
6) high fever
7) abnormal blood pressure
8) skin sensory disorders or skin problems
9) receiving medical treatment, especially those feeling discomfort
May cause an accident or ill health.
Do not use this unit near the heart, above the neck, on the head, around the mouth or on
diseased skin.
May cause an accident or ill health.
Do not use this unit simultaneously with other therapeutic device or in combination with
ointments including spray-type ointments.
May cause discomfort or ill health.
Do not use this unit for purposes other than treatment indicated in this manual.
May lead to accident, trouble, or failure of the unit.
Do not insert the electrode cord plug into any place other than the electrode cord jack of the
main unit.
May cause an electric shock or accident.
Do not disassemble or remodel this unit.
May cause fire, trouble, or accident.
WARNING
If the unit is not functioning properly or you feel discomfort, immediately stop using the unit.
If you feel any trouble with your body or skin, consult the doctor and follow his/her instructions.
If you want to move the Electrode Pad to another region or your body during treatment, be sure
to turn off the power.
If not, you may receive strong electrical shock.
Do not try to attach the Pads to any other person during the treatment.
You may receive strong electrical shock.
Do not start treatment while wearing an electronic device.
The settings and timings of the device may be affected.
Do not use this unit on infants or people not capable of expressing their intensions.
May cause an accident or ill health.
Do not use this unit in places with high humidity such as the bathrooms or while taking a bath
or shower.
You will receive a strong electrical shock.
Do not use this unit while sleeping.
The main unit may develop trouble, or the pad may move to an unexpected region and cause ill
health.
Do not use this unit while driving.
Receiving sudden strong stimulation may lead to traffic accident or trouble.
Do not leave the Electrode Pad attached to the skin after treatment.
Prolonged attachment may cause skin irritation or infection.
Be careful not to allow any metal object, such as belt buckle or necklace come into contact
with the Electrode Pad during treatment.
If not, you will receive a strong electrical shock.
Do not use cellular phones near this unit.
The unit may operate erroneously.
Do not use this unit to treat one region for a long time (more than 30 minutes).
The muscles of the region under treatment may be exhausted and cause poor physical condition.
CAUTION
2
Notes on Safety
3
* 12 Automatic Courses
The device allows you to select your favourite stimulation programme from 12 Automatic Courses for optimized
treatment according to your symptom and needs.
SOOTHE Button
The newly developed program soothes symptom by improving blood circulation when treated over a prolonged
period.
RELIEVE Button
This function provides pain relief with high frequency of 1200 Hz.
REGION Button (6 courses for shoulders, joint, arm, sole, leg (calf), and waist (lower back))
Treats the selected region with pre-programmed courses.
MASSAGE Button (4 courses of Tapping, Kneading, Pushing, and Rubbing)
Allows you to select the massage method according to your needs.
* 5 Special Modes
Allows you to adjust the unit to your favourite stimulations.
Use the Special Modes of “HYPER”, “SOFT”, “REPEAT”, “POINT & WIDE” and “Balance Adjustment (switching
between red and white buttons)” in combination with the Automatic Course to receive treatment in your favourite
stimulation mode.
* Washable and long-lasting Long-Life Pads
* LCD display that shows the selected treatment modes
1. Main unit 2. Type K Electrode Cord
Note: This is a consumable.
3. Long-Life Pad
(to be referred to as “Pad”
hereinafter.)
One set contains two Pads.
Note: These are consumables.
4. Two AAA batteries for trial
use
5. Electrode Holder
6. Soft Fabric Case
7. Instruction Manual
Features of the Product
The following components are included in the box.
If any components are missing, please contact the nearest OMRON dealer.
INTENSITY
/POWER
REGION
REPEAT
SPECIAL
MODE
HYPER
TAP
SHLDR
WAIST
JOINT LEG
ARM SOLE
KNEAD
PUSH RUB
SOFT
POINT
WR
WIDE
MASSAGE
OFF
POINT
WIDE
RELIEVE
SOOTHE
ELECTRONIC
PULSE MASSAGER
Components of the Product
Information on High & Low-Frequency Therapy
4
What is High Frequency?
Effects of high frequency stimulation
High frequency stimulation is for pain relief.
What is Low Frequency?
Effects of low frequency stimulation
Low frequency stimulation is for improving blood circulation.
What is frequency?
Frequency is the number of times electric stimulation is applied to the body per second and is represented by a unit
called Hertz (Hz).
one second
3 stimulation in a second = 3 Hz
100 stimulation in a second = 100 Hz
one second
Standard treatment time
Long-time treatment and strong stimulation cause muscular fatigue and generate adverse effects.
In order to avoid the excessive treatment, Electronic Pulse Massager, model HV-F128 is made to turn off the power
automatically in 15 minutes.
INTENSITY
/POWER
REGION
REPEAT
SPECIAL
MODE
HYPER
TAP
SHLDR
WAIST
JOINT LEG
ARM SOLE
KNEAD
PUSH RUB
SOFT
POINT
WR
WIDE
MASSAGE
OFF
POINT
WIDE
RELIEVE
SOOTHE
ELECTRONIC
PULSE MASSAGER
Main Unit
Electrode Cord Jack
Electrode Cord Plug
Intensity Adjustment/
Power Dial Switch
Turns on and off the power
and adjusts the intensity of
stimulation.
Back of the Main Unit
5
Names and Functions of the Parts
INTENSITY
/POWER
OFF
Battery
Cover
INTENSITY
/POWER
REGION
REPEAT
SPECIAL
MODE
HYPER
TAP
SHLDR
WAIST
JOINT LEG
ARM SOLE
KNEAD
PUSH RUB
SOFT
POINT
WR
WIDE
MASSAGE
OFF
POINT
WIDE
RELIEVE
SOOTHE
ELECTRONIC
PULSE MASSAGER
Tab of the Pad
Hold the Tab to peel off the Pad.
Electrode Cord Plug
Attach the red or the white plug
to each Pad.
Display
Displays the treatment contents.
Description of displays
All the displays illuminate for approximately one second when the power is turned on.
Electrode Cord
Connects the Main Unit with the Pad.
Pad
Attach it to the region you want to be treated.
6
POINT
WIDE
Graphically displays the
approximate frequency to be output.
Displays the remaining
treatment time digitally.
When the Point Button is
pushed, POINT is
highlighted.
When the Wide Button is
pushed, WIDE is
highlighted.
Continued on the following page.
Pad
Attach each Pad to the
region you want to treat.
7
Names and Functions of the Parts
INTENSITY
/POWER
REGION
REPEAT
SPECIAL
MODE
HYPER
TAP
SHLDR
WAIST
JOINT LEG
ARM SOLE
KNEAD
PUSH RUB
SOFT
POINT
WR
WIDE
MASSAGE
OFF
POINT
WIDE
RELIEVE
SOOTHE
ELECTRONIC
PULSE MASSAGER
Select one programme from each course in the treatment, region, and massage
method.
Soothe Button
The unit treats the region with the continuous long-time program*
utilizing low frequency, which is considered to be suitable for the
promotion of blood circulation.
Relieve Button
The program treats the region with high frequency of 1200 Hz,
which helps to relieve pain.
Region Button
The unit treats the selected region with the program.
Massage Button
Select your favourite massage method according to your symptom.
* Continuous long-time program
A program to treat the region with a combination of different
kinds of stimulation for 15 minutes
Automatic Course
8
Hyper Mode
HYPER
The unit provides gradual increase of intensity during treatment.
❇ When you keep on pressing the Hyper Button for several seconds, the unit will start operation in Hyper
Mode.
❇ Since intensive stimulation is applied in this Mode, please be careful not to switch to this Mode
suddenly.
❇ In this Mode, the batteries will wear out faster than in other Modes.
Soft Mode
SOFT The unit provides soft stimulation without giving the feel of irritation.
Repeat Mode
The unit repeats your favourite stimulation.
Point & Wide Mode
POINT
The unit treats the red and the white sides alternately.
WIDE
The unit treats both the red and white sides simultaneously.
❇ Select either the Wide or the Point Button.
When
POINT
is
selected
Emphasis on intensity is
placed upon the red side
while treating both sides
alternately.
Emphasis on intensity is
placed upon the white side
while treating both sides
alternately.
Treats both red and white
sides with the same
intensity alternately.
Emphasis on intensity is
placed upon the red side
while treating both sides
simultaneously.
Emphasis on intensity is
placed upon the white side
while treating both sides
simultaneously.
Treats both red and white
sides with the same
intensity simultaneously.
When
WIDE
is
selected
Balance Adjustment (Switching between red and white buttons)
R
The unit emphasize therapy on the red side.
W
The unit emphasize therapy on the white side.
Selecting Selecting None of Them
You can use this mode when you want to adjust the stimulation to your favourite
programme. This mode can be used in combination with any Automatic Courses.
Special Mode
REPEAT
RSelecting W
1. Turn the Intensity Adjustment/Power Dial Switch to the “OFF” position.
2. Open battery cover on the back of the main unit.
3. Insert batteries according to the polarities shown in the
battery compartment.
4. Close the battery cover.
9
How to Insert the Batteries
How to Use
1.5V LR03
OOOOOO
SIZE'AAA'
1.5V LR03
OOOOOO
SIZE'AAA'
General advice from OMRON on the handling of batteries
• The supplied batteries are for the trial use only and may wear out in less than three months.
• Replace the worn batteries with new ones immediately.
• If you are not going to use the unit for more than three months, remove the batteries.
• If you leave the unit without using it for a long time when the batteries are included inside, leakage from the
batteries may occur leading to trouble.
• Do not use new and worn batteries together or different types of batteries together.
• Insert the batteries with the polarities (+ and –) in correct alignment.
• When handling the batteries, be sure to read the notes on the batteries.
Standard for battery replacement
If you feel the massage stimulation is weak, the batteries may be worn. Replace the batteries with new ones.
10
How to Connect the Electrode Cord
Place the Pad on a flat surface and securely connect the Electrode Cord Plug
with the Pad.
❇ Although Electrode Cord Plugs are provided in red and white, either plug can
be connected with one of the Pads irrespective of color.
General advice from OMRON on the handling of Electrode Cord
• Avoid excessive bending and pulling of the Electrode Cord.
• Hold the Electrode Cord Plug when unplugging the Electrode Cord from the Main Unit.
• If the Electrode Cord is torn or in trouble, please contact the store where you purchased the unit or at the
nearest OMRON dealer.
1. Turn the Intensity Adjustment/Power Dial Switch to
the “OFF” position.
2. Connect the Electrode Cord with the Main Unit.
Insert the Electrode Cord Plug into the Electrode Cord Jack.
3. Connect the Electrode Cord to the Pad.
When using the unit for the first time
Take out the Pads from the clear plastic bag.
❇ Do not peel off the clear film attached to the Pad at this time.
11
How to Attach the Pad
Attach each Pad to the region you want to treat without bending it.
When you use the unit for the first time:
A clear plastic film is attached to the Pad.
As the Pad has strong adhesiveness, peel off the clear plastic film from the
Pad and attach the Pad to the region you want to receive treatment.
❇ Discard the peeled off clear film as it should not be used anymore.
❇ It may be difficult for you to attach the Pad on your back such as shoulders or waist
(lower back). It is a good idea to ask someone in your family to help you.
Attach the Pad close to the skin.
❇ If the Pad comes off from the skin, the unit is turned off automatically in approximately 7 seconds.
General Advice from OMRON on the handling of Pad
• Do not place pads one on top of the other.
• Do not bend the Pad.
• Do not touch the adhesive surface with your fingers.
• When you perspire after taking a bath or immediately after exercising, wipe your sweat off the region you
want to treat before using the unit.
• Do not apply the Pad to areas you have treated with a deodorant sheet to suppress sweating or spray. The
adhesion of the Pad may be weakened.
• If the Pad is erroneously adhered to a cloth or so and does not come off easily, do not force to peel it off.
Instead, moisten the back of the cloth to which the Pad is attached with a small amount of water, and then
the Pad will come off easily.
• When the adhesive property of Pad drops, take appropriate measures as necessary. (Refer to page 20.)
• If you are going to use a wet Pad or the Pad immediately after it is washed, let it dry sufficiently. Especially
let the adhesive surface air-dry.
13
How to Treat
This section explains the treatment procedure and the entire operation flow from turning on the power
to storing of the unit.
Four treatment methods are available. Select your favourite one to receive treatment.
– Treat with the Soothe Button
When you want to improve blood circulation.
– Treat with the Relieve Button
When you want to relieve pain.
– Treat with the Region Button
When you want to treat the selected region of shoulder, joint, arm, sole, leg (calf), and waist (lower back) with
the program.
– Treat with the Massage Button
When you want to treat the region according to your symptom and favourite operation by selecting the
massage method from Tapping, Kneading, Pushing, and Rubbing.
Have you connected the Electrode Cord? (Refer to Page 10.)
Have you attached the Pads to the regions you want to receive treatment? (Refer to Page 11.)
1. Turn on the power.
Rotate the Intensity Adjustment/Power Dial Switch downwards.
When you hear a click, the power is turned on and the treatment
starts.
❇ When you use the unit for the first time, the Shoulder light will flash
and WIDE will be displayed. When you use the unit for the second
time and after, the Buttons you used in the previous treatment will
flash (except for the Hyper Mode.)
2. Select one treatment method.
– Treat with the Soothe Button (Refer to Page 15.)
– Treat with the Relieve Button (Refer to Page 16.)
– Treat with the Region Button (Refer to Page 17.)
– Treat with the Massage Button (Refer to Page 18.)
Click
INTENSITY
/POWER
REGION
REPEAT
SPECIAL
MODE
HYPER
TAP
SHLDR
WAIST
JOINT LEG
ARM SOLE
KNEAD
PUSH RUB
SOFT
POINT
WR
WIDE
MASSAGE
OFF
POINT
WIDE
RELIEVE
SOOTHE
ELECTRONIC
PULSE MASSAGER
If the Pads come off:
If the Pads come off from the skin, the power will be turned off
automatically in approximately 7 seconds. Turn the Power to OFF,
then re-attach the Pads correctly and turn on the power again.
14
3. Adjust the intensity of stimulation.
Select your favorite intensity level from 1 to 10 by rotating the
Intensity Adjustment/Power Dial Switch.
Standard for treatment
Duration: 10 to 15 minutes per region for each time
Number of treatment times: Once or twice in a day
Intensity: As much as you feel comfortable when using this unit
INTENSITY
/POWER
REGION
REPEAT
SPECIAL
MODE
HYPER
TAP
SHLDR
JOINT
ARM SOLE
KNEAD
PUSH RUB
SOFT
POINT
WR
WIDE
MASSAGE
1
POINT
WIDE
RELIEVE
SOOTHE
ELECTRONIC
PULSE MASSAGER
WAIST
LEG
4. When the treatment ends, turn off the power.
Rotate the Intensity Adjustment/Power Dial Switch upwards. When
you hear a click, the power is turned off.
❇ The power will be turned off automatically in approximately 15
minutes after the treatment starts. Even when the power is turned
off automatically, turn off the Intensity Adjustment/Power Dial
Switch. Otherwise, the batteries will wear out slightly faster.
5. Store the unit.
❇ If you leave the Pads as they are, they will become dirty or the
adhesiveness will deteriorate. When the treatment ends, attach
the Pads to the Electrode Holder for storage.
(Refer to Page 19.)
INTENSITY
/POWER
REGION
REPEAT
SPECIAL
MODE
HYPER
TAP
SHLDR
JOINT
ARM SOLE
KNEAD
PUSH RUB
SOFT
POINT
WR
WIDE
MASSAGE
OFF
POINT
WIDE
Click
RELIEVE
SOOTHE
ELECTRONIC
PULSE MASSAGER
WAIST
LEG
Continued on the following page.
How to Treat Treat the region by selecting one course from Soothe, Relieve, Region, and Massage.
15
Treat the region with the
SOOTHE
Button
When you want to improve blood circulation.
1. Push the Soothe Button.
The unit treats the region with a combination of different stimulation
for 15 minutes using low-frequency stimulation known to be suitable
in promoting blood circulation, unlike traditional program using
repeated stimulation of short cycles.
In this treatment, you will not get bored or become addicted to the
treatment even if the treatment is given over long period.
❇ When you use the unit for the first time, the Shoulder light will flash
and WIDE will be displayed. When you use the unit for the second
time and onward, the Button you used in the previous treatment
will flash (except for the Hyper Mode.)
❇ The Button you have selected will be flashing.
INTENSITY
/POWER
REGION
TAP
SHLDR
WAIST
JOINT LEG
ARM SOLE
KNEAD
PUSH RUB
MASSAGE
OFF
POINT
WIDE
RELIEVE
SOOTHE
SOOTHE
How to use the Special Mode
You can use this Mode when you want to
adjust the stimulation to your favourite
programme.
You can use this Mode in combination with all
Automatic Courses.
❇ The Button you have selected will be
flashing.
❇ To stop the function you selected, push the
Button again.
If you want to increase intensity of
stimulation;
Use the Hyper Mode.
HYPER
The unit provides gradual increase of intensity
during treatment.
❇ When you keep on pressing the Hyper Button for several
seconds, the unit will start operation in Hyper Mode.
❇ Since intensive stimulation is applied in this Mode, please
be careful not to switch to this Mode suddenly.
❇ In this Mode, the batteries will wear out faster than in
other Modes.
If you do not like the feel of irritation:
Use the Soft Mode.
SOFT The unit provides soft stimulations
without giving the feel of irritation.
▼
▼
INTENSITY
/POWER
REGION
TAP
SHLDR
WAIST
JOINT LEG
ARM SOLE
KNEAD
PUSH RUB
MASSAGE
OFF
POINT
WIDE
RELIEVE
SOOTHE
RELIEVE
16
Treat the region with the
RELIEVE
Button
When you want to relieve pain
1. Push the Relieve Button.
This is a program using high-frequency stimulation of 1200 Hz, which
is said for pain relief.
With the use of various stimulations of 1200 Hz frequency, you will
not get bored or become addicted to the treatment. This method is
suitable for pain relief.
❇ When you use the unit for the first time, the Shoulder light will flash
and WIDE will be displayed. When you use the unit for the second
time and after, the Button you used in the previous treatment will
flash (except for the Hyper Mode.)
❇ The Button you have selected will be flashing.
If you want to repeatedly use only your favourite stimulation:
Use the Repeat Mode.
The unit repeats your favourite stimulation.
If you want to massage intensively and fully:
Select the Point Mode.
If you want to massage a wide range of the region such as the waist (lower back):
Select the Wide Mode.
If you want to use different kinds of stimulation for the right and left sides:
Select red or white Button.
SPECIAL
MODE
POINT
WR
WIDE
Point & Wide Mode, Balance Adjustment (Switching between Red and White Buttons)
The stimulation of each Pad varies.
(For detail use of this Mode, refer to Page 8.)
Continued on the following page.
▼▼▼▼
REPEAT
How to use the Special Mode
You can use this Mode when you want to
adjust the stimulation to your favourite
programme.
You can use this Mode in combination with all
Automatic Courses.
❇ The Button you have selected will be
flashing.
❇ When you want to stop the function you
selected, push the Button again.
If you want to increase intensity of
stimulation;
Use the Hyper Mode.
HYPER
The unit provides gradual increase of intensity
during treatment.
❇ When you keep on pressing the Hyper Button for
several seconds, the unit will start operation in
Hyper Mode.
❇ Since intensive stimulation is applied in this Mode, please
be careful not to switch to this Mode suddenly.
❇ In this Mode, the batteries will wear out faster than in
other Modes.
If you do not like the feel of irritation:
Use the Soft Mode.
SOFT The unit provides soft stimulations
without giving the feel of irritation.
INTENSITY
/POWER
REGION
TAP
SHLDR
WAIST
JOINT LEG
ARM SOLE
KNEAD
PUSH RUB
MASSAGE
OFF
POINT
WIDE
RELIEVE
SOOTHE
REGION
SHLDR
WAIST
JOINT LEG
ARM SOLE
2. Select the region to which the Pads are attached.
For example, if you attach the Pads to your shoulders, select
Shoulder. The unit treats you with the program for Shoulder.
❇ The Button you have selected will be flashing.
1. Push the Region Button.
Each time you push the Region Button, the display flashes in the order
of Shoulder, Joint, Arm, Sole, Leg (calf), and Waist (lower back).
❇ When you use the unit for the first time, the Shoulder light will flash
and WIDE will be displayed. When you use the unit for the second
time and after, the Button you used in the previous treatment will
flash (except for the Hyper Mode.)
17
How to Treat
Treat the region with the
REGION
Button
When you want to treat the selected region of shoulder, joint, arm, sole, leg (calf) and waist (lower back)
to which the Pads are attached with the program
When Shoulder is selected
Treat the region by selecting one course from Soothe, Relieve, Region, and Massage.
▼
▼
If you want to repeatedly use only your favourite stimulation:
Use the Repeat Mode.
REPEAT
The unit repeats your favourite stimulation.
If you want to massage intensively and fully:
Select the Point Mode.
If you want to massage a wide range of the region such as the waist (lower back):
Select the Wide Mode.
If you want to use different kinds of stimulation for the right and left sides:
Select red or white Button.
SPECIAL
MODE
POINT
WR
WIDE
Point & Wide Mode, Balance Adjustment (Switching between Red and White Buttons)
The stimulation of each Pad varies.
(For detail use of this Mode, refer to Page 8.)
INTENSITY
/POWER
REGION
TAP
SHLDR
WAIST
JOINT LEG
ARM SOLE
KNEAD
PUSH RUB
MASSAGE
OFF
POINT
WIDE
RELIEVE
SOOTHE
MASSAGE
TAP
KNEAD
PUSH RUB
18
Treat the region with the
MASSAGE
Button
When you want to treat the region according to your symptom and favourite operation by selecting the
massage method from Tapping, Kneading, Pushing, and Rubbing
1. Push the Massage Button.
Each time you push the Massage Button, the massage method
flashes in the order of Tapping, Kneading, Pushing, and Rubbing.
❇ When you use the unit for the first time, a Shoulder Button will flash
and WIDE will be displayed. When you use the unit for the second
time and onward, the Button you used in the previous treatment
will flash (except for the Hyper Mode.)
2. Select your favourite massage method according to
your symptom.
The massage type changes automatically as you select it.
❇ The Button you have selected will be flashing.
▼
▼▼▼
When Tapping is selected
19
After Treatment – Storing the unit
If you leave the Pads without taking care of them, they will become dirty or the adhesive property will
drop. When the treatment ends, attach the Pads to the Electrode Holder and store them.
1. Turn off the Power and remove the Electrode Cord
Plug from the Main Unit.
4. Bundle the Electrode Cord and wrap it around the
Electrode Holder.
❇ Wrap the Electrode Cord loosely.
INTENSITY
/POWER
REGION
REPEAT
SPECIAL
MODE
HYPER
TAP
SHLDR
WAIST
JOINT LEG
ARM SOLE
KNEAD
PUSH RUB
SOFT
POINT
WR
WIDE
MASSAGE
OFF
POINT
WIDE
RELIEVE
SOOTHE
ELECTRONIC
PULSE MASSAGER
5. Store the Main Unit and the Electrode Holder in the
Soft Fabric Case.
3. Lightly attach the Pad to the Electrode Holder
❇ You may leave the Electrode Cord connected with the Pad as it is.
❇ Do not press the Pad hard to the Electrode Holder. It may cause
the adhesive surface to be damaged.
❇ Keep the Electrode Holder clean.
2. Peel off the Pad.
❇ Hold the Tab to peel off the Pad without touching the adhesive
surface.
Example: When the Pad is attached
to shoulder
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/
