Page is loading ...
Quick Start Guide
GETTING STARTED WITH YOUR POLAROID
SNAP TOUCH
Step 1: Charge your camera
Plug the cable into a 1amp charge block and into your camera. Make sure the camera is laid flat
on the ground and the cable is not fully extended.
Step 2: Turn your camera on
Press and hold the power button until you hear the welcome sound.
Step 3: Loading paper into the printer
Always load the blue sheet facing down with the gloss of the paper up. Avoid touching the paper
as much as possible by holding from the sides.
Step 4: Holding the camera for a selfie
Step 5: Holding the camera for a picture
Step 6: Take a picture
Press the shutter button to take the picture
Snap Touch Firmware Update
Works with all compatible Apple and Android mobile devices.
Please check your camera version before updating the firmware.
Please note: As the Snap Touch app is being retooled for iOS 11, some functions will be of
limited use until late December 2017, when the entire app will be redesigned for the new
iOS 11 feature set.
It’s time to update your Snap camera. Here’s how:
Step 1:
Check which version of the Snap Touch you currently have.
Warning: Use only the firmware version designed for your model camera. The use of any
other firmware can cause permanent damage to the device.
Snap Touch 1.0 has the power button integrated into the pop-up flash:
Snap Touch 1.2 has the power button next to the pop-up flash:
Step 2:
Download and unzip the correct firmware for your camera
SnapTouch 1.2 Firmware
SnapTouch 1.0 Firmware
Step 3:
Make sure you have an SD card inserted into your Snap, and that your camera is turned on.
Connect your camera to your computer.
Step 4:
When your camera appears on your desktop, save the downloaded file to your Snap.
Step 5:
Turn your camera off, then back on, to restart and begin the update.
Step 6:
While your firmware updates, the LED lights will turn red for 30 seconds.
Step 7:
Your Snap will beep to let you know the update is complete …
Step 8:
… and then it will power off.
Step 9:
Turn on your camera, reconnect your camera to your mobile device via bluetooth and start
printing.
FAQ:
How many sheets can I put in at once?
You can insert up to 10 sheets at a time.
Can i share my pictures from the Polaroid
Snap Touch to social media?
Yes, you either take out the MicroSD card and upload them to your computer or transfer your
photos via Bluetooth through the app.
Is there an option to add a classic white
border?
Yes, you can add a border on the app if you want to take the picture from your phone. If you take
a picture directly from your Polaroid Snap Touch, you can add a white border from the edit menu
on your camera.
Is there an option to add a classic white
border?
Yes, you can add a border on the app if you want to take the picture from your phone. If you take
a picture directly from your Polaroid Snap Touch, you can add a white border from the edit menu
on your camera.
The screen on my camera is frozen and
unresponsive.
Please reset the camera by pressing the Reset button on the bottom of the camera next to the
charging port.
What is the typical battery life of the
camera?
After a full charge, the Polaroid Snap Touch will last for about 15-20 prints.
Why are my prints coming out blank?
Please be sure that the Polaroid Premium ZINK© Paper is inserted properly in the printer. When
loading the paper, the glossy side should be facing up.
How do I connect my Polaroid Snap Touch
through Bluetooth?
Go to your Bluetooth settings on your Smartphone or Tablet. Connect to your Polaroid Snap
Touch.
Open the Polaroid Snap Touch App. Select your Polaroid Snap Touch.
***Please make sure that your Polaroid Snap Touch is on and not connected to any other
Bluetooth devices***
Can I use Zink paper other than Polaroid
Premium ZINK™ Paper?
The Polaroid Snap Touch was designed to work only with Polaroid Premium ZINK™ Paper.
Other papers may not be compatible with this camera.
What MicroSD cards can be used with the
Polaroid Snap Touch?
The Polaroid Snap accepts MicroSD cards upto 128GB.
/