1
When using your telephone equipment, basic safety precautions should
always be followed to reduce the risk of fire, electric shock and injury, including
the following:
1. Read and understand all instructions.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
4. Do not use this product near water (for example, near a bath tub, kitchen
sink, or swimming pool).
5. Do not place this product on an unstable surface. The product may fall,
causing serious damage.
6. Slots and openings in the Handset and Base Unit are provided for ventilation.
To protect it from overheating, these openings must not be blocked by
placing the product on a soft surface such as a bed, sofa or rug. This prod-
uct should never be placed near or over a radiator or heat register. This
product should not be placed in a built-in installation where proper ventila-
tion is not provided.
7. This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power
supply to your home, consult your dealer or local power company.
8. Do not allow anything to rest on the power cord. Do not install this product
where the cord might be damaged by anyone walking on it.
9. Never push objects of any kind into this product through the slots in the
Handset and Base Unit as they may touch dangerous voltage points or
short out parts that could result in a risk of fire or electric shock. Never spill
liquid of any kind on the product.
10. To reduce the risk of electric shock, do not disassemble this product, but
take it to an authorized service facility. Opening or removing cabinet parts
other than specified access doors may expose you to dangerous voltages
or other risks. Incorrect reassembling can cause electric shock when the
appliance is subsequently used.
11. Do not overload wall outlets and extension cords as this can result in the
risk of fire or electric shock.
12. Unplug this product from the wall outlet and contact VTECH under the following
conditions:
A. When the power supply cord or plug is damaged or frayed.
B. If liquid has been spilled into the product.
C. If the product has been exposed to rain or water.
D. If the product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions,
because improper adjustment of other controls may result in damage
and will often require extensive work by an authorized technician to restore the
product to normal operation.
E. If the product has been dropped and the cabinet has been damaged.
Important Safety Instructions
2
F. If the product exhibits a distinct change in performance.
13. Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
14. Do not use this or any cordless telephone to report a gas leak in the vicinity
of the leak.
VTECH COMMUNICATIONS INC.
CUSTOMER SERVICE: 1-800-595-9511. In Canada VTech Telecommunications
Canada Ltd. at 1-800-267-7377.
BEFORE USING YOUR ip 5850 SYSTEM, CAREFULLY PEEL OFF THE PRO-
TECTIVE FILM COVERING THE DISPLAYS.
Important Safety Instructions
3
Your ip 5850 is an advanced cordless telephone set, capable of supporting two
Handsets. This manual is designed to familiarize you with this cordless
telephone. We strongly recommend you read the manual before using your
phone.
Introduction
4
Parts Check List
1. Base Unit
2. Handsets
3. Handset Charger
4. Base AC Power Adapter
5. Telephone Line Cord
6. Belt Clips
7. Base Wall Mounting Bracket
8. Charger Wall Mounting Bracket
9. User’s Manual
10. Batteries
Battery x 2
To purchase replacement batteries, visit us on the web at www.vtechphones.com
or call VTech Communications, Inc. at 1-800-595-9511. In Canada, call VTech
Telecommunications Canada Ltd. at 1-800-267-7377.
NOTE: Use only VTech batteries (part number 80-5808-00-00) or equivalent
NiMH rechargeable batteries.
5
1. Antenna
2. Earpiece
3. Volume Control
4. CID (Scroll Down)
5. On (Flash)
6. Dialing Keys (0-9, *, #)
7. Redial (Pause)
8. Speakerphone
9. LCD Display
10. Select (Menu)
11. Phonebook (Scroll Up)
12. Headset Jack (2.5mm)
13. Off (Clear)
14. Intercom
15. Mute (Delete)
The Handset Layout
6
The Base Unit Layout
1. Rec/Memo
2. Time/Set
3. Change
4. Cradle Contacts
5. Menu
6. In Use LED
7. Charging LED
8. Page
9. Microphone
10. Volume Control
11. Repeat/Slow
12. Skip/Quick
13. Delete
14. Message Boxes (PLAY/STOP)
15. Answering Machine Control
(On/Off)
16. DC Connector Jack
17. Telephone Jack
7
Connecting Power to Base Unit/Handset Charger
1. Plug the AC power adapter into an electrical outlet, and the DC connector
into the bottom of the Base Unit.
2. Choose the location for your Handset Charger, and plug its power supply
into an electrical outlet.
Getting Started
Setup
8
Setup
Getting Started
Installation of Battery in Handset
Follow the steps below:
1. Place the new battery in the Hand-
set with the positive and negative
poles aligned in the battery com-
partment.
2. Replace the battery compartment cover
by sliding it upwards.
3. If the new battery is not already charged,
place the Handset in its Charger or Base
Unit, and allow it to charge for 10-12
hours. After initial charge, a maintenance
charge of 8 hours should be sufficient.
Charging of the Handset Battery
The Handset of your cordless telephone is powered by a rechargeable battery. It
charges automatically whenever the Handset is in its charger or Base Unit.
You should charge the battery for 10-12 hours when you first receive your
phone.
You will know the battery needs charging when:
• The low battery message is displayed:
• The Handset seems completely dead, the LCD
is completely clear and does not activate when
you press the keys.
NOTE: When in LOW BATTERY mode, the keypad sounds, backlighting and
speakerphone features will not work. When your battery has been charged,
your features will return to their normal function.
IMPORTANT:
1. Do not dispose of the battery in a fire, it might may explode.
2. Do not open or mutilate the battery. Toxic substances may be released,
causing harm to eyes or skin.
3. Exercise care in handling battery in order to prevent an accidental short of
the charge contacts, potentially causing the battery to overheat.
4. Do not dispose of this battery into household garbage, it should be properly
recycled.
5. Do not charge the battery with other electrical devices.
9
Connecting to Phone Line
Plug one end of the telephone line cord into the jack at the bottom of the Base
Unit. Then plug the other end of the cord into the wall jack.
Setup
Getting Started
Check Battery Indicator
If you receive a check battery warning, it indicates one of the following:
1. There is no battery in your Handset. You’ll need to install a battery into your
Handset (see Installation and Charge of Battery in Handset section on the
previous page.)
2. The battery has been installed incorrectly. Please
reinstall (see Installation of Battery in Handset)
and/or the diagram in the battery compartment on
the Handset.
Checking for Dial Tone
After the battery is charged, press ON on the Handset. The word PHONE
will appear on the Handset display, and you will hear a dial tone. If not, see In
Case of Difficulty.
Tone/Pulse Selection
Your phone is preset for tone dialing. See Handset Settings for details.
CAUTION: Use only the VTech power supply provided with your telephone.
IMPORTANT:
FOR MAXIMUM PERFORMANCE OF
YOUR CORDLESS TELEPHONE SYSTEM:
1. Choose a central location for your Base
Unit.
2. Install your Base Unit and Extension Hand-
sets away from electronic equipment,
such as personal computers, television
sets and microwave ovens.
3. In locations where there are multiple
cordless telephones, separate Base
Units as far away as possible.
4. Install your telephone equipment away
from heat sources and sunlight.
5. Avoid excessive moisture, dust or ex-
treme cold.
10
Wall Mounting
The Wall Mount brackets are designed for use on standard wall mount plates
only. Wall mounting is optional.
1. Plug the AC adapters into electrical outlets. Then plug the DC connector of
the Base power adapter to the connector jack at the bottom of the Base Unit.
2. Connect the telephone line cord to the jack at the bottom of the Base Unit,
and the other end to the wall jack.
3. Line up the tabs on the wall mount adapters with the holes at the bottom of the
Base Unit/back of the Handset Charger. Snap the wall mount bracket firmly
in place.
4. Mount the Base Unit/Handset Charger on the wall. Position the Base Unit/
Handset Charger so that the mounting studs will fit into the holes on the wall
mount bracket. Slide Base Unit/Handset Charger down on the mounting
studs until it locks into place.
Getting Started
11
Handset and Base Indicators
Basic Operation
• Turns on when the microphone is muted.
• Turns on when there are new call log entries.
• Turns on when the ringer is muted.
• Low battery indicator or charging indicator.
Handset LEDs
LED Description
.
Base LEDs
LED Description
IN USE
CHARGING
PLAY/STOP
1, 2, 3
ON/OFF
• On when the phone is off hook.
• Flashes when an extension phone is off hook.
• On when the Handset is charging in the cradle.
• Flashes when new messages are in the corresponding
mailbox.
• On when only old messages are in the corresponding
mailbox.
• On when the answering system is on.
• LED is on when in handsfree mode.
SPEAKER
Handset Icons
Icon Description
MUTE
NEW
12
Handset Operation
Basic Operation
Making Calls
• Press ON (or SPEAKER to use the Handset
Speakerphone feature). Dial the phone
number.
-OR-
Dial the phone number first, then press ON
(or SPEAKER).
• Press OFF to end your call.
Answering Calls
• Press ON, SPEAKER or any dialing keys.
• Press OFF to end your call.
Adjust the Handset Volume
• The volume control is on the left edge of the
Handset. During a call, press
or key to
adjust the listening volume to a comfortable
level. When you reach the maximum or
minimum setting, a double-beep will sound.
NOTE: The procedure is the same for the Handset
earpiece, Speakerphone and Headset.
Flash Function
• You can use your ip 5850 with services such as
Call Waiting. When you receive a call-waiting
signal, simply press the ON/FLASH key to
switch to the new call. Press ON/FLASH again
to switch back to the original call.
NOTE: Use ON/FLASH to access other phone
company subscriber services, as described by
your provider.
Redial Function
• Press REDIAL/PAUSE to display the last
telephone number dialed from the Handset
(up to 32 digits). Use
or to scroll
through the 5 previously dialed numbers.
When the beginning or the end of the redial
list is reached, a double-beep will sound.
• Pressing OFF will exit the redial review list.
• When the desired number is reached, press ON or SPEAKER to dial.
• When the desired entry displays, press DELETE to delete it. A confirmation
tone will sound.
NOTE: If the redial memory is empty, and REDIAL is pressed, a double-beep will
sound.
13
Basic Operation
Handset Operation
Mute Function
• During an active call, pressing the MUTE/
DELETE key will disable the microphone.
The screen will display MICROPHONE
MUTED briefly:
• Press MUTE/DELETE again to return to
normal 2-way conversation. MICRO-
PHONE ON will display briefly.
Intercom Call
• From the idle (OFF) mode, press INT. The
Handset will display:
• The other Handset will ring and the screen
will display:
• Press INT or SPEAKER to answer the
intercom call. The screens will display:
• Press INT or OFF on either Handset to end
the call.
NOTE: If the other Handset is out of range,
or on an external call, when you intercom it,
the display of the first handset will show:
Call Forward and Call Transfer
An external call can be forwarded or
transferred from one Handset to the other
Handset. The difference between forward
and transfer depends on if the sending Hand-
set needs to talk with the receiving Handset,
before the external call is actually sent to the
other Handset.
14
Basic Operation
Handset Operation
Call Forward
• A Handset (HS1) on an external call can
forward it to the other Handset (HS2) by
pressing and holding the INT key. The
display of HS1 will initially show:
• HS2 can press ON to answer the call.
NOTE: If HS2 does not answer the call in about
30 seconds, the external call will be returned to
HS1 and the display will show:
If the returned call is not answered within another 30
seconds, the external call will end automatically.
Call Transfer
• A Handset (HS1) on an external call can forward it to the other Handset (HS2)
by pressing the INT key.
NOTE: The external call is put on hold automatically.
• HS2 will ring, showing an intercom call.
• HS2 can answer the intercom call by pressing ON.
• Intercom call link is established while the external call is still on hold. HS1
may discuss the external call with HS2.
• When HS1 presses OFF, the external call is then transferred to HS2. CALL
TRANSFERRED will display on HS1 briefly.
NOTE: If there is no answer on HS2, HS1 can reconnect to the held call by
pressing ON.
Conference Call
It is possible to establish a conference between
two Handsets and the external line.
If a Handset already has a connection to the
external line, the other Handset can join the call by
pressing ON, a conference will be immediately
established. Both Handsets will show:
Base Operation
From the Base Unit, you can use PAGE key to
locate the Handsets for 60 seconds.
• When the Handset is in idle, press PAGE. The
Handsets will display:
• To end the page at the Base, press PAGE
again.
• To end the page at the Handset, press ON,
SPEAKER or any dialing keys.
15
Basic Operation
Phonebook Operation
Your ip 5850 can store up to 50 numbers with names in memory. Each memory
location can hold up to 32 digits for the number and 16 characters for the name.
NOTE: The Handsets share a common phonebook, which is stored in the Base. This
means that entries inserted by one Handset are available for both Handsets, and if one
deletes a phonebook entry, it will disappear from both Handsets.
When one Handset is accessing the phonebook, the other Handset cannot
access it at the same time. If this is attempted, NOT AVAILABLE AT THIS TIME
will display on the second Handset.
Storing a New Entry
• Press SEL.
• With Phonebook selected, press SEL
again.
• Press
to select STORE. Press SEL.
• You will be prompted to ENTER NUMBER.
Use the dialing keys to enter the number
you wish to store in the phonebook. Press
the MUTE.DEL key to backspace and
make corrections. Press SEL.
• You will then be prompted to ENTER
NAME. Use the dialing keys to spell the
name. Press SEL.
• You will hear a confirmation tone, and
the new phonebook entry will display
briefly.
NOTES:
• If the phonebook is full, the Handset will
display PHONEBOOK IS FULL.
• You can also press REDIAL.PAUSE, then
or to scroll to the previously dialed
number from the redial list which you want
to store in the phonebook. Press SEL.
• While entering numbers, press and
hold REDIAL.PAUSE to add pauses
if necessary.
• If there is a duplicate number in the
phonebook, the display will show:
16
Phonebook Operation
Basic Operation
Each press of a particular key causes characters to be displayed in the follow-
ing order:
Characters by number of key presses
Key
123456789
space 1
ABC2abc
DEF3 de f
GH I 4 g h i
JKL5 j k l
MNO6 mn o
PQRS7pq rs
TUV8 t u v
WX Y Z 9w x y z
0
?!/()
#' ,-.&
1
2
3
4
5
6
7
8
9
0
#
Reviewing/Dialing from the Phonebook
• Press SEL. With Phonebook in the first line,
press SEL again. With the REVIEW in the first
line, press SEL again.
- OR -
With the Handset idle, press and the Hand-
set jumps directly into the phonebook review
mode. The first phonebook entry will be dis-
played.
• Scroll through the phonebook entries using
or keys or enter first character of the name
to be searched (using the digit keys) and con-
tinue navigating using the or as scroll
keys, until you reach the entry to be dialed.
NOTE: When reviewing the phonebook, the sec-
ond line of the display will show the phone num-
ber, up to 16 digits. For numbers longer than 16
digits, only the first 13 digits will be shown. Press
or # to scroll the phone number to see the
additional digits.
17
Phonebook Operation
Basic Operation
• Press ON or SPEAKERPHONE, to dial the
number.
NOTE: If there are no entries in the phonebook,
when it is accessed, PHONEBOOK IS EMPTY
will display
Editing a Phonebook Entry
• Follow the two steps in Reviewing/Dial-
ing from the phonebook (on page 16) to
reach the entry to be edited.
• Press SEL to enter number edit mode.
• Press MUTE.DEL to backspace then press
the digit keys to correct the number. Press
and hold REDIAL.PAUSE to add pauses if
necessary.
You can also press REDIAL.PAUSE, then
or to scroll to the previously dialed number
from redial list which you want to store in the
phonebook. Press SEL.
• Press SEL to confirm the number and enter
name edit mode.
• Press MUTE.DEL key to backspace and use
the digit keys to enter the correct name.
• Press SEL to confirm the change. A confirma-
tion tone will sound.
Delete a Phonebook Entry
• Follow the two steps in Reviewing/Dialing
from the Phone Book (on page 16) to reach
the entry to be deleted.
• Press MUTE.DEL key to delete the entry.
A confirmation tone will sound.
• The Handset will then move to the next entry,
if any.
18
Basic Operation
Call Log (Caller ID - Call Waiting)
Caller ID - Call Waiting ID
Your ip 5850 is capable of displaying the number of the calling party before you
answer the phone (Caller ID). If the number is contained in the phonebook, the
name of the caller will also be displayed. It is also capable of displaying Caller ID
information in conjunction with a Call Waiting alert signal (Call Waiting Caller ID).
With Call Waiting Caller ID, the Caller ID data is displayed so you can decide
whether to answer the incoming call, or continue with your current conversation.
Your ip 5850 can hold up to 50 CID entries.
NOTES ABOUT CALLER ID & CALL WAITING CALLER ID
These are subscription services, provided by most regional telephone
service providers. You must subscribe to these services to get the benefits
of these features. If you do not subscribe to Caller ID services, you can
still use your ip 5850 and the other features it offers.
Due to regional incompatibilities, Caller ID information may not be
available for every call you receive. In addition, the calling party may
intentionally block their name and/or phone number from being sent.
• As new Caller ID/Call Waiting ID records are
received, your Handset displays will alert you
to the new Caller ID records, for example:
• After you review all new Caller ID records,
the NEW call indication will be turned off
and the screen will show:
• If the call log is full, the oldest entry is
deleted to make room for the new call. If the
call log is empty when you try to enter to
Call Log review, the following message is
displayed:
Reviewing Caller ID
You can review the Caller ID record via the
menu as described below, or by pressing the
key in idle (quick access key) whereby the
Handset jumps directly to the Caller ID review.
• In idle mode, press SEL to enter the menu.
• Press key to scroll to CALL LOG option.
19
Call Log (Caller ID - Call Waiting)
Basic Operation
• Press SEL again. Use or to scroll through
the Call Log entries. When the beginning or
the end of the Call Log is reached, a double
beep will sound.
Storing a Caller ID
• Follow the steps in Reviewing Caller ID to scroll
to the record to be stored.
• To view alternate dialing sequences, press
the # key repeatedly. The screen will cycle
through the various dialing options (1 + area
code + number, area code + number, 1 + num-
ber, number only.) Press SEL to store the dis-
played number.
• If the Caller ID contains both name and number,
the Caller ID will be stored after pressing SEL.
• If the caller ID does not contain a name, you
will be prompted to EDIT NAME and the screen
will show:
• If the caller ID does not contain a number, you
will be prompted to EDIT NUMBER, and the
screen will show:
• You will hear a confirmation tone then the
screen will display:
• If both name and number are missing, for
example as in a private listing, the request
will be rejected with the message:
• If the phone number already exists in the
phonebook, the entry will not be stored, and
the screen will show:
• If the phonebook is full, the screen will show:
Dialing from Caller ID
• Follow the steps in Reviewing Caller ID to
scroll to the entry to be dialed.
20
Call Log (Caller ID - Call Waiting)
Basic Operation
Deleting Caller ID
• Follow the steps in Reviewing Caller ID to
scroll to the record to be deleted.
• Press DELETE key to delete the desired
record. A confirmation tone will sound and
the previous Caller ID record will be
displayed on the screen.
• To delete all the Caller ID records, press and
hold the DELETE key. The screen will ask
you DELETE ALL CALLS? Press SEL for
confirmation. Or, press OFF to return to the
CID record previously displayed.
• To change how the number will be dialed,
(1 + area code + number, area code + num-
ber, 1 + number, number only.) press # re-
peatedly. The screen will cycle through the
dialing options. Press ON or SPEAKER key
to dial the number.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
/