KitchenAid KGYS677EZ0 Owner's manual

Brand: KitchenAid

Model: KGYS677EZ0

Category: Washer dryers

Type: Owner's manual

Models

KEYS677E, KGYS677E

KEYS777E, KGYS777E

PART NO. 3405630 Rev,A

Thank you for buying a KITCHENAID ®appliance!

KitchenAid designs the best tools for the most important room in your house. To ensure that you enjoy many

years of trouble-free operation, we developed this Use and Care Guide. It contains valuable information

concerning how to operate and maintain your new appliance properly and safely. Please read it carefully.

Also, please complete and mail the enclosed Product Registration Card.

For assistance or service

Call the Consumer Assistance Center toll free ...................................................................... 1-800-422-1230

If you need assistance or service, first see the "Troubleshooting" section of this book. After checking

"Troubleshooting," additional help can be found by checking the "Requesting Assistance or Service"

section, or by calling the telephone number above.

When calling, you will need to know your appliance's complete model number and serial number. You can

find this information on the model and serial number label (see diagram on page 5).

Keep this book and the sales slip together in a safe place for future reference. You must provide proof

of purchase or installation date for in-warranty service.

Model Number

Serial Number

Date Installed

Builder/Dealer Name

Address

Phone

Your safety is important to us.

This guide contains safety symbols and statements.

Please pay special attention to these symbols and

follow any instructions given. Here is a brief explan-

ation of the use of the symbol.

This symbol alerts you to hazards

such as fire, electrical shock, or

other injuries.

WARNING: For your safety, the information in this manual must be followed to

minimize the risk of fire or explosion, or to prevent property damage, personal injury,

or loss of life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity

of this or any other appliance.

= WHAT TO DO iF YOU SMELL GAS:

o Do not try to light any appliance.

o Do not touch any electrical switch; do not use any phone in your building.

o Clear the room, building, or area of all occupants.

o immediately call your gas supplier from a neighbor's phone.

Follow the gas supplier's instructions.

o if you cannot reach your gas supplier, call the fire department.

- installation and service must be performed by a qualified installer, service agency,

or the gas supplier.

continued on next page

iMPORTANT SAFETY iNSTRUCTiONS

WARNING - To reduce the risk of fire, electric shock, or injury to persons when using the

dryer, follow basic precautions, including the following:

-,Read all instructions before using

the dryer.

-,Do not dry articles that have been previ-

ously cleaned in, washed in, soaked in,

or spotted with gasoline, dry-cleaning

solvents, other flammable, or explosive

substances as they give off vapors that

could ignite or explode.

-,Do not allow children to play on or in

the dryer. Close supervision of children

is necessary when the dryer is used

near children.

-,Before the dryer is removed from service

or discarded, remove the door to the

drying compartment.

-,Do not reach into the dryer if the drum

is moving.

-,Do not install or store the dryer where

it will be exposed to the weather.

-,Do not tamper with controls.

-,Do not repair or replace any part of the

dryer or attempt any servicing unless

specifically recommended in this Use and

Care Guide or in published user-repair

instructions that you understand and have

the skills to carry out.

-,Do not use fabric softeners or products to

eliminate static unless recommended by

the manufacturer of the fabric softener or

product.

-,Do not use heat to dry articles containing

foam rubber or similarly textured rubber-

like materials.

-,Clean lint screen before or after each load.

-,Keep area around the exhaust opening

and adjacent surrounding areas free from

the accumulation of lint, dust, and dirt.

-,The interior of the dryer and exhaust duct

should be cleaned periodically by qualified

service personnel.

-,See Installation Instructions for grounding

requirements.

- SAVE THESE INSTRUCTIONS -

The parts and features of your dryer are illustrated on this page. Become familiar with all parts and

features before using your dryer. Page references are included next to some features. Refer to those

pages for more information about the features.

NOTE: The drawings in this book may vary from your dryer model. They are designed to show the

different features of all models covered by this book. Your model may not include all features.

Cycle control

knob

(pp. 8-12)

SELECTRA TM

controls

Start button

(p. 9)

Lint screen

(p. 14)

Model and

serial number

(p. 2)

Exhaust grill

Drum light /

(p. 16)

Dryer

(p. 15)

Electronic

dryness

sensor

(p. 10)

Wide=opening

hamperdoor

Additional feature on models

KEYS777E and KGYS777E:

ULTRA LOW temperature setting

(on model KEYS777E)

EXTRA LOW temperature setting

(on model KGYS777E)

Your dryer must be properly installed and vented to achieve maximum drying efficiency and shorten

drying times. Install your dryer in a well-ventilated room where the temperature is always above

45°F (7°C). Also make sure that your dryer is leveled. Refer to your installation instructions for more

information.

Venting

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent.

Do not use a metal foil vent.

Failure to follow these instructions can result

in death or fire.

If the dryer is not properly installed and vented, it

will not be covered under the warranty.

NOTE: Service calls caused by improper venting

will be paid for by the customer, whether it was a

paid installation or self-installed. For paid installa-

tion, call the company that installed the vent for

adjustment.

1. Four-inch heavy metal or flexible metal vent must

be used. Do not use

plastic vent or flexible

metal foil vent. Do not

kink or crush flexible

metal vent. It must be

completely extended to

allow adequate exhaust

air to flow. Check vent

after installation. Refer

to your Installation

Instructions for proper

length requirements of vent.

2. Use a 4" exhaust hood. Smaller hoods increase

drying times.

3. The exhaust vent can be routed up, down, left,

right, or straight out the

back of the dryer. Space

requirements are listed

in your Installation

Instructions.

Venting (cont.)

4. Use the straightest path 3ossible when routing the

exhaust vent. Avoid 90°

turns, if possible. Allow

room when using

elbows or making turns.

Bend vent gradually to

avoid kinking.

5. Use duct tape to seal all joints. Do not use screws

to secure vent. Lint may

catch on screws.

6. Clean exhaust vent periodically, depending on use,

but at least every 2 years,

or when installing your

dryer in a new location.

• Disconnect vent from

the dryer and clean one

section at a time until

you reach the exhaust

hood.

• Use the hose attach-

ment on your vacuum,

or a pole or wire with a

feather duster or rag attached, to clean out lint.

Be sure the flapper on the outside end of vent

moves freely.

When cleaning is complete, be sure to follow the

Installation Instructions supplied with your dryer

for final product check.

To get the best dryer results possible, you must use your dryer correctly. This section tells you how to

use your dryer properly and efficiently.

Starting your dryer

Explosion Hazard

Never place items in the dryer that are

dampened with gasoline or other

flammable fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any

type of oil on it (including cooking oils).

Doing so can result in death, explosion,

or fire.

Before using your dryer, wipe the dryer drum with a

damp cloth to remove dust from storing and shipping.

If your dryer has a Consumer Buy Guide, remove it

and place it with this Use and Care Guide.

1. Load clothes loosely into the dryer and close the

door. Do not pack the

dryer; allow space for

clothes to tumble freely.

3. Set the Temperature selector to the recommended

setting for the type of

fabric being dried.

m The cycle descriptions

on pages 10-12 include

temperature setting

suggestions.

4. (OPTIONAL STEP) Set the Cycle Signal selector to

m D

L L:

On if you want the dryer

to sound a signal when a

cycle is finished. The

signal is helpful when you

are drying permanent

press, synthetics, and

other items that should

be removed from the

dryer as soon as it stops.

5. (OPTIONAL STEP) Your

m D

dryer has an Extra Care

feature to protect your

clothing from wrinkling

once the dryer stops.

• On models KEYS777E

and KGYS777E, set the

Extra Care selector to Off

if you want the dryer to

stop after cool-down.

(See page 10.)

2. Turn the Cycle Control Knob to the recommended

cycle for the type of load

being dried, as de-

scribed on pages 10-12.

Use the Energy

Preferred Automatic

Setting (2)in the Regu-

lar/Heavy cycle to dry

most heavyweight and

mediumweight loads.

Starting your dryer (cont.)

6. Push the Start Button.

NOTE: Your dryer stops automatically when a

cycle ends.

Stopping and restarting your dryer

You can stop your dryer anytime during a cycle.

To stop your dryer:

Open the dryer door or turn the Cycle Control Knob

to Off.

NOTE: The Cycle Control Knob should point to an

Off area when the dryer is not in use.

To restart your dryer:

Close the door, select a new cycle and temperature

(if desired), and push the Start Button.

Selecting the right cycle and temperature setting

The following pages describe the drying cycles

on your dryer. The descriptions include suggested

temperature settings and drying times for various

loads.

Cycle and temperature tips

• Models KEYS777E and KGYS777E have a special

Ultra Low temperature setting that reduces drying

temperatures, providing enhanced fabric care for

delicates and other fine fabrics.

• In both Automatic cycles (Regular/Heavy and

Permanent Press), the FLO-THRU TM Drying

System automatically reduces the heat near

the end of the cycles to prevent overdrying.

• If some types of loads in the cycle descriptions

have more than one suggested temperature

setting, choose the lowest setting available on

your dryer.

• The last few minutes of all cycles are without heat

to make the load cooler to handle.

Drying tips

• Make sure you have selected the correct cycle

and temperature for your load. For example, use

the Towels feature for best drying results with

extra heavy items.

• Always follow care label directions when they are

available.

• Always use fabric softener sheets labeled as

dryer safe and follow package instructions

carefully.

• Remove the load from the dryer as soon as

tumbling stops to reduce wrinkling. This is

especially important for permanent press, knits,

and synthetic fabrics.

Automatic cycles

Your dryer has 2 Automatic cycles: Regular/Heavy

and Permanent Press. Both Automatic cycles use

an electronic dryness sensor control that senses the

amount of moisture in the load and shuts off the

dryer when the selected dryness is reached.

The Cycle Control Knob does not move until the

load is almost dry. After the cool-down, the Knob

automatically turns to an Off area and tumbling

stops.

• Dry most loads using the Energy Preferred Auto-

matic Setting (2) in the Regular/Heavy cycle.

For any Automatic setting, you can choose any

temperature setting you want. Suggested tempera-

ture settings are listed below.

• If the load is drier than you like, select a setting

closer to Less Dry the next time you dry a

similar load.

• If the load is not as dry as you like, complete drying

using the Timed Dry cycle (see next page). Select a

setting closer to Very Dry the next time you dry a

similar load.

The Extra Care feature protects your clothing from

wrinkles if you are unable to unload the dryer within

5 minutes after tumbling stops. The Extra Care

feature tumbles the load without heat every few

minutes up to 40 minutes after the cycle ends.

On models KEYS777E and KGYS777E, you can

set the Extra Care feature On or Off (see page 8).

If the SELECTRA TM button is set to Off, the Perma-

nent Press cycle ends after cool-down.

• A signal sounds every few minutes when Extra

Care is running. The signal and cycle stop when

you open the dryer door.

Use the Regular/Heavy Automatic cycle for

heavyweight and

mediumweight cotton

VERYDR¥ items, such as towels,

linens, bedspreads,

work clothes, blue

jeans, and corduroys.

Set your Temperature

selector to Hi or Med

Hi heat.

Use the Towels feature

when you have large

loads of thick towels to dry. This setting allows for

more drying time and can also be used for extra

heavy items such as mattress pads and quilts.

Use the Permanent Press Automatic cycle for

heavyweight and

mediumweight perma-

nent press items, knits,

and other synthetic

fabrics.

Set your Temperature

selector to Hi, Med,

or Low heat.

EXTRA CARE

Timed Dry cycles

Use the Timed Dry cycle to complete drying if some

items are damp after

Automatic drying. The

Timed Dry cycle is also

useful for:

• Heavyweight and

bulky items, such as

bedspreads and work

clothes, and large

loads that require a

long drying time. Set

your Temperature

selector to Hi and the Cycle Control Knob for

50 to 70 minutes.

Lightweight items, such as lingerie, blouses, and

knits that require a short drying time. Set your

Temperature selector to Low, Med Low, or Ultra

Low, and the Cycle Control Knob for 20

to 30 minutes.

Models KEYS777E and KGYS777E have an Extra

Dry feature to dry large items or items that are

thicker or heavier than a regular load. Set your

Temperature selector to HI for this feature.

Use the Ironing Damp feature to dry items to damp

level or to dry items that do not require an entire

drying cycle. Examples are heavy cottons, such as

jeans, which you do not want to become stiff, or

cotton clothes that are easier to press when damp.

Set your Temperature selector to Hi.

The Quick Press feature removes wrinkles from

clothes that have been packed in a suitcase or

closet, or from items not removed from the dryer at

the end of a cycle. As soon as the dryer stops, fold

or put the items on hangers. Set your Temperature

selector to Med Hi or Med Low.

Models KEYS777E and KGYS777E have a Rack

Dry feature to dry items without tumbling them.

See page 13.

AirTumble cycle

Use the unheated Air Tumble cycle for items that

require drying without

heat. Since this cycle

has no heat, the Tem-

perature selector setting

will have no effect. The

following chart includes

examples of items that

require drying without

heat. Use the Air

Tumble cycle or place

the items on a line or

rack to air dry.

• Line dry bonded or laminated fabrics.

Always follow care label directions when they are

available.

Fire Hazard

Use Air Tumble cycle or line dry items

listed below.

Do not use heat to dry these items.

Failure to follow these instructions can

result in death or fire.

TYPE OF LOAD AIR TUMBLE CYCLE*

(minutes)

RUBBER, PLASTIC, HEAT-SENSITIVE FABRICS

Foam Rubber- Pillows, padded bras, stuffed toys

Make sure coverings are securely stitched.

• Shake and fluff pillows by hand several times during the Air

Tumble cycle.

Make sure pillows are completely dry. Foam rubber pillows

take a long time to dry.

Plastic - Shower curtains, tablecloths

Rubber-backed rugs

Olefin, Polypropylene, Sheer nylon

20-30

40-50

10-20

* Reset cycle as needed to complete drying.

Using the drying rack

Models KEYS777E and KGYS777E include a drying

rack. On models KEYS677E and KGYS677E, you

can order a drying rack by calling 1-800-422-1230,

from anywhere in the U.S.A. You will hear a record-

ing. Follow the instructions to place an order.

The drying rack lets you dry items without tumbling

them. The rack does not move, but the drum turns.

. Fit rear legs of the rack into spaces in the back

wall of the dryer. Lower

the front so the legs rest

L_..._ ____ °n the dryer °pening

! ! ',

2. Put wet items on top of the rack. Leave space

between the items

so air can reach all

surfaces.

• See chart below for

suggested cycles and

settings for items that

might best be rack

dried. Drying time will

depend on amount of

moisture items hold.

3. Close the door.

4. Select the Timed Dry cycle and temperature, or

the Air Tumble cycle.

& Push the Start Button.

NOTE: Make sure nothing hangs over the edge of

the rack.

NOTE: The rack must be removed for normal

tumbling. Automatic cycles do not work with the

drying rack.

RACK DRY CYCLE TEMPERATURE TIME*

(minutes)

Wool sweaters Timed Dry Low 60

(Block to shape and lay flat on the rack)

Stuffed toys or pillows Timed Dry Low 60

(Cotton or polyester fiber filled)

Stuffed toys or pillows Air Tumble None; cycle is unheated. 90

(Foam rubber filled)

Sneakers or canvas shoes Air Tumble None; cycle is unheated. 30-40

*Reset cycle as needed to complete drying.

Proper care of your dryer can extend its life and help your dryer operate efficiently.

Cleaning the lint screen

Every load cleaning

The lint screen is located under a lid on top of the

dryer. Clean it before each load. A screen blocked

by lint can increase drying time.

To clean:

1. Open the lid and pull the lint screen towards you.

2. Roll lint off the screen with your fingers. Do not

i inse or wash screen to

remove lint. Wet lint is

hard to remove.

As needed cleaning

Laundry detergents and fabric softeners can cause

a residue buildup on the lint screen. This buildup

can cause longer drying times for your clothes, or

cause the dryer to stop before your load is com-

pletely dry. You may be able to see this buildup, or

the lint may be falling off the screen because it is

clogged.

Clean the lint screen with a nylon brush every six

months or more frequently if it becomes clogged

due to a residue buildup.

Use the following method:

1. Wet both sides of lint screen with hot water.

2. Wet a nylon brush with hot water and liquid

detergent; scrub lint

screen with the brush to

remove residue buildup.

3. Push the lint screen firmly back into place and

close the lid.

IMPORTANT:

• Do not run the dryer with the lint screen loose,

damaged, blocked, or missing. Doing so can

cause overheating and damage to both the dryer

and fabrics.

• Some towels made of synthetic fibers and natural

fibers (polyester and cotton blends) may shed

more lint than other towels, causing your dryer's

lint screen to fill up faster. Be sure to remove lint

from the lint screen before and after drying new

towels.

3. Rinse screen with hot water.

4. Thoroughly dry lint screen with a clean towel;

replace in dryer.

Lint signal

The lint signal (a whistle tone) indicates excessive

lint is present on your lint screen or it

has a residue buildup. See page 14.

A full lint screen restricts airflow and

reduces drying efficiency. When you

hear the signal, stop the dryer and

clean the lint screen.

NOTE: Clean your lint screen before each load. Do

not wait for the lint signal.

(::leaning the dryer interior

Garments which contain unstable dyes, such as

denim blue jeans or brightly colored cotton items,

may discolor the dryer interior. These stains are not

harmful to your dryer and will not stain future loads

of clothes. It is helpful to dry unstable dye items

inside out to prevent dye transfer.

To clean dryer drum:

1. Make a paste with powdered laundry detergent

and very warm water.

2. Apply paste to a soft cloth.

Apply a liquid, non-flammable household cleaner to

the stained area and rub with a soft

cloth until all excess dye is removed.

Explosion Hazard

Use nonflammable cleaner.

Failure to do so can result in death,

explosion, or fire.

3. Wipe drum thoroughly with a damp cloth.

4. Tumble a load of clean cloths or towels to dry drum.

Changing the drum light

Your dryer's drum light may be one of 2 types, as

shown. The dryer light automatically turns on inside

the dryer drum when you open the door.

Fire Hazard

Replace light bulb cover before

operating dryer.

Failure to do so can result in death or fire.

To change drum light type ! :

1. Unplug the dryer or disconnect the electricity

leading to the dryer at the main power supply.

2. Open the dryer door. Remove the light bulb cover

from the back wall

dryer by turning

of the

the cover clockwise.

To change drum light type 2:

1. Unplug the dryer or disconnect the electricity

leading to the dryer at the main power supply.

2. Open the dryer door. Remove the light bulb cover

from the back wall of the

dryer by removing the

screw located in the

lower right corner of

the cover.

3. Remove the light bulb by turning it

counterclockwise.

4. Replace the bulb with a 40-watt appliance

bulb only.

5. Replace the light bulb cover and lock in place

by turning counter-

clockwise.

3. Remove the light bulb by turning it

counterclockwise.

4. Replace the bulb with a 10-watt appliance

bulb only.

5. Replace the light bulb cover.

6. Reconnect power supply. 6. Reconnect power supply.

Removing accumulated

the dryer cabinet

lint from inside

Lint can gather inside the dryer and be a fuel

for fire. Lint should be removed every two to

three years, or more often, depending on dryer

usage. Cleaning should be done by a qualified

person. If you have any questions or comments,

please call our Consumer Assistance Center at

1-800-422-1230 from anywhere in the U.S.A.

Electrical Shock Hazard

Disconnect power before cleaning.

Replace all panels before operating.

Failure to do so can result in death or

electrical shock.

1. Unplug dryer or turn off power supply.

2. Remove rear panel.

3. Remove any lint using a vacuum cleaner or soft

brush. Avoid damaging wires and thermostats.

4. Replace rear panel.

Thermostats

Heater box

Dryer with rear panel removed

5. Open lint screen lid. Remove 2 screws from

lint screen area.

6. Open top by pulling forward and up at each front

corner (see illustration). Rest raised top against

wall behind dryer (top is hinged at rear).

continued on next page

Removing accumulated

the dryer cabinet (co.t.)

7. Remove 2 internal screws from front panel

flanges (near top front corners). Lift front panel

slightly, lifting off lower clips (see lower clip inset

of illustration below). Slowly pull front panel

forward, disengaging panel from drum. (Drum

will drop slightly.)

8. Move front panel aside and rest edge against

side of dryer. Avoid disconnecting wire clips

(see wire clips inset of illustration below) or

damaging wires.

9. Remove any lint using a vacuum cleaner or soft

brush.

lint from inside

Burner Motor

(gas models only)

Dryer with front panel removed

10. Reassemble in reverse order. Before closing the

top, check the following:

- Drum seal must be flared out (see drum seal

insets of illustration) and properly positioned

against panel at back of drum. Rotate drum

counterclockwise one full turn to check

drum seal.

- Belt should be centered and tight on dryer

drum.

- Wire clip retainer, which holds the door switch

wires, must be secured to top of front panel

(see wire clips inset of illustration) and along

top edge of side panel. Door wires must not

touch drum when dryer is operating.

11. Replace top panel and lint screen screws. Top

and front panels must be securely in place

before operating dryer.

12. Level the dryer if necessary.

13. Plug in dryer or turn on power supply.

Most laundering problems are easily solved if you understand the cause. Check the following list for

common laundry problems and the next page for common dryer problems. If you need further

assistance, see "Requesting Assistance or Service" on page 21.

NOTE: In the following list, the most common laundry problems are listed first.

Common laundry problems

Problem ... Cause ...

Slow drying or clothes still wet •

Lint

Static electricity

Wrinkling

Shrinking

Greasy spots/stains

Color change

Garment damage

Incorrect cycle or temperature setting selected.

Full or clogged lint screen. (See page 14.)

Exhaust vent clogged, restricted, or too long. (See pages 6-7 and

Installation Instructions.)

• Dryer not level to allow for clothes contacting the electronic

dryness sensor. (See page 10.)

Dryer located in room with temperature below 45 ° (7°C).

Load too large and bulky to dry quickly.

Drying heavy fabrics (denim, towels) with light fabrics (synthetics,

permanent press).

Fabric softener sheet blocking exhaust grill inside dryer drum.

Full lint screen. (See page 14.)

Load not properly sorted.

Overdrying, especially synthetic fabrics that cause lint-attracting

static electricity.

Load size too big or heavy.

Tissue or paper left in pockets.

Pilling (surface fuzz caused by normal wear and laundering)

attracts lint.

Overdrying.

Dryer fabric softener improperly used. See package directions.

Load includes synthetics, synthetic blends, permanent press, and

knit fabrics that build up static electricity.

Overloading.

Overdrying, especially permanent press and synthetic fabrics.

Large items bailing or rolling up.

Clothes left in dryer at end of cycle.

Overdrying.

Fabric or garment is not designed for tumble drying.

Dryer settings incorrect for fabric type.

Care label instructions not followed.

Dryer fabric softener improperly used. Do not add to a warm load.

Drying soiled items.

Drying dark colors with light colors.

Drying colorfast colors with non-colorfast colors.

Zippers, snaps, and hooks left open.

Strings and sashes not tied to prevent tangling.

Care label instructions not followed.

Common dryer problems

i. Dryer wiii not start.

Is the dryer door firmly closed?

3. No heat

For gas dryers, is the valve open on the

supply line? Also, some dryers may

have an internal gas valve.

Are the controls set in a ON position?

Did you firmly push the Start Button?

Is the power cord plugged in?

Have you blown a fuse or tripped the

circuit breaker? Electric dryers use

2 household fuses or breakers.

2. Lint accumulation in hood or exhaust

vent, or extended drying times,

ls lint screen full?

For electric dryers, have you blown a

fuse or tripped a circuit breaker?

Electric dryers use 2 household fuses

(or breakers). The drum may be turning

but you may not have heat.

4. Noises

Does lint screen need to be cleaned

(lint alert)?

If the dryer hasn't been used forawhile,

there may be a thumping sound during

the first few minutes of operation.

If noises continue, call the Consumer Assistance

Center.

5. Odor

When operating a new dryer, the new

electric heating element may have an

odor.

Are household chemical odors being

drawn into dryer? Proper ventilation

must be used if painting or staining near the dryer.

NOTE: Store and use paints, varnishes, etc. away

from your dryer whenever possible.

If you still have problems, see "Requesting Assist-

ance or Service" on page 21.

Is exhaust vent or outside exhaust

hood clogged with lint? Refer to

venting section on pages 6-7.

Page is loading ...

KitchenAid KGYS677EZ0 Owner's manual

Brand: KitchenAid

Model: KGYS677EZ0

Category: Washer dryers

Type: Owner's manual

Download PDF

report

KitchenAid KGYS677EZ0 Owner's manual

KitchenAid KGYS677EZ0 Owner's manual

Related papers

Other documents