CASINO SOFTWARE EMP 8×0 v5 Electronic Coin Selector Operating instructions

Brand
CASINO SOFTWARE
Model
EMP 8×0 v5 Electronic Coin Selector
Type
Operating instructions

CASINO SOFTWARE EMP 8×0 v5 Electronic Coin Selector

The EMP 8×0 v5 is an electronic coin selector designed for use in a variety of applications, including casinos, arcades, and vending machines. It is a robust and reliable device that can operate in harsh environments. The EMP 8×0 v5 can be easily cleaned and maintained, and it offers a variety of features that make it a valuable asset to any business.

Some of the key features of the EMP 8×0 v5 include:

  • The ability to accept a wide variety of coins, including foreign coins
  • High-speed coin acceptance
  • Adjustable coin acceptance parameters

CASINO SOFTWARE EMP 8×0 v5 Electronic Coin Selector

The EMP 8×0 v5 is an electronic coin selector designed for use in a variety of applications, including casinos, arcades, and vending machines. It is a robust and reliable device that can operate in harsh environments. The EMP 8×0 v5 can be easily cleaned and maintained, and it offers a variety of features that make it a valuable asset to any business.

Some of the key features of the EMP 8×0 v5 include:

  • The ability to accept a wide variety of coins, including foreign coins
  • High-speed coin acceptance
  • Adjustable coin acceptance parameters
wh Münzprüfer Berlin GmbH, Germany Maintenance Instructions EMP 8x0 v5, v6 v7
wh Münzprüfer Berlin GmbH Teltower Damm 276 D - 14167 Berlin
- version 2.00 -
Maintenance Instructions
Electronic Coin Selector
EMP 8x0 v5
EMP 8x0 v6
EMP 8x0 v7
Maintenance Instructions EMP 8x0 v5, v6, v7 wh Münzprüfer Berlin GmbH, Germany
version 2.00
page 2/7 subject to technical modification EMP8x0 v5, v6, v7
Table of Content
1.
Introduction .........................................................................................4
1.1.
Cleaning .......................................................................................... 4
1.2.
Advanced Cleaning............................................................................ 6
wh Münzprüfer Berlin GmbH, Germany Maintenance Instructions EMP 8x0 v5, v6,v7
version 2.00
EMP8x0 v5, v6, v7 subject to technical modification page 3/7
Safety Precautions
You are advised to observe the safety information during operation, maintenance and
repairing of electronic coin selectors of the EMP 800 series. Failure to do so may result in
warranty and other claims being excluded.
Whilst every care has been taken in the preparation of information contained in this
manual, wh Münzprüfer Berlin GmbH will not be liable for any consequential loss or damage
howsoever caused.
This manual is protected by copyright and all rights are reserved. Without prior
authorisation by wh Münzprüfer Berlin GmbH, no part of this manual may be reproduced
in any form by photocopy, microfilm or other processes nor may it be transmitted in any
form usable by data processing. The rights of reproduction by lecture are also reserved.
The Company would be very grateful if any accidental inaccuracies could be pointed out to
us with any other constructive criticism which might lead to a better understanding.
Maintenance Instructions EMP 800 v5, v6, v7 wh Münzprüfer Berlin GmbH, Germany
version 2.00
page 4/7 subject to technical modification EMP8x0 v5, v6, v7
1. Introduction
The EMP 800 is an extraordinarily robust coin selector and operates relatively
maintenance free. However, it should be cleaned at regular intervals especially
if it is operating in an environment with high levels of dust, smoke or nicotine.
The cleaning intervals are of course dependent on the level of air borne
contaminants.
1.1. Cleaning
Modest use with minimum contaminant levels indicate the need to clean the top
of the coin path once a year. Open the coin path door and wipe the exposed
surfaces with an alcohol moistened cloth. Also lukewarm water with a little
washing-up liquid may be used. It is important that no dirt is pushed inside the
openings of the optical sensors. The light sensors may be cleaned with a soft
brush or air duster spray.
Make sure that the coin selector is without power during the
cleaning.
Use a damp not wet - cloth. Under no circumstances liquid
should run into the coin selector.
Avoid solvent or abrasives which may affect the plastic
material.
Never use an oily rag! Never lubricate the solenoid, hinge
joints etc.!
Fig. 1: Cleaning the coin flap and rail of EMP 800v7 with a soft cloth
wh Münzprüfer Berlin GmbH, Germany Maintenance Instructions EMP 8x0 v5, v6,v7
version 2.00
EMP8x0 v5, v6, v7 subject to technical modification page 5/7
Fig. 2: Cleaning the coin path of EMP 800v7 with a brush
Fig. 3: Cleaning the coin flap and rail of EMP 800v6 with a soft tool
Fig. 4: Cleaning the coin path of EMP 800v6 with a brush
Maintenance Instructions EMP 800 v5, v6, v7 wh Münzprüfer Berlin GmbH, Germany
version 2.00
page 6/7 subject to technical modification EMP8x0 v5, v6, v7
Fig. 5 Cleaning the light sensors with an air spray duster.
1.2. Advanced Cleaning
In cases of a specially rough environment (e.g. car wash with coin extraction
system or vacuum cleaners) it might be necessary to carry out some additional
cleaning. Therefore the prism below the solenoid should be removed and carefully
cleaned with a soft cloth.
Fig. 6 Removing the solenoid from the selector EMP 800 v7 and 800 v6.
Fig. 7 Removing the solenoid from the selector EMP 800 v7 and 800 v6.
wh Münzprüfer Berlin GmbH, Germany Maintenance Instructions EMP 8x0 v5, v6,v7
version 2.00
EMP8x0 v5, v6, v7 subject to technical modification page 7/7
Make sure that the thin connecting cables are not damaged.
Fig. 8 Location of the prism EMP 800 v7 and 800 v6.
Fig. 9 Removing the prism from the selector EMP 800 v7 and 800 v6.
Once the prism has been cleaned assemble the components in reverse order. Pay
attention to the orientation of the prism. The bevel edges must be visible on the
upside.
Fig. 10 Dirty and cleaned prism.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

CASINO SOFTWARE EMP 8×0 v5 Electronic Coin Selector Operating instructions

Brand
CASINO SOFTWARE
Model
EMP 8×0 v5 Electronic Coin Selector
Type
Operating instructions

CASINO SOFTWARE EMP 8×0 v5 Electronic Coin Selector

The EMP 8×0 v5 is an electronic coin selector designed for use in a variety of applications, including casinos, arcades, and vending machines. It is a robust and reliable device that can operate in harsh environments. The EMP 8×0 v5 can be easily cleaned and maintained, and it offers a variety of features that make it a valuable asset to any business.

Some of the key features of the EMP 8×0 v5 include:

  • The ability to accept a wide variety of coins, including foreign coins
  • High-speed coin acceptance
  • Adjustable coin acceptance parameters
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents