Pepperl+Fuchs BW2087 Owner's manual
- Category
- Interface cards/adapters
- Type
- Owner's manual
AS-i 3.0 PCI Board, AS-i 3.0 Compact PCI Board
Operating Manual
...supports all functions acc. to the AS-i Specifications 2.04, 2.1 and 3.0
Edition: 19.6.08
Subject to modifications.
Reproduction, duplication and/or translation is not
permitted.
The nomination of goods usually takes place in this
work without mention of existing patents, utility
models or registered trade marks.
The absence of such a reference does not justify
the acceptance, a commodity is free.
© Bihl+Wiedemann GmbH
Floßwörthstr. 41
D-68199 Mannheim
AS-i 3.0 PCI Board Table of Contents
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
1
Table of Contents
AS-i 3.0 PCI Board, AS-i 3.0 Compact PCI Board
Declaration of Conformity ........................................................................ 5
1 Introduction ........................................................................................................ 6
1.1 General .............................................................................................................6
1.2 Safety and accident prevention .........................................................................6
1.3 Structure of the user´s manual ..........................................................................6
1.4 Function of this manual ..................................................................................... 7
1.4.1 Target group ................................................................................................ 7
1.5 Symbols ............................................................................................................7
1.6 Marks ................................................................................................................7
1.7 Notations ...........................................................................................................7
1.8 Terminology ...................................................................................................... 8
1.9 Bihl+Wiedemann hotline ...................................................................................8
2 Safety Precautions ............................................................................................9
2.1 General safety references .................................................................................9
2.2 Adept personnel ................................................................................................ 9
2.2.1 Danger by electricity ..................................................................................10
2.2.2 Structural changes in the equipment .........................................................10
2.2.3 Cleaning and waste management .............................................................10
3 Proper Use ....................................................................................................... 11
3.1 Warranty and liability .......................................................................................11
4 Product Description ........................................................................................ 12
4.1 Range of application .......................................................................................12
4.2 AS-i Specification 3.0 ......................................................................................12
4.3 Scope of supply .............................................................................................. 12
4.4 Accessories .....................................................................................................12
4.5 Particular characteristics ................................................................................. 12
4.5.1 BW1922 .....................................................................................................12
4.5.2 BW2087 .....................................................................................................13
4.5.3 BW1911 .....................................................................................................13
4.5.4 Special characteristic of BW1783, BW2061 ..............................................13
4.5.4.1 BW2061 ...................................................................................................14
4.5.4.2 BW1783 ...................................................................................................14
4.6 Connections and LED indicators .....................................................................15
4.6.1 BW1922, BW2061 ..................................................................................... 15
4.6.2 BW2087 .....................................................................................................15
4.6.3 BW1783, BW1911 ..................................................................................... 16
AS-i 3.0 PCI Board Table of Contents
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
2
4.7 Technical data .................................................................................................17
5 Installation ........................................................................................................18
5.1 Preconditions ...................................................................................................18
5.2 Installation of AS-i 3.0 PCI Boards ..................................................................18
5.2.1 Deinstallation of AS-i 3.0 PCI Boards ........................................................18
5.3 Installation of AS-i 3.0 Compact PCI Boards ...................................................19
5.3.1 Deinstallation of AS-i 3.0 Compact PCI Boards .........................................19
5.4 Connection to one or more AS-i Circuits .........................................................20
5.5 Installing the driver software ............................................................................20
5.6 Deinstalling the driver software .......................................................................20
5.7 Windows device driver and DLLs ....................................................................21
5.8 OPC server ......................................................................................................21
6 Communication via Dual Port RAM (DPRAM) ...............................................22
6.1 DPRAM layout .................................................................................................22
6.1.1 Circuit 1 ......................................................................................................22
6.1.2 Device part 1 ..............................................................................................22
6.1.3 AS-i circuit 2 ...............................................................................................23
6.1.4 Device part 2 ..............................................................................................23
6.1.4.1 Analog data circuit 1 ................................................................................24
6.1.4.2 Analog data circuit 2 ................................................................................24
6.1.4.3 Example: alignment of analog data in DPRAM ........................................24
6.2 DPRAM elements ............................................................................................24
6.2.1 LAS, LDS, LPS, LPF and LOS ...................................................................24
6.2.2 IDI, ODI, PI and PP ....................................................................................25
6.2.3 Execution Control Flags .............................................................................25
6.2.4 Host interface flags ....................................................................................25
6.2.5 Config OK delay .........................................................................................26
6.3 Watchdog enable and Watchdog counter .......................................................26
6.3.1 Interrupt enable ..........................................................................................26
7 Command Interface .........................................................................................28
7.1 Layout ..............................................................................................................28
7.2 Handshake ......................................................................................................28
7.3 The structure of the Legacy Command Interface ............................................29
7.3.1 Description .................................................................................................30
7.3.2 List of all commands ..................................................................................31
7.3.3 Command Interface commands .................................................................32
7.3.3.1 Write Output Data Image ODI ..................................................................32
7.3.3.2 Set Permanent Parameter .......................................................................32
7.3.3.3 Get Permanent Parameter PP .................................................................33
7.3.3.4 Write Parameter .......................................................................................33
7.3.3.5 Store Actual Parameters ..........................................................................34
7.3.3.6 Set Permanent Configuration PCD ..........................................................34
7.3.3.7 Get Permanent Configuration PCD .........................................................35
7.3.3.8 Store Actual Configuration .......................................................................35
7.3.3.9 Read Actual Configuration CDI ................................................................36
7.3.3.10 Set List of Projected Slaves LPS .............................................................36
AS-i 3.0 PCI Board Table of Contents
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
3
7.3.3.11 Set Operation Mode ................................................................................ 37
7.3.3.12 Change Slave Address ............................................................................ 37
7.3.3.13 Execute Command .................................................................................. 38
7.3.3.14 Read Analog Input Data AIDI ..................................................................38
7.3.3.15 Write Analog Output Data Image AODI ...................................................39
7.3.3.16 Read Analog Output Data Image AODI ..................................................39
7.3.3.17 AS-i Control Control ................................................................................ 40
7.3.3.18 Get AS-i Control Status ...........................................................................41
7.3.3.19 Write AS-i Control Flags .......................................................................... 42
7.3.3.20 Read AS-i Control Flags ..........................................................................42
7.3.3.21 Read and Clear List of Corrupted Slaves LCS ........................................43
7.3.3.22 Read and Clear Transmission Error Counters ........................................ 44
7.3.3.23 Set List of Off-line Slaves LOS ................................................................44
7.3.3.24 Rewrite DPRAM ...................................................................................... 45
7.3.3.25 Read and Clear EMC Error Counters ......................................................45
7.3.3.26 Setup EMC Mode ....................................................................................46
7.3.3.27 Perform an AS-i UART Transaction ........................................................47
8 PCI Device ........................................................................................................ 48
8.1 Announcement ................................................................................................48
8.2 Identification ....................................................................................................48
8.3 Resources .......................................................................................................48
8.4 Register ...........................................................................................................48
8.4.1 Interrupt Event Register ............................................................................. 48
8.4.2 Subsystem Reset Register ........................................................................49
8.4.3 Interrupt Hold–Off Register ........................................................................ 49
9 Commissioning Tools and Accessories .......................................................50
9.1 Windows software AS-i Control Tools ............................................................. 50
9.2 Accessories .....................................................................................................53
9.2.1 Analyser .....................................................................................................53
9.2.2 Network extension ..................................................................................... 53
9.2.2.1 AS-i Repeater IP20 .................................................................................53
9.2.2.2 AS-i Repeater IP65 .................................................................................54
9.2.3 Power supplies ........................................................................................... 54
9.2.3.1 AS-i Power Supply 4 A ............................................................................54
9.2.3.2 24 V on 30 V AS-i Power Supply in Stainless Steel 2 A .......................... 55
9.2.3.3 4 A/8 A Supply for AS-i Master in Stainless Steel ................................... 55
9.2.3.4 8 A Power supply 3 Phases for AS-i-Master in Stainless Steel ...............56
9.2.3.5 AS-i Power Extender ...............................................................................56
9.3 Further Information ......................................................................................... 56
10 Appendix: Assembly Instructions ................................................................. 57
10.1 Dimensions .....................................................................................................57
10.2 Connections ....................................................................................................58
10.2.1 BW1922, BW2061 ..................................................................................... 58
10.2.2 BW2087 .....................................................................................................58
AS-i 3.0 PCI Board Table of Contents
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
4
10.3 BW1783, BW1911 ...........................................................................................59
10.4 Montage ..........................................................................................................59
10.4.1 BW1922, BW2061 ......................................................................................59
10.5 Accessories .....................................................................................................60
11 We are interested in Your Opinion! ................................................................61
AS-i 3.0 PCI Board Declaration of Conformity
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
5
Declaration of Conformity
according to 89/336/EEC and 73/23/EEC
Bihl+Wiedemann GmbH, Mannheim, Germany, hereby declares under its
sole responsibility that the products mentioned below are in conformity
with the listed harmonized standards or normative documents and (where
neccessary) approved by a competent body.
Manufacturer: Bihl+Wiedemann GmbH
Article-no. Designation
BW1783,
BW1911 AS-i 3.0 Compact PCI Board
BW1922,
BW2087,
BW2061 AS-i 3.0 PCI Board
Applied harmonized standards: EN 50295
EN 61000-6-2
EN 61000-6-4
Applied national standards or
normative documents: Prüfungsordnung für AS-i Master
AS-i 3.0 PCI Board Introduction
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
6
1Introduction
1.1 General
This user‘s manual is supplied with the AS-i 3.0 PCI Board/AS-i 3.0 Compact PCI
Board. It explains function, provides information concerning the correct use, instal-
lation and programming. Before commissioning the AS-i 3.0 PCI Board/AS-i 3.0
Compact PCI Board, you should read the user‘s manual through.
1.2 Safety and accident prevention
AS-i 3.0 PCI Board/AS-i 3.0 Compact PCI Board incorporate the very latest tech-
nology and is absolutely sure to function. Nevertheless rules are to be considered.
1.3 Structure of the user´s manual
This manual consists of 8 chapters.
Chapter 1
„Introduction“ provides general information concerning the user‘s manual.
Chapter 2
„Safety precautions“ provides general rules with respect to the device. Further in-
formation is given for waste disposal.
Chapter 3
„Proper use“ describes the intended use of the equipment.
Chapter 4
„Product description“ describes the main parts of the equipment, gives an over-
view of the options and their application.
Chapter 5
„Installation“ explains the installation of the equipment.
Chapter 6
„Communication via Dual Port RAM (DPRAM)“ explains data exchange via Dual
Port RAM (DPRAM).
Chapter 7
„Command Interface“ explains the functions of the legacy command interface.
Chapter 8
"PCI DEVICE" contains information for announcing the AS-i PCI Board/AS-i Com-
pact PCI Board at a PCI BUS.
Chapter 9
"Commissioning tools and accessories" contains information to start-up the AS-i
PCI board/AS-i Compact PCI board and information to available accessories.
Chapter 10
"Appendix: Assembly instruction" contains assembly instruction.
Chapter 11
"We are interested in Your opinion" Please tell us your opinion to this document.
AS-i 3.0 PCI Board Introduction
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
7
1.4 Function of this manual
This manual instructs for the safe assembly, parameterization of AS-i PCI board/
AS-i Compact PCI board.
This manual does not instructs for the operation of the PC, in which this board is
built in. Please view the manual of the PC for such information.
1.4.1 Target group
This manual is intended for the technical personnel, that integrates the AS-i PCI
board/AS-i Compact PCI board into a PC or configures it.
1.5 Symbols
1.6 Marks
Symbols are used to present the information contained in the user´s manual in a
simple and a clearly organized manner.
• indicates a list of points
⇒ indicates the result of an action
1.7 Notations
CAPITALS indicate commands and instructions/functions.
Italics are used for the requirements necessary to perform an action.
This symbol warns the user of possible danger. Not following this warn-
ing can lead to personal injury or death and/or destruction of the equip-
ment.
This symbol identifies texts which contain operating notes and useful informa-
tion for optimum handling and usage of the device.
This symbol warns the user of a possible failure. Not following this warning
can lead to total failure of the device or any other connected equipment.
AS-i 3.0 PCI Board Introduction
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
8
1.8 Terminology
The following terms and abbreviations are used in the user‘s manual:
AS-i - AS-Interface (Aktuator-Sensor-Interface)
PC - Personal Computer
Board - PCI board and/or Compact PCI board
1.9 Bihl+Wiedemann hotline
If problems or faults occur which you cannot rectify yourself and which are not de-
scribed in this user‘s manual, please contact the Bihl+Wiedemann service hotline.
Phone: +49 (0) 621-33 996-0 (Central)
Fax: +49 (0) 621-33 92 22 39
mail: [email protected]
web: www.bihl-wiedemann.com
Please make a note (see lateral label) of the following details before calling
Bihl+Wiedemann GmbH:
Device type:
Art.-no.:
Ident.-no.:
Date of delivery:
AS-i 3.0 PCI Board Safety Precautions
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
9
2 Safety Precautions
This chapter serves for your security and security of the production line users.
2.1 General safety references
2.2 Adept personnel
Adept personnel is someone who:
• was instructed a suitable technical training
• was instructed by the operator of the system -into which the device unit is inte-
grated- about in the operation and the valid safety
• has access to the manual
Please read this chapter carefully, before you work with the device.
The protection of personnel and plant is not ensured, if the device is not used
according to its intended use.
• Another operation than in this guidance the described puts security and func-
tion of the equipment and attached systems at risk.
• The connection of the equipment and maintenance work under tension may
take place only via an electrotechnical specialist.
• If disturbances cannot be eliminated, the equipment is to be set out of opera-
tion and be protected from inadvertent start-up
• Repairs may be accomplished only directly with the manufacturer. Interferenc-
es and changes in the equipment are illegal and make each requirement on
warranty futile.
The responsibility for keeping the locally valid safety regulations is with the
operator.
The device may be installed and taken in operation only by adept personnel!
AS-i 3.0 PCI Board Safety Precautions
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
10
2.2.1 Danger by electricity
2.2.2 Structural changes in the equipment
2.2.3 Cleaning and waste management
• Start all maintenance -, inspection when the unit is disconnected and at zero
potential!
• Attach a danger sign against setting up operation through third persons!
Changes in the element and/or in the provided software are not permitted.
• Handle the used devices and elements properly
• Dispose useless devices and components as special refuse
• Keep the national and local guidelines when disposing of waste materials!
AS-i 3.0 PCI Board Proper Use
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
11
3 Proper Use
The AS-i 3.0 PCI Board/AS-i 3.0 Compact PCI Board is a AS-i Master assembly
group for AT PCs with PCI and/or Compact PCI slots. It realizes the functionality
of two complete AS-i Masters on a PCI Board.
The described devices may only be used in the acceptance of < chapter 4.1 Range
of application >
The devices may only be used at the system, at which they were installed in ac-
cordance with this manual by expert personnel.
3.1 Warranty and liability
Our "General Terms and Conditions of Sale and Delivery" shall apply. They shall
be available to the owner upon conclusion of the contract at the latest.
Only Bihl+Wiedemann GmbH is permitted to issue promisses of warranty.
If defects or damage are repaired by the customer or by the third party without the
prior agreement of Bihl+Wiedemann GmbH, the latter shall refuse all liability for
consequential damage and cannot aknowledge any further warranty claims.
Warranty and liability claims for injury and damage shall be excluded if they are
due to one or more of the following:
• Incorrect use of the unit.
• Inappropriate assembly, commissioning, operation and maintenance of the unit.
• Arbirary modifications to the construction and software.
• Severe damage caused by foreign bodies and force majeure.
With each other use as well as changes of the equipment (also in the context
of assembly and installation) any warranty claim purges opposite the company
Bihl-Wiedemann GmbH.
AS-i 3.0 PCI Board Product Description
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
12
4 Product Description
4.1 Range of application
This operating instruction holds for the following devices of Bihl+Wiedemann
GmbH:
This chapter informs about the special characteristics of the AS-i boards. It de-
scribes the structure and the function of the devices.
4.2 AS-i Specification 3.0
The AS-i 3.0 PCI Board/AS-i 3.0 Compact PCI Board fulfil the new AS-i Specifica-
tion 3.0.
The previous Specifications (2.1 und 2.0) are supported as well.
4.3 Scope of supply
• Driver for Windows 2000/XP
• Driver for Linux
• Documentation
4.4 Accessories
• AS-i Control Tools (BW1203)
4.5 Particular characteristics
4.5.1 BW1922
• 2 AS-i Master on a PCI board
• duplicate address‘ recognition
• integrated earth fault detector
BW1922 AS-i 3.0 PCI Board (double master with duplicate
address´recognition, earth fault/noise detector)
BW2087 AS-i 3.0 Compact PCI-Board (double master without duplicate
address´recognition, without earth fault/noise detector)
BW2061 AS-i 3.0 PCI-Board (programming and test board)
BW1783 AS-i 3.0 Compact PCI-Board (programming and test master)
BW1911 AS-i 3.0 Compact PCI-Board (double master with earth fault/noise
detector)
Please read this chapter before assembling.
AS-i 3.0 PCI Board Product Description
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
13
• integrated noise detector
•PCI interface
• RS 232 diagnostic interface (only in connection with AS-i Control Tools)
4.5.2 BW2087
• 2 AS-i Master on a PCI board
• integrated earth fault detector
• integrated noise detector
• without duplicate address‘ recognition
• without RS 232 diagnostic interface
4.5.3 BW1911
• 2 AS-i Master on a Compact PCI board
• integrated earth fault detector
• integrated noise detector
• Compact PCI interface
• "Plug-and-Play"
4.5.4 Special characteristic of BW1783, BW2061
The board realizes the functionality of 2 complete AS-i masters with AS-i Control
Option as a slot card for the PCI bus and it is characterized by the following char-
acteristics:
• Control the special instructions for EMV test mode and programming
•Data exchange with the PC via Dual Port RAM (DPRAM).
•Constant cycle time:
The board can execute a control program, without influence the power of your
PC. The cycle time of the AS-i PCI Board is independent of PC resources occu-
pied by other programs
•Event control:
An event mechanism can notify the PC application about changes of the data
on the board.
•Interrupt generation on the PCI bus:
For example if the AS-i data changes.
•Breakdown detection:
The board is able to detect a breakdown of the PC, if the watchdog was activat-
ed before (the AS-i master changes into the SAFE MODE, if the Watchdog is
not triggered by the PC program).
•Advanced diagnostics:
The board is able to detect occasionally occurring configuration errors and to
judge the quality of the AS-i communication.
•Multi application:
Simultaneous use of the board with several other applications is possible. The
necessary drivers are contained in the scope of supply.
The board can be operated in 3 different modes:
AS-i 3.0 PCI Board Product Description
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
14
• As a standard AS-i Master according to specification 3.0.
• As a tool for programming of the AS-i Slave ICs SAP4, SAP5, A2SI and ASI4U.
This can be done with the help of Windows programs.
• As a means to perform function and EMC tests which are necessary for every
development of an AS-i slave (EMC test mode).
• The EMC-Test Mode
It is possible to put the Master into a state that is not AS-i compliant. This option
can be useful for specific tests on AS-i under laboratory conditions (e. g. tests with
bursts on the lines or tests with very long wires).
By putting the AS-i Master into the EMC Test Mode it becomes an AS-i test set-up
for experts.
In the test mode, the list of addressed slaves and the telegrams for contacting
these slaves are given by the host. Also, it is possible to decide from within the host
whether faulty answered telegrams from the AS-i Master may be repeated or not
(Note: in regular AS-i operation, data telegrams can be repeated one time). As
above, there are two error counters. However, in this mode the first one counts all
telegrams while the second counts all faulty telegrams.
The AS-i_EMC.EXE program is designed for the operation of the AS-i Master in
the EMC test mode. This program is also delivered as program for Windows.
• Individual software
It is possible to operate the AS-i Master from other hosts with individual software.
The necessary telegrams are described in the manual.
4.5.4.1 BW2061
• PCI interface
• RS 232 diagnostic interface (only in connection with AS-i Control Tools)
4.5.4.2 BW1783
• Compact PCI interface
Fig. 1. User interface of the AS-i EMC Tool
AS-i 3.0 PCI Board Product Description
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
15
4.6 Connections and LED indicators
4.6.1 BW1922, BW2061
4.6.2 BW2087
6 7 8
5
1
2
3
4
[1] RS 232 connection
[2] AS-i circuit 1
[3] AS-i power supply circuit 1
[4] AS-i circuit 2
[5] AS-i power supply circuit 2
[6] PCI connection
[7] LED AS-i 1
[8] LED AS-i 2
5 6 7
4
1
2
3
[1] AS-i circuit 1
[2] AS-i power supply circuit 1
[3] AS-i circuit 2
[4] AS-i power supply circuit 2
[5] PCI connection
[6] LED AS-i 1
[7] LED AS-i 2
AS-i 3.0 PCI Board Product Description
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
16
4.6.3 BW1783, BW1911
1
2
3
4
5 6 7
[1] AS-i circuit 1
[2] AS-i power supply circuit 1
[3] AS-i circuit 2
[4] AS-i power supply circuit 2
[5] LED AS-i 1
[6] LED AS-i 2
[7] PCI connection
AS-i 3.0 PCI Board Product Description
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
17
4.7 Technical data
Technical data
Interface 32 bit PCI bus interface, 3,3 V/5 V
galvanic separation from AS-i
AS-i circuit 1
AS-i circuit 2
Program memory (EEPROM) 4 KB
Operating voltage 3,3 V/5 V DC und AS-i voltage
Operating current approx. 300 mA out of 5 V power supply
approx. 100 mA out 3,3 V power supply
approx. 70 mA out AS-i per AS-i circuit
Voltage of insulation ≥ 500 V
EMC directions EN 61 000-6-2, EN 61 000-6-4
Ambient operating temperature 0°C … +55°C
Storage temperature -25°C … +70°C
AS-i cycle time per AS-i circuit 150 μs*(Number of slaves + 2)
AS-i master profile M4
AS-i specification 3.0
AS-i 3.0 PCI Board Installation
Subject to reasonable modifications due to technical advances Copyright Bihl+Wiedemann, Printed in Germany
Bihl+Wiedemann GmbH · D-68199 Mannheim · Tel. +49-621-339960 · Fax +49-621-3392239 · Internet http://www.bihl-wiedemann.de
Issue date - 19.6.2008
18
5Installation
AS-i 3.0 PCI Board/AS-i 3.0 Compact PCI Board can be installed in the operating
systems Linux, Windows 2000 und Windows XP.
5.1 Preconditions
• IBM compatible PC starting from 80486 (for BW1922, BW2087, BW2061) re-
spectively Compact PCI System (for BW1783, BW1911)
• Administrator rights for the installation routine
⇒ If these conditions are fulfilled, the board can be installed.
5.2 Installation of AS-i 3.0 PCI Boards
• Switch off your computer and any connected devices and unplug the power
supply.
• Loose the screws of the computer housing and open the computer.
• Select a free PCI slot and remove the blanking plate from the top of the slot.
• Insert the board into the slot, connector strip first, until the card is positioned
firmly.
• Screw the PCI board tightly to the top end of the slot.
• Close the computer, screw the housing back together, and plug the power ca-
ble into the socket.
5.2.1 Deinstallation of AS-i 3.0 PCI Boards
In order to demount the AS-i 3.0 PCI Board take steps as described in
<chapter 5.2> last in - first out.
Please read before installation the manual of your computer concerning the
installation of additional hardware components.
Pay attention to the firm seat of the board!
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
Pepperl+Fuchs BW2087 Owner's manual
- Category
- Interface cards/adapters
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Danfoss VLT 5000 (Legacy Product) User guide
-
Kübler Sendix 7188 User manual
-
Aerosoft Iceland X User manual
-
PILZ PMCprimo Drive3 Installation guide
-
Tyco Electronics A1080-A User manual
-
WIKA BLM tag:model:FLM Operating instructions
-
Tyco Electronics A1029-B User manual
-
Tyco Electronics A1030-A User manual
-
-
Adlink VPX3-TL Owner's manual
