Craftsman 919.769062 User manual

Brand: Craftsman

Model: 919.769062

Category: High-pressure cleaners

Type: User manual

This manual is also suitable for

D28234

Owner’s Manual

5.5 Horsepower

2400 PSI

2.2 GPM

PRESSURE WASHER

• Safety Guidelines

• Assembly

• Operation

• Maintenance

• Storage

• Troubleshooting

• Repair Parts

• Espaoñol

Model No.

919.769062

CAUTION: Read the Safety Guidelines

and All Instructions Carefully Before

Operating.

D28234 Rev. 1 8/4/03

Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.

Visit our Craftsman website: www.sears.com/craftsman

2- ENG

D28234

TABLE OF CONTENTS

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

SPECIFICATION CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

SAFETY GUIDELINES- DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . .3

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . .3-7

BOX CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-13

MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13-16

STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17-18

TROUBLESHOOTING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . .18-20

REPAIR PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21-36

HOW TO ORDER REPAIR PARTS . . . . . . . . . . . . . . . . . . . .Back Cover

WARRANTY

FULL ONE YEAR WARRANTY ON CRAFTSMAN HIGH PRESSURE WASHER

For one year from the date of purchase, when this Craftsman High Pressure

Washer is maintained and operated according to the instructions in the owner’s

manual, Sears will repair, free of charge, any defect in material and workmanship.

If your Craftsman Pressure Washer is used for commercial or rental purposes, this

warranty applies only for 90 days from the date of purchase.

FULL TWO YEAR WARRANTY ON CRAFTSMAN ENGINE

For two years from the date of purchase, when this Craftsman engine is maintained

and operated according to the instructions in the owner’s manual, Sears will repair,

free of charge, any defect in material and workmanship.

If your Craftsman engine is used for commercial or rental purposes, this warranty

applies only for 90 days from the date of purchase. This warranty does not cover

expendable items such as spark plugs and air filters, which become worn during

normal use.

Repairs necessary because of operator abuse or negligence, including damage

resulting from no water being supplied to pump or failure to maintain the

equipment according to the instructions contained in the owner’s manual, are not

covered under warranty.

WARRANTY SERVICE IS AVAILABLE BY RETURNING THE HIGH PRESSURE

WASHER TO THE NEAREST SEARS SERVICE CENTER THROUGHOUT THE

UNITED STATES. This warranty gives you specific legal rights and you may also

have other rights, which vary from state to state.

Sears, Roebuck and Co., D/817 WA, Hoffman Estates, IL 60179

3- ENG

D28234

SPECIFICATION CHART

Model No. 919-769062

Pressure Washer

Pressure 2400 PSI

Flow Rate 2.2 GPM

Cleaning Units (PSI x GPM) 5280

Engine

RPM 3600

Rated Horsepower 5.5

Spark Plug Gap .030” (0.76mm)

Gasoline Capacity .29 gallons (1.1 liters)

Oil .58 quarts ( .55 liters) capacity SAE 30 weight

indicates an imminently hazardous situation which, if not avoided, will

result in death or serious injury.

indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

indicates a potentially hazardous situation which, if not avoided,may

result in minor or moderate injury.

used without the safety alert symbol indicates potentially hazardous

situation which, if not avoided, may result in property damage.

This manual contains information that is important for you to know and understand.

This information relates to protecting YOUR SAFETY and PREVENTING EQUIP-

MENT PROBLEMS. To help you recognize this information, we use the symbols

below. Please read the manual and pay attention to these sections.

SAFETY GUIDELINES / DEFINITIONS

This product may not be equipped with a spark arresting

muffler. If the product is not equipped and will be used

around flammable materials, or on land covered with materials such as

agricultural crops, forest, brush, grass, or other similar items, then an ap-

proved spark arrester must be installed and is legally required in the state of

California. It is a violation of California statutes section 130050 and/or sec-

tions 4442 and 4443 of the California Public Resources Code, unless the

engine is equipped with a spark arrester, as defined in section 4442, and

maintained in effective working order. Spark arresters are also required on

some U.S. Forest Service land and may also be legally required under other

statutes and ordinances.

Engine exhaust contains chemicals known, in certain

quantities, to cause cancer, birth defects or other

reproductive harm.

CONSUMER SAFETY INFORMATION

4- ENG

D28234

IMPORTANT SAFETY INSTRUCTIONS

Read Operators Manual. Do not operate equipment until you

have read operators Manual for Safety, Assembly, Operation, and

Maintenance Instructions.

RISK OF EXPLOSION OR FIRE

HAZARD

WHAT CAN HAPPEN

HOW TO PREVENT IT

• Spilled gasoline and it’s vapors can be-

come ignited from cigarette sparks,

electrical arcing, exhaust gases, and hot

engine components such as the muffler.

• Shut off engine and allow it to cool before

adding fuel to the tank.

• Use care in filling tank to avoid spilling fuel.

Move pressure washer away from fueling area

before starting engine.

• Heat will expand fuel in the tank which

could result in spillage and possible fire

explosion.

• Keep maximum fuel level ½” below top of

tank to allow for expansion.

• Operating the pressure washer in an ex-

plosive environment could result in a fire.

• Operate and fuel equipment in well ventilated

areas free from obstructions. Equip areas with

fire extinguisher suitable for gasoline fires.

• Materials placed against or near the pres-

sure washer can interfere with its proper

ventilation features causing overheating

and possible ignition of the materials.

• Never operate pressure washer in an area

containing dry brush or weeds.

• Muffler exhaust heat can damage painted

surfaces, melt any material sensitive to

heat (such as siding, plastic, rubber, or

vinyl), and damage live plants.

• Always keep pressure washer a minimum of

four feet away from surfaces (such as houses,

automobiles, or live plants) that could be dam-

aged from muffler exhaust heat.

• Improperly stored fuel could lead to acci-

dental ignition. Fuel improperly secured

could get into the hands of children or

other unqualified persons.

• Store fuel in an OSHA approved container,

in a secure location away from work area.

• Use of acids, toxic or corrosive chemicals,

poisons, insecticides, or any kind of flam-

mable solvent with this product could re-

sult in serious injury or death.

• Do not spray flammable liquids.

• Breathing exhaust fumes will cause serious

injury or death!

• Operate pressure washer in a well ventilated

area. Avoid enclosed areas such as garages,

basements, etc.

• Never operate unit in a location occupied by

humans or animals.

• Some cleaning fluids contain substances

which could cause injury to skin, eyes, or

lungs.

• Use only cleaning fluids specifically recom-

mended for high pressure washers. Follow

manufacturers recommendations. Do not

use chlorine bleach or any other corrosive

compound.

RISK TO BREATHING

HAZARD

WHAT CAN HAPPEN

HOW TO PREVENT IT

READ AND SAVE THESE INSTRUCTIONS

5- ENG

D28234

• Fuel or oil can leak or spill and could

result in fire or breathing hazard, serious

injury or death can result. Fuel or oil leaks

will damage carpet, paint or other

surfaces in vehicles or trailers.

• If pressure washer is equipped with a fuel

shut-off valve, turn the valve to the off

position before transporting to avoid fuel

leaks. If pressure washer is not equipped

with a fuel shut-off valve, drain the fuel from

tank before transporting. Only transport fuel

in an OSHA approved container. Always

place pressure washer on a protective mat

when transporting to protect against dam-

age to vehicle from leaks. Remove pressure

washer from vehicle immediately upon arrival

at your destination.

• Your washer operates at fluid pressures

and velocities high enough to penetrate

human and animal flesh, which could

result in amputation or other serious injury.

Leaks caused by loose fittings or worn or

damaged hoses can result in injection

injuries. DO NOT TREAT FLUID

INJECTION AS A SIMPLE CUT! See a

physician immediately!

• Never place hands in front of nozzle.

• Direct spray away from self and others.

• Make sure hose and fittings are tightened

and in good condition. Never hold onto the

hose or fittings during operation.

• Do not allow hose to contact muffler.

• Never attach or remove wand or hose

fittings while system is pressurized.

• Do not use acids, gasoline, kerosene, or

any other flammable materials in this

product. Use only household detergents,

cleaners and degreasers recommended for

use in pressure washers.

• Wear protective clothing to protect eyes

and skin from contact with sprayed

materials.

• Use of acids, toxic or corrosive chemicals,

poisons, insecticides, or any kind of flam-

mable solvent with this product could re-

sult in serious injury or death.

RISK OF INJURY OR PROPERTY DAMAGE

WHEN TRANSPORTING OR STORING

HAZARD

WHAT CAN HAPPEN

HOW TO PREVENT IT

RISK TO FLUID

INJECTION

HAZARD

WHAT CAN HAPPEN

HOW TO PREVENT IT

• Injuries can result if system pressure is not

reduced before attempting maintenance or

disassembly.

RISK OF

CHEMICAL

BURN

HAZARD

WHAT CAN HAPPEN

HOW TO PREVENT IT

• To relieve system pressure, shut off engine,

turn off water supply, and pull gun trigger

until water stops flowing.

• Use only hoses and accessories rated for

pressure higher than your pressure

washer's p.s.i.

6- ENG

D28234

• Reactive force of spray will cause

gun/wand to move, and could cause the

operator to slip or fall, or misdirect the

spray. Improper control of gun/wand can

result in injuries to self and others.

• Do not overreach or stand on an unstable

support. Grip gun/wand firmly with both

hands. Expect the gun to kick when trig-

gered.

• If proper starting procedure is not

followed, engine can kickback causing

serious hand and arm injury.

• If engine does not start after two pulls,

squeeze trigger of gun to relieve pump

pressure. Pull starter cord slowly until

resistance is felt. Then pull cord rapidly

to avoid kickback and prevent hand or

arm injury.

• The spray gun/wand is a powerful clean-

ing tool that could look like a toy to a

child.

• Keep children away from the pressure

washer at all times.

• Contact with hot surfaces, such as

engines exhaust components, could

result in serious burn.

• During operation, touch only the control

surfaces of the pressure washer. Keep

children away from the pressure washer at all

times. They may not be able to recognize the

hazards of this product.

• Spray directed at electrical outlets or

switches, or objects connected to an

electrical circuit, could result in a fatal

electrical shock.

• Unplug any electrically operated product

before attempting to clean it. Direct spray

away from electric outlets and switches.

RISK OF UNSAFE OPERATION

HAZARD

WHAT CAN HAPPEN

HOW TO PREVENT IT

• Unsafe operation of your pressure washer

could lead to serious injury or death to

you or others.

• Do not use chlorine bleach or any other

corrosive compound.

• Become familiar with the operation and con-

trols of the pressure washer.

• Keep operating area clear of all persons,

pets, and obstacles.

• Do not operate the product when fatigued

or under the influence of alcohol or drugs.

Stay alert at all times.

• Never defeat the safety features of this

product.

• Do not operate machine with missing,

broken, or unauthorized parts.

• Never leave wand unattended while unit is

running.

RISK OF

ELECTRICAL SHOCK

HAZARD

WHAT CAN HAPPEN

HOW TO PREVENT IT

RISK OF HOT

SURFACES

HAZARD

WHAT CAN HAPPEN

HOW TO PREVENT IT

7- ENG

D28234

The powerful spray from your pressure washer is capable of causing

damage to surfaces such as wood, glass, automobile paint, auto

striping and trim, and delicate objects such as flowers and shrubs. Before spraying,

check the item to be cleaned to assure yourself that it is strong enough to resist damage

from the force of the spray. Avoid the use of the concentrated spray stream except for

very strong surfaces like concrete and steel.

Operating without flow of water will result in equipment damage. Operating the pressure

washer with water supply shutoff will void your warranty. You should never run this pres-

sure washer for more than 2 minutes without pulling the trigger to allow cool water to

enter the pump and the heated (recirculated) water to exit.

RISK OF INJURY FROM SPRAY

HAZARD

WHAT CAN HAPPEN

HOW TO PREVENT IT

• High velocity fluid spray can cause

objects to break, propelling particles at

high speed.

• Light or unsecured objects can become

hazardous projectiles.

• Always wear ANSI approved Z87 safety

glasses.Wear protective clothing to protect

against accidental spraying.

• Never point wand at, or spray people or

animals.

• Always secure trigger lock when wand is not

in service to prevent accidental operation.

• Never permanently secure trigger in pull

back (open) position.

BOX CONTENTS

Handle Part No. D22316

with Screws Part No. D22901

Bagged Parts

Nozzle Cleaning

Kit

English/

Spanish

Operator’s

Manual

Engine Frame and

Wheel Assembly

High Pressure

Hose

Part No. D22166

Chemical Hose

Part No. H140

Engine Oil

Spray Gun

Part No. 17780

Multi-Adjustable Spray Wand

Part No. D23314

Accessories Panel Part No. D21865

Knobs

Part No.

16471

Saddle

Bolts Part

No. D23196

Allen Wrench Part No. 16797

Cleaning Tool Part No. NCT001

8- ENG

D28234

5. To Assemble Accessories Panel

a. Remove top screws on

handle assembly.

b. Loosen bottom screws on

handle assembly.

c. Place grooves in accessories

panel assembly onto screws

and slide panel assembly into

place.

d. Place screws (removed

earlier) into the top holes and

secure accessories panel

assembly to handles. Do not

overtighten.

Loosen

Screws

Remove

2. Connect wand to gun. Tighten

securely.

3. Attach high pressure hose to gun.

Tighten securely.

ASSEMBLY

1. Place handle assembly onto frame

and connect handle to frame.

NOTE: Knobs are assembled to

inside of frame.

9- ENG

D28234

OPERATION

High

Pressure

Pump

Engine

High

Pressure

Hose

Spray

Gun

Multi-

Adjustable

Spray Wand

Chemical

Hose

Hand

Grip

Air Filter

Fuel Valve

Lever

Choke

Control

Throttle

Control

Chemical Hose: Feeds cleaning

agents into the pump to mix with the

pressurized water. See How To Apply

Chemicals/Cleaning Solvents in

Operation section of this manual.

ENGINE

Choke Control: Opens and closes

carburetor choke valve

Throttle Control Lever: Controls

engine speed.

Starter Grip: Pulling starter grip

operates recoil starter to crank engine.

Fuel Valve Lever: Opens and closes

connection between fuel tank and

carburetor.

PRESSURE WASHER

High Pressure Pump (located inside

the shroud): Increases the pressure of

the water supply.

Engine: Drives the high pressure

pump.

High Pressure Hose: Carries the

pressurized water from the pump to

the gun and spray wand.

Spray Gun: Connects with spray wand

to control water flow rate, direction,

and pressure.

Multi-Adjustable Spray Wand: Has a

spray nozzle which adjusts from a

pencil stream (0°) to a wide angle fan

spray (40°). The spray can be adjusted

by twisting the nozzle clockwise

and/or counterclockwise. Also, the

high and low pressure settings can be

controlled by moving the nozzle in and

out. See How To Use Spray Wand

paragraph in this section.

READ THIS OPERATION MANUAL AND SAFETY RULES BEFORE OPERATING

YOUR UNIT. Compare the illustrations with your unit to familiarize yourself with

the location of various controls and adjustments. Save this manual for future

reference.

10- ENG

D28234

HOW TO USE SPRAY WAND:

Your pressure washer is equipped with

a multi-adjustable spray wand with

both high and low pressure settings.

The high pressure setting is for

cleaning and rinsing, the low pressure

setting is for applying chemicals or

cleaning solutions to surfaces.

When using the high

pressure setting, DO

NOT allow the jet-like spray to come

in contact with unprotected skin,

eyes, or with any pets or animals.

Serious injury can occur.

Risk of injection or

injury to person. DO

NOT direct discharge stream toward

persons.

For high pressure operation, pull back

the nozzle of the multi-adjustable

spray wand as shown.

TO ADJUST PRESSURE

The pressure setting is preset at the

factory to achieve optimum pressure

and cleaning. If you need to lower the

pressure, it can be accomplished by

these methods.

1. Back away from the surface to

be cleaned. The further away you

are, the less the pressure will be

on the surface to be cleaned.

2. Rotate the nozzle at the end of

the multi-adjustable spray wand

to widen the fan spray. The

wider fan spray will minimize the

pressure on the surface to be

cleaned.

DO NOT attempt to

increase pump

pressure. A higher pressure setting

than the factory set pressure may

damage pump.

HOW TO USE

IMPORTANT: Read and understand

how to use the pressure washer

before operating.

PRESSURE WASHER

TERMINOLOGY

PSI: Pounds per Square Inch. The unit

of measure for water pressure. Also

used for air pressure, hydraulic

pressure, etc.

GPM: Gallons Per Minute. The unit of

measure for the flow rate of water.

CU: Cleaning Units. GPM multiplied by

PSI.

Bypass Mode: In Bypass Mode, the

pump is recirculating water because

the trigger of the spray gun is not

pulled. If unit is left in bypass mode for

more than two (2) minutes, the water

temperature will rise to a dangerous

level and could damage internal

components of the pump. Any

damage to pump due to these causes

will not be covered under warranty.

DO NOT allow your

unit to operate in

bypass mode for more than two

minutes at any time. Overheating of

pump can cause damage to pump.

Thermal Relief Valve: In an effort to

prevent extreme damage, pumps are

equipped with a thermal relief valve.

This valve will open when the

temperature inside the pump rises too

high. This valve will then release a

gush of water in an effort to lower the

temperature inside the pump.

Immediately after this occurs, the

valve will close. The thermal relief

valve is part of the pump and is not

visible to the user.

Chemical Injection System: Mixes

cleaners or cleaning solvents with the

water to improve cleaning effectiveness.

Water Supply: All pressure washers

must have a source of water. The

minimum requirements for a water

supply are 20 PSI and 5 gallons per

minute.

11- ENG

D28234

The nozzle at the end of the multi-

adjustable spray wand can be rotated

to change the high pressure spray

pattern from a narrow jet to a 40º fan

shape, as shown. Markings have been

placed on the nozzle to help you

select the spray pattern.

For low pressure operation, extend the

nozzle of the multi-adjustable spray

wand as shown.

HOW TO APPLY CHEMICALS

AND CLEANING SOLVENTS

Applying chemicals or cleaning

solvents is a low pressure operation.

NOTE: Use only soaps and

chemicals designed for pressure

washer use. Do not use bleach.

To Apply chemicals:

1. Press chemical hose onto barbed

fitting located near high pressure

hose connection of pump as

shown.

2. Place other end of chemical hose

with filter on it into container holding

chemical/cleaning solution. NOTE:

The chemical/water ratio is 7:1, for

every 7 gallons of water pumped 1

gallon of chemical/cleaning solution

will be used.

3. Install low pressure (black) nozzle

into quick connect fitting of spray

wand, see How To Use Spray Wand

paragraph in this section.

4. After use of chemicals, place

chemical hose into container of

clean water and draw clean water

through chemical injection system

to rinse system thoroughly. If

chemicals remain in the pump it

could be damaged. Pumps

damaged due to chemicals will not

be covered under warranty.

NOTE: Chemicals and soaps will not

siphon when spray wand is in the high

pressure setting.

Barb fitting

TO SHUT DOWN

IMPORTANT: Read and understand

how to shut down the pressure

washer before operating.

1. If you have applied chemicals,

place chemical hose into container

of clean water and draw clean

water through chemical injection

system to rinse system thoroughly.

NOTE: Failure to do so could

cause damage to the pump.

2. Turn engine off by placing the

throttle control in the OFF

position.

NOTE: NEVER turn the water off

with the engine running.

3. Turn the fuel valve to the OFF

position if engine will not be

restarted soon.

4. Turn water source off.

5. Pull trigger on spray gun to relieve

any water pressure in hose or

spray gun.

6. See Storage section in this

manual for proper storage

procedures.

40º fan spray

narrow jet stream

12- ENG

D28234

3. Verify the filter screen is in water

inlet of pump. NOTE: Cone side

faces out.

4. Connect high pressure hose to

pump outlet.

5. Connect water source to pump

inlet.

NOTE: Water source must provide a

minimum of 5 gallons per minute at

20 p.s.i.

6. If you are applying a chemical or

cleaning solution, See How To

Siphon Chemicals/Cleaning

Solvents in Operation section of

this manual.

7. Turn water source on.

NOTE: Failure to do so could cause

damage to the pump.

Water

Source

High

Pressure

Hose

Filter Screen

BEFORE STARTING

Read and understand all Important

Safety Instructions in the front of

this manual and the following

Cautions and Warnings before

starting the pressure washer.

• Never fill fuel tank completely.

Fill tank to 1/2" below bottom of

filler neck to provide space for

fuel expansion. Wipe any fuel

spillage from engine and

equipment before starting

engine.

• Never fill fuel tank indoors.

Never fill fuel tank when engine

is running or hot. Do not smoke

when filling fuel tank.

• Never run engine indoors or in

enclosed, poorly ventilated

areas. Engine exhaust contains

carbon monoxide, an odorless

and deadly gas.

• Never turn water supply off

while pressure washer engine is

running or damage to pump will

result.

• DO NOT use hot water, use cold

water only.

• DO NOT stop spraying water for

more than two minutes at a

time.

1. In a well ventilated outdoor area

add fresh, high quality, unleaded

gasoline with a pump octane

rating of 86 or higher. Do not

overfill. Wipe up spilled fuel before

starting the engine. Refer to

Engine Owners Manual for correct

procedure.

2. Remove filler cap/dipstick and

add engine oil (supplied) to

engine. NOTE: There will be a

slight amount of oil in the engine

from factory testing. Always check

oil level before each start-up.

Filler cap/dipstick

13- ENG

D28234

If the engine does

not start after two

pulls, pull the trigger to relieve the

pressure.

11. If the choke was used to start the

engine, move the choke lever to

the OFF position.

12. Depress trigger on gun to start

water flow. NOTE: Stand on a

stable surface and grip

gun/spray wand firmly with both

hands. Expect the gun to kick

back when triggered.

13. Release trigger to stop water flow.

14. Adjust nozzle spray for the task

being performed. See How To

Use Spray Wand instructions in

this section.

DO NOT let hoses

come in contact with

very hot engine muffler during or

immediately after use of your

pressure washer.

MAINTENANCE

When performing maintenance, you may be exposed to hot

surfaces, water pressure, or moving parts that can cause

serious injury or death!

Before performing any maintenance or repair, disconnect spark plug wire,

let engine cool and release all water pressure. The engine contains

flammable fuel. DO NOT

smoke or work near open flames while performing

maintenance.

To ensure efficient operation and longer life of your pressure washer, a routine

maintenance schedule should be prepared and followed. If the pressure washer is

used in unusual conditions, such as high-temperatures or dusty conditions, more

frequent maintenance checks will be required.

8. Turn fuel valve to the ON position,

1/4 turn counterclockwise.

9. Move the choke control lever to

the CHOKE ON position and

the throttle control to the FAST

position. NOTE: No choke is

needed to start a warm engine.

10. Pull starter grip slowly until you

feel resistance, then pull briskly.

Return starter grip gently. Pull

rope with a rapid full arm stroke.

Let rope rewind slowly. Repeat if

necessary.

Fuel Valve Knob

Choke

Control

Throttle

Control

14- ENG

D28234

4. If the oil level is low, fill to the edge

of the oil filler hole with the SAE

10W-30 oil.

NOTE: Other viscosities shown in the

chart may be used when the average

temperature in your area is within the

recommended range.

CUSTOMER RESPONSIBILITIES TABLE

MAINTENANCE TASK

PRESSURE WASHER

ENGINE

check/clean inlet screen

check high pressure hose

check soap and chemical

hose and filter

check gun and wand for leaks

check oil level

change oil

check air filter

clean/replace spark plug

prepare for storage

Before

each use

Every 25

hours or

yearly

Every 50

hours or

yearly

Every 100

hours or

yearly

Prepare unit for storage if it is to remain idle for longer

than 30 days

ENGINE

To Check Oil

1. Shut down engine and place on a

level surface.

2. Remove filler cap/dipstick and wipe

it clean.

3. Insert and remove the filler

cap/dipstick without screwing it

into the filler neck. Check the oil

level shown on the dipstick.

Filler cap/dipstick

Oil Filler

Cap/Dipstick

Upper Limit

Lower Limit

-20 0 20 40 60 80 100

-30 -20 -10 0 10 20 30 40

STARTING TEMPERATURES RANGE

ANTICIPATED BEFORE NEXT OIL CHANGE

SAE Viscosity Grades

Synthetic 5W-30, 10W-30

15- ENG

D28234

Air Cleaner

A dirty air cleaner will restrict air flow to

the carburetor and cause poor engine

performance. Inspect the filter each

time the engine is operated. Clean the

filter more frequently if the engine is

operated in very dusty areas.

NOTICE: Operating the engine without

a filter, will allow dirt to enter the

engine, causing rapid engine wear. This

type of damage is not covered under

the warranty.

Inspect

1. Press the latch tabs on the top of

the air cleaner cover and remove

the cover. Check the filter to be

sure it is clean and in good

condition.

2. Reinstall the filter and air cleaner

cover.

Cleaning

1. Tap the filter several times on a

hard surface to remove dirt or

blow compressed air [not

exceeding 30 psi (207kPa, 1.2

kg/cm

] through the filter from the

clean side that faces the engine.

Never try to brush off dirt.

Brushing will force dirt into the

fibers.

2. Wipe dirt from the air cleaner body

and cover using a moist rag. Be

careful to prevent dirt from

entering the air duct that leads to

the carburetor.

To Change Oil

Drain the engine oil when the engine is

warm. Warm oil drains quickly and

completely.

1. Turn the fuel valve to the OFF

position, 1/4 turn clockwise.

2. Place a suitable container next to

the engine to catch the used oil.

3. Remove filler cap/dipstick and

drain the oil into the container by

tipping the engine toward the oil

filler neck.

NOTE: Please dispose of used motor

oil in a manner that is compatible with

the environment. It is recommended to

take used oil in a sealed container to

your local recycling center or service

station for reclamation. Do not throw it

in the trash or pour it on the ground or

down a drain.

4. With the engine in a level position,

fill to the upper limit mark on the

dipstick with SAE 10W-30 oil.

Engine oil capacity is 0.58 quart

(.055 liter). NOTE: Other

viscosities shown in the chart in

the “To Check Oil” paragraph may

be used.

5. Replace the oil filler cap/dipstick

securely.

Oil Filler

Cap/Dipstick

Upper Limit

Lower Limit

Oil Filler Neck

Air Cleaner Body

Filter

Air

Cleaner

Cover

Latch

Tabs

Lower

Tabs

Air Duct

16- ENG

D28234

3. Pull trigger on gun handle to

relieve any water pressure.

4. Disconnect the wand from the

gun.

5. Remove the nozzle from the end

of the wand with the 2mm allen

wrench provided as shown.

6. Clean the nozzle using the nozzle

cleaner provided or a straightened

paper clip. Insert into the nozzle

end and work back and forth until

obstruction is removed.

7. Direct water supply into nozzle

end to backflush loosened

particles for 30 seconds.

8. Reconnect spark plug wire.

9. Reassemble the nozzle to the

wand. Tighten securely to prevent

leaks.

10. Reconnect wand to gun and turn

on water supply.

11. Start pressure washer and place

wand into high pressure setting to

test.

WAND

If the nozzle becomes clogged with

foreign materials, such as dirt,

excessive pressure may develop. If the

nozzle becomes partially clogged or

restricted, the pump pressure will

pulsate. Clean the nozzle immediately

using the nozzle kit supplied and the

following instructions:

1. Shut off the pressure washer and

turn off the water supply.

2. Disconnect spark plug wire.

Clean and Replace Spark Plug

Change the spark plug every 100 hours

of operation or once each year,

whichever comes first. This will help

your engine to start easier and run

better.

Resistor

.030” (0.76 MM)

Wire Gauge

PUMP

This screen filter should be checked

periodically and cleaned if necessary.

1. Remove filter by grasping end and

removing it from water inlet of

pump as shown.

2. Clean filter by flushing it with water

on both sides.

3. Re-insert filter into water inlet of

pump. NOTE: Cone side faces

out.

NOTE: Do not operate pressure

washer without filter properly installed.

Filter Screen

17- ENG

D28234

ENGINE

IMPORTANT: It is important to prevent

gum deposits from forming in essential

fuel system parts such as the

carburetor, fuel filter, hose or tank

during storage. Also, experience

indicates that alcohol-blended fuels

(called gasohol or using ethanol or

methanol) can attract moisture which

leads to separation and formation of

acids during storage. Acidic gas can

damage the fuel system of an engine

while in storage. To avoid engine

problems, the fuel system should be

emptied before storage of 30 days or

longer. Never use engine or carburetor

cleaner products in the fuel tank or per-

manent damage may occur.

Engine Preparation

1. First add a fuel stabilizer to the

fuel tank.

2. Run pressure washer for a full 5

minutes to allow fuel stabilizer to

enter the fuel system.

While preparing the

engine make sure

water supply is turned on and

flowing to the unit. NEVER run unit

without water supply running

through pump. Failure to do so will

cause pump damage.

3. Next shut off engine and

disconnect the water supply.

4. Disconnect the spark plug wire

and remove the spark plug.

5. Add one teaspoon of oil through

the spark plug hole.

6. Place rag over spark plug hole and

pull the recoil a few times to

lubricate the combustion chamber.

7. Replace the spark plug, but do not

connect the spark plug wire.

PUMP

1. Drain all water from high pressure

hose, coil it, and store it in cradle

of the pressure washer handle.

2. Drain all water from spray gun and

spray wand by holding spray gun

in a vertical position with nozzle

end pointing down and squeezing

trigger. Store in gun/hose holder.

3. Store chemical hose, high pressure

hose, spray gun, and spray wand

so they are protected from dam-

age, such as being run over.

It is recommended that you follow

these steps to protect the internal seals

of the pressure washer when STORING

THE UNIT FOR MORE THAN 30 DAYS

AND/OR WHEN FREEZING

TEMPERATURES ARE EXPECTED.

*RV antifreeze needs to be run through

the pump as outlined in the steps

below.

4. Obtain a funnel, six ounces of *RV

antifreeze, and approximately 36

inches of garden hose with a male

hose connector attached to one

end.

Use only RV

antifreeze. Any other

antifreeze is corrosive and can

damage pump.

5. Disconnect spark plug wire.

6. Connect 36 inch length of hose to

water inlet of pump.

7. Add *RV antifreeze to hose as

shown.

STORAGE

18- ENG

D28234

8. Pull engine starter rope slowly

several times until antifreeze

comes out of high pressure hose

connection of pump.

9. Remove short hose from water

inlet of pump.

10. Reconnect spark plug wire.

*Windshield washer fluid may also be

used

TROUBLESHOOTING GUIDE

PROBLEM

CAUSE

CORRECTION

Engine will not

start

1. No fuel.

2. Pressure builds up after

two pulls on the recoil

starter or after initial use.

3. Not choked.

4. Spark plug wire not

attached.

5. Choke lever in the

"Choke" position on a

"hot" engine or an engine

that has been exposed to

thermal heat for a long

period of time.

6. Fuel valve closed

1. Add Fuel.

2. Squeeze gun trigger to

relieve pressure.

3. Choke engine, place engine

in the choke position.

4. Attach spark plug wire.

5. Move choke to the "No

Choke" position.

6. Move the fuel valve knob to

the "Open" position.

No or low

pressure

(initial use)

1. Wand not in high

pressure.

1. See How to Use Spray

Wand paragraph in the

Operation Section.

2. Low water supply.

2. Water supply must be at

least 5 GPM @ 20 PSI.

3. Leak at high pressure

hose fitting.

3. Tighten. Apply sealant tape

if necessary.

4. Nozzle obstructed.

5. Water filter screen

clogged.

5. Remove and clean filter.

4. See Spray Wand

paragraph in the

Maintenance section for

the correct procedure.

19- ENG

D28234

6. Air in hose.

6. Turn off the engine, then the

water source. Disconnect

the water source from the

pump inlet and turn the

water source on to remove

all air from the hose. When

there is a steady stream of

water present, turn water

source off. Reconnect water

source to pump inlet and

turn on water source.

Squeeze trigger to remove

remaining air.

7. Choke lever in the

"Choke" position.

8. Throttle control lever is

not in the "Fast" position.

9. High pressure hose is too

long.

7. Move choke to the "No

Choke" position.

8. Move throttle control lever to

the "Fast" position.

9. Use high pressure hose

under 100 feet.

PROBLEM

CAUSE

CORRECTION

No or low

pressure

(initial use)

(continued)

6. Chemical build up in

chemical injector.

Will not draw

chemicals

1. Wand not in low

pressure.

2. Chemical filter clogged.

3. Chemical screen not in

chemical

4. Chemical too thick

5. Pressure hose is too long

2. Clean filter.

3. Insure end of chemical hose

is fully submerged into

chemical.

4. Dilute chemical. Chemical

should be the same

consistency as water.

5. Lengthen water supply hose

instead of high pressure

hose.

6. Have parts cleaned or

replaced by AWSC.

1. See Spray Wand paragraph

in the Maintenance section

for the correct procedure.

20- ENG

D28234

PROBLEM

CAUSE

CORRECTION

No or low

pressure (after

period of nor-

mal use.)

Water leaking

at gun/wand

connection

Water leaking

at pump

1. Worn seal or packing.

2. Worn or obstructed

valves.

3. Worn unloader piston.

1. Worn or broken o-ring.

2. Loose hose connection.

1. Loose connections.

2. Piston packings worn.

3. Worn or broken o-rings.

4. Pump head or tubes

damaged from freezing.

1. Have replaced by AWSC.

2. Have replaced by AWSC.

3. Have replaced by AWSC.

1. Check and replace.

2. Tighten.

1. Tighten.

2. Have replaced by AWSC.

3. Have replaced by AWSC.

4. Have replaced by AWSC.

1. Nozzle obstructed.

2. See Spray Wand paragraph

in the Maintenance section

for the correct procedure.

Pump Pulsates

Page is loading ...

Craftsman 919.769062 User manual

Brand: Craftsman

Model: 919.769062

Category: High-pressure cleaners

Type: User manual

This manual is also suitable for

D28234

Download PDF

report

in other languages

español: Craftsman 919.769062 Manual de usuario

Craftsman 919.769062 User manual

This manual is also suitable for

Craftsman 919.769062 User manual

in other languages

Related papers

Other documents