Aiwa CX-NA31 User manual

aiwa(1)

COMPACT DISC STEREO SYSTEM

CX-NA50

- For NSX-A54 and NSX-A50

OPERATING INSTRUCTIONS

For Assistance and Information

Call Toll Free 1-800-BUY-AIWA

(United States and Puerto Rico)

English pg. 1

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN

OR MOISTURE.

"CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL."

Explanation of Graphical Symbols:

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the

user to the presence of uninsulated "dangerous voltage" within the product's inclosure that may be of sufficient

magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of

important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Owner's record

For your convenience, record the model number and serial number (you will find them on the rear of your set) in the

space provided below. Please refer to them when you contact your Aiwa dealer in case of difficulty.

Model No. Serial No. (Lot No.)

CX-NA50

SX-NA54

SX-R210 (NSX-A54 only)

PRECAUTIONS

Read the Operating Instructions carefully and completely before operating the unit. Be sure to keep the Operating

Instructions for future reference. All warnings and cautions in the Operating Instructions and on the unit should be

strictly followed, as well as the safety suggestions below.

Installation

1 Water and moisture

- Do not use this unit near water, such as near a bathtub, washbowl, swimming pool, or the

like

2 Heat

- Do not use this unit near sources of heat, including heating vents, stoves, or other appliances that generate

heat. It also should not be placed in temperatures less than 5ºC (41ºF) or greater than 35 Cº(95ºF).

3 Mounting Surface

- Place the unit on a flat, even surface

4 Ventilation

- The unit should be situated with adequate space around it so that proper heat ventilation is assured.

Allow 10 cm (4 in.) clearance from the rear and then tope of the unit, and 5 cm (2 in.) from each side.

- Do not place the unit on a bed, rug, or similar surface that may block the ventilation openings.

- Do not install the unit in a bookcase, cabinet, or airtight rack where ventilation may be impeded.

5 Objects and liquid entry

- Take care that objects of liquids do not get inside the unit through the ventilation

openings.

6 Carts and stands

- When placed or mounted on a stand or cart, the unit should be moved with care. Quick stops,

excessive force, and uneven surfaces may cause the unit or cart to overturn or fall.

7 Condensation

- Moisture may form on the CD pickup lens when:

- The unit is moved from a cold spot to a warm spot

- The heating system has just been turned on

- The unit is used in a very humid room

- The unit is cooled by an air conditioner

When this unit has condensation inside, it may not function normally. Should this occur, leave the unit for a few

hours, then try to operate again.

8 Wall or ceiling mounting

- The unit should not be mounted on a wall or ceiling, unless specified in the Operating

Instructions

Electric Power

1 Power sources

- Connect this unit only to power sources specified in the Operating Instructions, and as marked on

the unit.

2 Polarization

- As a safety feature, some units are equipped with polarized AC power plugs which can only be

inserted one way into a power outlet. If it is difficult or impossible to insert the AC power plug into an outlet, turn

the plug over and try again. If it still does not easily insert into the outlet, please call a qualified service technician to

service or replace the outlet. To avoid defeating the safety feature of the polarized plug, do not force it into a power

outlet.

3 AC power cord

- When disconnecting the AC power cord, pull it out by the AC power plug. Do not pull the cord itself.

- Never handle the AC power plug with wet hands, as this could result in fire or shock.

- Power cords should be routed to avoid being severely bent, pinched, or walked upon. Pay particular attention to

the cord from the unit to the power socket.

- Avoid overloading AC power plugs and extension cords beyond their capacity, as this could result in fire or shock.

PRECAUTIONS (cont.) pg. 2

4 Extension cord

- To help prevent electric shock, do not use a polarized AC power plug with an extension cord,

receptacle, or other outlet unless the polarized plug can be completely inserted to prevent exposure of the blades of

the plug.

5 When not in use

- Unplug the AC power cord form the AC power plug if the unit will not be used for several

months or more. When the cord is plugged in, a small amount of current continues to flow to the unit, even when the

power is turned off.

Outdoor Antenna

1 Power lines

- When connecting an outdoor antenna, make sure it is located away from power lines.

2 Outdoor antenna grounding

- Be sure the antenna system is properly grounded to provide protection against

unexpected voltage surges or static electricity build-up. Article 810 of the National Electrical Code, ANSI/NFPA 70,

provides information on proper grounding of the mast, supporting structure, and the lead-in wire to the antenna

discharge unit, as well as the size of the grounding unit, connection to grounding terminals, and requirements for

grounding terminals themselves.

Maintenance

Clean the unit only as recommended in the Operating Instructions

Damage requiring Service

Have the units serviced by a qualified service technician if:

- The AC power cord or plug has been damaged

- Foreign objects or liquid have gotten inside the unit

- The unit has been exposed to rain or water

- The unit does not seem to operate normally

- The unit exhibits a marked change in performance

- The unit has been dropped, or the cabinet has been damaged

DO NOT ATTEMPT TO SERVICE THE UNIT YOURSELF

TABLE OF CONTENTS

PRECAUTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

PREPARATIONS

CONNECTIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

REMOTE CONTROL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

BEFORE OPERATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

SOUND

AUDIO ADJUSTMENTS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

GRAPHIC EQUALIZER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

RADIO RECEPTION

MANUAL TUNING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

PRESETTING STATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

CD PLAYING

BASIC OPERATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

PROGRAMMED PLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

TAPE PLAYBACK

BASIC OPERATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

CONTINUOUS PLAY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

RECORDING

BASIC RECORDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

DUBBING A TAPE MANUALLY. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

DUBBING THE WHOLE TAPE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

AI EDIT RECORDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

PROGRAMMED EDIT RECORDING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

KARAOKE

MICROPHONE MIXING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

KARAOKE PROGRAM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

CLOCK AND TIMER

SETTING THE CLOCK. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

SETTING THE TIMER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

SETTING THE SLEEP TIMER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

OTHER CONNECTIONS

CONNECTING OPTIONAL EQUIPMENT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

LISTENING TO EXTERNAL SOURCES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

GENERAL

CARE AND MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

TROUBLESHOOTING GUIDE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

PARTS INDEX. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover

CONNECTIONS pg. 3

Check your system and accessories

Before connecting the AC cord

The rated voltage of you unit shown on the rear panel is 120 V AC. Check that the rated voltage matches your local

voltage

IMPORTANT

Connect the speakers, antennas, and all optional equipment first. Then connect the AC cord in the end.

1 Connect the right and left speakers to the main unit.

Connect the right speaker cord to the SPEAKERS R terminals, and left to the SPEAKERS L terminals.

The speaker cord with the white stripes should be connected to the + terminal and the black cord to the - terminal.

Speaker Hookup Illustration

PREPARATIONS (cont.) pg. 4

2 Connect the surround speakers to the main unit. (only for NSX-A54)

There are no differences between the surround speakers. Connect each surround speaker cord to the SURROUND

SPEAKERS R or L terminal.

3 Connect the supplied antennas.

Connect the FM antenna to the FM 75

Ω

terminals and the AM antenna to the AM LOOP terminals.

4 Connect the AC cord to an AC outlet.

To position the antennas

FM feeder antenna:

Extend this antenna horizontally in a T-shape and fix its ends to the wall.

AM loop antenna:

Position to find the best reception.

To stand the AM antenna on a surface

Fix the claw to the slot

NOTE

• Be sure to connect the speaker cords correctly. Improper connections can cause short circuits in the SPEAKERS

terminals.

• Do not leave objects generating magnetism near the speakers as these object may be damaged.

• Do not bring the FM antenna near metal objects or curtain rails.

• Do not bring the AM antenna near other optional equipment, the stereo system itself, the AC cord or the speaker

cords, since noise will be picked up.

• Do not unwind the AM antenna wire.

POSITIONING THE SPEAKERS (NSX-A54 only)

Position the speakers to make the most of the SURROUND effect.

Standard Positioning

Front speaker (Right)

Front speaker (Left)

Surround speakers

Place the surround speakers behind the listening area.

To mount the surround speakers on the wall

Mount each speaker on a spot that can hold its weight.

NOTE

Sound is not heard from the surround speakers when the SURROUND is set off.

CONNECTING AN OUTDOOR ANTENNA

For better FM reception, use of an outdoor antenna is recommended.

Connect the outdoor antenna to the FM 75

Ω

terminals.

To connect other optional equipment

→

page 21.

PREPARATIONS (cont.) pg. 5

REMOTE CONTROL

Inserting batteries

Detach the battery cover on the rear of the remote control and insert two R6 (size AA) batteries.

When to replace the batteries

The maximum operational distance between the remote control and the sensor on the main unit should be

approximately 5 meters(16 feet). When this distance decreases, replace the batteries with new ones.

To use the SHIFT button on the remote control

Buttons 1 have different functions. One of these functions is indicated on the button, and the other on the plate

above the button.

To use the function on the button, simply press the button.

To use the function on the plate above the button, press the button while pressing the SHIFT button.

To use the FUNCTION button on the remote

The FUNCTION button substitutes for the function buttons (TAPE/DECK 1/2, TUNER, VIDEO/AUX, MD,CD) on

the main unit. Each time the FUNCTION button is pressed, the next function is selected cyclically. When tapes are

inserted in both decks, both decks are selected with the FUNCTION buttons.

The / PRESET button on the remote control

The function is the same as that of the DIRECTION/PRESET button on the main unit.

NOTE

• If the unit is not going to be used for an extended period of time, remove the batteries to prevent possible

electrolyte leakage.

• The remote control may not operate correctly when:

- The line of sight between the remote control and the remote sensor inside the display window is exposed to

intense light, such as direct sunlight.

- Other remote controls are used nearby (those of a television, etc.)

BEFORE OPERATION

To turn the unit on

Press one of the function buttons (TAPE, TUNER, VIDEO/AUX,CD, MD).

Playback of the inserted disc or tape begins, or the previously tuned station is received (Direct Play Function).

The POWER button is also available.

When the unit is turned on, the disc compartment may open and close to reset the unit.

DEMO (Demonstration) mode

When the AC cord is connected, the display window demonstrates the functions of the unit. When the power is

turned on, the DEMO display is overridden by the operation display. When the power is turned off, the DEMO

mode is restored.

To cancel DEMO mode

Press the DEMO button. The clock display appears. (To set the current time, see "SETTING THE CLOCK" on

page 19.) To re-activate the DEMO mode, press the DEMO button again.

Illumination guides

Whenever the AC cord is connected or one of the function buttons is pressed, the buttons for that operation light up

or flash. Example: When the AC cord is connected, the SET button flashes as a guide to setting the current time.

Flash windows

The windows on the top of the unit and the cassette decks light up or flash while the unit is being powered on.

To turn off the light of the top window, press the button while pressing the CD button. To turn back on, repeat

the above.

To turn the unit off

Press the POWER button.

SOUND pg. 6

AUDIO ADJUSTMENTS

VOLUME

Turn the VOLUME control on the main unit, or press the VOLUME button on the remote control.

The volume level is displayed as a number from 0 to MAX (31).

The volume level is automatically set to 16 when the power is turned off with the volume level set to 17 or more.

BBE SYSTEM

The BBE system enhances the clarity of high-frequency sound. It also enriches the KARAOKE function to make

your voice sound clear and pleasant.

Press the BBE button.

Each time it is pressed, the level changes. Select one of the three levels, or the off position to suit your preference.

SUPER T-BASS SYSTEM

The T-BASS system enhances the realism of low-frequency sound.

Press the T-BASS button.

Each time it is pressed, the level changes. Select one of the three levels, or the off position to suit your preference.

NOTE

Low frequency sound may be distorted when the T-BASS system is used for a disc or tape in which low frequency

sound is originally emphasized. In this case, cancel the T-BASS system.

GRAPHIC EQUALIZER

This unit provides the following three different equalization curves.

ROCK: Powerful sound emphasizing treble and bass

POP: More presence in the vocals and midrange

CLASSIC: Enriched sound with heavy bass and fine treble

Press the GEQ buttons.

To cancel the selected mode

Press the GEQ button repeatedly so that GEQ OFF appears on the display.

To select with the remote control

Press the GEQ button repeatedly while pressing the SHIFT button. The GEQ mode is displayed cyclically as

follows.

Using the headphones

Connect headphones to the PHONES jack with a stereo standard plug (ø6.3 mm, 1/4 inch.)

No sound is output from the speakers while the headphones are plugged in.

Sound adjustment during recording

The output volume and tone (except BBE) of the speakers or headphones may be freely varied without affecting the

level of the recording.

NOTE

When playing back a tape recorded with BBE, it is recommended that BBE be set to off to avoid distorted high

frequency sound.

RADIO RECEPTION pg. 7

MANUAL TUNING

1 Press the TUNER/BAND button repeatedly to select the desired band.

When the TUNER/BAND button is pressed while the power is off, the power is turned on directly.

To select a band with the remote control

Press the BAND button while pressing the SHIFT button.

2 Press the DOWN or UP button to select a station.

Each time the button is pressed, the frequency changes. When a station is received, "TUNE" is displayed for 2

seconds. During FM stereo reception, is displayed.

To search for a station quickly (Auto Search)

Keep the DOWN or UP button pressed until the tuner starts searching for a station. After tuning in to a

station, the search stops.

To stop the Auto Search manually, press the DOWN or UP button.

• The Auto Search may not stop at stations with very weak signals.

When an FM stereo broadcast contains noise

Press the MONO TUNER button while pressing the SHIFT button on the remote so that "MONO" appears on the

display.

Noise is reduced, although reception in monaural.

To restore reception, press these buttons so that MONO disappears.

PRESETTING STATIONS

The unit can store a total of 32 preset stations. (Each band has a maximum of 20 available preset stations.) When a

station is stored, a preset number is assigned to the station. Use the preset number to tune in to a preset station

directly.

1 Press the TUNER/BAND button to select a band, and press the DOWN or UP button select a

station.

2 Press the SET button to store the station.

A station is assigned a preset number, beginning from 1 in consecutive order for each band.

3 Repeat steps 1 and 2.

The next station will not be stored if a total of 32 preset stations for all the bands or a total of 20 preset stations for

one band have already been stored.

RADIO RECEPTION (cont.) pg. 8

PRESET NUMBER TUNING

Use the remote control to select the preset number directly.

1 Press the TUNER/BAND button to select a band.

2 Press the numbered buttons to select a preset number.

Example:

To select preset number 20, press the +10, +10 and 0 buttons.

To select preset number 15, press the +10 and 5 buttons.

Selecting a preset number on the main unit

Press the TUNER/BAND button to select a band. Then, press the DIRECTION/PRESET button repeatedly.

Each time the button is pressed, the next ascending number is selected.

To clear a preset station

Select the preset number of the station to be cleared. Then, press the CLEAR button, and press the SET

button within 4 seconds.

The preset numbers of all other stations in the band with higher numbers are also decreased by one.

To change the AM tuning interval

The default setting of the AM tuning interval is 10 kHz/step. If you use this unit in an area where frequency

allocation system is 9 kHz/step, change the tuning interval.

Press the POWER button while pressing the TUNER/BAND button.

To reset the interval, repeat this procedure.

NOTE

When the AM tuning interval is changed, all preset stations (see "PRESETTING STATIONS")are cleared. The

preset stations have to be set again.

CD PLAYING pg. 9

BASIC OPERATIONS

LOADING DISCS

Press the CD button, then press the OPEN/CLOSE button to open the disc compartment. Load disc (s)

with the label side up.

To play one or two discs, place the discs on the tray 1 and 2.

To play three discs, press the DISC CHANGE button to rotate the trays after placing two disc. Place the third disc

on tray 3. Close the disc compartment by pressing the OPEN/CLOSE button.

PLAYING DISCS

Load discs.

To play all discs in the disc compartment, press the button.

Play begins with the disc on tray 1.

To play one disc only, press one of the DISC DIRECT PLAY buttons.

The selected disc is played once.

To stop play, press the button.

To pause play, press the button. To resume play, press again.

To search for a particular point during playback, keep the or button pressed and release the button at

the desired point.

To skip to the beginning of a track during playback, press the or button repeatedly.

To remove discs, press the OPEN/CLOSE button.

To start play when the power is off (Direct Play Function)

Press the CD button. The power turns on and play of the loaded disc begins.

When the OPEN/CLOSE button is pressed, the power is also turned on.

To check the remaining time

During play, press the CD EDIT CHECK button on the main unit or the EDIT/CHECK button on the remote control

while pressing the SHIFT button. The amount of time remaining until all tracks finish playing is displayed. To

restore the playing time display, repeat the above again.

Selecting a track with the remote control

1 Press one of the DISC DIRECT PLAY buttons to select a disc.

2 Press the numbered buttons and the +10 button to select a track.

Example:

To select the 25th tack, press the +10, +10 and 5 buttons.

To select the 10th track, press the +10 and 0 buttons.

The selected track starts to play and play continues to the end of that disc.

Replacing discs during play

While one disc is playing, the other discs can be replaced without interrupting play.

1 Press the DISC CHANGE button.

2 Remove the discs and replace with other discs.

3 Press the OPEN/CLOSE button to close the disc compartment.

NOTE

• When loading an 8-cm (3-inch) disc, put it onto the inner circle of the tray.

• Do not place more than one compact disc on one disc tray.

• Do not tilt the unit with discs loaded. Doing so may cause malfunctions.

CD PLAYING (cont.) pg. 10

RANDOM/REPEAT PLAY

Use the remote control.

RANDOM play

All the tracks on the selected disc or on all the discs can be played randomly.

REPEAT play

A single disc or all the discs can be played repeatedly.

Press the RANDOM/REPEAT button while pressing the SHIFT button.

Each time it is pressed, the function can be selected cyclically.

RANDOM play - RANDOM lights up on the display.

REPEAT play - lights up on the display.

RANDOM/REPEAT play - RANDOM and light up on the display.

Cancel - RANDOM and go out from the display.

NOTE

During random play following operations are not possible:

- to select the tracks directly with the numbered buttons.

- to skip to the previously played track with the button.

PROGRAMMED PLAY

Up to 30 tracks can be programmed from any of the inserted disc.

Use the remote control

1 Press the PRGM button twice while pressing the SHIFT button in stop mode.

The PRGM indicator flashes on the display.

• When the PRGM button is pressed once in step 1, the unit enters the KARAOKE PROGRAM (page 20).

2 Press one of the DISC DIRECT PLAY buttons to select a disc.

The selected disc is indicated in red on the display.

Go to the next step when the tray stops rotating.

3 Press the numbered buttons and the +10 button to program a track.

Example:

To select the 25th track, press the +10, +10 and 5 buttons.

To select the 10th track, press the +10 and 0 buttons.

4 Repeat steps 2 and 3 to program other tracks.

5 Press the button to start play.

To check the program

Each time the or button is pressed in stop mode, a disc number, track number, and program number will

be displayed.

To clear the program

Press the CLEAR button in stop mode.

To add tracks to the program

Before playing, repeat steps 2 and 3. The track will be programmed after the last programmed track,

To change the programmed tracks

Clear the program and repeat all the steps again.

NOTE

During programmed play, you cannot perform random play, check the remaining time, and select a disc or track.

TAPE PLAYBACK pg. 11

BASIC OPERATIONS

• On deck 1, tapes are always played back on both sides.

• On deck 2, you can select a reverse mode to play back one or both sides.

• Use Type I (normal), Type II (high/CrO

2

)or Type IV (metal) tapes for playback.

1 Press the TAPE button and press the EJECT mark to open the cassette holder.

Insert a tape with the exposed side down. Push the cassette holder to close.

2 Press the button to start play.

: The front side is being played (forward).

: The back side is being player (reverse).

To select a reverse mode (deck 2 only)

Each time the REV MODE button is pressed, the reverse mode changes.

To play one side only, select .

To play from front side to reverse side once only, select .

To play both sides repeatedly, select .

• When tapes are loaded in both decks, on the display indicates Continuous Play.

When tapes are loaded in both decks

Press the TAPE button first to select a deck.

The selected deck number is displayed.

To stop play, press the button.

To pause play (deck 2 only), press the button. To resume play, press again.

To change the playback side, press the DIRECTION/PRESET button in play or pause mode.

To fast forward or rewind, press the or button in stop mode. Then press the button to stop the tape.

To start play when the power is off (Direct Play Function)

Press the TAPE button. The power is turned on and play of the inserted tape begins.

To set the tape counter to 0000

Press the CLEAR button in stop mode.

The counter is also set to 0000 when the cassette holder is opened.

MUSIC SENSOR

If there is a 4-second or longer blank between each track, a search for the beginning of the current or next track

during playback can be done easily.

Press the or button during playback referring to the playback side indicator ( or )on the display.

For example, when the button is pressed while is displayed, playback of the next track starts.

Music sensor function may not be able to detect tracks under the following conditions:

• Blanks of less than 4 seconds between tracks

• Noisy blanks

• Long passages of low-end sound

• Low overall recording levels

TAPE PLAYBACK (cont.) pg. 12

CONTINUOUS PLAY

After playback on one deck finishes, the tape in other deck will start to play without interruption.

1 Insert tapes into deck 1 and deck 2.

2 Press the TAPE/DECK1/2 button to select the deck to be played back first.

3 Press the REV MODE button to select .

4 Press the button to start playback.

Playback continues until the button is pressed.

About cassette tapes

• To prevent accidental erasure, break off the plastic tabs on the cassette tape after recording with a screwdriver or

other pointed tool.

To record on the tape again, cover the tab openings with adhesive tape, etc. (On Type II tapes, take care not to cover

the Type II tape detection slot.)

• 120-minute or longer tapes are extremely thin and easily deformed or damaged. They are not recommended.

• Take up any slack in the tape with a pencil or similar tool before use. Slack tape may break or jam in the

mechanism.

RECORDING pg. 13

BASIC RECORDING

This section explains how to record from the tuner, CD player, or external equipment.

Preparation

• Set the tape to the point where recording will start.

• Use Type I (normal) and Type II (high/CrO

2

) tapes for recording.

1 Insert the tape to be recorded on into deck 2.

Insert the tape with the side to be recorded on first facing out from the unit.

2 Press the REV MODE button to select the reverse mode.

To record on one side only, select .

to record on both sides, select or .

3 Press one of the function buttons and prepare the source to be recorded.

To record from a CD,

press the CD button and load the disc (s).

To record from a radio broadcast,

press the TUNER button and tune into a station.

To record from the connected source,

press the VIDEO/AUX or MD button and play.

4 Press the

REC/REC MUTE button to start recording.

Page is loading ...

Aiwa CX-NA31 User manual

Aiwa CX-NA31 User manual

Related papers

Other documents