Taco 0034ePlus-F2 High-Efficiency Circulator Pump User manual

Brand: Taco

Model: 0034ePlus-F2 High-Efficiency Circulator Pump

Type: User manual

Taco 0034ePlus-F2 High-Efficiency Circulator Pump is a high-performance circulator pump with an advanced digital LED display controller for easy programming and diagnostic feedback. With 5 operating modes and simple keypad programming, its variable speed performance curves are equivalent to the Taco 009, 0010, 0011, 0012, 0012 3-Speed, 0013, 0013 3-Speed & 0014.

The pump's features include:

Simple keypad programming
Digital LED screen display (Watts, GPM, Head, RPM and diagnostic error codes)
Five operating modes to match any system requirements - activeADAPT®, Constant Pressure, Proportional Pressure, Variable Fixed Speed, or 0-10V DC input

The pump's features include:

Simple keypad programming
Digital LED screen display (Watts, GPM, Head, RPM and diagnostic error codes)
Five operating modes to match any system requirements - activeADAPT®, Constant Pressure, Proportional Pressure, Variable Fixed Speed, or 0-10V DC input

DESCRIPTION:

The 0034ePlus is a high performance, variable speed, high-eciency, wet-rotor

circulator with an ECM, permanent magnet motor and an advanced digital LED

display controller for easy programming and diagnostic feedback. With 5 operating

modes and simple keypad programming, its variable speed performance curves are

equivalent to the Taco 009, 0010, 0011, 0012, 0012 3-Speed, 0013, 0013 3-Speed &

0014. Ideal for large residential and light commercial hydronic heating, chilled water

cooling and domestic hot water systems. The 0034ePlus reduces power consumption

by up to 85% compared to equivalent AC permanent split capacitor circulators.

APPLICATION:

• Maximum operating pressure: 150 psi (10.3 bar)

• Minimum NPSHR: 18 psi at 203˚F (95˚C)

• Maximum uid temperature: 230°F (110˚C)

• Minimum uid temperature: 14°F (-10˚C)

• Electrical specications:

Voltage: 115/208/230V, 50/60 Hz, single phase

Maximum operating power: 170W

Maximum amp rating: 1.48 (115V) / .70 (230V)

• Equipped with a cast iron or stainless steel casing

• SS Model suitable for open loop potable water systems

• Taco circulator pumps are for indoor use only – employer uniquement a l’interieur

• Acceptable for use with water or maximum of 50% water/glycol solution

FEATURES:

• Simple keypad programming

• Digital LED screen display (Watts, GPM, Head, RPM and diagnostic error codes)

• Five operating modes to match any system requirements - activeADAPT®,

Constant Pressure, Proportional Pressure, Variable Fixed Speed or 0-10V DC input

• Replaces all single speed and 3-speed circulators in its class

• ECM performance equivalent to Taco’s 009, 0010, 0011, 0012, 0013 & 0014 circulators

• Multi-color LED display showing power on, mode setting and error code diagnostics

• Use with a Taco ZVC Zone Valve Control or SR Switching Relay for ON/OFF operation

• Nut-capture feature on anges for easier t up

• Dual electrical knockouts and removable quick-connect terminal strip for easy wiring

• Whisper quiet operation

• BIO Barrier® protects the pump from system contaminants

• SureStart® automatic unblocking and air purging mode

• Rotatable control cover to allow any pump body orientation

INSTALLATION:

WARNING: Do not use in swimming pool or spa areas. Pump has not been investigated for these applications.

AVERTISSEMENT : Ne pas utiliser dans une piscine ou un spa. La pompe n’a pas été étudiée pour ces applications.

CAUTION: The addition of petroleum based uids or certain chemical additives to systems using TACO equipment

voids the warranty. Consult factory for uid compatibility.

ATTENTION : L’ajout de liquides à base de pétrole ou de certains additifs chimiques à des systèmes utilisant un

équipement TACO annule la garantie. Consultez le fabricant pour connaître la compatibilité de liquides.

CAUTION: Installations at elevations over 5000 feet must have higher ll pressure of 20 psi minimum to prevent

pump cavitation and ashing. Premature failure may result. Adjust expansion tank pressure to equal ll pressure.

A larger size expansion tank may be required.

ATTENTION : Des installations à des altitudes de plus de 1600 mètres doivent présenter une pression de remplissage

plus élevée de 20 psi

au minimum an d’éviter toute cavitation ou ashing de la pompe. Une défaillance prématurée peut en résulter. Réglez la pression

du réservoir d’expansion de façon qu’elle soit égale à la pression de remplissage. Un réservoir d’expansion d’une taille supérieure

peut être nécessaire.

Instruction Sheet

ECM High-Eciency Circulator with Digital Display Controller

102-544

SUPERSEDES: August 16, 2021 EFFECTIVE: December 21, 2021

Plant ID No. 001-5021

-1-

Certified to

NSF/ANSI 61 & 372

Figure 1

Cast Iron model: 0034ePlus-F2

Stainless Steel model: 0034ePlus-SF2

-2-

Figure 2:

KEY:

VI, V2, V3 = SHUT-OFF ISOLATION VALVE

P = TACO 0034ePLUS CIRCULATOR

FF = FAST FILL BOILER FEED VALVE

PV4 = PURGE VALVE

FC = FLOW CHECK VALVE

MOD CON

BOILER

ZONE 1 ZONE 2 ZONE 3

FC FC FC

ZONE 1 ZONE 2 ZONE 3

FCFC - Optional Location FC FC

ZONE 1 ZONE 2 ZONE 3

FCFC - Optional Location FC FC

Figure 2

PREFERRED PIPING FOR CIRCULATORS ON BOILER SUPPLY

PREFERRED PIPING FOR CIRCULATORS ON BOILER RETURN

PREFERRED PRIMARY / SECONDARY PIPING FOR CIRCULATORS ON BOILER SUPPLY

-3-

PREFERRED PIPING FOR ZONE VALVES ON BOILER SUPPLY

KEY:

VI, V2, V3 = SHUT-OFF ISOLATION VALVE

P = TACO 0034ePLUS CIRCULATOR

FF = FAST FILL BOILER FEED VALVE

PV4 = PURGE VALVE

ZV = ZONE VALVE

PREFERRED PRIMARY / SECONDARY PIPING FOR ZONE VALVES ON BOILER SUPPLY

ALTERNATE PIPING FOR ZONE VALVES ON BOILER RETURN

igure 3:

MOD CON

BOILER

ZONE 1 ZONE 2 ZONE 3

ZONE 1 ZONE 2 ZONE 3 ZONE 1 ZONE 2 ZONE 3

Figure 3

PREFERRED PIPING FOR ZONE VALVES ON BOILER SUPPLY

ALTERNATE PIPING FOR ZONE VALVES ON BOILER RETURN

PREFERRED PRIMARY / SECONDARY PIPING FOR ZONE VALVES ON BOILER SUPPLY

1. Location: The circulator can be installed on the supply or return side of the boiler but for best system

performance, it should always pump away from the expansion tank. See piping diagrams in Figure 2 & Figure 3.

NOTE: Two shorter 1-1/4” x 7/16” ange bolts are provided with the circulator to

use on the discharge ange to prevent interference with the circulator casing.

CAUTION: Do not use at rubber gaskets. Only use O-ring gaskets provided or leaks may result. Warranty will be void.

2. Mounting position: Circulator must be mounted with the motor in the horizontal position. See Figure 4 & Figure 5

below for acceptable and unacceptable motor mounting orientations. See Figure 6 for Rotating Control Cover.

CAUTION: To reduce the possibility of noise transmission, be sure to add vibration dampeners to piping when mounting

circulator to wall or oor joists.

ATTENTION : Pour réduire la possibilité de transmission de bruit, veillez à ajouter des amortisseurs de vibration à

la tuyauterie lors du montage du circulateur sur des chevêtres de mur ou de plancher.

3. Filling the system: Fill the system with tap water or a maximum of 50% propylene-glycol and water solution.

The system must be lled before operating the circulator. The bearings are water lubricated and should not

be allowed to operate dry. Filling the system will result in immediate lubrication of the bearings. It is always

good practice to ush a new system of foreign matter before starting the circulator.

WARNING: Risk of electric shock. To reduce the risk of electric shock, be certain that it is connected only to a properly

grounded, grounding-type receptacle. Follow all local electrical and plumbing codes.

AVERTISSEMENT : Risque de choc électrique. Pour réduire le risque de choc électrique, veillez à ce qu’elle soit raccordée uniquement

à un réceptacle de type mise à la terre proprement mis à la terre. Respectez tous les codes de plomberie et électriques locaux.

WARNING: Use supply wires suitable for 90°C.

AVERTISSEMENT : Employer des ls d’alimentation adeqauts pour 90°C.

WARNING: Disconnect power when servicing.

AVERTISSEMENT : Couper l’alimentation lors de l’entretien.

CAUTION: Use exible conduit only. Not for use with rigid conduit.

ATTENTION : N’utiliser que du conduit exible ; n’est pas fait pour du conduit rigide.

Figure 4 — Acceptable Mounting Positions

-4-

Flow

Figure 6 — Rotating Control Cover

Figure 5 — Unacceptable Mounting Positions

The 0034ePlus is equipped

with a symmetrical control

cover connected to the

pump with a ribbon cable.

The cover can be removed,

rotated and repositioned

for best viewing and user

operation. It allows the

installer to mount the

circulator casing in any ow

direction, then rotate the

cover to the upright position.

Remove the 4 cover screws,

rotate cover to upright

position, reattach cover

with 4 screws.

-5-

NEUTRAL

LINE

Removable Green

Terminal Plug

Terminal

Screws

GROUND

GNL

Wiring the circulator: Disconnect AC power supply. Remove terminal box cover. Attach a wiring connector into

knockout hole. Use exible conduit only. The green terminal plug may be removed to simplify wiring, then snapped

back in place. Connect Line/Hot power to the L terminal, Neutral to the N terminal and Ground to the G terminal.

See wiring diagram above. Replace terminal box cover. Insert rubber cap plug provided to cover unused knockout hole.

4a. Wiring the circulator for 0-10V DC Operation: (See Page 10)

5. Start the circulator: When purging the system, it is recommended to run the circulator at full speed long

enough to remove all remaining air from the bearing chamber. This is especially important when installing

the circulator in the o-season. Set operating mode to Fixed Speed on 100% HIGH setting for maximum

xed speed. A blue LED will illuminate when the 0034ePlus is powered on.

CAUTION: Never run the circulator dry or permanent damage may result.

ATTENTION: Ne laissez jamais le circulateur tourner à sec, des dommages permanents peuvent en résulter.

Full Speed Operation:

To run the pump at full speed during the fast ll, start-up and purge process, set operating mode to Fixed Speed on

100% HIGH setting. (See “Programming your 0034ePlus Circulator”). The LED will change to blue. To return to the

normal operating mode, reset operating mode to desired activeADAPT, Constant Pressure, Proportional Pressure,

Fixed Speed or 0-10V setting.

Wiring Diagram

-6-

6. Programming your 0034ePlus circulator: Modify the performance of the circulator as needed by changing

the operating mode using the easy programming button keypad. When the circulator is powered on, the LED will

illuminate and change color based on the operating mode selected. The LED will ash each time a setting is changed.

See diagram below to set pump for desired operating mode. The selection of the right operating curve depends on

the characteristics of the system and the actual ow / head requirements. See Pump Curves on pages 7, 8, 9 & 12

to determine the best operating mode for the system. See cross-reference replacement chart on the back page.

The 0034ePlus has 5 Operating Modes:

• activeADAPT® — Automatic, self-adjusting, proportional pressure, variable speed

(Violet LED)

• Constant Pressure — 5 curve settings of constant pressure, variable speed

(Orange LED)

• Proportional Pressure — 5 curve settings of proportional pressure, variable speed

(Green LED)

• Fixed Speed — Variable xed speed settings (1 - 100%)

(Blue LED)

• 0-10V DC — Analog external input or PWM pulse width modulation

input from building control system, variable speed

(Yellow LED)

Figure 7 - Digital Display Operating Modes

8888 8888 8888

Orange LED (**)

Purple LED (**)

activeADAPT

0-10V

Green LED (**)

Blue LED (**)

min-max

Yellow LED (**)

activeADAPT 0-10V

LED FUNCTION SETTING

activeADAPT (*)

Constant Pressure

(C1 - C2 - C3 - C4 - C5)

Proportional Pressure

(P1 - P2 - P3 - P4 - P5)

Variable Fixed Speed

MIN - MAX (1 - 100%)

0-10V DC

External Input

1) Press the “SET” button for 2 seconds, the LED indicating

the operating status starts ashing quickly.

2) Press the UP or DOWN buttons to select the new operating

mode and the desired value for the constant, proportional

and variable speed curves (See display below).

3) Press the “SET” button to conrm the desired

operating mode and value.

WGPM RPMFT

Constant Pressure

(C1 - C2 - C3 - C4 - C5)

Proportional Pressure

(P1 - P2 - P3 - P4 - P5)

Variable Fixed Speed

MIN - MAX (1 - 100%)

(*) Factory settings

(**) Turns white to indicate the presence of air in the system or red to indicate the presence of an error

C 2

WGPM RPMFT WGPM RPMFT

3P 05

Change the performance of the circulator according to the need, using “SET”, DOWN and UP buttons.

2 s

-7-

10 15 20 25 30 35 40 45 50

Flow Rate Q [GPM]

Head

[ft.]

C2 = 12 ft.

C1 = 6 ft.

C5 = 30ft.

C4 = 24ft.

C3 = 18ft.

0034ePlus

High-Eciency Circulator

Constant Pressure Curves

100

120

140

160

180

10 15 20 25 30 35 40 45 50

Flow Rate Q [GPM]

Power [W]

0034ePlus

High-Eciency Circulator

Constant Pressure Curves

Power Consumption

50 10 15 20 25 30 35 40 45 50 55

Flow Rate Q [GPM]

Head [ft.]

0034ePlus

High-Eciency Circulator

activeADAPT™ Range

activeADAPT

activeADAPT® Mode:

activeADAPT is an operating mode

designed for constant circulation systems.

On this setting, the circulator will sense

changes in system ow and head

conditions and adjust the operating curve

automatically. See activeADAPT operating

range in the chart to the right.

Constant Pressure Mode:

Circulator will vary speed to maintain desired

feet of head constant pressure curve. There are

5 setting options: 6 - 30 feet.

Purple LED

activeADAPT

Orange LED

Green LED

-8- -9-

100

110

120

130

140

150

160

180

170

10 15 20 25 30 35 40 45 50

Flow Rate Q [GPM]

Power [W]

0034ePlus

High-Eciency Circulator

Proportional Pressure Curves

Power Consumption

50 10 15 20 25 30 35 40 45 50 55

Flow Rate Q [GPM]

Head [ft.]

P1 = 8.2 ft.

P2 = 14.6 ft.

P3 = 20.8 ft.

P4 = 24.8 ft.

P5 = 28.6 ft.

0034ePlus

High-Eciency Circulator

Proportional Pressure Curves

Proportional

Pressure Mode:

Circulator will vary speed to maintain

desired feet of head proportional

pressure curve.

There are 5 setting options:

8.2 - 28.6 ft.

Blue LED

min-max

-9-

50 10 15 20 25 30 35 40 45 50 55

120

150

180

Flow Rate Q [GPM]

Power (W)

0034ePlus

High-Eciency Circulator

Variable Fixed Speed Range

Power Consumption

MAX 100%

MIN

50 10 15 20 25 30 35 40 45 50 55

Flow Rate Q [GPM]

Head [ft.]

MAX 100%

Head = 34 ft.

Head = 1 ft.

MIN

0034ePlus High-Eciency Circulator

Variable Fixed Speed Range

Fixed Speed Mode:

Variable xed speed operation.

Setting from 1 - 100% speed.

-10-

External connection for 0-10V DC / PWM signal

WARNING: If there is a need to make external connection (PLC / Pump Controller) it is mandatory to perform the following operations.

1. Remove the four screws (Figure 8 - Ref. 1) attaching the control cover (Figure 8 - Ref. 2).

2. Unscrew a signal input / output cap (Figure 8 - Ref. 3).

3. Remove the green terminal plug (Figure 8 - Ref. 4) from the electronic board (Figure 8 - Ref. 5).

4. Insert the cable (Figure 8 - Ref. 6) in the cable strain relief gland M12x1.5 (Figure 8 - Ref. 7) provided in carton

and screw it to the cover.

5. Strip (Minimum .25”) the ends of the wires, insert them into the connector as shown (Figure 8 - Ref. 4)

and x them with screws (Figure 8 - Ref. 8).

6. Re-connect the terminal plug to the electronic board, replace the control cover and secure it with the screws.

Figure 8 - External connection for 0-10V DC / PWM signal

Step 1

Step 4

Step 2

Step 5

Step 3

Step 6

-11-

0 V Circulator o, not powered

2 V Circulator powered in standby

4 V Circulator on and running

6 V Warning presence (overheating, air)

10 V Alarm presence (Circulator blocked,

under voltage, over temperature)

E1 Pump locked / Loss of step Stop

E2 Under Voltage Stop

E3 Overheating Warning It operates in limited power

E4 Overheating Alarm Stop

E5 Communication with inverter

card is interrupted It works in recover mode

E6 SW cards error. Pumps are

incompatible with each other. It works in recover mode

Analog Output 0-10V DC

The circulator has an analog output signal

feature to indicate the operating status

Errors List

The presence of errors is indicated by a Red LED and

by the “Error Code” on the display.

8888

activeADAPT 0-10V

WGPM RPMFT

Standby

Mode

In the operating mode with external connection

for 0-10V, the “Standby” mode is indicated

by the Yellow LED (ashing slowly) and the

word “Stb” on the display.

Voltage Code Meaning Circulator StatusState

-11-

Analog Input

In the “external input” mode, the circulator accepts either a 0-10VDC voltage signal or a PWM signal. The selection

of the signal type is automatically made by the circulator without operator intervention.

Input 0-10V DC

The circulator operates at variable speed

depending on the DC input voltage.

At voltages below 1.5 V, the circulator is

in “standby” mode. LED will be ashing

yellow in “standby” mode.

At voltages between 2 V and 10 V, the

circulator operates at a variable speed

depending on the voltage:

- 0% for a voltage not exceeding or equal to 2 V

- 50% at 7 V

- 100% for voltages greater than or equal to 10 V

Between 1.5 V and 2 V the circulator can be in “standby” or at minimum speed depending on the previous state

(hysteresis). See diagram.

PWM Input

Circulator operates at variable speed according to digital input duty cycle. PWM digital input is shared with

0-10V DC analog input, the pump will automatically switch between dierent input protocols when it

detects a constant frequency input signal. 0% and 100% PWM inputs are not valid and will be treated

as an analog input.

PWM amplitude must be from 5 to 12V,

frequency between 200Hz to 5kHz

Operations based on PWM input:

- Standby for PWM below 5%

- Min speed for PWM between 9-16%

- Half speed for 50% PWM

- Max speed for PWM in over 90%

Between 5% to 9% PWM the circulator

remainsin standby or run mode according

to minimum threshold.

10V2V1V0.5V

MIN

MAX

SPEED

Input Voltage

IMPORTANT: If the input remains disconnected,

the circulator goes into Standby Mode.

-12-

100

120

140

160

180

106 8 16 1812 14 20 22 24 26 28 30 32 34 36 38 40 44 46 4842 50 5452

Flow Rate Q [GPM]

0-10V

Power

(W)

2V 4V

10V

0034ePlus High-Eciency Circulator

0-10V DC Performance Curves

Power Consumption

Head [ft.]

PWM (Pulse Width Modulation)

2 4 6 80

10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 5452

Flow Rate Q [GPM]

0034ePlus

High-Eciency Circulator

0-10V DC Performance Curves

100%

75%

50%

25%

0-10V

10V

0-10V DC Input Mode:

The circulator will vary its speed and performance based on a 0-10V DC analog signal external input.

0-10V

Yellow LED

-13-

Troubleshooting the error codes:

Listed below are potential diagnostic error codes which will appear on the LED display in case of a malfunction.

Unlocking Procedure: A red LED indicates the circulator is locked or sticking. Disconnect and connect

power supply to start the automatic release process. The circulator makes 100 attempts to restart (process lasts

approximately 15 minutes). Every restart is signaled by a short white ash of the LED. If the locking is not removed

through the automatic release process after 100 attempts to restart the circulator, it goes into standby and the

LED remains red. In this case follow the manual procedure described in the next steps: during any attempt, the

red LED keeps blinking; after that the circulator tries again to start. If the locking is not removed through the

automatic release process (the warning light returns to red), perform the manual steps described below.

1. Disconnect power supply - the warning light switches o.

2. Close both isolating valves and allow cooling. If there are no shut-o devices,

drain the system so that the uid level is beneath that of the circulator.

3. Loosen 4 motor bolts. Remove motor from casing. Carefully pull the rotor/impeller from the motor.

4. Remove impurities and deposits from the impeller and casing.

5. Reinsert the rotor/impeller into the motor.

6. Connect power supply. Check for impeller rotation.

7. If the circulator still doesn’t run it will need to be replaced.

FAULTS CONTROL

PANEL CAUSE SEIDEMERS

The circulator is noisy

LED on Suction pressure is

insufficient - cavitation

Increase the system suction pressure

within the permissible range.

LED on Presence of foreign bodies

in the impeller Disassemble the motor and clean the impeller.

Loud noises of water circulation Flashing white

LED

Air in the system. Circulator

may be air-bound.

Vent the system.

Repeat fill and purge steps.

Circulator is not running although

the electrical power supply is

switched on

LED off

Lack of power supply Verify voltage value of the electric plant.

Verify the connection of the motor.

Circuit breaker might be

tripped

Check circuit breaker at panel

and reset if necessary.

The circulator is defective Replace the circulator.

Overheating

Let the circulator cool down for some minutes.

Then try to restart it. Verify that the water

and ambient temperature are within the

indicated temperature ranges.

LED red

The rotor is blocked Disassemble the motor and clean the impeller.

See unlocking procedure below.

Insufficient supply voltage Verify that the power supply matches

the data on the name plate.

Building does not get warm LED on System may be air-bound Vent system.

Repeat fill and purge steps.

-14-

Technical Menu

Proceed as follows to access the technical menu:

1) Press the UP and DOWN buttons simultaneously for 5s, the message “tECH” will appear in the display.

2) Press the “SET” button and select the parameter to be displayed by pressing the UP or DOWN buttons. (See below).

3} Press the “SET” button and select the desired parameter.

IMPORTANT: After 10 seconds of inactivity, the circulator leaves the technical menu and returns to normal operation.

activeADAPT 0-10V

5 s

8888

WGPM RPMFT

C HE

Parameters Meaning

T 0 Display Firmware version

T 1 Inverter Firmware version

T 2

Unit of measurement shown on the display:

• SI = System International (European)

• IU = Imperial units

T 3 Maximum pump head

T 4 Analog input voltage 0-10V

T 5 “Duty Cycle” PWM input

T 6 Mains voltage

T 7 Internal inverter voltage

T 8 Pump working hours

(in thousands, 0.010 = 10 hours, 101.0 = 101,000 hours)

T 9 Ignitions counter

T 10 Standby counter

T 11 Rotor blocks counter

T 12 Step losses counter

T 13 Under voltages counter

T 14 Over voltages counter

T 15 Counter for missing internal cards communications

-14- -15-

NOTES

LIMITED WARRANTY STATEMENT

Taco, Inc. will repair or replace without charge (at

the company’s option) any Taco product which is

proven defective under normal use within three (3)

years from the date code.

In order to obtain service under this warranty, it

is the responsibility of the purchaser to promptly

notify the local Taco stocking distributor or Taco

in writing and promptly deliver the subject product

or part, delivery prepaid, to the stocking distribu-

tor. For assistance on warranty returns, the pur-

chaser may either contact the local Taco stock-

ing distributor or Taco. If the subject product or

part contains no defect as covered in this war-

ranty, the purchaser will be billed for parts and

labor charges in effect at time of factory exami-

nation and repair.

Any Taco product or part not installed or operated

in conformity with Taco instructions or which has

been subject to misuse, misapplication, the addi-

tion of petroleum-based fluids or certain chemical

additives to the systems, or other abuse, will not

be covered by this warranty.

If in doubt as to whether a particular substance

is suitable for use with a Taco product or part, or

for any application restrictions, consult the

applicable Taco instruction sheets or contact

Taco at (401-942-8000).

Taco reserves the right to provide replacement

products and parts which are substantially similar

in design and functionally equivalent to the

defective product or part. Taco reserves the right

to make changes in details of design, construc-

tion, or arrangement of materials of its products

without notification.

TACO OFFERS THIS WARRANTY IN LIEU OF

ALL OTHER EXPRESS WARRANTIES. ANY

WARRANTY IMPLIED BY LAW INCLUDING

WARRANTIES OF MERCHANTABILITY OR

FITNESS IS IN EFFECT ONLY FOR THE DURA-

TION OF THE EXPRESS WARRANTY SET

FORTH IN THE FIRST PARAGRAPH ABOVE.

THE ABOVE WARRANTIES ARE IN LIEU OF

ALL OTHER WARRANTIES, EXPRESS OR

STATUTORY, OR ANY OTHER WARRANTY

OBLIGATION ON THE PART OF TACO.

TACO WILL NOT BE LIABLE FOR ANY SPECIAL

INCIDENTAL, INDIRECT OR CONSEQUENTIAL

DAMAGES RESULTING FROM THE USE OF

ITS PRODUCTS OR ANY INCIDENTAL COSTS

OF REMOVING OR REPLACING DEFECTIVE

PRODUCTS.

This warranty gives the purchaser specific rights,

and the purchaser may have other rights which

vary from state to state. Some states do not

allow limitations on how long an implied warranty

lasts or on the exclusion of incidental or conse-

quential damages, so these limitations or exclu-

sions may not apply to you.

2021

007-007RP Flange Gasket set

198-213RP Casing ‘O’ Ring

198-3251RP Control Panel Cover (0034ePlus Digital Display)

198-3247RP Terminal Box Cover

198-3185RP Wiring Connector (Green)

198-217RP Terminal Box cover screws (5 per bag)

Replacement Parts List

0034ePlus Pump Replacement Cross Reference

(6-1/2” Flange to Flange Dimension)

Taco Bell & Gossett Armstrong Grundfos Wilo

2400-10

2400-20

2400-30

2400-40

110

111

112

113

009

0010

0011

0012

0013

0014

PL 50

PL 45

PL 36

PL 30

E90 1AAB

Series 60 (601)

Series HV

Series PR

Series HV

Series 100

NRF 45

NRF 36

ECOCirc XL

36-45

E 11

E 10

E 8

E 7

S 25

H 63

H 52

H 51

Astro 290

Astro 280

Astro 210

1050 1B

1050 1 1/4B

Compass ECM

TP(E) 32-40

UP 50-75

UPS 43-100

UPS 50-44

UP 43-75

UP(S) 43-44

UP 26-116

UP(S) 26-99

UP 26-96

UP 26-64

UPS 32-40

UPS 32-80

Magna 32-100

Magna 32-60

Alpha2 26-99

Stratos:

1.25 x 3 – 35

1.25 x 3 – 30

1.25 x 3 – 25

1.25 x 3 – 20

Top S:

1.25 x 15

1.25 x 25

1.25 x 35

1.50 x 20

Top Z:

1.5 x 15

1.5 x 20

NOTE: Flange size and ange to ange dimensions will vary

by competitive model and may require some piping changes.

Taco 0034ePlus-F2 High-Efficiency Circulator Pump User manual

Brand: Taco

Model: 0034ePlus-F2 High-Efficiency Circulator Pump

Type: User manual

The pump's features include:

Simple keypad programming
Digital LED screen display (Watts, GPM, Head, RPM and diagnostic error codes)
Five operating modes to match any system requirements - activeADAPT®, Constant Pressure, Proportional Pressure, Variable Fixed Speed, or 0-10V DC input

Download PDF

report