RCA DRC6389T User manual

RCA
Brand
RCA
Model
DRC6389T
Category
DVD players
Type
User manual
DRC6389t
8" Dual Screen Mobile DVD
OWNER'S MANUAL
GB - 1
SAFETY PRECAUTIONS
* SEE BOTTOM OF UNIT FOR GRAPHIC
SYMBOLS *
The lightning flash with an arrowhead
symbol, within the equilateral triangle, is
intended to alert the user to the presence
of uninsulated "dangerous voltage" within
the product's enclosure that may be of
sufficient magnitude to cause an electric
shock.
The exclamation point within the
equilateral triangle is intended to alert
the user to the presence of important
operating and maintenance (servicing)
instructions in this owner's manual.
CAUTION
INVISIBLE LASER RADIATION WHEN
OPEN AND INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM.
DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-
SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO PREVENT FIRE OR
SHOCK HAZARD, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
DO NOT PLACE OBJECTS FILLED WITH
LIQUIDS ON OR NEAR THIS UNIT.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS
OR PERFORMANCE OF PROCEDURES OTHER THAN
THOSE SPECIFIED MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
CAUTION: DANGER OF EXPLOSION IF BATTERY IS
INCORRECTLY REPLACED. REPLACE ONLY WITH
THE SAME OR EQUIVALENT TYPE.
On Placement
• Donotusethis unit in places that areextremely
hot, cold, dusty or humid.
• Donotrestricttheairowofthisunitbyplacingit
somewhere with poor air flow, by covering it with a
cloth, or by placing it on bedding or carpeting.
• This unit should not be exposed to dripping or
splashing liquid and no objects filled with liquids,
such as vases, should be placed on the unit.
FCC Information
WARNING: Changes or modifications to this unit
not expressly approved by the party responsible for
compliance could void the user authority to operate
the equipment.
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. This equipment, used in accordance with
the instructions, may cause harmful interference to
radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this equipment
does cause harmful interference to radio or television
reception, which can be determined by turning the
equipment off and on, the user is encouraged to
try to correct the interference by one or more of the
following measures:
• Reorientorrelocatethereceivingantenna.
• Increase the separation between the equipment
and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV
technician for help.
Shielded cables must be used with this unit to ensure
compliance with the Class FCC limits.
On Safety
• WhenconnectingordisconnectingtheACpower
cord, grip the plug and not the cord itself. Pulling
the cord may damage it and create a hazard.
• Whenyouarenotgoingtousetheunitforalong
time, disconnect the power adapter.
On Condensation
• Whenleftinaheatedroomwhereitiswarmand
damp, water droplets or condensation may form
inside the unit. When there is condensation inside
the unit, the unit may not function normally. Let the
unit stand for 1 to 2 hours before turning the power
on, or gradually heat the room and let the unit dry
before use.
Rating Plate Location
• Theratingplatelocationisontherearoftheunit.
This product contains a low
power laser device.
GB - 2
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding - type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide
blade or the third prong is provided for your safety. If the provided plug does not fit into your wall outlet,
consult an electrician for replacement of the obsolete outlet.
10.Protect the AC power cord from being walked on or pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11.Only use attachments/accessories
by the manufacturer.
12.Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury
from tip-over.
13.Unplug this apparatus during lightning storms or when unused for long periods of time.
14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as the power-supply cord or plug is damaged, liquid has spilled or objects have
fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped.
• TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR
MOISTURE. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR NEAR THIS UNIT.
• SHOULD ANY TROUBLE OCCUR, DISCONNECT THE AC POWER ADAPTER AND REFER
SERVICING TO A QUALIFIED TECHNICIAN.
•
SAFETY PRECAUTIONS
TO BE COMPLETELY DISCONNECT THE POWER INPUT, THE AC/DC ADAPTOR OF APPARATUS
SHALL BE DISCONNECTED FROM THE MAINS THE AC/DC ADAPTOR OF APPARATUS SHOULD NOT
BE OBSTRUCTED OR SHOULD BE EASILY ACCESSED DURING INTENDED USED.
GB - 3
TABLE OF CONTENTS
Safety Precautions ............................................1
Important Safety Instructions ..............................2
Table of Contents ................................................3
Disc Formats ......................................................4
Accessories .......................................................5
Remote Control .................................................5
Control Reference Guide ................................ 6-8
Remote Control........................................................6
DVD Player ..............................................................7
Monitor ..................................................................... 8
Power Supply ................................................ 9-11
Using the Car Power Adaptor ..................................9
Using the AC Power Adaptor .................................10
Using the Built-in Battery .......................................11
Connections .................................................12-14
Watching a DVD on the Main Unit and the
Monitor ................................................................... 12
Connecting a TV ....................................................12
Connecting a Stereo Receiver or Amplifier ............13
Connecting Game Systems/Video Equipment .......13
Using the Monitor with Other Equipment while
Playing DVD on the Main Unit................................14
Connecting to a Video Equipment ......................... 13
Using Headphones/Earphones .............................. 14
Mounting in the Vehicle .....................................15
Using the Stand for Desktop Use .....................16
Sound System ..................................................16
Unit Operation .................................................16
Playing a Disc ..............................................17-18
Playing a Disc ........................................................ 17
Pausing Playback (Still Mode) ...............................17
Stopping Playback .................................................17
Fast Forward / Fast Reverse .................................. 17
Skip (Forward / Reverse) .......................................17
Audio Selection ..................................................... 17
Subtitle Selection ................................................... 18
Angle Selection ...................................................... 18
Display Function ....................................................18
Adjust the LCD Screen ..........................................18
Locating a Desired Section ...............................19
Locating a Specific Title ......................................... 19
Locating a Specific Chapter ................................... 19
Locating a Specific Time ........................................ 19
DVD Programmable memory ............................20
Playing Titles/Chapters in a Favourite Order .........20
Repeat playback ...............................................20
Repeating a Chapter/Title ..................................... 20
Repeating a Single Track/Whole Disc ................... 20
Repeating a Specific Section ................................ 20
Viewing JPG Files ............................................21
Play Modes for CD or JPG Disc .......................21
Customizing the Function Settings ..............22-23
Language Setup ....................................................22
Video Setup ...........................................................23
Misc Setup ............................................................. 24
Maintenance .....................................................24
Cleaning the Disc...................................................24
Cleaning the Unit ...................................................24
Important Note ......................................................
24
Troubleshooting Guide ......................................25
GB - 4
DISC FORMATS
The unit can playback discs bearing any of the following marks:
Region Management Information
Region Management Information: This unit is designed and manufactured to respond to the Region
Management Information that is encoded on DVDs. If the region number printed on the DVD does not
correspond to the region number of this unit, this unit cannot play that disc.
The region number of this unit is 1.
Disc Function or Operation that is Not Available
When the symbol appears on the TV screen, it indicates that the function or operation attempted is not
available at that time. This occurs because the DVD manufacturer determines the specific functions. Certain
functions may not be available on some discs. Be sure to read the documentation provided with the disc.
Titles, Chapters and Tracks
• DVDs are divided into “titles” and “chapters”. If the
disc has more than one movie on it, each movie
would be a separate “title”. “Chapters” are sections
of titles.
• Audio CDs are divided into “tracks”. A “track” is
usually one song on an Audio CD.
Note:
• Numbers identify each title, chapter, and track on a disc. Most discs have these numbers recorded on
them, but some do not.
Icons Used on DVDs
Sample lcons
Note:
• When playing back a CD-G (Graphics) or CD EXTRA disc, the audio portion will be played, but the graphic
images will not be shown.
Notes on Unauthorized Discs
You may not be able to play back some DVDs on this unit if they were purchased from outside your geographic
area or made for business purposes.
DVDs
[8cm(3")/12cm(5") disc]
Audio CDs
[8cm(3")12cm(5") disc]
Compatible
Language selections for audio
Language selections for subtitles
Screen aspect ratio
Multiple camera angles
Region code indicator
Title 1
Chapter 1
Title 2
Chapter 2 Chapter 3 Chapter 1 Chapter 2
Track 1 Track 2 Track 3 Track 4 Track 5
GB - 5
ACCESSORIES
REMOTE CONTROL
Using the Remote Control
• PointtheremotecontrolattheREMOTESENSOR
located on the unit.
• When there is a strong ambient light source, the
perform ance of the infrared REMOTE SENSOR
may be degraded, causing unreliable operation.
• The recommended effective distance for remote
operation is about 16 feet (5 meters).
To Change Remote Battery
1. Open the battery door.
Take out the plastic sheet before operating the
Remote Control.
2. Insert one CR2025 (3V) size battery.
Remote Control (with battery) ..........................................................................................................x 1
Car Power Adapter ...........................................................................................................................x 1
AC Power Adapter ............................................................................................................................x 1
DC-AV Cable ....................................................................................................................................x 1
Mounting Strap .................................................................................................................................x 2
Please check and identify the supplied accessories.
BATTERY REPLACEMENT
When battery becomes weak, the operating distance of the remote control will be greatly reduced and you
will need to replace the battery.
Note:
• Iftheremotecontrolisnotgoingtobeusedforalongtime,removethebatterytoavoiddamagecausedby
battery leakage corrosion.
• Whendiscardingbatteries,environmentalproblemsmustbeconsideredandlocalrulesorlawsgoverning
the disposal of these batteries must be strictly followed.
WARNING:
• Donotdisposeofbatteryinre,batterymayexplodeorleak.
• Thebatteryshouldnotbeexposedtoexcessiveheatsuchassunshine,reorthelike.
CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
GB - 6
CONTROL REFERENCE GUIDE
Remote Control
1) VIDEO MODE Button
Adjusts Brightness, Contrast or Color of the LCD
screen.
2) PREV button
Moves back through titles, chapters or tracks on a
disc.
3) / SEARCH Buttons
SEARCH: Fast reverse playback.
SEARCH: Fast forward playback.
4) GOTO Button
Skips directly to a location on a DVD.
5) Cursor ( , , , ) Buttons
Use to move between selections on a menu
screen and adjust certain settings.
ENTER Button
Confirms selections on a menu screen.
6) MEMORYButton
In STOP mode, sets titles/chapters in a favorite
order.
7) Number (0 - 9) Buttons
Use when creating programs, entering parental
control password or locating a title/chapter/track
or specific time.
8) REPEAT A-B Button
Performs point-to-point repeat playback on a DVD
or CD.
REPEAT DISC Button
Repeats a DVD chapter or title.
Repeats a CD track or the entire disc.
SETUP Button
In stop mode, it brings up the unit’s SETUP
menu.
9) SUBTITLE Button
Selects one of the subtitle languages programmed
on a DVD (if available).
RETURN Button
Returns to normal operation after using the
SETUP menu of a DVD.
10) AUDIO Button
Selects one of the audio sound tracks on a
DVD (if more than one is available) or select the
audio output mode on a CD.
11) ANGLE Button
Switches between multiple camera angles when
the DVD you are playing has been programmed
with multiple camera angles.
12) DISPLAYButton
Shows status information on the screen.
13) STOP Button
Stops playing a disc.
PLAYButton
Starts or resumes playback of a disc.
PAUSE Button
Pauses playback and frame advance.
14) NEXT Button
Moves forward through titles, chapters or tracks
on a disc.
15) MENU Button
Enters and exits the main DVD menu.
GB - 7
DVD Player
CONTROL REFERENCE GUIDE
1) Left Speaker
2) SCREEN ROTATE Button
Flips the screen 180°.
3) SEARCH Button
Performs fast reverse playback.
4) SEARCH Button
Performs fast forward playback.
5) PREV Button
Goesbackwardstopreviouschapters/tracks.
6) NEXT Button
Advanceschapters/tracks.
7) STOP Button
Stops playing a disc.
8) PAUSE Button
Pauses playback and frame advance.
9) PLAY Button
Starts or resumes playback of a disc.
10) Right Speaker
11) "ON" Indicator
WhentheCHARGE/STANDBY/ONswitchisin
the ON position, the green light will illuminate.
Indicator
When the CHARGE / STANDBY / ON switch
is in the CHARGE position, the red light will
illuminate.
Remote Sensor
Receives the remote control signal.
12) Headphone Jack
13) VOLUME Control
Adjusts the volume.
14) CHARGE / STANDBY / ON Switch
15) AUDIO IN / OUT and VIDEO IN/OUT Jacks
16) DVD / AV IN Switch
17) DC IN 9V-12V Jack
2
1
3456789
11
10 12
13
14
15
16
17
GB - 8
CONTROL REFERENCE GUIDE
Monitor
1) VOLUME Control
Adjusts the volume.
2) Headphone Jack
3) Left Speaker
4) Right Speaker
5) AUDIO / VIDEO IN Jacks
6) DC OUT 9-12V Jack
7) POWER ON Indicator
When the STANDBY / ON switch is in the ON
position, the green light will illuminate.
8) Stand
9) BRIGHTNESS Control
Adjusts the relative lightness or darkness of the
screen.
10) COLOR Control
Adjusts the color intensity.
11) Screen Switch
WIDE: Wide Screen
NORMAL: Pan Screen
12) ON / OFF Switch
13) DC IN 9-12V Jack
1 2 43
9
10
11
12
13
7
8
5
6
GB - 9
POWER SUPPLY
A. Using the Car Power Adapter
The included 12V car power adapter is designed for use with vehicles that have a 12V, negative ground
electrical system.
Using the Main Unit and the Monitor together
Using the Main Unit or the Monitor separately
Cautions:
•Usethisunitonlywiththeincluded12Vcarpoweradapter.Usewithothercaradapterscould
damage the unit, or even your vehicle.
•Theincluded12Vcarpoweradapterisforusewiththisunitonly.Donotuseitwithanyother
equipment.
• Intheinterestoftrafcsafety,driversshouldnotoperatetheunitorviewvideoswhiledriving.
• Whentheinsideofthe12Vcarsocketisdirtywithashesordust,theplugsectionmaybecomehotdue
to poor contact. Be sure to clean the 12V car socket before use.
• Afteruse,disconnectthe12Vcarpoweradapterfromboththeunitandcigarettelightersocket.
• Iftheunitisnotproperlyattachedtoavehicle,itmaybecomeairborneintheeventofanaccidentand
cause damage, injury, or death.
• Checkyourlocaltrafclawsforrulesgoverningtheuseofvideodevicesinvehicles.
IMPORTANT
This car adapter is for use
with 12 volt batteries only.
WARNING:
Disconnect this car power adapter when not
in use. Not for use in 24V vehicles.
To the cigarette
ligher socket
2
Car Power Adapter
To DC IN 9V-12V jack
Right side
of Monitor
1
To the cigarette
ligher socket
2
Car Power Adapter
To DC IN 9V-12V jack
DVD player
Left side
of Monitor
Right side
of Monitor
1
AV-DC cable
GB - 10
POWER SUPPLY
Cautions:
• The AC adapter included with this unit is for its use only. Do not use it with other equipment.
• Turn off the unit before unplugging the AC adapter from the unit so as to avoid the unit being damaged.
• When the unit is not going to be used for long time, disconnect the AC adapter from the wall outlet.
IMPORTANT
• Be sure to use it near an easily accessible wall outlet. If a malfunction occurs, disconnect the plug from
the wall outlet at once.
• When the AC adapter is plugged in, the apparatus is not completely disconnected from the main power
source, even when the unit is turned off.
B. Using the AC Power Adapter
The included AC power adapter operates on AC between 100V and 240V.
• The supplied AC adapter is suitable for use on AC mains supplies of 100-240 Volts AC and should only be
connected to a mains supply within these parameters.
Using the Main Unit and the Monitor together
Using the Main Unit or the Monitor separately
To DC IN 9V-12V jack
AC Adapter
T
o AC outlet
2
DVD player
Left side
of Monitor
Right side
of Monitor
AV-DC cable
1
AC Adapter
To AC outlet
1
2
To DC IN 9V-12V jack
Right side
of Monitor
AC Adapter
To AC outlet
1
2
DVD player
To DC IN 9V-12V jack
GB - 11
C. Using the Built-in Battery
The unit has a built-in, non-replaceable, rechargeable battery. Charge the built-in battery before using it for
the first time. The normal charging time should be completed within 3-4 hours. The red charging light will go
out when the built-in battery becomes fully charged.
To Recharge the Built-in Battery
WARNING
• The built-in battery should not be exposed to excessive heat such as sunshine, or the like.
• The built-in battery presents a risk of or chemical burn if mistreated. Do not disassemble, place near a
source 212°F (100°C), or incinerate.
• Dispose the unit with built-in battery properly. Environmental problems must be considered and local rules
or laws governing the disposal must be strictly followed.
CAUTION
• The built-in battery can only be recharged when the unit is in CHARGE mode while using the AC adapter.
• The built-in battery cannot be recharged when the unit is in power ON mode.
• Do not recharge the battery in the vehicle by using the car power adapter.
• When the built-in battery power is low, "BATTERY LOW" will appear on the screen and the unit will stop
playing.
• Recharge the built-in battery when you are ready to use it again.
• While using the built-in battery, the environmental temperature should be 41°F (5°C) to 95°F (35°C).
• To get the longest service life of the built-in battery, charge at indoor temperature.
GB - 12
CONNECTIONS
Watching a DVD on your TV
1. Connect your TV to the main unit using a standard AV Cable (not included).
2. Turn on the main unit and slide the AV IN / DVD switch to the DVD position.
3. Turn on the TV and follow the instructions included with it to play the DVD.
Notes:
• Make sure to use the correct Audio/Video cable. Connecting the plugs incorrectly may cause a weak
signal.
• If your TV does not have Audio/Video inputs, you will need to purchase an RF modulator (sold separately)
and follow the instructions included with it to connect the unit to your TV.
B. Connecting a TV (for the Main Unit Only)
If your TV has Audio/Video inputs, you can connect the main unit to your TV using a standard A/ V cable (not
included).
A. Watching a DVD on the Main Unit and the Monitor
You can watch the same DVD on the main unit and the monitor.
Watching a DVD on the Main Unit and the Monitor
1. Connect the main unit and the monitor using the included DC-AV Cable.
2. Slide the AV IN / DVD switch to the DVD position.
3. Turn on the main unit and the monitor.
4. Play a DVD on the main unit; the monitor will play at the same time.
Note: You can also use the included AC power adapter to supply power.
DVD player
Left side
of Monitor
AV-DC cable
DVD player
AV-DC cable
TV
CONNECTIONS
Watching video equipment
1. Connect the other equipment to the monitor using a standard AV Cable (not included).
2. Turn on the monitor.
3. Turn on the video equipment and follow the instructions provided with it to playback.
Notes:
•
Make sure to use the correct Audio/Video cable. Connecting the plugs incorrectly may cause a weak signal
• If you have a mono VCR, the volume level from the speakers will be low.
E. Connecting Game Systems/Video Equipment (for the Monitor Only)
You can connect game systems or other video equipment for playback through the monitor.
C. Connecting a Stereo Receiver or Amplifier (for the Main Unit Only)
The main unit can play two channels Dolby Digital.
Listening on External Audio Equipment
1. Connect the main unit to the left / right
Audio In jacks on the other equipment
using a standard Audio cable (not included).
2. Turn on the main unit and slide the
AV IN / DVD switch to the DVD position.
3. Turn on your audio equipment and follow the
instructions provided with it to select the
AUDIO IN function.
Notes:
• Make sure to use the correct Audio cable. Connecting the plugs incorrectly may cause a weak signal.
• If you have a stereo VCR, make sure you set it to stereo mode.
• Due to copyright protection, DVD movies cannot be copied. If you copy a DVD movie onto a videotape, the
resulting copy will be unclear, with poor sound quality. This is NOT caused by a defective DVD system.
er
AV-DC cable
DVD play
Stereo Receiver /
AV cable
(not included)
Game System /
Video Equipment
Watching video equipment
1. Turn on the unit and slide the AV IN / DVD switch to the AV IN position.
2. Turn on the video equipment and follow the instructions provided with it
to playback.
D. Connecting to a video equipment (for the Main Unit only)
You can connect other video equipment for playback through the unit.
DVD player
Video
equipment
White Red Yellow
AV cable
(not included)
To AUDIO / VIDEO
IN / OUT caks
GB - 13
GB - 14
F. Using the Monitor with Other Equipment while Playing DVD on the Main Unit
You can use a game console or other video equipment on the monitor while playing a DVD on the main unit.
CONNECTIONS
Watching Video Equipment on the Monitor while Playing DVD on the Main Unit
1. Connect only the power connector between the main unit and the monitor. Do not connect the Audio/Video
portion of the DC-AV cable.
2. Connect the monitor to the other equipment using a standard AV cable (not included).
3. Turn on the main unit, the monitor and the other equipment.
4. Slide the AV IN / DVD switch to the DVD position.
5. Play a DVD on the main unit.
6. Use the monitor for the other equipment.
Notes:
• You can also use the included AC power adapter to supply power.
• Make sure to use the correct Audio/Video cable. Connecting the plugs incorrectly may cause a weak
signal.
• If you have a mono VCR, the volume level from the speakers will be low.
G. Using Headphones/Earphones
Turn down the volume before connecting the
headphones/earphones. Slowly raise the volume
with the headphones on until you reach your
desired volume. When headphones are connected,
the speaker is automatically disabled.
Caution:
• Avoid listening to sound at excessive levels which
could be harmful to your ears.
Left side
of Monitor
Right side
of Monitor
DVD player
AV-DC cable
Game System /
Video Equipment
Connect to Car
Power Adapter or AC
Adapter
GB - 15
Mounting in the Vehicle
Use the supplied mounting straps to install the main unit and monitor on the back of the vehicle's headrests.
Tightly wrap the mounting strap around the headrest.
SAFETY WARNING!
• Thisunitshouldneverbeusedbythevehicle'sdriverorleftunsecuredinthevehiclewhiledriving.
• Ifthisunitisbeingusedinyourvehicle,besurethatitissecuredorheldsafely,anddoesnotobstructany
safety device, including air bags or seat belts.
• Allpassengersshouldwearseatbeltswhenusingthisunitinamovingvehicle.
• Ifindoubt,pleasecontactyourvehiclemanufacturerforfurtheradvice.
MOUNTING IN THE VEHICLE
Adjusting viewing angle
Mounting strap
GB - 16
UNIT OPERATION
Turning on the Unit
1.SlidetheCHARGE/STANDBY/ONswitchonthemainunittotheON,slidetheON/OFFswitchonthe
monitor to the ON.
2. The start-up picture will appear on the screen of the main unit.
3.Afteruse,slidetheCHARGE/STANDBY/ONswitchonthemainunittoSTANDBY(poweroff),slidethe
ON/OFFswitchonthemonitortotheOFF.
SOUND SYSTEM
Dolby Digital
Dolby Digital is a technology developed by Dolby Laboratories. Soundtracks encoded in Dolby Digital can
reproduce from one to 5.1 discrete channels of excellent quality audio.
The unit automatically recognizes the Dolby Digital bitstream and provides a downmix suitable for two-
channel listening. An additional Dolby Digital decoder is required for reproduction of the discrete multi-channel
soundtracks available on many DVDs.
Manufactured under license from Dolby Laboratories.
'Dolby' and the double-D symbol are trademarks of Dolby Laboratories.
USING THE STAND FOR DESKTOP USE
Youcanstandthemonitoruponadeskortableusingthestandontheback.
GB - 17
Playing a Disc
1.SlidetheCHARGE/STANDBY/ONswitchtotheONposition.SlidetheON
/ OFF switch on the monitor to the ON position. See CUSTOMIZINGTHE
FUNCTION SETTINGS before proceeding to step 2.
2. Pull down front panel to open the disc door.
3. Hold the disc by its sides and gently push it onto the spindle, with label side
facingtowardyouuntilyouheara“click”.
4. Gently push the disc door closed. It takes a short while for your unit to load
the disc. After loading, for most DVDs, the unit will automatically take you main
menu or start playing. If the unit does not automatically start playing the DVD,
press the PLAYbutton.
Pausing Playback (Still Mode)
Press the PAUSE button. To resume normal playback, press the PLAY
button.
Each time you press the PAUSE button, the picture advances one frame.
Stopping Playback
Press the STOP button at the location where you want to interrupt playback. To resume playback at the
position where the disc was stopped, press the PLAYbutton.
If you press the STOP button twice, the unit’s memory will be cleared and pressing the PLAYbuttonwill
reset the disc to the beginning.
Fast Forward / Fast Reverse
1. Press the SEARCH or SEARCH button when a disc is playing. Each time you press the SEARCH
or SEARCH button, the playback speed changes in the following sequence:
2. Press the PLAYbuttonwhenyoureachthedesiredpointtoresumenormalplayback.
Note:
• TheDVDplayermutessoundandsubtitlesduringreverseandforwardscanofDVDs.
• Thefastplaybackspeedmaydifferdependingonthedisc.
Skip (Forward / Reverse)
• Pressthe PREVbuttontogobacktocurrentorpreviouschapters/tracks.
• Pressthe NEXTbuttontoadvancechapters/tracks.
• ForaudioCDs,usethenumberbuttonsontheremotecontroltojumpimmediately
to the desired track number.
Audio Selection
On some DVDs, the sound is recorded in two or more formats. Follow the directions below to select the
preferred language and sound system.
1. While a disc is playing, press the AUDIO button to show the current audio format number.
2. Press the AUDIO button repeatedly to select the desired audio format.
Note:
• IfonlyoneaudioformatisrecordedontheDVD,thenumberdoesnotchange.
• SomeDVDsallowyoutochangeaudioselectionsusingthediscmenuonly.Ifthisisthecase,pressthe
MENU button and choose the appropriate language on the disc menu.
• You canselectdifferentaudiochannels (Stereo,LeftorRight)onanAudioCDbypressingtheAUDIO
button repeatedly.
This owner’s manual explains the basic instructions
for operating this unit. Some DVDs are produced in
a manner that allows specific or limited operation
during playback. Therefore, this unit may not
respond to all operating commands. THIS IS
NOT A DEFECT. Please refer to the instructions
accompanying the specific DVD in question for
more information about the options available on
that DVD.
“ ”mayappearonthescreenduringoperation.
A “ ” means that the desired operation is not
permitted by the unit or disc.
PLAYING A DISC
Basic playback
GB - 18
PLAYING A DISC
Basic playback
Subtitle Selection
1. While a DVD is playing, press the SUBTITLE button to display the current language setting, as shown in
the example.
2. Press the SUBTITLE button repeatedly to select the desired subtitle language. You can turn subtitles off by
pressing the SUBTITLE button repeatedly until the “
” is displayed.
Note:
• Some DVDs are set to display subtitles automatically, and you cannot turn them off even if you set the
subtitle function to off.
• During some scenes, the subtitles may not appear immediately after you select your desired scene.
• The number of subtitle languages recorded differs depending on the disc. If only one language is recorded,
the language does not change.
• This function can only be used for discs on which subtitles have been recorded in multiple languages.
• Some DVDs allow you to change subtitles using the disc menu only. If this is the case, press the MENU
button and choose the appropriate subtitle on the disc menu.
Angle Selection
Some DVDs contain scenes which have been shot from a number of different angles. For these discs, the
same scene can be viewed from each of these different angles.
1. While you are playing a DVD with different angles recorded, press the ANGLE button to view the number
of current angles available.
2. Press the ANGLE button repeatedly to change the scene to the next
recorded angle.
• After approx. t
wo seconds, playback will continue from the new angle
you selected.
• If no button is pressed within 10 seconds, playback continues without
changing the current angle.
Note:
• This function can only be used for discs on which scenes shot from
multiple angles have been recorded.
• If only one angle is recorded, “
” is displayed.
Display Function
While the disc is playing, press the DISPLAY button repeatedly to display
information on operation status.
Elapsed Time: Elapsed time from the beginning of the title which is
currently playing.
Remain Time: Remaining time of the title which is currently playing.
Adjust the LCD Screen
You can adjust Brightness, Contrast or Color of the LCD screen.
1. Press the VIDEO MODE button.
2. Press the /
button to select Brightness, Contrast, Color or View Mode.
3. Then press the
/ button to change the setting (For View Mode, press the ENTER button to change the
setting).
4. Press the VIDEO MODE button to exit the menu.
Note:
For the monitor, you can adjust the LCD screen by the BRIGHTNESS control, COLOR control and Screen
(WIDE / NORMAL) switch on the monitor.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

RCA DRC6389T User manual

RCA
Brand
RCA
Model
DRC6389T
Category
DVD players
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents