Manufactured under
U.S. Patent No. 5,645,394
WARNINGS
The loading ramp surfaces are sharp. Always wear proper clothing and use care when handling the loading
•
ramps. (Gloves are strongly recommended).
Read and understand all safety and operating instructions before using the loading ramp.
Never
allow
•
anyone unfamiliar with these instructions to use the loading ramps.
Read and understand all safety and operating instructions provided by the manufacturer of the equipment
•
the loading ramp will be used with.
Extreme caution should always be used while loading and unloading your equipment.
•
Do not
exceed the rated capacity of the loading ramp.
•
Do not
exceed the rated capacity of the loading surface (i.e. tailgate). If unknown, contact the manufacturer
•
to find the maximum load capacity.
Never stand in the path of equipment being loaded, and keep all bystanders and children away from
•
loading ramps.
This ramp must be only used for loading and unloading to and from a level and stable surface.
•
Use caution when using ramp in icy or wet conditions. The ramp surface may become slippery.
•
Do not
use this loading ramp to load live animals.
•
Do not
use loading ramps as a bridge, scaffolding, or any other use for which it is not intended or designed.
•
If ramp is bowing while loading or unloading your equipment, which indicates an overload condition,
•
remove the equipment immediately.
Do not
attempt to load or unload any power equipment with its motor running.
•
Failure to follow these warnings may result in property damage and/or serious bodily injury.
•
OPERATION
We suggest that you drill 7/16" diameter holes through the support bars (3) into the tail gate or truck bed
so that the pins can be inserted as a safety device in holding ramps in place. To prevent kick back of the
loading ramp, always attach cam buckle straps to bumper of truck and center of ramp pulling strap tight.
Align individual ramps to correctly correspond to your wheel track. Always remove key, turn fuel off, and
set parking brake after loading vehicle.
SAFETY
Be sure to read and follow all safety instructions and warnings. Failure to follow these instructions may
•
result in damage to the product and/or serious personal injury.
Danger of serious personal injury exists. Serious personal injury can occur when using a loading ramp.
•
Never
attempt to ride any vehicle up or down the loading ramp.
•
Look for a wall or a depression to reduce the loading angle, the lower the ramp angle the easier the
•
loading of the vehicle will be.
Park the vehicle on flat, firm, grassy terrain.
•
Set the emergency brake and chock the tires of the loading vehicle to prevent any movement while
•
loading and unloading the equipment.
Center loading ramp on the loading surface with support bars on top of the loading surface.
•
Make sure ramps are aligned at the proper distance apart so that the tires of the equipment being loaded
•
are centered on the ramp.
To prevent kick back, always attach cam buckle straps between the bumper of the truck and the center of
•
loading ramp, pulling strap tight.
Roll or winch equipment up or down the ramp.
•
Before each use, always check for any worn, loose, or damaged parts on the loading ramp. If any damage
•
is present,
DO NOT USE THE RAMP
.
Periodically check the fasteners to make sure they are still tight and in place.
•
Keep ramp surface clean by occasionally cleaning with water and any mild detergent.
•
Do not add to or try to modify the loading ramp in any way. Any modifications will void any warranties as
•
well as affect the structural integrity of the ramp itself.
14 GAUGE STEEL FOLDING
LOADING RAMP
Model 10-84
1000lbs distributed weight capacity - single.
•
2000lbs distributed weight capacity - double.
•
Compact storage.
•
One person loading.
•
1
2
4
5
6
7
7
8
9
10
12
11
3
14
Ohio Steel Ind., Columbus, OH 43224 U.S.A.
Visit our website: www.ohiosteel.com
For missing parts or questions call 1-800-652-2321
If this product fails due to a defect in material or workmanship within one year from the date of purchase,
Ohio Steel Industries will at its option repair or replace it free of charge.
Proof of purchase required
for
all
warranty claims.
This warranty does not cover:
Repairs necessary because of operator abuse or negligence.
•
Equipment used for commercial or rental purposes.
•
Contact Ohio Steel Industries to arrange for product repair, or return this product to place of purchase for
replacement.
This warranty gives you specific legal rights, and you may also have other rights which may vary from state
to state.This warranty applies only while this product is in use in the United States.
When ordering repair parts always give the following information,
PRODUCT NAME, MODEL NUMBER, PART NUMBER, and PART DESCRIPTION.
LIMITED ONE-YEAR WARRANTY
Assembly
Step 1. Attach support bars (3) to ramp top (1) with bolts (9), flat washers (10), lock washers (11), and
hex nuts (12).
Step 2. Slide support bar pads (5) onto bars as shown.
Note: Apply a little soapy water inside support bar pad, this allows the pad to slide onto the bar easier.
Step 3. Invert ramp bottom (2) so that flanges face up. Place ramp top (1) inside the ramp bottom so that the side
holes of each are in line.
Step 4. Secure both side by inserting 1/2" hex bolt (6) through 1/2" flat washer (7), ramp bottom, ramp top, another
flat washer (7) and tighten with lock nut (8) as shown. NOTE: DO NOT OVER TIGHTEN. Ramp must be
able to swivel open and shut.
10-84 Rev C
2008_05
-
1
-
2
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
YuTrax TX108 User guide
-
YuTrax TX104 User manual
-
YuTrax TX500 User manual
-
YuTrax TX138 Operating instructions
-
Harbor Freight Tools 96514 User manual
-
YuTrax TX195 User manual
-
-
Haul-Master 94057 Owner's manual
-
-
Landoll 317D User manual
