Trane Trane Outdoor Units: Heat Pumps, Air Conditioners User manual

Trane
Brand
Trane
Model
Trane Outdoor Units: Heat Pumps, Air Conditioners
Category
Split-system air conditioners
Type
User manual

This manual is also suitable for

22-5213-WEB01
Owner's Guide
Outdoor Units:
Heat Pumps
Air Conditioners
2 22-5213-WEB01
To prevent injury, death, or property
damage, read and follow all instructions
and warnings, including labels shipped
with or attached to unit before operating
your new outdoor system.
Disconnect all electrical power to the
indoor air handler or furnace before
removing access panels to perform any
maintenance. Disconnect power to both
the indoor and outdoor units. NOTE:
There may be more than one electrical
disconnect switch. Electric shock can
cause personal injury or death.
Although special care has been taken to
minimize sharp edges in the construction
of your unit, be extremely careful when
handling parts or reaching into the unit.
How it works to keep you comfortable
Congratulations on the purchase of your new Trane outdoor unit.
Your outdoor unit is designed to work with a matched indoor unit
creating a system that delivers years of dependable service and
performance.
Your system will cool, filter, and dehumidify the air in your home.
Additionally, a heat pump heats the air in your home.
As the system circulates air, it also filters it. The system also extracts
excess moisture from the home to help control humidity in muggy
summer months.
Acquaint yourself with your new system by spending just a few minutes
with this booklet. Learn about the operation of your system and the small
amount of maintenance it takes to keep it operating at peak efficiency.
An outdoor unit is not a household
appliance. It’s a self‑contained system
that requires professional maintenance
and repair.
That’s why attempts at “do‑it‑yourself”
repairs on an in‑warranty unit may void
the remainder of your warranty.
Other than performing the simple
maintenance recommended in this
manual, you should not attempt to make
any adjustments to your system. Your
dealer will be able to take care of any
questions or problems you may have.
Help ensure top efficiency by cleaning
or replacing the filter monthly.*
When your system circulates and filters
the air in your home, dust and dirt
particles build up on the filter. Excessive
accumulation can block the airflow,
forcing the unit to work harder to maintain
desired temperatures. And the harder
your unit works, the more energy it uses.
Clean or replace your filter twice a month
during seasons when the unit runs more
often.
When replacing your filter(s), always use
the same size and type that was originally
supplied. Filters are available from your
dealer.
Where disposable filters are used, they
must be replaced every month with the
same size as originally supplied.
How to remove your filter.*
Ask your Trane dealer where the filter
is located in your system and how to
service it.
Just be sure to replace it with the arrows
pointing in the direction of the airflow.
* Before removing the filter, see the owner’s manual
furnished with the indoor unit.
Efficiency can be maintained
by keeping the outdoor unit clear
of snow, ice and debris.
Efficient operation of your outdoor unit
depends on the free flow of air over the
coil. Anything that blocks the airflow
causes the compressor to work harder
to move the warm air out of your house.
Buildup of snow and ice can restrict
airflow. As soon as possible after
accumulation, clean snow from the area
around the outdoor unit.
To avoid overworking your unit, do not
plant flowers or shrubbery right next to
it. Also, make sure that nothing is stacked
against the sides of the unit or draped
over it.
Making sure your outdoor unit is kept
clear at all times helps it work at peak
efficiency.
Proper maintenance for maximum efficiency
Heat Pumps
heat in winter.
Air Conditioners
and Heat Pumps
cool in summer.
Air Conditioner & Heat Pump Heat Pump
3 22-5213-WEB01
If heating system is not operational during
the cold weather months, provisions must
be taken to prevent freeze-up of all water
pipes and water receptacles. This is very
important during times of vacancy.
Proper maintenance (continued)
How to operate your system for peak performance
When removing this moisture your system
must work harder than when simply
cooling the air.
That’s why kitchens, bathrooms and
utility rooms should have vents and
exhaust fans. These devices help prevent
accumulation of moisture throughout the
rest of the house so your outdoor unit
works less to keep you comfortable.
Many homeowners have found that
operating their system in continuous fan
mode (thermostat in the “on” position)
offers benefits such as elimination of hot
and cold spots in the home and constant
air filtration. However, continuous fan
mode during cooling operation may not
be appropriate in humid climates. If the
indoor air exceeds 60% relative humidity
or simply feels uncomfortably humid, it is
recommended that the fan only be used
in the AUTO mode.
Setting the temperature.
Place the system switch on COOL, and
the fan switch on AUTO. Then set the
temperature by using the indicator on the
thermostat* control.
Now your system will cool your house
whenever the indoor temperature
climbs above the thermostat setting.
It will shut off when the desired room
temperature is reached.
In winter, it works the same way. When the
system switch is on HEAT, the system will
operate whenever the room temperature
falls below the temperature setting. Once
the desired temperature is reached, the
system will shut off.
Save energy with a
programmable thermostat.*
Program the thermostat for the
temperatures that meet your comfort
level. The Trane programmable thermostat
has up to four setup or setback periods
each day, plus weekend and vacation
programs.
Let the thermostat do its job.
Your system will perform most efficiently
when you let the thermostat control it.
Turning the system on and off manually
is usually much less efficient. So let the
thermostat do its job.
We recommend keeping the temperature
setting at 78°F for cooling, 68°F for
heat ing. However, you can select the
temperature that meets your comfort level.
The point is, once you’ve set the
thermostat, keep subsequent adjustments
to a minimum.
When you’re going to be away from
home for a few days, or when outdoor
temperatures are moderate, don’t let the
outdoor unit run unnecessarily. Lower
the thermostat to 55°F in the winter.
And raise it to 85°F in summer. Then
when you return, or when temperature
conditions dictate, you can reset the
system and it will resume making your
home comfortable again.
How to help reduce summer humidity.
In summer, your outdoor unit does more
than cool the air — it helps remove the
excess moisture that can make the inside
of your home feel muggy.
* Accessory, purchased separately. Carefully read the
accompanying thermostat manual for complete
operating instructions.
Call your dealer for additional
routine maintenance.
Your outdoor unit should be inspected
regularly by a properly trained service
technician.
For regular dealer maintenance please
refer to www.acca.org/industry/quality
Keep your outdoor unit
looking new for years.
Clean the enamel finish of your outdoor
unit with soap and water. For stubborn
grease spots, use a household detergent.
Do not use lacquer thinner or other
synthetic solvents as they may damage
the finish.
4 22-5213-WEB01
Before you call for service, check the following:
Problem Possible cause Remedy
Insufficient heating
or cooling
a. dirty filters
b. air not circulating freely
c. blocked outdoor coil
a. clean or replace
b. check supply registers and return
grills for blockage
c. clear away leaves or other debris
Failure to operate a. power off
b. open circuit breaker or
burned‑out fuses
c. improperly adjusted
thermostat
a. make sure main switch is in
ON position
b. reset circuit breaker, or replace
burned‑out fuses
c. check setting, adjust thermostat
Blue auxiliary heat
light on
When outdoor temperature falls,
intermittent lighting is normal.
Monitor light. If it stays on continuously
when above 30°F, or if it comes on
when 50°F outdoors, call for service.
No heating or
cooling – Blower
does not operate
Blower door removed or ajar Close door securely to restore power
to blower
Unusual noise Call your local servicer
The Problem Solver
Extra Energy Tips
Insulation
1. Make sure your home is properly
insulated. This is the single most
important step in conserving
energy. Thermal insulation should
be specified in terms of thermal
resistance (R-values). R-30 (10")
is recommended for ceilings,
R-11 (3-1/2") for exterior walls
and floors over unheated areas. In
colder climates, consider additional
insulation.
2. Infiltration of humid outside air is
your heating and cooling system’s
worst enemy — it could account for
15 to 30% of air conditioning energy
requirements. Find the places where
air can sneak into the home and
plug them with caulking, weather-
stripping or plastic. Also, weather-
strip and caulk around all entrance
doors and windows.
3. Cut heat transfer through your
windows by 40 to 50% with
double glazing (two panes of glass
separated by a sealed air space) and
low-e glass.
4. Use wood- or metal-frame storm
windows even if single-glazed
windows are high quality. The extra
layer of glass and the layer of still air
will cut heat transfer considerably.
5. Install storm doors at all entrances
to your house.
6. Keep all windows and doors closed.
7. Remember that by increasing the
glass area, you increase the amount
of heat added in summer and lost in
winter.
8. Make sure fireplaces have
tight-fitting dampers which can be
closed when the fireplace is not in
use.
9. Invest in a humidifier to conserve
energy in winter. The air in your
home won’t be as dry, so you stay
comfortable at a lower temperature
setting.
Heating
10. Locate the thermostat on an inside
wall away from windows and doors.
11. Set the thermostat as low as comfort
permits. Each degree over 68°F can
add 3% to the amount of energy
needed for heating.
12. People generate heat. So lower the
thermostat a degree or two when
expecting a large group of guests.
Cooling
13. Set the thermostat as high as
comfort will permit.
14. Make sure attics are adequately
ventilated to relieve heat buildup.
If necessary, improve airflow by
adding or enlarging vents.
15. When building a new house or
renovating an old one, choose
light-colored roof shingles to reflect
more of the sun’s heat.
16. During moderate weather, don’t use
the system unnecessarily.
17. Draw blinds or drapes to block the
sunlight during the hottest part of
the day.
18. Install awnings over windows
exposed to direct sunlight.
19. In the cooling season, don’t run
kitchen and bath exhaust fans
longer than necessary.
20. Don’t place lamps, TV sets or other
heat producing devices beneath a
wall-mounted thermostat. Rising
heat from the equipment may cause
the system to over-cool your house.
Reduce the burden of
unexpected repair bills with
a Trane Extended Warranty.
Trane offers the finest quality products
and manufacturer’s warranties on the
market. But, like all good things, the
Trane-provided limited warranty on your
new comfort equipment will come to an
end. To keep you protected, Trane offers
the Extended Warranty Program. It picks
up right where your Trane limited warranty
leaves off. And, it offers years and years of
reliable protection at a low cost. Ask your
dealer for program details.
Subject to the terms and conditions of this limited warranty, Trane U.S., Inc. (“Company’) extends
a limited warranty against manufacturing defects for the product(s) identied in Table 1 attached hereto
(“Products’) that are installed in a residential application (personal, family or household purposes) under
normal use and maintenance in the United States and Canada.
This limited warranty applies to Products manufactured on or after August 1, 2011.
In order to maximize the available benets under this limited warranty, the Purchaser (as dened
below) should read it in its entirety. All repairs of Product parts covered under this limited warranty must
be made with authorized service parts and by a licensed HVAC service provider. Additionally, commercial
applications are treated differently under this limited warranty as stated in Table 1 attached hereto. For
purposes of this limited warranty, “commercial applications” shall mean any application other than for
personal, family, or household use.
TERM: The limited warranty period for Products is as stated in Table 1 attached hereto. If the Pur-
chaser properly registers the Products, the limited warranty period shall be extended as stated in Table 1
attached hereto. Regardless of registration, the Commencement Date for a limited warranty period shall
be the date that the original installation is complete and all Product start-up procedures have been prop-
erly completed and veried by an installer’s invoice. If the installation and start-up date cannot be veried
by the installer’s invoice, the Commencement Date shall be sixty (60) days after the factory manufacture
date which is veried by the Product serial number. Where a Product is installed in a newly constructed
home, the Commencement Date is the date the Purchaser purchased the residence from the builder.
Proof of Product purchase, installation, and/or closing date of the residence may be required to conrm
the Commencement Date.
The installation of Product replacement parts under this limited warranty shall not extend the original
warranty period. The warranty period for any Product part replaced under this limited warranty is the ap-
plicable warranty period remaining under the original Product warranty.
WHO IS COVERED: This limited warranty is provided only to the original owner and his or her
spouse (“Purchaser’) of the residence where the Products are originally installed. This warranty is not
transferable except according to terms stated on the applicable website identied below under Registra-
tion Requirements. Company has the right to request any and all proof of Product purchase or installation
and/or closing date of the residence.
WHAT COMPANY WILL DO: Company may request proof of Product purchase and/or installa-
tion in order to provide Product parts under this limited warranty. As Company’s only responsibility and
Purchaser’s only remedy under this limited warranty, Company will furnish a replacement part to the
licensed HVAC service provider, without charge for the part only, to replace any Product part that fails
due to a manufacturing defect under normal use and maintenance. The Purchaser must pay for any
and all shipping and handling charges and other costs of warranty service for the replacement part. If a
Product part is not available, Company will, at its option, provide a free suitable substitute part or provide
a credit in the amount of the then factory selling price for a new suitable substitute part to be used by the
Purchaser towards the retail purchase price of a new Company product. Any new Product purchase shall
be at Purchaser’s sole cost and expense including, but not limited to, all shipping, removal, and installa-
tion costs and expenses.
REGISTRATION REQUIREMENTS: All Products must be properly registered online by the Pur-
chaser within sixty (60) days after the Commencement Date to receive the registered limited warranty
terms. To register online, go to:
http://www.trane.com/Residential/Trane/Owners/Warranty-Information or
http://www.americanstandardair.com/sevicesupport/pages/warranty.aspx
and click “Begin Online Registration.” If a Purchaser does not register within this stated time period,
the base limited warranty terms shall apply.
ELIGIBILITY REQUIREMENTS: The following items are required in order for the Products to be
covered under this limited warranty:
• The Products must be in the same location where they were originally installed.
• The Products must be properly installed, operated, and maintained by a licensed HVAC service
provider in accordance with the Product specications or installation, operation, and maintenance
instructions provided by Company with each Product. Failure to conform to such specications and/
or instructions shall void this limited warranty. Company may request written documentation show-
ing the proper preventative maintenance.
• All Product parts replaced by Company under this limited warranty must be given to the servicing
provider for return to Company.
• Air handlers, air conditioners, heat pumps, cased or uncased coils and stand-alone furnaces must
be part of an Air Conditioning, Heating, and Refrigeration Institute rated and matched system or a
specication in a Company provided bulletin or otherwise approved in writing by a Company autho-
rized representative.
EXCLUSIONS: The following are not covered by this limited warranty:
• Labor costs including, but not limited to, costs for diagnostic calls or the removal and reinstallation of
Products and/or Product parts.
• Shipping and freight expenses required to ship Product replacement parts.
• Failures, defects, or damage (including, but not limited to, any loss of data or property) caused by (1)
any third party product, service, or system connected or used in conjunction with the Products; (2)
any use that is not designed or intended for the Products; (3) modication, alteration, abuse, misuse,
negligence, or accident; (4) improper storage, installation, maintenance, or operation including, but
not limited to, operation of electrical equipment at voltages other than the range specied on the
Product nameplate; (5) any use in violation of written instructions or specications provided by Com-
pany; (6) any acts of God including, but not limited to, re, water, storms, lightning, or earthquakes;
or any theft or riots; or (7) a corrosive atmosphere or contact with corrosive materials such as, but
not limited to, chlorine, uorine, salt (provided that indoor and outdoor coils will only be covered if
a Sea Coast Kit is installed), sulfur, recycled waste water, urine, fertilizers, rust, or other damaging
substances or chemicals.
• Products purchased direct including, but not limited to, Internet or auction purchases and purchases
made on an uninstalled basis.
• 3 phase models, cabinets or cabinet pieces that do not affect product performance, air lters, refrig-
erant, refrigerant line sets, belts, wiring, fuses, surge protection devices, non-factory installed driers,
and Product accessories.
• Increased utility usage costs.
REFRIGERANT POLICY: Beginning on January 1, 2010, R-22 refrigerant will no longer be used
as a manufacturer-installed refrigerant as required by federal regulation. Any and all expenses or costs
associated with replacing Product parts that are not R-410A compatible will not be covered by the terms
and conditions of this limited warranty. In addition, all Products containing R-410A refrigerant include a
liquid line lter drier which must be replaced when a compressor replacement is necessary. A suction line
lter drier must be added for compressors dened as burnouts. Failure to comply with such lter drier
requirements or the use of contaminated or alternate refrigerant or any non-approved refrigerant system
additives including, but not limited to, dyes, will void this limited warranty.
ADDITIONAL TERMS:
THIS LIMITED WARRANTY AND LIABILITY SET FORTH HEREIN ARE IN LIEU OF ALL OTHER
WARRANTIES AND LIABILITIES, WHETHER IN CONTRACT OR IN NEGLIGENCE, EXPRESS OR
IMPLIED, IN LAW OR IN FACT. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE LIMITED TO THE DURATION OF THE APPLICABLE PRODUCT
WARRANTY. COMPANY DOES NOT AUTHORIZE ANY PERSON TO CREATE FOR IT ANY OBLIGA-
TION OR LIABILITY IN CONNECTION WITH THE PRODUCTS.
NOTWITHSTANDING ANYTHING IN THIS LIMITED WARRANTY TO THE CONTRARY, COMPANY
SHALL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL AND/OR
PUNITIVE DAMAGES, WHETHER BASED ON CONTRACT, WARRANTY, TORT (INCLUDING, BUT
NOT LIMITED TO, STRICT LIABILITY OR NEGLIGENCE), PATENT INFRINGEMENT, OR OTHER-
WISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. COMPANY’S MAXIMUM
LIABILITY HEREUNDER IS LIMITED TO THE ORIGINAL PURCHASE PRICE OF THE PRODUCTS.
No action arising out of any claimed breach of this limited warranty may be brought by a Purchaser
more than one (1) year after the cause of action has arisen.
This limited warranty gives you specic legal rights, and you may also have other rights as otherwise
permitted by law. If this Product is considered a consumer product, please be advised that some local
laws do not allow limitations on incidental or consequential damages, how long a warranty lasts based on
registration, or how long an implied warranty lasts, so that the above limitations may not fully apply. Refer
to your local laws for your specic rights under this limited warranty.
Residential Systems
6200 Troup Highway, Tyler, TX 75707
Attn: Customer Relations
Or visit our website at www.trane.com or www.americanstandardair.com
GW-654-3111
Limited Warranty Information
www.trane.com
Ingersoll Rand Residential Solutions, a business comprised of well-known brands like Schlage and Trane, delivers
safety, comfort and efficiency to homeowners throughout North America. Our quality products, services and
solutions include mechanical and electronic locks, heating and air conditioning systems, indoor air quality
solutions, advanced controls, portable security systems and remote home management. For more information on
these and other residential solutions please visit www.ingersollrand.com, www.schlage.com, or www.trane.com.
Important Product Information
Thank you for purchasing Trane home comfort products. Registering your products helps us provide you with one of the strongest
manufacturer limited warranties available. Product registration can be completed either online at Trane.com or by calling
800‑554‑6413. You will need the serial number, model number, and installation date for each product being registered. Your dealer
may have included these on your invoice or can provide a list for you to use. Please take a few moments to record the following
information to ensure your product registration process is quick and easy:
Outdoor Unit Serial Number _______________________________________________________________________________________
Outdoor Unit Model Number ______________________________________________________________________________________
Thermostat Model Number ________________________________________________________________________________________
Date of Installation _______________________________________________________________________________________________
Dealer __________________________________________________________________________________________________________
Service Information
Call your installing dealer if the unit is inoperative. Before you call, always check the following to be sure service is required:
a. Be sure the main switch that supplies power to the unit is in the ON position.
b. Replace any burned‑out fuses or reset circuit breakers.
c. Be sure the thermostat is properly set.
Service Phone ___________________________________________________________________________________________________
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Trane Trane Outdoor Units: Heat Pumps, Air Conditioners User manual

Trane
Brand
Trane
Model
Trane Outdoor Units: Heat Pumps, Air Conditioners
Category
Split-system air conditioners
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents