Fujitsu Computer Accessories User manual

Fujitsu
Brand
Fujitsu
Model
Computer Accessories
Type
User manual

This manual is also suitable for

Fujitsu Computer Accessories is a powerful tool that can help you diagnose and repair problems with your ATA/IDE hard disk drive. It can perform a variety of tests, including a Quick Test and a Comprehensive Test. The Quick Test checks the drive's SMART status, performs a buffer write/read test, and scans the media for errors in the outer and inner areas. The Comprehensive Test performs a media scan of all areas of the drive. After performing the tests, the program will log all the drive information on SA-4, Head 0, Sector 0. If a test fails, the FJDT utility will report the result in the form of a status code. You can then contact Storage Products Group Technical Assistance Center (SPG TAC) to have the code result explained.

Fujitsu Computer Accessories is a powerful tool that can help you diagnose and repair problems with your ATA/IDE hard disk drive. It can perform a variety of tests, including a Quick Test and a Comprehensive Test. The Quick Test checks the drive's SMART status, performs a buffer write/read test, and scans the media for errors in the outer and inner areas. The Comprehensive Test performs a media scan of all areas of the drive. After performing the tests, the program will log all the drive information on SA-4, Head 0, Sector 0. If a test fails, the FJDT utility will report the result in the form of a status code. You can then contact Storage Products Group Technical Assistance Center (SPG TAC) to have the code result explained.

FCPA SPG TAC LAB
FUJITSU DIAGNOSTIC TOOL MANUAL (ATA/IDE)
Version 4.0 – 6.2
This document explains the usage of the Fujitsu Diagnostic Tool for ATA/IDE Hard Disk Drives.
Disclaimer
The Fujitsu Diagnostic Tool (FJDT) is provided "as is" without any warranty of any kind, either
expressed or implied, including, but not limited to, the implied warranties of merchantability and
fitness for a particular purpose. The entire risk as to the quality and performance of the program
is with you. In no event will FUJITSU or any of its subsidiaries be liable to you for any damages,
including any general, special, incidental or consequential damages arising out of the use or
inability to use this program (including but not limited to any loss of profit or savings, loss of data
or a failure of the program to operate with any other programs), even if FUJITSU or any of its
subsidiaries has been advised of the possibility of such damages.
Table of contents
Disclaimer...........................................................................................................................................1
Table of contents.................................................................................................................................1
1. User’s Guide ...................................................................................................................................1
2. Test Sequences and Schedules ........................................................................................................1
3. Test Results .....................................................................................................................................2
4. Contact Info ....................................................................................................................................2
1. User’s Guide
Requirements
• Operating System: DOS (This version has only been tested from DOS 5.0 above)
• CPU: IBM-PC compatibles -> 80x86 CPU - Based motherboards
Running the program (You cannot run this program under a WINDOWS environment)
• Boot from a clean DOS disk (Windows 98 boot floppy or DOS boot floppy).
• Change to the drive/directory where FJDT.EXE is located.
• Syntax: A:>FJDT
2. Test Sequences and Schedules
FJDT runs the test sequence on the attached or a selected ATA/IDE device.
Note: The Comprehensive Test is performed only when the drive passes the initial Quick Test.
Quick Test
• Pre-SMART Check
• Buffer Write/Read Test
• Media Scan for Outer Area (LBAs of first 150MB)
• Media Scan for Inner Area (LBAs of last 50MB)
• Fundamental Seek Test (Random Seek and Random Read)
• Post-SMART Check
Fujitsu Proprietary and Confidential | Page 1 of 2
FCPA SPG TAC LAB
Comprehensive Test
• Media Scan of All Areas
• Post-SMART Check
3. Test Results
After performing tests, the program will log all the drive information on SA-4, Head 0, Sector 0.
When a test has completed then the FJDT utility will report the result in the form of a status code
such as "A101H4". Please contact Storage Products Group Technical Assistance Center (SPG
TAC) to have the code result explained.
4. Contact Info
For technical support, you may contact Storage Products Group Technical Assistance Center
(SPG TAC) at spgtac@fcpa.fujitsu.com or call 1-888-664-0672, option 1 or use our chat system at
http://www.fcpa.com/support/hard-drives/contact.html.
Fujitsu Proprietary and Confidential | Page 2 of 2
  • Page 1 1
  • Page 2 2

Fujitsu Computer Accessories User manual

Fujitsu
Brand
Fujitsu
Model
Computer Accessories
Type
User manual
This manual is also suitable for

Fujitsu Computer Accessories is a powerful tool that can help you diagnose and repair problems with your ATA/IDE hard disk drive. It can perform a variety of tests, including a Quick Test and a Comprehensive Test. The Quick Test checks the drive's SMART status, performs a buffer write/read test, and scans the media for errors in the outer and inner areas. The Comprehensive Test performs a media scan of all areas of the drive. After performing the tests, the program will log all the drive information on SA-4, Head 0, Sector 0. If a test fails, the FJDT utility will report the result in the form of a status code. You can then contact Storage Products Group Technical Assistance Center (SPG TAC) to have the code result explained.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents