Hobart HL1400 Installation guide

HL1400
Hobart
Brand
Hobart
Model
HL1400
Type
Installation guide

Hobart HL1400, a top-of-the-line floor model mixer, offers exceptional mixing capabilities for heavy-duty tasks in commercial kitchens. With its powerful motor and durable construction, it can handle large batches of ingredients with ease. The variable speed control allows for precise mixing, from gentle stirring to vigorous blending, making it suitable for a wide range of recipes. The bowl lift feature enables effortless raising and lowering of the bowl, ensuring safe and efficient operation.

Hobart HL1400, a top-of-the-line floor model mixer, offers exceptional mixing capabilities for heavy-duty tasks in commercial kitchens. With its powerful motor and durable construction, it can handle large batches of ingredients with ease. The variable speed control allows for precise mixing, from gentle stirring to vigorous blending, making it suitable for a wide range of recipes. The bowl lift feature enables effortless raising and lowering of the bowl, ensuring safe and efficient operation.

LEGACY+ INSTALLATION GUIDE
For Large Floor Model Mixers: HL600, HL662, HL800 and HL1400
1
VERIFY DATA PLATE
Prior to installation, test the electrical service to ensure that
it matches the specications on the mixer data plate.
DATA PLATE
F48687 (02-22) ©2022 Hobart
SLIDEWAYS
Always refer to procedures as instructed in the Operation Manual for your specic model. Use care when operating, cleaning or performing maintenance.
For additional product resources, please visit www.hobartcorp.com.
Food
Preparation
4
CHECK OIL LEVEL
The mixer is shipped with oil in the transmission. Check oil
level before starting the mixer. If the oil level is below the line
on the oil dipstick, add a small amount of transmission oil
until it returns to the proper level. Contact your local Hobart
Service Oce for the recommended transmission oil.
5
CHECK LUBRICATION
Slideways – To reach these areas, fully lower the bowl
support and remove the apron, which is secured by two
thumb screws. Wipe a thin coat of Lubriplate 630AA on the
bowl pad area of the bowl supports and on each slideway.
Planetary seal – Work a small amount of mineral oil under
the lip of the seal.
Agitator sha – Apply a thin coat of mineral oil.
6
WIRING CHECK
Turn the SPEED dial pointer to STIR. Apply power to the mixer
and run the machine for a few minutes. Also check that the
bowl li raises and lowers.
7
WASH MIXER, BOWLS, AND AGITATORS
Wipe down the mixer with a clean, damp cloth. New mixer
bowls and agitators should be thoroughly washed with hot
water and a mild soap solution, rinsed with either a mild
soda or vinegar solution, and thoroughly rinsed with clear
water before being used.
2
PLACE AND LEVEL THE MIXER
Place the mixer in its operating location. Once in position,
the mixer must be leveled:
1. Remove the two top cover screws and the top cover.
2. Place a level on the top rim of the large pulley. Slide
shims under the base contact surface of the mixer as
required to level it front-to-back and side-to-side.
80 and 140 qt mixers may also be bolted to the floor using
studs. Refer to the mixer’s instruction manual for steps.
3
MAKE ELECTRICAL CONNECTIONS
A hole for 3/4" trade-size conduit is located at the top of the
pedestal. Make electrical connections per the wiring diagram
located on the inside of the top cover.
Electrical and grounding connections must comply with the
applicable portion of the National Electrical Code and/or
other local electrical codes. Disconnect the electrical power
to the mixer and follow lockout/tagout procedures.
AGITATOR SHAFT
PLANETARY SEAL
  • Page 1 1

Hobart HL1400 Installation guide

HL1400
Hobart
Brand
Hobart
Model
HL1400
Type
Installation guide

Hobart HL1400, a top-of-the-line floor model mixer, offers exceptional mixing capabilities for heavy-duty tasks in commercial kitchens. With its powerful motor and durable construction, it can handle large batches of ingredients with ease. The variable speed control allows for precise mixing, from gentle stirring to vigorous blending, making it suitable for a wide range of recipes. The bowl lift feature enables effortless raising and lowering of the bowl, ensuring safe and efficient operation.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents