Tektronix WVR7020 Technical Reference

x

WVR6020, WVR7020, WVR7120, WVR6100 Opt. MB,

WVR7000 Opt. MB, and WVR7100 Opt. MB

Waveform Rasterizers

ZZZ

Technical Reference

*P077008201*

077-0082-01

WVR6020, WVR7020, WVR7120, WVR6100 Opt. MB,

WVR7000 Opt. MB, and WVR7100 Opt. MB

Waveform Rasterizers

ZZZ

Technical Reference

xx

www.tektronix.com

077-0082-01

protected by na

tional copyright laws and international treaty provisions.

Tektronix pro

ducts are covered by U.S. and foreign patents, issued and pending. Information in this publication s upersedes that in all

previously published material. Speciﬁcations and price change privileges reserved.

TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

Contacting Tektronix

Tektronix, Inc.

14200 SW Karl Braun Drive

P.O. Box 500

Beaverton, OR 97077

USA

For product information, sales, service, and technical support:

In North America, call 1-800-833-9200.

Worldwide, visit www.tektronix.com to ﬁnd contacts in your area.

Warranty

Tektronix warrants that this product will be free from defects in materials and workmanship for a period of one (1) year from the date of

shipment. If any such product proves defective during this warranty period, Tektronix, at its option, either will repair the defective

product without charge for parts and labor, or will provide a replacement in exchange for the defective product. Parts, m odules and

replacement products used by Tektronix for warranty work may be new or reconditioned to like new performance. All replaced

parts, modules and products become the property of Tektronix.

In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the warranty period

and make suitable arrangements for the performance of service. C ustomer shall be responsible for packaging and shipping the

defective product to the service center designated by Tektronix, with shipping charges prepaid. Tektronix shall pay for the return of the

product to Customer if the shipment is to a location within the country in which the Tektronix service center is located. Customer shall

be responsible for paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.

This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance and

care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting from attempts by personnel

other than Tektronix representatives to inst all, repair or service the product; b) to repair damage resulting from improper use or

connection to incompatible equipment; c) to repair any damage or malfunction caused by the use of non-Tektronix supplies; or

d) to service a product that has been modiﬁ ed or integrated with other products when the effect of such modiﬁcation or integration

increases the time or difﬁculty o f servicing the product.

THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO TH E PRODUCT IN LIEU OF ANY OTHER WARRANTIES,

EXPRESS OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’ RESPON SIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS

IS THE SOLE AN D EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BR EAC H OF TH IS WARRANTY. TEKTRONIX

AND ITS VENDORS WILL NOT BE LIABLE FO R ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIA L DAMAGES

IRRESPECTIVE O F WHE THER TEKTRONIX OR THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH

DAMAGES.

[W2 – 15AUG04]

Table of Content

s

Table of Contents

General Safety Summary .............................. ... . .. . . . . .. . .................... ... . .. . . . . .. . .................... ... . .. . . . . . .. iii

Preface................................................................................................................................. v

Where to Find More Information................................................................................................. v

Conventions Used in this Manual . . ... .............. ... . . . . ... .............. ... . . . . ................. . .. . . . . ................. . .. . v

Incoming In

spection ................................................................................................................... 1

Installation Variations.................................................................................................................. 5

Connecting Directly to a PC ............................ ... ...... ... ... ... ...... ... ... ...... ... ... ...... ... ... ...... ... ... ...... . 5

Connectin

g to a Network......................................................................................................... 6

Remote Communication ......................................................................................................... 8

Display Information ................................................................................................................... 17

Waveform D

isplay............................................................................................................... 17

Vector Display...................................................................................................................19

Timing Display...................................................................................................................20

Picture D

isplay .................................................................................................................. 22

Audio Display....................................................................................................................25

LTC Waveform Display.......................................................................................................... 28

Gamut Di

splay................................................................................................................... 29

Status Display...................................................................................................................30

Eye Display......................................................................................................................33

Jitter

Display..................................................................................................................... 35

Ancillary (ANC) Data Inspector................................................................................................. 37

Supplemental Operating Information ...... . . . . .................... . . . . ... ................. . . . . ... ................. . . . . ... ...........43

Clonin

g Setups (Presets) ....................................................................................................... 43

Upgrading Instrument Software ................................................................................................ 49

Description of Cable Types ..................................................................................................... 55

Index

Waveform Rasterizers Technical Reference i

Table of Content

s

ii Waveform Rasterizers Technical Reference

General Safety S

ummary

General Safet

y Summary

Review the following safety precautions to avoid injury and prevent damage to this product or any products connected to it.

To avoid potential hazards, use this product only as speciﬁed.

Only qualiﬁed personnel should perform service procedures.

To Avoid Fire or Personal Injury

Use Proper Power Cord. Use only the power cord speciﬁed for this product and certiﬁed for the country of use.

Connect and Disconnect Properly. Connect the probe output to the m easurement instrument before connecting the

probe to the circuit under test. Connect the probe reference lead to the c ircuit under test before c onnecting the probe

input. Dis

connect the probe input and the probe reference lead from the circuit under test before disconnecting the probe

from the measurement instrument.

Ground the Product. This product i s grounded through the grounding conductor of the power cord. To avoid electric

shock, the grounding conductor must be connected to earth ground. Before making connections to the input or output

terminal

s of the product, ensure that the product is properly grounded.

Observe A

ll Terminal Ratings.

To avoid ﬁre or shock hazard, observe all ratings and markings on the product. Consult

the product manual for further ratings information before making connections to the product.

Do not apply a potential to any terminal, including the common terminal, that exceeds the maximum rating of that terminal.

Power Disconnect. The power cord disconnects the product from the power source. Do not block the power cord; it

must remain accessible to the user at all times.

Do Not Operate Without Covers. Do not operate this product w ith covers or panels removed.

Do Not Operate With Suspected Failures. If you suspect that there is damage to this product, have it inspected by

qualiﬁ

ed service personnel.

Avoid E

xposed Circuitry.

Do not touch exposed connections and components when power is present.

Use Pr

oper Fuse.

Use only the fuse type and rating speciﬁed for this product.

Do Not Operate in Wet/Damp Conditions.

Do Not Operate in an Explosive Atmosphere.

Keep Product Surfaces C lean and Dry.

Pro

vide Proper Ventilation.

Refer to the manual’s installation instructions for details on installing the product so it has

proper ventilation.

Waveform Rasterizers Technical Reference iii

General Safety S

ummary

TermsinthisManual

These terms may appear in this manual:

WARNING. Warning s tatements identify conditions or practices that could r esult in injury or loss of life.

CAUTION. Caution statements identify c onditions or practices that could result in damage to this product or other property.

Symbols and Terms on the Product

These terms may appear on the product:

DANGER indicates an injury hazard immediately accessible as you read the marking.

WARNING indicates an injury hazard not immediately accessible as you read the marking.

CAUTION indicates a hazard to property including the product.

The following symbol(s) may appear on the product:

iv Waveform Rasterizers Technical Reference

Preface

This manual contains supplemental user information for the following instruments:

WVR6020

WVR7020

WVR7120

WVR6100 with O ption MB

WVR7000 with O ption MB

WVR7100 with O ption MB

Where to Find More Information

Item Purpose Location

Quick Start User Manual

Installation and high-level

overview of instrument

operation

Online Help

In-depth instrument

operation and UI help

Speciﬁcations and

Performance Veriﬁcation

Speciﬁcations and

procedure for checking

instrument performance

WFM, WVR, and AMM

Series Management

Information Base (MIB)

SNMP command

reference for remotely

controlling the instrument

Service M anual Optional manual

supporting module-level

servicing of the

instrument

Conventions Used in this Manual

The following icons are used throughout this manual:

Sequence Step Connect power

Network

XGA

Waveform Rasterizers Technical Reference v

Preface

vi Waveform Rasterizers Technical Reference

Incoming Inspec

tion

Incoming Inspection

The incoming inspection procedures are optional procedures that check the functionality of the instrument and require

no equipment other than a display. For a more robust inspection, see the performance veriﬁcation procedures in the

Speciﬁcations and Performance Veriﬁcation manual that is included on the User Documentation CD that was shipped

with your instrument.

BasicTurnOnandSelfTest

1. Connect an XGA monitor to the

instrument.

2. Connect the AC power cord to the rear of

the instrument and to a 100 to 240 VAC

source. There is no power switch on

your instrument: it will turn on as soon

as you apply power.

3. Look at the front panel immediately after

you apply power. All of the buttons, the

text over the three knobs, and the Fault

indicator should light up.

NOTE. After a couple of seconds, the lights

in the buttons and text will turn off. After

about 15 seconds, the fault light should turn

off and the Power On diagnostic page should

appear on the monitor.

4. Verify that the instrument passes all self

tests. Any failures will be shown in Red.

The results of the Power On diagnostics

are erased from the screen, but you

can view them by selecting CONFIG >

Utilities > View Diagnostic Log.

5. After the diagnostics are ﬁnished, the

instrument state will be restored. When

the progress indicator in the lower-right

part of the screen is ﬁnished, the

instrument has ﬁnished initi alizing.

Waveform Rasterizers Technical Reference 1

Incoming Inspec

tion

Front Panel Test

1. Press FACTORY

to restore the factory

preset. Wait for the progress indicator to

show the process is complete.

2. Press FULL to m a ke the ac tive tile be

full screen.

3. Press HELP to

display the help screen.

4. Press all the

other buttons.

Each button s hould ﬂash as you press

it. Most buttons bring up related help

text. Some b

uttons, such as the presets,

bring up the same information. The

HELP button, the four arrow keys, and

the SEL but

ton do not bring up help text

because they traverse the help panes

and content.

5. Press the right arrow key until the Help

Contents pane in the upper-left corner is

highligh

ted.

6. Turn the G

ENERAL knob and verify that

the selector box moves up and down the

list.

7. Press HELP to exit help.

2 Waveform Rasterizers Technical Reference

Incoming Inspec

tion

XGA and Extended Diagnostics Test

NOTE. Where th

e following procedure says to press an arrow key, you can use the general knob on the front panel,

if you prefer.

1. Press the CONFIG button to display the

conﬁguration menu.

2. Select Utilities and then press SEL.

3. Select CPU Color Palette Check

and verify

that 16 distinct colors are

displayed. This tests the XGA data path

from the CPU.

4. Use the down arrow key to navigate to

Run Advanced Diagnostics and then

press SEL.

5. When the dialog box appears, use the

right arrow key to highlight the Continue

box and then press SEL to run the test.

6. Verify that the XGA DAC is working by

looking at the White and Red ramps at

the top of the screen, and at the Green

and Blue ramps a t the bottom of the

screen. They should not have steps but

should show a smooth transition from

dark to light.

Waveform Rasterizers Technical Reference 3

Incoming Inspec

tion

7. Verify that the frequencies shown are

within 10 kHz, and that rates shown are

within 0.1 μs,

of the nominal values listed

to the right.

8. Verify that the bus bit activity tests

(labeled Channel A:, Processor Video:,

and Composi

te Video:, and appearing at

the bottom of the screen) are as follows:

All three tests show both a red and a

green bar in each bit location.

The Processors Video test shows

8bitsfrom

the CP U, a space, then

Hsync, a space, Vsync, a space, and

then the blank line. It is normal for

the Vsync b

it to blink o ccasionally.

9. Press SEL

or cycle the power to reboot

the unit for normal operation.

QDR Clock = 25.174 MHz

VGA clock = 64.480 MHz

Audio PLL1 =

12.288 MHz

Audio PLL2 = 12.288 MHz

Hsync rate : Width = 0.9 μs

Vsync P W: Wi

dth = 62.5 μs

Fan Test

If the fault light in the lower left corner of the front panel is not on (Red), the fans are running. You should also be able to hear

them and feel air coming out the back of the instrument. At low temperatures, the fans will turn slowly and be very quiet.

4 Waveform Rasterizers Technical Reference

Installation Va

riations

Installation Variations

See the Quick Start User Manual that was shipped with your instrument for basic installation instructions. Read the following

information for other installation situations and for remote communication instructions, an optional procedure that is suitable

for incoming inspection of this product.

Connecting Directly to a P C

The following procedure will help you connect y our instrument to a PC:

1. Connect the instrument to a PC through

an ethernet

hub, as shown. A standard

crossover cable can be substituted for

the hub.

2. Set up the instrument as described in

the follow

ing procedures (See page 6,

Connecting to a Network.), choosing

Manual IP mode to set the IP address

manually

. B e sure to set an address that

is compatible with the setting of your PC.

3. If you are using an SNMP setup, use the

SNMP setup procedure.

Waveform Rasterizers Technical Reference 5

Installation Va

riations

Connecting to a Network

The following topics cover conﬁguring the IP settings, so that you can use your instrument over a network, and conﬁguring

SNMP, which is required if you are using commands to control the instrument.

Connection and IP Settings

To allow net

work access to the instrument, y ou need to set the IP address. Network addresses can be assigned either

automatically or manually. If your network does not use DHCP, you will have to m anually enter the address for the instrument.

To get an address, talk to your LAN administrator.

To connect your instrument to a network and

access it wi

th a remote PC, do the following:

NOTE. To connect directly between your PC

and the instrument, see Connecting Directly

to a PC.

1. Press CONFIG to display the

Conﬁguration menu.

2. Select Network Settings > Web Enable.

Press SEL to select On.

6 Waveform Rasterizers Technical Reference

Installation Va

riations

3. Set the IP Conﬁg Mode to Manual or

DHCP, depending on your network setup.

4. If you cannot use DHCP, set the subnet

mask and gatew

ay address network

parameters in this menu; see your

LAN administrator for required values.

(Besuretous

e compatible addresses

between the PC and the instrument.)

You can also set the instrument name

and view the

MAC Address.

5. If the passw

ord is set, note it. You will

be prompted for it when you connect to

the instrument.

NOTE. For h

elp w ith entering or changing

the password, select Web Password, and

press the HELP button.

6. Press CONFIG to close the Conﬁguration

menu.

Waveform Rasterizers Technical Reference 7

Installation Va

riations

SNMP Setup

If you intend to use SNMP commands to control the instrum ent (SNMP control is primarily intended for access through

automation systems), you need to set up SNMP parameters.

NOTE. The WFM, WVR, and AMM Series Waveform Monitors wfm_mon.mib and the WVR7120.mib can be downloaded

from the instrument Web page.

The procedure to set SNMP settings is similar to that shown on page 2 for IP settings; the parameters that can be set follow:

SNMP Enable This entry in the Network Settings portion of the Conﬁguration m enu allows you to

turn on or off the remote access through SNMP.

SNMP Trap Enable This menu entry allows you to turn on or off the traps that are sent out through SNMP.

SNMP Trap Address This menu entry allows you to set IP addresses to w hich SNMP traps are sent through

SNMP. Traps can be sent to up to four addresses when error conditions are detected.

NOTE. A value of all zeroes for the address will disable that trap output.

Private Community S tring This menu entry allows yo u to set the Private Community string. This string is

effectively a password. Without this string, SNMP commands cannot change values

in the instrument.

NOTE. The P rivate S tring is necessary for SNMP access to write changes into

the instrument.

Public Community String This menu entry allows you to set the Public Community string. This string is

effectively a password. Without this string, SNMP commands cannot read values

from the instrument.

NOTE. The Public String is necessary for SNMP access to read values from the

instrument.

Remote Communication

The f

ollowing topics cover remote c ommunications that occur:

Over

an Ethernet network through a Web browser

Ove

r an Ethernet network through a Java applet

Ove

r a cable using the optional remote front panel

8 Waveform Rasterizers Technical Reference

Page is loading ...

Tektronix WVR7020 Technical Reference

This manual is also suitable for

Tektronix WVR7020 Technical Reference

Related papers

Other documents