INSTALLATION GUIDE
READ AND SAVE THESE INSTRUCTIONS
Page 22
Low Profile Mount
Mounting
Flat ceilings as low as 8 feet
(2.4meters)
Input Voltage
100–240 VAC, 50–60 Hz
Standard Mount
Mounting
Flat ceilings from 8.5 to 11 feet
(2.5 to 3.4 meters)
Input Voltage
100–240 VAC, 50–60 Hz
Universal Mount
Mounting
Sloped or flat ceilings from 11 to 18feet
(3.4 to 5.5 meters)
Input Voltage
100–240 VAC, 50–60 Hz
Page 15Page 6
Follow the instructions for your mount type. Each mount uses dierent parts and hardware.
HAIKU® BY BIG ASS FANS
1
BEFORE YOU START
Turn O Power
Contact a licensed electrician
if you are uncomfortable
performing electrical work. A
licensed electrician must install
the fan if required by local code.
Do not use the fan with a
dimmer switch.
Turn o power at breaker!
Prepare Fan Site
Outlet Box: Make sure your outlet box is suitable for fan
support. If there is not an outlet box at the fan location,
install one on a ceiling joist or beam.
Concrete Ceiling: Install an anchor hook for the safety
cable if required by your local building and safety code.
See the following page for installation details.
Wood Ceiling Joist: Attach the mounting plate or mounting
bracket directly to the joist using two wood screws (not
supplied). Big Ass Fans recommends using corrosion-
resistant 12-11 x 45 mm hex head timber screws with seal.
Gather Tools
Select Extension Tube (Universal Mount Only)
If your fan uses the universal mount, you will need to select
the appropriate extension tube for your ceiling height and
slope.
See page 4 for a guide to select the most appropriate
extension tube.
Ø 6 mm
112 mm
45 mm 43 mm
40 mm
Ø 8 mm
(anchor bolt)
Ø 14 mm
(anchor hook)
80 mm
100 mm
Ø 12–12.5 mm
45 mm
35 mm 35 mm
REV. D | © 2018 BIG ASS FANS | ALL RIGHTS RESERVED
2
Standard Mount Universal MountLow Profile Mount
Concrete Ceiling
Install an anchor hook for the safety cable if required by your local building and safety code.
50 mm max
40 mm max
35–40 mm
35–40 mm
50 mm max
40 mm max
HAIKU® BY BIG ASS FANS
3
Low Profile Mount
Drill four Ø 8 mm holes in the pattern shown. The hole depth should not exceed 40 mm. Remove any dust
from the holes. Insert four anchor bolts into the holes. Strike the heads of the anchor bolts with a hammer,
ensuring the bolt sleeves are flush with the ceiling surface. Position the mounting plate on the anchor bolts.
Ensure all four anchor bolts are fully tightened to expand and lock the anchors.
If required by local building and safety codes, install an anchor hook for the safety cable. Drill a Ø 14 mm
hole for the anchor hook in the pattern shown. The hole depth should not exceed 50 mm. Remove any dust
from the hole, and then insert the anchor hook and fully tighten.
Standard Mount
Drill three Ø 12–12.5 mm holes in the pattern shown. The hole depth should not exceed 35–40 mm.
Remove any dust from the holes. Insert three anchor bolts into the holes. Strike the heads of the anchor
bolts with a hammer, ensuring the bolt sleeves are flush with the ceiling surface. Position the hanger plate
on the anchor bolts. Ensure all three anchor bolts are fully tightened to expand and lock the anchors.
If required by local building and safety codes, install an anchor hook for the safety cable. Drill a
Ø8–8.5mm hole for the anchor hook adjacent to the hanger plate. The hole depth should not exceed
35–40mm. Remove any dust from the hole, and then insert the anchor hook and fully tighten.
Universal Mount
Drill three Ø 6 mm holes in the pattern shown. The hole depth should not exceed 40 mm. Remove any dust
from the holes. Insert three anchor bolts into the holes. Strike the heads of the anchor bolts with a hammer,
ensuring the bolt sleeves are flush with the ceiling surface. Position the mounting bracket on the anchor
bolts. Ensure all three anchor bolts are fully tightened to expand and lock the anchors.
If required by local building and safety codes, install an anchor hook for the safety cable. Drill a Ø 8 mm
hole for the anchor hook. The hole depth should not exceed 50 mm. Remove any dust from the hole, and
then insert the anchor hook and fully tighten.
REV. D | © 2018 BIG ASS FANS | ALL RIGHTS RESERVED
4
Choosing an Extension Tube (Universal Mount Only)
Consult the tables below to select the appropriate extension tube for your fan.
Ceiling Slope
Haiku fans with a universal mount can be installed on sloped
ceilings with an angle no greater than 33°.
Fan Diameter
Maximum
Ceiling Slope
Extension Tube
Length
52 in.
(1.3 m)
26°
20 in.
(508 mm)
52 in.
(1.3 m)
33°
32 in.
(813 mm)
60 in.
(1.5 m)
22°
20 in.
(508 mm)
60 in.
(1.5 m)
33°
32 in.
(813 mm)
84 in.
(2.1 m)
16°
20 in.
(508 mm)
84 in.
(2.1 m)
29°
32 in.
(813 mm)
Ceiling Height
For optimum performance, Big Ass Fans recommends the
following extension tube lengths based on ceiling height.
Ceiling Height Extension Tube Length
9.5–11 ft
(2.9–3.4 m)
20 in.
(508 mm)
11–13 ft
(3.4–4 m)
32 in.
(813 mm)
13–14 ft *
(4–4.3 m) *
48 in. *
(1219 mm) *
>14 ft *
(>4.3 m) *
60 in. *
(1524 mm) *
* Big Ass Fans recommends using an extended length
extension tube for ceiling heights over 13 ft (4 m). The fan
comes standard with 20 in. (508 mm) and 32 in. (813 mm)
extension tubes. Other lengths are available by contacting
Customer Service.
HAIKU® BY BIG ASS FANS
5
Haiku Remote
Do not expose the remote control to rain or water.
Turns fan on or o.
Sets fan timer length of up to eight hours. Each
press extends timer by one hour.
Turns light on or o. Clears active fan timer.
Increases fan speed/light brightness. Varies fan speed to simulate a natural breeze.
Decreases fan speed/light brightness.
Automatically adjusts your fan speed overnight to
keep you comfortable while you sleep.
Universal Mount
6
REV. D | © 2018 BIG ASS FANS | ALL RIGHTS RESERVED
UNIVERSAL MOUNT
Safety cable not shown
If the EMI filter is included, install it with your fan.
Mounting Bracket
Canopy
Extension Tube
Lower Cover
M5 Screws (6)
Canopy Screws (4)
Wiring Cover
Airfoils (3)
M6 Nut
M6 x 32 mm Bolt
Grommets (6)
Mounting Ball
and Wedge
Motor Hub
Wire Connectors
6 mm Steel Pin
Universal Mount
7
HAIKU® BY BIG ASS FANS
Install Airfoils
Remove and recycle the plastic protective cover.
Moving clockwise, align each airfoil on the fan hub and secure
it with the airfoil hardware (Fig. 1). Make sure the sticker color
on each airfoil matches the corresponding sticker color on
the fan hub!
M5 Screw
Grommet
1
Fig. 1
Airfoil
Lower Cover
Fig. 2
2
Install Lower Cover
If you purchased the fan light kit, proceed to the
instructions included with the kit, and then return to
these instructions.
Attach the lower cover as shown (Fig. 2).
Universal Mount
8
REV. D | © 2018 BIG ASS FANS | ALL RIGHTS RESERVED
3
Attach Extension Tube and Wiring Harness
Align the holes on the extension tube with the holes on the motor bracket, and then secure the tube with the M6 x 32 mm bolt and M6
nut (Fig. 3.1).
Connect the wiring harness from the extension tube to the receptacle from the motor hub (Fig. 3.2).
Fig. 3.1 Fig. 3.2
Wiring
Harness
M6 x 32 mm Bolt
M6 Nut
Universal Mount
9
HAIKU® BY BIG ASS FANS
4
Install Lower Safety Cable and Ground Wire
Install the safety cable and ground wire lugs with the unpainted screws and lock washers (Fig. 4.1).
Make sure all hardware is secure, and then gently tug the cables at the top of the extension tube to reduce slack (Fig.4.2).
Slide the wiring cover down the extension tube, resting it on the fan hub. Make sure no wires are visible between the cover and fan hub.
Slide the canopy down the extension tube (Fig.4.3).
Fig. 4.1 Fig. 4.2 Fig. 4.3
Safety Cable
Ground Wire
(Green)
Lock
Washer
Screw
Wiring
Cover
Canopy
Universal Mount
10
REV. D | © 2018 BIG ASS FANS | ALL RIGHTS RESERVED
5
Install Mounting Ball
Slide the mounting ball over the extension tube (Fig. 5.1).
Insert the 6 mm steel pin into the hole at the top of the extension tube, and then slide the mounting ball upward, seating the steel pin in
the inner slots (Fig. 5.2).
Insert the wedge into the mounting ball and secure it with the screw. Tighten the screw enough to prevent movement between the
mounting ball and extension tube, but do not over-tighten (Fig. 5.3).
Fig. 5.1
Fig. 5.2
Fig. 5.3
Extension
Tube
Mounting
Ball
6 mm Steel Pin
Screw
Wedge
Universal Mount
11
HAIKU® BY BIG ASS FANS
Install Mounting Bracket
Disconnect power to the fan location before installing the
mounting bracket!
Secure the mounting bracket to the mounting structure with
suitable hardware (Fig. 6).
Outlet box shown. Your mounting structure may dier from
the illustration.
6
Fig. 6
Suitable Mounting
Hardware
Mounting
Bracket
7
Hang Fan
Raise the fan to the mounting bracket. Align the rib in the
mounting bracket with the slot in the mounting ball, position
the mounting ball, and let the fan hang freely (Fig. 7).
Gently twist the extension tube to ensure it is properly seated
and will not move during fan operation.
Fig. 7
Mounting
Bracket
Mounting
Ball
Universal Mount
12
REV. D | © 2018 BIG ASS FANS | ALL RIGHTS RESERVED
Wire the Fan
Disconnect power to the fan location before wiring the fan!
Do not connect the fan to a damaged power source! Do not attempt to resolve electrical failures on your own. Consult a
qualified electrician if uncertain of the electrical installation of this fan.
Wire the fan as shown in the diagram using the wire connectors (Fig. 8). If your fan packaging included an EMI filter, install it as shown.
Attach the green ground wire to the mount with the unpainted screw. Connect the wiring harness from the power supply to the wiring
harness from the extension tube, making sure that the wiring and safety cable are routed in the same direction.
8
North America
100–120 V
All other regions
AC Hot/L1
Brown
Black Brown
AC Neutral/L2
Blue
White Blue
PE/Earth Ground
Green with Yellow
Green or Bare
Copper
Green with Yellow
Fig. 8
Universal Mount
13
HAIKU® BY BIG ASS FANS
Wiring Diagram
(No EMI Filter)
WHITE
BLACK
BROWN
BLUE
WHITE
BLACK
BROWN
BLUE
EMI FILTER
Wiring Diagram
(With EMI Filter)
GREEN &
YELLOW
GREEN &
YELLOW
Universal Mount
14
REV. D | © 2018 BIG ASS FANS | ALL RIGHTS RESERVED
9
Secure Safety Cable
Loop the safety cable around the mounting bracket or building
structure, and then secure it with the shackle (Fig. 9).
Canada: The safety cable must be secured directly
to an existing part of the building structure. It
may be necessary to install additional structural
material to provide attachment points.
Safety Cable
Shackle
Fig. 9
10
Raise Canopy
Raise the canopy to the mounting bracket, aligning the four
holes on the canopy with the holes on the bracket. Secure
the canopy to the mounting bracket with the painted screws
(Fig.10). Make sure all wires and the safety cable are tucked in
the canopy.
Canopy
Canopy Screw
Fig. 10
Congratulations!
Installation is now complete. Test your fan using the remote
control.
Low Profile Mount
HAIKU® BY BIG ASS FANS
15
LOW PROFILE MOUNT
Use the extension tube screw caps that match the color of your fan.
Safety cable not shown.
Mounting Plate
Rubber Bumpers (2)
Mounting Brackets (2)
6 mm Nylock Nuts (4)
Extension Tube Screw Caps (2)
Lower Cover
Grommets (6)
M5 Screws (6)
Motor Hub
Wiring Cover Screws (2)
Airfoils (3)
Wire Connectors
Wiring Cover
Wiring Cover Trim
Low Profile Mount
REV. D | © 2018 BIG ASS FANS | ALL RIGHTS RESERVED
16
Install Mounting Plate and Single Bracket
Slide the rubber bumpers onto the extension tube brackets (Fig. 1.1).
Secure the mounting bracket to the mounting structure with suitable hardware (Fig. 1.2). Your mounting structure may dier from the
illustration.
Loosely attach one mounting bracket to the mounting plate with two 6 mm nylock nuts, but do not fully tighten (Fig. 1.3).
Fig. 1.1 Fig. 1.2
1
Fig. 1.3
Rubber
Bumper
Extension Tube Brackets
Mounting
Plate
6 mm Nylock Nut
Mounting Plate
Suitable Mounting
Hardware
Outlet box shown. Your mounting
structure may dier from the illustration.
Low Profile Mount
HAIKU® BY BIG ASS FANS
17
Mounting
Plate
Safety
Cable
Shackle
Fig. 2.2
Secure Safety Cable
Raise the fan to the bracket and temporarily rest one rubber bumper in the space between the bracket and plate (Fig. 2.1). While
supporting the fan, loop the safety cable around the mounting plate or building structure, and then secure it with the shackle (Fig.2.2).
2
Fig. 2.1
Canada: The safety cable must be secured directly to an existing part of the building structure. It may be necessary to
install additional structural material to provide attachment points.
Low Profile Mount
REV. D | © 2018 BIG ASS FANS | ALL RIGHTS RESERVED
18
Wire Fan
Disconnect power to the fan location before wiring the fan!
Do not connect the fan to a damaged power source! Do not
attempt to resolve electrical failures on your own. Consult a
qualified electrician if uncertain of the electrical installation
of this fan.
Allow the fan to hang from the safety cable. Wire the fan as shown
in the diagram using the wire connectors (Fig. 3).
Fig. 3
3
Wiring Diagram
BLUE
BROWN
WHITE
BLACK
GREEN &
YELLOW
North America
100–120 V
All other regions
AC Hot/L1
Brown
Black Brown
AC Neutral/L2
Blue
White Blue
PE/Earth Ground
Green with Yellow
Green or Bare
Copper
Green with Yellow
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI