Sharp LC-15L1U-S Operation Manual User manual

LC-15L1U

LIQUID CRYSTAL TELEVISION

TÉLÉVISEUR ACL

TELEVISOR CON PANTALLA

DE CRISTAL LÍQUIDO

TELEVISOR DE CRISTAL

LÍQUIDO

LC-15L1U

OPERATION MANUAL

MODE D’EMPLOI

MANUAL DE OPERACIÓN

MANUAL DE OPERAÇÃO

ENGLISH

FRANÇAIS

ESPAÑOL

PORTUGUÊS

SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07430-2135

SHARP CORPORATION

Printed on 100% post-consumer recycled paper.

Imprimé sur 100% de papier recyclé.

Impreso en 100% de papel reciclado de postconsumo.

Papel 100% Reciclado-Cuidado do Meio Ambiente.

Printed in Japan

Imprimé au Japon

Impreso en Japón

Impresso no Japão

TINS-B124WJZZ

04P02-###

ENGLISH

1

LC-15L1U

LIQUID CRYSTAL TELEVISION

OPERATION MANUAL

ENGLISH

IMPORTANT INFORMATION

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS PRODUCT TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage”

within the product’s enclosure that may be of

sufficient magnitude to constitute a risk of electric

shock to persons.

The exclamation point within a triangle is intended to

alert the user to the presence of important operating

and maintenance (servicing) instructions in the

literature accompanying the product.

IMPORTANT:

To aid reporting in case of loss or theft, please record the TV’s model

and serial numbers in the space provided. The numbers are located at

the rear of the TV.

U.S.A. ONLY

Model No.:

Serial No.:

2

IMPORTANT INFORMATION (Continued)

WARNING: FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly

approved by the manufacturer could void the user’s authority to operate this equipment.

“Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electrical

Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding

system of the building, as close to the point of cable entry as practical.”

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE

SLOT, FULLY INSERT.

U.S.A. ONLY

This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these

materials may be regulated due to environmental considerations. For disposal or recycling information, please contact

your local authorities or the Electronic Industries Alliance: www.eia.org

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the operation manual, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try

to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

U.S.A. ONLY

The device’s label or the user manual contains this statement (or equivalent): “To prevent radio interference to the

licensed service, this device is intended to be operated indoors and away from windows to provide maximum shielding.

Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.”

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must

accept any interference, including interference that may cause undesired operation of the device.

ENGLISH

3

CONTENTS

Page

IMPORTANT INFORMATION................................... 1

DEAR SHARP CUSTOMER ..................................... 4

IMPORTANT SAFETY PRECAUTIONS .................. 4

REGARDING BATTERY CARE ............................... 7

CORRECT USE OF THE PRODUCT ....................... 9

SUPPLIED ACCESSORIES ................................... 10

PREPARATION....................................................... 11

MAIN UNIT PART NAMES ..................................... 14

WIRELESS CENTER PART NAMES ..................... 17

REMOTE CONTROL .............................................. 18

POWER ................................................................... 19

Turning the Main Power on and off .................. 19

Viewing with a Home AC Wall Outlet ............... 21

EZ SETUP (WITH AUTO CLOCK SETTING) ........ 22

EZ Setup during the First Power On ................ 22

SETTING THE CLOCK ........................................... 24

AUTO CLOCK Setting ....................................... 24

MANUAL CLOCK Setting.................................. 26

TV SIGNALS IN YOUR REGLON .......................... 27

BATTERY CHARGE AND TRANSMISSION

SETTING .............................................................. 28

Battery Charge .................................................. 28

Transmission Setting ......................................... 28

BASIC OPERATION ............................................... 31

Turning on Power .............................................. 31

Standby.............................................................. 31

Switching TV/VIDEO [AV1/AV2/AV3/AV4]

Modes ............................................................. 32

Sound Volume ................................................... 33

Changing Channels ........................................... 34

SELECTING MENU ITEMS .................................... 35

ADJUSTMENTS ...................................................... 36

Adjusting SLEEP TIMER Settings .................... 36

Adjusting BRIGHTNESS Settings ..................... 37

Adjusting PICTURE FLIP Settings.................... 38

Adjusting PRESET Settings .............................. 39

Adjusting LANGUAGE Settings ........................ 40

Adjusting VIDEO ADJUST Settings .................. 41

SETUP ............................................................... 43

Adjusting BLUE SCREEN Settings................... 45

Adjusting CLOSED CAPTION Settings ............ 46

Adjusting V-CHIP Settings ................................ 47

CONNECTION SYSTEM WITH VARIOUS WAYS

OF BEING USED ................................................. 54

Examples of Various Uses ................................ 54

Connecting System Chart of LC-15L1U ........... 55

Method of Connecting External Equipment ...... 56

Method of Using the Video Controller .............. 57

Watching Played back Image from External

Equipment....................................................... 58

Connecting a Home Video Game System, etc.

(AV-IN4) .......................................................... 59

How to Use Video 1 Output .............................. 60

Monitor Output for Picture and Sound Output

from AV-IN2/OUT Terminal ............................ 61

TROUBLESHOOTING ............................................ 62

SPECIFICATIONS................................................... 65

DIMENSIONAL DRAWINGS .................................. 66

CALLING FOR SERVICE ....................................... 67

LIMITED WARRANTY ............................................ 67

Page

4

DEAR SHARP CUSTOMER

Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years

of trouble-free operation of your product, please read the Important Safety Precautions carefully before

using this product.

IMPORTANT SAFETY PRECAUTIONS

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if

improperly handled. This product has been engineered and manufactured with the highest priority on safety. However,

improper use can result in electric shock and/or fire. In order to prevent potential danger, please observe the following

instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your

LCD color TV product, please read the following precautions carefully before using the product.

■ Read instructions—All operating instructions must be read and understood before the product is operated.

■ Keep this manual in a safe place—These safety and operating instructions must be kept in a safe place for future

reference.

■ Observe warnings—All warnings on the product and in the instructions must be observed closely.

■ Follow instructions—All operating instructions must be followed.

■ Attachments—Do not use attachments not recommended by the manufacturer. Use of inadequate attachments

can result in accidents.

■ Power source—This product must operate on a power source specified on the specification label. If you are not

sure of the type of power supply used in your home, consult your dealer or local power company. For units

designed to operate on batteries or another power source, refer to the operating instructions.

■ Power cord protection—The power cords must be routed properly to prevent people from stepping on them or

objects from resting on them. Check the cords at the plugs and product.

■ If the AC adapter is misplaced or needs to be replaced, obtain the same type of adapter from a SHARP service

center or your dealer.

■ Overloading—Do not overload AC outlets or extension cords.

Overloading can cause fire or electric shock.

■ Entering of objects and liquids—Never insert an object into the product through vents or openings. High voltage

flows in the product, and inserting an object can cause electric shock and/or short internal parts. For the same

reason, do not spill water or liquid on the product.

■ Servicing—Do not attempt to service the product yourself. Removing covers can expose you to high voltage and

other dangerous conditions. Request a qualified service person to perform servicing.

■ Repair—If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a quali-

fied service person to perform repairs.

a.When the power cord or plug is damaged.

b.When a liquid was spilled on the product or when objects have fallen into the product.

c. When the product has been exposed to rain or water.

d.When the product does not operate properly as described in the operating instructions.

Do not touch the controls other than those described in the operating instructions. Improper adjustment of

controls not described in the instructions can cause damage, which often requires extensive adjustment work by

a qualified technician.

e.When the product has been dropped or damaged.

f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the

product needs servicing.

■ Replacement parts—In case the product needs replacement parts, make sure that the service person uses

replacement parts specified by the manufacturer, or those with the same characteristics and performance as the

original parts. Use of unauthorized parts can result in fire, electric shock and/or other danger.

■ Safety checks—Upon completion of service or repair work, request the service technician to perform safety checks

to ensure that the product is in proper operating condition.

■ Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the product according

to the method recommended by the manufacturer.

■ Polarization—This AC adapter may be equipped with a polarized alternating current line plug (a plug having one

blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are

unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your

electrician to replace your obsolete outlet.

Do not defeat the safety purpose of the polarized plug.

ENGLISH

5

IMPORTANT SAFETY PRECAUTIONS (Continued)

■ The Liquid Crystal panel is a very high technology product with 921,600 thin film transistors, giving you fine picture

details.

Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red.

Please note that this does not affect the performance of your product.

■ Cleaning—Unplug the power cord from the AC outlet before cleaning the prod-

uct. Use a damp cloth to clean the product. Do not use liquid cleaners or aerosol

cleaners.

■ Water and moisture—Do not use the product near water, such as bathtub,

washbasin, kitchen sink and laundry tub, swimming pool and in a wet basement.

■ Stand—Do not place the product on an unstable cart, stand, tripod or table.

Placing the product on an unstable base can cause the product to fall, resulting

in serious personal injuries as well as damage to the product. Use only a cart,

stand, tripod, bracket or table recommended by the manufacturer or sold with the

product. When mounting the product on a wall, be sure to follow the manufactur-

er’s instructions. Use only the mounting hardware recommended by the manu-

facturer.

■ When relocating the product placed on a cart, it must be moved with utmost

care. Sudden stops, excessive force and uneven floor surface can cause the

product to fall from the cart.

■ Ventilation—The vents and other openings in the cabinet are designed for

ventilation. Do not cover or block these vents and openings since insufficient

ventilation can cause overheating and/or shorten the life of the product. Do not

place the product on a bed, sofa, rug or other similar surface, since they can

block ventilation openings. This product is not designed for built-in installation; do

not place the product in an enclosed place such as a bookcase or rack, unless

proper ventilation is provided or the manufacturer’s instructions are followed.

■ The Liquid Crystal panel used in this product is made of glass. Therefore, it can

break when the product is dropped or applied with impact. Be careful not to be

injured by broken glass pieces in case the Liquid Crystal panel breaks.

■ Heat sources—Keep the product away from heat sources such as radiators,

heaters, stoves and other heat-generating products (including amplifiers).

6

IMPORTANT SAFETY PRECAUTIONS (Continued)

■ If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to

provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical

Code provides information with respect to proper grounding of the mast and supporting structure, grounding of the

lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection

to grounding electrodes, and requirements for the grounding electrode.

■ Power Lines – An outside antenna system should not be located in the vicinity of

overhead power lines or other electric light or power circuits, or where it can fall

into such power lines or circuits. When installing an outside antenna system,

extreme care should be taken to keep from touching such power lines or circuits

as contact with them might be fatal.

ANTENNA

LEAD IN

WIRE

ANTENNA

DISCHARGE UNIT

(NEC SECTION 810-20)

GROUNDING CONDUCTORS

(NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART 250, PART H)

ELECTRIC

SERVICE

EQUIPMENT

NEC—NATIONAL ELECTRICAL CODE

GROUND

CLAMP

EXAMPLE OF ANTENNA GROUNDING AS PER

NATIONAL ELECTRICAL CODE

■ Lighting – For added protection for this television equipment during a lightning

storm, or when it is left unattended and unused for long period of time, unplug it

from the wall outlet and disconnect the antenna. This will prevent damage to the

equipment due to lightning and power-line surges.

■ To prevent fire, never place any type of candle or naked flames on the top or

near the TV set.

■ To prevent fire or shock hazard, do not expose this products to dripping or

splashing. No objects filled with liquids, such as vases, should be placed on the

products.

ENGLISH

7

REGARDING BATTERY CARE

• Charge the battery only at temperatures within the range of

50°F to 86°F (10°C to 30°C) (temperatures that are comfort-

able for people). At lower temperatures it becomes more

difficult to charge the battery and the battery deteriorates. It is

not possible to sufficiently charge the battery at high tempera-

tures.

• The battery may become hot during charging or during use,

but this is not a sign of malfunctioning.

• It may take more time to fully charge a hot battery.

Precautions to be Taken during Charging

Regarding Operating Time and Use under Low Temperatures for the Battery

• The battery has a certain life expectancy. The battery is

consumed as time elapses even if the battery is not used. A

battery that has been used for about a year may give you less

operating time depending on the conditions under which it

was stored. If a battery that has been charged correctly

operates for a much shorter time than usual, it has reached

the end of its life and must be replaced with a new battery.

• When the battery is at a low temperature (lower than 50°F

(10°C)) in winter, the operating time may be very short. The

battery undergoes an internal chemical reaction in order to

generate electricity. When the temperature outside is lower,

the chemical reaction becomes less vigorous and operating

time becomes shorter.

How to Get the Most out of the Battery

• Turn off the power supply frequently when not in use in order to give the battery longer life.

• The battery is consumed as time elapses even if the battery is

not used. To prevent consumption;

(1) If the battery will not be used for a long time, use the

product to run down what is left of the battery charge and

set “Battery charge” to “off” in the menu screen. (Refer to

page 28.)

(2) Make sure to use the battery at least once every six

months.

Storage Precautions

Charge the battery before use.

Battery type lithium-ion battery

Nominal voltage 11.1 V

Battery capacity 5700 mAh

Operating temperature 50°F to 86°F (10°C to 30°C)

Maximum dimensions appx. Length 8

23

/64 inch (212 mm) × Width 1

5

/8 inch (41 mm) × Height 1

35

/64 inch (39 mm)

Weight appx. 1.1 lbs. (0.5 kg)

• The battery used in the product is a lithium-ion battery. Even if

the battery is charged and stored, the amount of charge in the

battery will drop.

• Make sure to charge the battery until the charge indicator of

the product goes off (fully charged). The operating time is

shortened when using a battery which has not been fully

charged. (For a detailed description of how to charge the

battery, refer to page 20.)

Battery Specification

8

REGARDING BATTERY CARE (Continued)

Prohibited use for which safety is not guaranteed.

• Do not try to disassemble or modify the battery. The battery

contains safety mechanisms and protection devices.

Damaging these safety devices may cause the battery to

generate heat or smoke, or to rupture or ignite.

• Do not connect the + and – terminals together with metal

such as wires. Do not carry or store the battery together

with metal objects such as necklaces and hairpins. Doing

so may cause the battery to be short-circuited so as to

cause an extremely large amount of electric current to flow,

which may cause the battery to generate heat or smoke,

rupture or ignite, or may cause metal objects such as wire,

necklaces, or hairpins to heat up.

• Do not expose batteries to fire or heat. Doing so may cause

insulating materials to melt, damage gas exhaust valves or

safety mechanisms, or ignite electrolytic solutions, which

may cause the battery to generate heat or smoke, rupture

or ignite.

• Do not leave the battery in or near fire, stoves, or other

high-temperature locations (of temperatures greater than

140°F (60°C)). If a resin separator is damaged by heat, the

battery may become internally short-circuited and this may

cause the battery to generate heat or smoke, rupture or

ignite.

• Do not expose the battery to water or salt water, or allow

the battery to get wet. If the protection device contained in

the battery is broken, this may cause the battery to gener-

ate heat or smoke, rupture or ignite.

• Do not charge the battery near a fire or in direct sunlight. If

the battery becomes hot, the protection device for prevent-

ing danger operates to disable the battery from being

charged. If the protection device contained in the battery

becomes broken, the battery is charged at an abnormal

electric current or voltage. An abnormal chemical reaction

occurs inside the battery which may cause the battery to

generate heat or smoke, rupture or ignite.

• Charge the battery in compliance with the specified charg-

ing conditions. If the battery is charged without compliance

to the charging conditions (at temperatures greater than the

specified temperature, at voltages and electric current

greater than the specified amount or with modified charg-

ers), the battery may be overcharged or charged at an

abnormal electric current and an abnormal chemical

reaction may occur inside the battery, which may cause the

battery to generate heat or smoke, rupture or ignite.

• Do not pierce the battery with nails, strike the battery with a

hammer, or step on the battery. Doing so may cause the

battery to generate heat or smoke, rupture or ignite.

• Do not subject the battery to strong impacts or throw it

away. If the protection device contained in the battery

becomes broken, the battery is charged at an abnormal

electric current or voltage. An abnormal chemical reaction

may then occur inside the battery, which may cause the

battery to generate heat or smoke, rupture or ignite.

• Do not use the battery if it has been considerably damaged

or deformed. This may cause the battery to generate heat

or smoke, rupture or ignite.

• Do not solder directly onto the battery. Doing so may cause

insulating materials to melt, or damage gas exhaust valves

or the safety mechanism, which may cause the battery to

generate heat or smoke, rupture or ignite.

• Use a battery case when carrying the battery.

• Keep the battery out of reach of children.

• In the event that the fluid inside the battery gets into one’s

eye, do not rub the eye because this may cause loss of

eyesight. Rinse the eye with clean water and consult a

doctor immediately. In the event that the fluid becomes

attached to skin or clothes, wash it off with clean water

immediately as this may cause injury.

ENGLISH

9

CORRECT USE OF THE PRODUCT

Precautions Regarding Radio Waves

■ Do not use the product at the following locations. There may be cases where noise occurs or transmission/reception is

not possible.

• Locations where magnetic fields, electrostatic or interference occurs due to devices such as Bluetooth, wireless LANs, or

microwave ovens etc. that utilize the same frequency band (2.4 GHz) as the product. (There may be cases where radio waves

cannot reach depending on the environment.)

• Keep the product away from a radio devices during use. (There may be cases of noise interference.)

■ Under the same frequency band as the product uses, in addition to Bluetooth, wireless LANs, and microwave ovens

etc. that utilize the same frequency band (2.4 GHz) as the product, operation can also take place at on-site radio

stations that require a license for mobile object identification used in factories and manufacturing lines etc. and

specified low power radio stations.

• Before using the product, make sure that there is no on-site radio stations for mobile object identification or specified low power

radio stations operating in the vicinity of the product.

• If there is any interference occurring to on-site radio stations for mobile object identification due to the product, stop using the

product immediately.

Regarding Range of Usage

■ The product is limited to domestic use.

(There is a possibility that transmission distance may become short depending on the communication environment.)

■ In the following cases, reception may become bad or impossible, which may cause sound and pictures to be inter-

rupted (pictures and sound are stopped), or blocks of noise to appear.

• Using the product in a reinforced concrete building such as a condominium building or a house of a metal structure.

• Using the product at locations near large-scale metallic furniture.

• Using the product in a crowd of people or close to buildings or obstacles, etc.

• Using the product at locations where magnetic fields, electrostatic and interference occur due to devices such as Bluetooth,

wireless LANs, or microwave ovens, etc. that utilize the same frequency band (2.4 GHz) as the product.

■ Regarding reflected radio waves

• Radio waves that reach a television receiver are radio waves (direct waves) directly transmitted from a transmitter and radio

waves (reflected waves) arriving from various directions as a result of being reflected by walls, furniture, or buildings etc. There

are good and bad positions in terms of wave conditions due to the influence of these reflected waves, which may cause poor

picture reception. In this case, try changing the location of the TV receiver slightly. There are cases where pictures and sound

are distorted or interrupted due to the reflected waves as a result of a person passing over or approaching between the transmit-

ter and the television receiver.

When a signal other than a regular signal is input

• When a signal other than a regular signal that is incompatible with this unit is input, the screen may freeze, but this is not a

malfunction.

• When a signal other than a regular signal is input from the Antenna, AV-IN1, AV-IN2, or AV-IN3 terminals, reception may be bad

depending on the performance of the Wireless Center, and the message “THIS SIGNAL IS NOT COMPATIBLE” will display.

• Signals compatible with the Wireless Center are as follows:

H: 15.625 kHz / V: 50.0 Hz, 59.52 Hz

H: 15.73426 kHz / V: 59.94 Hz

(Note: Reception may be available with AV-IN4.)

Precaution Regarding Electromagnetic Wave Disturbance

• If electric devices, such as a cellular phone, are used near this unit, electromagnetic wave disturbance may occur between

apparatus. In such cases, the picture quality may decrease and noise may appear.

10

SUPPLIED ACCESSORIES

Confirm that the following accessories are provided with the product.

Wireless remote control (×1), Remote control holder (×1),

“AAA” size (UM/SUM-4) dry batteries (×2)

Wireless Center (×1), Wireless Center stand (×1)

Battery (×1)

AC adapters (×2)

Cable clamps (×2), Table stand (×1)

*Product shape varies in some countries.

Screws (×3)

(See pages 11, 15, 18) (See page 19)

(See pages 13, 21)

(See page 17)

(See page 59)

(See pages 55, 57, 60)

Terminal cover

SIGNAL LEVEL

MAIN

POWER

LIQUID CRYSTAL TELEVISION

TÉLÉVISEUR ACL

TELEVISOR CON PANTALLA

DE CRISTAL LÍQUIDO

TELEVISOR DE CRISTAL

LÍQUIDO

LC-15L1U

OPERATION MANUAL

MODE D’EMPLOI

MANUAL DE OPERACIÓN

MANUAL DE OPERAÇÃO

ENGLISHFRANÇAISESPAÑOLPORTUGUÊS

Manuals

Video controller (×1)

(See page 12)

Antenna cables (×2)

RRMCGA152WJSA

LHLDZA216WJZZ

UBAT1A011WJZZ

GDAI-A074WJSA

TINS-B124WJZZ

QCNWGA033WJPZ

QCNWG0003CEPA

Connecting System Chart of

LC-15L1U

TCAUZA072WJZZ

Registration Card

TCAUDEA028WJZZ

Caution Sheet

TCAUZA071WJZZ

LHLDW0109CESA

(See page 15) CDAI-A072WJ02

QACCDA023WJPA × 2 pcs

UADP-A042WJPZ

UADP-A041WJPZ

QCNWG0004CEZZ

ENGLISH

11

PREPARATION

Using the Remote Control

■ Use the remote control by pointing it toward the remote control sensor window

on the main unit. Objects between the remote control and sensor window may

prevent proper operation.

Cautions regarding use of the remote control

■ Do not expose the remote control to shock.

In addition, do not expose the remote control to liquid, and do not place it in an

area with high humidity.

■ Do not install or place the remote control under direct sunlight. The heat may

cause deformation of the unit.

■ The remote control may not work properly if the remote control sensor window

of the main unit is under direct sunlight or strong lighting. In such cases,

change the angle of the lighting or LCD TV set, or operate the remote control

closer to the remote control sensor window.

Batteries for the Remote Control

Before using the LCD TV set for the first time, install two (“AAA” size, UM/SUM-4) batteries (supplied). When the batter-

ies become depleted and the remote control fails to operate, replace the batteries with new (“AAA” size, UM/SUM-4)

batteries.

1

Open the battery cover.

■ Slide the cover while pressing the

(b) part.

2

Insert two (“AAA” size, UM/SUM-

4) batteries.

+

–

+

–

■ Position the positive and negative

ends of the batteries as indicated in

the compartment.

Caution!

Cautions regarding batteries

Improper use of batteries can result in chemical leakage and/or explosion. Be sure to follow the instructions below.

• Place batteries with their terminals corresponding to the (+) and (–) as indicated in the compartment.

• Different types of batteries have different characteristics. Do not mix batteries of different types.

• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new battery and/or cause the old

battery to leak chemicals.

• Remove batteries when they become weak.

Chemicals that leak from batteries can cause a rash. If chemical leakage is found, wipe with a cloth.

• The batteries supplied with the product may have a shorter life expectancy due to storage conditions.

• If the remote control will not be used for an extended period of time, remove the batteries from the remote control.

SLEEP indicator

CHARGE indicator

POWER indicator

Remote sensor window

CHARGE SLEEPPOWER

3

Close the battery cover.

■ Engage the claw on the cover into

the battery housing and slide shut.

12

F-type connector

75-ohm coaxial cable

Antenna Connection

PREPARATION (Continued)

OUTDOOR ANTENNA CONNECTION

• Use one of the following two diagrams if you connect an outdoor antenna.

A: Using a VHF/UHF combination outdoor antenna

B: Using separate VHF and/or UHF outdoor antennas

• Connect the outdoor antenna cable lead-in to ANT. (Antenna terminal) on the rear of the Wireless Center.

F-type connector

75-ohm coaxial cable (round)

300-ohm twin-lead cable (flat)

1. A 75-ohm system is generally a round cable with F-type connector that can easily be

attached to a terminal without tools (not supplied).

2. A 300-ohm system is a flat “twin-lead” cable that can be attached to a 75-ohm terminal

through a 300-75-ohm adapter (not supplied).

ANTENNAS

• The antenna requirements for good color television reception are more important than those for black & white television reception.

For this reason, a good quality outdoor antenna is strongly recommended.

The following is a brief explanation of the type of connections that are provided with the various antenna systems.

NOTICE

F-type connector should be finger-tightened only.

When conecting the RF cable to the TV set, do not tighten F-type

connector with tools.

If tools are used, it may cause damage to your TV set.

(The breaking of internal circuit, etc.)

Wireless Center

IN

OUT

AV-IN1AV-IN1AV-IN3

IR

OUT

POWER

INPUT

DC12V

FACTORY

SERVICE

S-VIDEO

MONITOR

OUT

MONITOR

OUT

VIDEO

AUDIO

L

AUDIO

R

AV-IN2

/OUT

ANT.

TV/VCR/DVD, etc.

TV

VCR

DVD

75-ohm

coaxial cable

Antenna cable

300-ohm

twin-lead

VHF/UHF

antenna

VHF/UHF

antenna

300/75-ohm

adapter

(not supplied)

300-ohm

twin-lead

300-ohm

twin-lead

75-ohm

coaxial cable

OUTIN

VHF

antenna

UHF

antenna

Combiner

(not supplied)

or

B: Separate VHF and/or UHF antennas

A: Combination VHF/UHF antenna

ENGLISH

13

Antenna Connection (Continued)

PREPARATION (Continued)

Cable TV converter/

descrambler

(not supplied)

Two-set

signal

splitter

(not

supplied)

Cable TV line

RF switch (not supplied)

OUT

IN

• A 75-ohm coaxial cable connector is built into the set for easy hookup. When connecting the 75-ohm coaxial cable to the

set, screw the 75-ohm cable to the ANT. terminal.

• Some cable TV companies offer “premium pay channels”. Since the signals of these premium pay channels are scram-

bled, a cable TV converter/descrambler is generally provided to the subscriber by the cable TV company. This converter/

descrambler is necessary for normal viewing of the scrambled channels. (Set your TV to channel 3 or 4, typically one of

these channels is used. If this is unknown, consult your cable TV company.) For more specific instructions on installing

cable TV, consult your cable TV company. One possible method of utilizing the converter/descrambler provided by your

cable TV company is explained below.

Please note: An RF switch provided with two inputs (A and B) is required (not supplied).

“A” position on the RF switch (not supplied): You can view all unscrambled channels by using the TV’s channel keys.

“B” position on the RF switch (not supplied): You can view the scrambled channels via the converter/descrambler by using

the converter’s channel keys.

CABLE TV (CATV) CONNECTION

Note:

• Consult your SHARP Dealer or Service Center for the type of splitter, RF switch or combiner that might be required.

Power Connection

Connect to the DC input terminal of each product.

Note:

• Always turn the MAIN POWER button of the LCD TV set and the power button of the Wireless Center to OFF when connecting the AC

adapters.

• If there is a Sharp product close to the video controller, the product may malfunction during transmission of the video controller.

• Unplug the AC adapters from the LCD TV set, Wireless Center unit and AC wall outlet when the LCD TV set is not to be used for a

long period of time.

AC wall

outlet

AC adapter

AC cord

TV main unit

AC wall

outlet

AC adapter

AC cord

IR

OUT

POWER

INPUT

DC12V

FACTORY

SETTING

Wireless

Center

14

MAIN UNIT PART NAMES

Numbers in indicate the main pages where the corresponding item is described in this manual.

CHARGE indicator

POWER indicator

Remote sensor windowTable stand (Detachable)

Left speaker

Right speaker

15

SLEEP indicator

36

20

22

11

Main unit (Top view: Control section)

Main unit (Front view)

CHVOL MENU TV/VIDEO MAIN POWER

-

+

VOL (–)/(+)

CH ( )/( )

MAIN POWER

TV/VIDEO

MENU

33

34

35

32

31

ENGLISH

15

MAIN UNIT PART NAMES (Continued)

Main unit (Rear view)

AUDIO

AV- IN4

VIDEO

S-VIDEO

HEAD

PHONE

FACTORY

SERVICE

L

R

CHCH

ENTER

P

O

WE

R

DISPLAY

SLEEP PIC. FLIP

MUTE

VOL

BRIGHT TV/VIDEO MENU

FLASH

BACK

MTS

POWER INPUT DC 15 V

HEADPHONE jack

S-VIDEO

VIDEO

AV-IN4

AUDIO(R)

AUDIO(L)

Remote control holder

The remote control can be placed in the

remote control holder when moving the TV.

1 Attach the remote control holder to the

handle with the arrow ( ) in the center of

the holder facing upward.

2 Place the remote control in the remote

control holder.

Table stand

release button

Handle

1

2

CHCH

ENTER

POWER

DISPLAY

SLEEP PIC. FLIP

MUTE

VOL

BRIGHT TV/VIDEO MENU

FLASH

BACK

MTS

Removing and Attaching the Table Stand

1

Lift the main unit straight up by holding the handle while depressing the table

stand release button.

2

Unfold the stand.

• Securely unfold the stand until you hear a clicking sound. Only use the

stand after first unfolding until a clicking sound is heard to ensure that it is

stable.

3

Fold up the stand.

• Return the stand to its original unfolded position.

4

Insert the main unit straight into the table stand.

• The main unit cannot be inserted if inclined on an angle. Inserting the main

unit with force can cause damage or a malfunction.

Stand

Handle

Table stand

release button

Table stand

16

MAIN UNIT PART NAMES (Continued)

Removing the Back Cover

■ Before connecting cables and cords to the rear terminals, remove the back covers. Push

in the tabs and pull out the back covers carefully.

■ To mount the cover, insert the 2 hooks on the bottom of the cover into the cabinet and

press on the upper part of the back cover until the tab locks in place with a click.

Listening with Headphones

■ Plug the headphone mini-plug into the HEADPHONE jack located on the rear of the TV set.

Note:

• Headphones are not included in the supplied accessories.

• No sound is heard from the main unit speakers when a headphone mini-plug is connected into the HEADPHONE jack.

▼ On-screen display

Adjust the sound volume

using VOL (e)/(f) on the

remote control.

Headphones

AUDIO

AV- IN4

VIDEO

S-VIDEO

L

R

HEAD

PHONE

Rear terminal

20

VOLUME

ENGLISH

17

WIRELESS CENTER PART NAMES

SIGNAL LEVEL

MAIN

POWER

IN

OUT

AV-IN1AV-IN1AV-IN3

IR

OUT

POWER

INPUT

DC12V

FACTORY

SERVICE

S-VIDEO

MONITOR

OUT

MONITOR

OUT

VIDEO

AUDIO

L

AUDIO

R

AV-IN2

/OUT

ANT.

Transmission

SIGNAL LEVEL

indicator

(Reception gain)

· Green:

Communication

in progress

· Red:

Difficulty

in transmission

· Not lit:

Not communicating

POWER indicator

· Green:

Operation in

progress

(when power is on)

· Red: Standby

MAIN

POWER

button

Front

Antenna

input

terminal

Antenna

output

terminal

Rear

VIDEO

AUDIO (L)

AUDIO (R)

AV-IN1 (S-VIDEO)

MONITOR

OUT

MONITOR OUT

(S-VIDEO)

Factory

adjustment

terminal

POWER INPUT

DC 12V

Video control

terminal

VIDEO

AUDIO (L)

AUDIO (R)

AV-IN1

VIDEO

AUDIO (L)

AUDIO (R)

AV-IN3

VIDEO

AUDIO (L)

AUDIO (R)

AV-IN2

/OUT

Wireless Center

TV main unit

Wireless Center

stand

Rubber foot

POWER Indicator

When the TV is turned off with the remote control, the

Wireless Center is switched to standby (POWER indicator

is lit red). (There may be a time lag of about 5 to 6

seconds.)

Placing the Wireless Center Where You Want It

We recommend placing the Wireless Center in an area

where there are no obstructions to impede radio wave

transmission/reception.

(Do not place the Wireless Center in a box.)

Note:

• The distance for which transmission is possible between the

main unit and Wireless Center is about 15 metres. However,

this distance may vary depending on the location or

conditions under which the Wireless Center is used.

• If the main unit gets close to the Wireless Center, there may

be cases where noise appears on the screen. In this case,

keep the main unit away from the Wireless Center until the

noise decreases, or try to change the transmission channel

setting (page 28).

Setting up the Wireless Center

• The Wireless Center can be placed horizontally or upright.

• When placing horizontally:

The side on which the rubber feet are attached is the

bottom.

• When placing upright:

Fasten the stand to the bottom of the Wireless Center with

the screws provided.

* Failure to securely fasten the stand may cause the

Wireless Center to tip over during use.

18

REMOTE CONTROL

CHVOL

POWER

ENTER

DISPLAY

MUTE

SLEEP PIC. FLIP

BRIGHT TV/VIDEO MENU

FLASH-

BACK

1 POWER (p. 22)

Switch the Liquid Crystal Television power on or off.

2 DISPLAY

Display the channel and time information.

3 SLEEP (p. 36)

Set the sleep timer.

4 ENTER

Execute a command.

5 BRIGHT (p. 37)

Adjust the brightness of the screen.

6 MUTE (p. 33)

Mute the sound.

7 VOL (+)/(–) (p. 33)

Set the volume.

8 CH ( )/( ) (p. 34)

Select channel.

9 MTS (p. 33)

Select audio settings.

10 PIC. FLIP (p. 38)

Set the orientation of the picture.

11 a/b/c/d (Cursor control) (p. 22)

Select a desired item on the screen.

12 TV/VIDEO (p. 32)

Select a Liquid Crystal Television input source.

13 MENU (p. 35)

Display the menu screen.

14 FLASHBACK (p. 34)

Return to the previous channel.

15 Channel Select (p. 34)

Set the channel.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

ENGLISH

19

POWER

Turning the Main Power on and off

See page 15 for how to remove the table stand.

■ Installing the Battery

1

Open the cover of the battery

case.

2

Remove the terminal cover of the

battery.

3

Pack toward the left side first and

then push the battery inside the

compartment.

4

Shift the battery to the right.

• The lever will return to its

original position.

• Move the battery to the right

until the lever returns

completely.

5

Close the cover of the battery

case.

• Align the tabs of the cover with

the corresponding grooves in

the TV and snap into position.

■ When Removing

With the lever pulled forward, lift up on

the battery while pushing to the left.

• Always make sure to attach the

terminal cover to the removed

battery.

Place on a soft cloth.

Cover of the

battery case

Terminal cover

Battery

Lever

Page is loading ...

Sharp LC-15L1U-S Operation Manual User manual

This manual is also suitable for

Sharp LC-15L1U-S Operation Manual User manual

Related papers

Other documents