Harbor Freight Tools Three_Jaw Puller Set 3 Pc User manual

Brand: Harbor Freight Tools

Model: Three_Jaw Puller Set 3 Pc

Type: User manual

Harbor Freight Tools Three_Jaw Puller Set 3 Pc is a versatile tool designed for removing bearings, pulleys, and other components from shafts. It features three different sizes of jaws (3", 4", and 6") to accommodate a wide range of applications. The reversible jaws ensure a proper grip on various surfaces, while the lead screw provides a secure hold on the shaft. With a maximum pulling force of over 2.5 tons for the 3" and 4" jaws and over 3.5 tons for the 6" jaws, this puller set is capable of handling even the most stubborn components.

GEAR PULLER - THREE JAW

Model

08832

Distributed Exclusively by Harbor Freight Tools

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight

Tools.

For technical questions please call 1-800-444-3353

Size Maximum Pulling Force

3” > 2.5 Ton

4” > 2.5 Ton

6” > 3.5 Ton

SAVE THIS INSTRUCTION SHEET

Keep this instruction sheet for the safety warnings and precautions, assembly, operating, inspec-

tion, maintenance and cleaning procedures. Keep this instruction sheet and the receipt in a safe and

dry place for future reference.

UNPACKING

When unpacking, check to make sure all parts shown on the photo are included. If any parts

are missing or broken, please call Harbor Freight Tools at the number shown on the front page of this

instruction sheet as soon as possible.

GENERAL SAFETY WARNINGS AND PRECAUTIONS

DO NOT USE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read

warning labels on prescriptions to determine if your judgment or reexes are impaired while taking

drugs. If there is any doubt, do not attempt to use this product.

USE EYE PROTECTION. Wear ANSI approved safety impact eye glasses when using this

product. ANSI approved safety impact eye glasses are available from Harbor Freight Tools.

DRESS SAFELY. Non-skid footwear or safety shoes should be used when working with this

product. Do not wear loose clothing or jewelry as they can become caught in moving parts. Wear

Page 2SKU 08832 For technical questions, please call 1-800-444-3353.

a protective hair covering to prevent long hair from becoming caught in moving parts. If wearing a

long-sleeve shirt, roll sleeves up above elbows.

CHECK FOR DAMAGED PARTS. Before using this product, carefully check that it will

operate properly and perform its intended function. Check for damaged parts and any other

conditions that may affect the operation of this product. Replace or repair damaged or worn

parts immediately. When servicing, use only identical replacement parts. Only use accessories

intended for use with this product. Approved accessories are available from Harbor Freight Tools.

MAINTENANCE: For your safety, service and maintenance should be performed regularly by a

qualied technician.

USE THE RIGHT PRODUCT FOR THE RIGHT JOB. There are certain applications for which

this product was designed. Do not use small equipment, tools or attachments to do the work of

larger industrial equipment, tools or attachments. Do not use this product for a purpose for which

it was not intended.

The warnings and cautions discussed in this instruction sheet cannot cover all possible conditions

and situations that may occur. It must be understood by the operator that common sense and

caution are factors which cannot be built into this product, but must be supplied by the operator.

OPERATING INSTRUCTIONS

The Jaws are reversible to ensure proper grip on a wide range of jobs. Depending on the depth

of the pulling job, keep either the longer or shorter ends of the Jaws down to grip the underside

of the bearing/pulley.

Hand tighten the Lead Screw through the bearing/pulley and onto the shaft from which the bear-

ing/pulley is to be removed. Once in position, wrench tighten the Lead Screw until the bearing/

pulley is completely free of the shaft.

INSPECTION, MAINTENANCE, AND CLEANING

Before each use, inspect the general condition of the Gear Puller. Check misalignment, binding

of moving parts, broken parts, and any other condition that may affect its safe operation. If any

malfunction of the parts occur, discontinue using the Gear Puller immediately and have the

problem corrected before further use. Do not use damaged equipment.

Keep the Gear Puller clean for better and safer product performance. To clean, use a mild

detergent or mild solvent. Then dry.

Note:

Replacement parts are not available for this item.

Harbor Freight Tools Three_Jaw Puller Set 3 Pc User manual

Harbor Freight Tools Three_Jaw Puller Set 3 Pc User manual

Harbor Freight Tools Three_Jaw Puller Set 3 Pc User manual

Related papers

Other documents