Page is loading ...
6900-231-001 New: 06/28/2023
WH3822-WH3375-HC-SO (SHOWN)
Important: Some options may slightly alter installation. To ensure proper installation review the manual
thoroughly and verify rough-ins before beginning any work. File this manual with the owner or maintenance
personnel upon completion of installation.
Industry standard wall backing, for wall hung fixtures, is required. Installer provided wall anchors and wall
anchoring hardware must be appropriate for wall construction.
ANSI, UFAS or ADA compliance is subject to the interpretation and requirements of the local code authority
and is the responsibility of the installer for verification.
Single Temp Valve Assembly: Recommended working water pressure is 30 psi (2.07 bars) minimum to 100
psi (6.89 bars) maximum. Maximum temperature is 130°F (54.4°C). Maximum outlet temperature
recommended is 105°F (40.6°C). Valve assembly must be drained prior to being subjected to freezing
temperatures. A checkstop is provided with this valve assembly.
T/P Mixing Valve Assembly: Recommended working water pressure is 30 psi (2.07 bars) minimum to 100
psi (6.89 bars) maximum. Maximum hot water temperature is 180°F (82°C). Temperature adjustment range
is 85-115°F (29-46°C). Minimum hot water supply temperature must be 5°F (3°C) above desired set
temperature. Valve assembly must be drained prior to being subjected to freezing temperatures. The valve
assembly has checks integral to the inlets however, angle stops are to be provided by the installer.
Prior to installation, supply lines must be flushed of all foreign material such as pipe dope, chips, or solder.
Debris or foreign material in water supply may damage valve.
Teflon tape is recommended on all threaded waste and supply connections to reduce the possibility of leaks.
Provide 110-120VAC/60Hz/3A (MAX) electrical receptacle for optional factory supplied 120VAC/9VDC,
100mA plug-in transformer.
NOTE: Receptacle(s) must be wired to a GFCI protected circuit. Fixture must be earth grounded per N.E.C.
(National Electrical Code).
Model WH3820 Series
®
®
Ligature Resistant Corterra ADA
Compliant Alcove Basin
1
Instructions for Operation and Care of Best-Care WH3820
®
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone (800) 782-7706 • (626) 968-6681 • Fax (626) 855-4862 • Web: www.whitehallmfg.com
ADA
Adult
ADA ages
6 thru 12
ACCESSIBILITY OVERVIEW
OBC
(Ontario Building Code)
CBC
(California Building Code)
34"
(864)
27"
(686)
13
4"
(44)
22"
(589)
15"
(381)
19"
(483) 19"
(483)
12"
(305)
31"
(787)
24"
(610)
22"
(589)
22"
(589)
19"
(483)
15"
(381)
29"
(737)
34"
(864)
19"
(483)
15"
(381)
29"
(737)
34"
(864)
22"
(589)
13
4"
(44)
13
4"
(44)
13
4"
(44)
2
Instructions for Operation and Care of Best-Care WH3820
®
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone (800) 782-7706 • (626) 968-6681 • Fax (626) 855-4862 • Web: www.whitehallmfg.com
DIMENSIONAL DATA
*WIDTH
22"
(559)
WIDTH
*(XL)
CL OF BASIN
*(C1)
CL OF BASIN
*(C2)
CL OF BASIN
*(C3)
CL OF BASIN
*(XR)
CL OF BASIN
*(XL)
CL OF BASIN
*(XR)
CL OF BASIN
FOR PROPER INSTALLATION, INSTALLER MUST
BE PROVIDED WITH SIGNED SUBMITTAL THAT
INDICATES CENTERLINES OF BASIN(S)
22"
(559)
WH3824-BBDB SHOWN, AND WITH WH3375-SO
WH3821-BBED SHOWN, AND WITH WH3375-SO
NOTE: CUSTOMER MUST VERIFY SPECIFIED
DIMENSIONS INDICATED WITH (*) MEET LOCAL
ACCESSIBILITY STANDARDS
DIMENSIONAL LEGEND
KEY DESCRIPTION
XL
CENTER OF FIRST
BOWL FROM LEFT
SIDE OF DECK
C1
CENTER OF FIRST
BOWL TO THE
SECOND BOWL
C3
CENTER OF THIRD
BOWL TO FOURTH
BOWL
XR
CENTER OF LAST
BOWL FROM RIGHT
SIDE OF DECK
C2
CENTER OF
SECOND BOWL TO
THIRD BOWL
DESCRIPTIONKEY
3
Instructions for Operation and Care of Best-Care WH3820
®
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone (800) 782-7706 • (626) 968-6681 • Fax (626) 855-4862 • Web: www.whitehallmfg.com
ROUGH-IN DIMENSIONS -ADA (Adult) And
OBC Ontario Building Code (Canada)
1-1/2" O.D. Tube Lavy Waste Outlet for Compression Joint.
1/2" NPS Hot & Cold Supplies for Angle Stops (By Others).
B
C
D
3/8" x 3-3/8" Mounting Slots (7), Fasteners and Wall Anchors are provided by others. Installer is to use Industry Standards of E
F 120VAC, 60Hz, 3A (Max) GFCI Protected, Electrical Receptacle for Optional Electronically Operated Faucets
to use Industry Standards of Best Practice to suit wall type and construction, weight of fixture and application.
9/16" Diameter Mounting Holes for Mounting Frame, provided. Fasteners and Wall Anchors are provided by others. Installer is A
GENERAL NOTES:
1. All Dimensions Are In Inches (MM)
Industry Standards of Best Practice to suit wall type and construction, weight of fixture and application.
9/16" x 1" Mounting Slots for Mounting Frame, provided. Fasteners and Wall Anchors are provided by others. Installer is to use
161
4"
(413)
34"
(864)
73
8"
(187)
73
8"
(187)
4"
(102)
11"
(279)
7"
(178)
CL OF BASIN C/C
(C1, C2, & C3)
CL OF
BASIN (XL)
CL OF
BASIN (XR)
103
4"
(273)
103
4"
(273)
18"
(457)
223
4"
(578)
303
4"
(781)
73
4"
(197)
4"
(102)
7"
(178)
7"
(178) 161
4"
(413)
271
4"
(692)
29"
(737)
303
4"
(781)
1"
(25)
VIEW FROM FRONT OF FIXTURE
VIEW FROM LEFT SIDE
RIGHT SIDE OPPOSITE
3
4"
(19) 211
4"
(540)
Best Practice to suit wall type and construction, weight of fixture and application.
A
A
A
B
B
A
C
D
EF
G 8-1/4" x 8-1/4" (210 x 210) Optional Faucet Valve mounting area.
G
G
NOTE: MOUNTING PATTERN REPEATS AT EVERY BASIN OR EVERY 25" (635).
32"
(813)
B
IMPORTANT: MODEL WH3822 (2 PERSON) SHOWN FOR REFERENCE ONLY. UNITS ARE PROVIDED TO MATCH SELECTIONS AND
DIMENSIONS PROVIDED BY CUSTOMER. MOUNTING POINTS AND PLUMBING ROUGH-INS ARE TAKEN FROM CENTERLINE OF BASINS.
ADDITIONAL MOUNTING POINTS SIMILAR TO A AND B MAY BE PROVIDED WHEN DIMENSIONS BETWEEN BOWLS ARE LESS THAN
25" (635).
4
!!
Instructions for Operation and Care of Best-Care WH3820
®
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone (800) 782-7706 • (626) 968-6681 • Fax (626) 855-4862 • Web: www.whitehallmfg.com
ROUGH-IN DIMENSIONS -ADA
AGES 6 THRU 12 YEARS
VIEW FROM FRONT OF FIXTURE
GENERAL NOTES:
1. All Dimensions Are In Inches (MM)
31"
(787)
4"
(102)
7"
(178)
7"
(178)
7"
(178) 131
4"
(337)
241
4"
(616)
273
4"
(705)
26"
(660)
VIEW FROM LEFT SIDE
RIGHT SIDE OPPOSITE
1-1/2" O.D. Tube Lavy Waste Outlet for Compression Joint.
1/2" NPS Hot & Cold Supplies for Angle Stops (By Others).
B
C
D
3/8" x 3-3/8" Mounting Slots (7), Fasteners and Wall Anchors are provided by others. Installer is to use Industry Standards of E
F 120VAC, 60Hz, 3A (Max) GFCI Protected, Electrical Receptacle for Optional Electronically Operated Faucets
to use Industry Standards of Best Practice to suit wall type and construction, weight of fixture and application.
9/16" Diameter Mounting Holes for Mounting Frame, provided. Fasteners and Wall Anchors are provided by others. Installer is A
Industry Standards of Best Practice to suit wall type and construction, weight of fixture and application.
9/16" x 1" Mounting Slots for Mounting Frame, provided. Fasteners and Wall Anchors are provided by others. Installer is to use
Best Practice to suit wall type and construction, weight of fixture and application.
G 8-1/4" x 8-1/4" (210 x 210) Optional Faucet Valve mounting area.
B
NOTE: MOUNTING PATTERN REPEATS AT EVERY BASIN OR EVERY 25" (635).
131
4"
(337)
73
8"
(187)
73
8"
(187)
CL OF BASIN C/C
(C1, C2, & C3)
CL OF
BASIN (XL)
CL OF
BASIN (XR)
103
4"
(273)
103
4"
(273)
15"
(381)
193
4"
(502)
273
4"
(705)
73
4"
(197)
4"
(102)
7"
(178)
1"
(25)
3
4"
(19)
181
4"
(464)
A
A
A
B
A
C
D
EF G
G
29"
(737)
B
IMPORTANT: MODEL WH3822 (2 PERSON) SHOWN FOR REFERENCE ONLY. UNITS ARE PROVIDED TO MATCH SELECTIONS AND
DIMENSIONS PROVIDED BY CUSTOMER. MOUNTING POINTS AND PLUMBING ROUGH-INS ARE TAKEN FROM CENTERLINE OF BASINS.
ADDITIONAL MOUNTING POINTS SIMILAR TO A AND B MAY BE PROVIDED WHEN DIMENSIONS BETWEEN BOWLS ARE LESS THAN
25" (635).
5
Instructions for Operation and Care of Best-Care WH3820
®
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone (800) 782-7706 • (626) 968-6681 • Fax (626) 855-4862 • Web: www.whitehallmfg.com
PRE INSTALLATION
Prior to installation remove all large Access Panels 1 from the Frame Assembly 2, by removing the Vandal Resistant
1Fasteners 3. Then swing Panel 1 down then out. Put loose Access Panel(s) 1 in an area where they will not get
damaged.
NOTE: NUMBER OF ACCESS PANELS WILL VARY DEPENDING UPON OVERALL WIDTH OF FIXTURE.
INSTALLATION
With installer provided wall anchors 4 installed per rough-ins, slide Frame Assembly 2 in into position within alcove.
2
NOTE: Some sort of support may be needed to assist in holding
the Frame Assembly in position while securing to wall.
INSTALLER PROVIDE
SUPPORT
2
3
1
3
4
4
2
2
NOTE: Units are designed to suit
Customer specified dimensions.
Approximate weight of fixture PER
36” (914) section/station is 105
pounds (48 KG).
6
Instructions for Operation and Care of Best-Care WH3820
®
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone (800) 782-7706 • (626) 968-6681 • Fax (626) 855-4862 • Web: www.whitehallmfg.com
FRAME ANCHORING
With installer provided wall anchors 4 in place secure Frame Assembly 2 to the rear and side walls using installer
3provided anchoring hardware 5.
5
4
54
2
7
®
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone (800) 782-7706 • (626) 968-6681 • Fax (626) 855-4862 • Web: www.whitehallmfg.com
Instructions for Operation and Care of Best-Care WH3820
Prior to installing the Deck onto Frame Assembly, it is recommenced to install the Grid Strainer and Close
4 Elbow assembly as shown as well as Faucet, see Faucet Installation instructions, link below.
https://www.whitehallmfg.com/uploads/fileLibrary/6900-208-001%20BestCare%20Faucets.pdf
FIXTURE ASSEMBLY
HINT: Teflon tape is recommended on all threaded waste and
supply connections.
WASTE ASSEMBLY
Install Ligature Resistant Strainer to Basin using
A plumbers putty on underside of Grid Strainer
Flange. From beneath Basin, assemble Gasket,
Washer and Jam Nut as shown to Ligature
Resistant Strainer and tighten securely. Add Close
Elbow to Strainer Assembly as indicated.
NOTE: Waste assembly may require field cutting and fitting by the
installer.
À Ligature Resistant Strainer w/ 1-1/2" -16 UNE
Threads
Á Rubber Gasket (1) required
Â1-1/2”-16 Brass Nut
à Flat Fiber Washer (1) required
Ä 1-1/2"-16 x 1-1/4" UNI Close Elbow with
3/8" NPT Clean-Out Plug
Å 1-1/4” O.D. Waste Outlet Connection
NOTE: Waste Assembly may be provided with
Extra items not required in this assembly.
1
2
3
4
5
6
8
Instructions for Operation and Care of Best-Care WH3820
®
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone (800) 782-7706 • (626) 968-6681 • Fax (626) 855-4862 • Web: www.whitehallmfg.com
With Frame Assembly 2 secured to the wall apply a bead of RTV 100 Adhesive 6, provided by installer, to the
5 Frame Assembly Pads 7. With Faucet 8 and Grid Strainer and Close Elbow Assembly 9 installed onto Deck
10, slide Deck 10 into alcove and set onto Frame Assembly 2, ensuring the back of the Deck 10 is against the
back wall and resting on Frame Assembly 2 as shown.
FIXTURE ASSEMBLY
NOTE: Sides of Deck may need to be field sanded/ground
slightly to ensure proper fit within Alcove.
10
8
9
6
7
2
7
6
10 8
6
7
2
9
NOTE: If optional Back and Side Splashes are not selected
apply appropriate Silicone, provided by installer, around
edges of Deck and Wall.
If no Back or Side Splashes continue with valve installation, otherwise continue to next page.
A
https://www.whitehallmfg.com/uploads/fileLibrary/6900-208-001%20BestCare%20Faucets.pdf
9
Instructions for Operation and Care of Best-Care WH3820
®
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone (800) 782-7706 • (626) 968-6681 • Fax (626) 855-4862 • Web: www.whitehallmfg.com
With Deck 10 secured to Frame Assembly 2, apply a bead of adhesive 11 to the walls or the back side of
6 Sidesplashes 12 and Backsplash 13 and set on top of Deck 10 then press and hold against wall until
adhesive sets and they stay in place.
FIXTURE ASSEMBLY
NOTE: Apply appropriate Silicone, provided by installer,
around edges of Back and Side Splashes, Deck, and Wall.
NOTE: Side and Back Splashes may need to be field
sanded/ground slightly to ensure proper fit.
With Back or Side Splashes installed and sealed continue with valve installation.
A
https://www.whitehallmfg.com/uploads/fileLibrary/6900-208-001%20BestCare%20Faucets.pdf
10
11
2
13
12
12
11
10
2
13
11
10
Instructions for Operation and Care of Best-Care WH3820
®
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone (800) 782-7706 • (626) 968-6681 • Fax (626) 855-4862 • Web: www.whitehallmfg.com
Assemble waste piping using TEFLON tape on all threaded connections and make up waste connections
7 to 1-1/2" P-trap.
FIXTURE ASSEMBLY
NOTE: Waste assembly may require field cutting and fitting
by the installer.
BRASS P-TRAP PLASTIC P-TRAP
7"
(178)
7"
(178)
TYPICAL PLASTIC P-TRAP
INSTALLATION
TYPICAL BRASS P-TRAP
INSTALLATION
11
Instructions for Operation and Care of Best-Care WH3820
®
WHITEHALL MANUFACTURING • P.O. BOX 3527 • City of Industry, CA 91744-0527 U.S.A
Phone (800) 782-7706 • (626) 968-6681 • Fax (626) 855-4862 • Web: www.whitehallmfg.com
Before re-installing access panel(s) it is the installers responsibility to
open stop(s), run faucet(s) and inspect for leaks. If leaks are detected
they must be corrected.
Insert Access Backing Panel Bracket Tabs 14 into Frame Slots 15 and rotate Access Panel 1 into position. Secure
8 Access Panel 1 to Frame Assembly 2 with Vandal Resistant Fasteners 3, using installer provided Center Reject
Allen Wrench 16.
FIXTURE ASSEMBLY
2
3
1
3
14
15
3
1
16
/
