GE AEQ10AMG1 Owner's manual

Brand: GE

Model: AEQ10AMG1

Type: Owner's manual

This manual is also suitable for

ge.com

Safety Instructions . .......... 2, 3

Operating Instructions ........ 4, 5

Care and Cleaning

Air Filter ...................... 6

Outdoor Coils .................. 6

Installation Instructions ..... 7-12

Troubleshooting Tips ......... 14

Normal Operating Sounds ...... 14

Consumer Support

Consumer Support ..... Back Cover

Ownership Registration for

Customers in Canada only ...15, 16

Warranty for Customers

in Canada .................... 17

Warranty for Customers

in the U.S.A ................... 18

AEMIO*

AEM12 *

A_:Q1o

A_:Q12

Climadseur

La section fran(aise commence ?_la page 19

Acondicionador

de aire

*ENERGY STAR ® labeled product

La secci6n en espahol empieza en la pdgina 35

ENERGYSTAR

As an ENFaRGY STAR ® partner, GE has

determined that tiffs product meets

the ENERGY STAR ® guidelines for

energy efficiency.

Writethemodelandserial numbershere:

Model #

Serial #

Find these numbers on a label on the

side of the air condifione_.

494608 12-08JR

IMPORTANTSAFETYINFORMATION.

READALLINSTRUCTIONSBEFOREUSING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire, electric shock

or personal injury.

SAFETYPRECAUTIONS

}}Use this appliance only for its intended }}

purpose as described in this Owner's

Manual.

iii}i}i

iii}i}}li_

This air conditioner must be properly

installed in accordance xdth the Installation

Instructions before it is used.

Never unplug your air conditioner by pulling

on the power cord. Always _ip plug frmly

and pull straight out flom the receptacle.

Replace immediately 'allelectric ser\@e

cords that have become flayed or otherwise

damaged. A damaged power supply cord

must be replaced with a new power supply

cord obtained flom the manufhcturer and

not repaired. Do not use a cord that shows

cracks or abrasion damage along its len_h

or at either the plug or connector end.

iii}i}i

iii}i}}li_

Turn the unit OFFand unplug your air

conditioner before making any repairs

or cleaning.

NOTE: Westronglyrecommendthatanyservicing

be performedbya qualified individual.

For your satety...do not store or use

combustible materials, gasoline or other

flammable vapors or liquids in the x,icinity

of this or any other appliance.

All air conditioners contain refligerants,

which under federal law must be removed

prior to product disposal. If you are getting

rid of an old product with refligerants,

check with the company handling disposal

about what to do.

If the receptacle does not match the plug,

the receptacle must be changed out by a

qualified electrician.

HOWTOCONNECTELECTRICITY

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord.

For personal safety, this appliance must be

properly grounded.

DONOT use anadapterplug with this appliance.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall

outlet to minimize the possibility of electric

shock hazard flom this appliance.

Power cord includes a current intermpmr

dex,ice. A test and reset button is prox,ided on

the plug case. The dex,ice should be tested on a

periodic basis by first pressing the rESrbutton

and then the RESErbutton while plugged into

the outlet. If the TESTbutton does not trip

or if the RESETbutmn will not stay engaged,

discontinue use of the air conditioner and

contact a qualifed ser\,ice technician.

Have the wall outlet and circuit checked by

a qualified electrician to make sure the outlet

is properly _ounded.

Where a 2-prong wall outlet is encounmred,

it is your personal responsibility and obligation

to have it replaced with a properly grounded

3-prong wall outlet.

The air conditioner should always be plugged

into its own indix,idual electrical outlet which

has a voltage rating that matches the rating

plate.

This prox,ides the best performance and also

prevents overloading house xdring circuits

which could cause a fire hazard flom

overheated xdres.

See the Installation Instructions, Electrical

Requirements section for specific electrical

connection requirements.

WARNING!

USEOFEXTENSIONCORDS--115-Voltmodelsonly

Because of potential safety hazards under certain

conditions, we strongly recommend against the

use of an extension cord.

However, if you must use an extension cord,

it is absolumly necessa U that it be a UL-listed,

14 gauge, 3:wire grounding type appliance

extension cord ha\,ing a _ounding type plug

and outlet and that the electrical rating of the

cord be 15 amperes (minimum) and 125 vohs.

-4,CAUTION:

DO NOT usean extension cord with any ofthe

230/208 voltmodels.

ge.com

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCTIONS

Aboutthe controlsontheair conditioner

Features and appearance will varg

Lights next to the touch pads on the air conditioner control panel indicate the selected settings.

Light indicatesthe unit

Thedisplayalwaysshowsthe is in the temperatureor

roomtemperatureexceptwhen delaytime Set mode.

settingthe Settemperatureor 1

the Delaytimer. __i_ t

e _=o 77,o t

.... LVj

m Low w Cool

Lightindicates the delaytimer is set.

_1 Delay1-24hr

Delaytimer , Delaytimer Increase

Decrease

O Modeselect , Auto Fanon/off

0 Fanspeed , FanspeedIncrease

Decrease

0 Temperature ) Unit poweron/off

set Increase

and Decrease

AirConditionerControls

Remote Control

Contro/s

O ower Pad

Turns air conditioner on _md off. _¥hen

turned on, tile display will show tile room

temperature.

0 Display

Shows tile room temperature or time

remaining on the Delay fimeL Shows the Set

mmpemture while setting the mmpetature in

Coolor Energy Saver modes. The Set light will

mrn on while setting.

NOTE:The display will change to show file

room temperature after settings have been

made. To recall the Set mmpemmre, press the

TempIncrease • or Decrease • pads.

O empIncrease •/Decrease • Pads

Use to set temperature when in Cool or Energy

Savermode. The Setlight will turn on while

setting.

O Delay fimerlncrease • (+)/Decrease • (-)

Pads

Each touch of the Increase •/Decrease •

pads on the unit or the Increase +/Decrease -

pads on the remote control will set the delay

time when using the Delay1-24hrtimer (@).

The Setlight will mrn on while setting.

O an Speed Pads

Use to set tile fan speed to LOW,Med, High

or Auto on the unit. NOTE:On the remote

control, use the fan speed Increase +/

Decrease - pads to set the fan speeds to LOW,

Med or High. Use the Auto pad to turn Auto

fan on.

O ode Pad

Use to set tlle air conditioner to Cool, Energy

Saver or Fan Only mode.

Delay Pads

Delay ON--When the air conditioner is offl it

can be set to automatically come on in 1 to 24

hems at its previous mode and fan settings.

Delay OFF--When the air conditioner is on,

it can be set m automatically mrn off in 1 m

24 hems.

How toset:

Press file Delay 1-24hr pad on the unit or

die _ pad on file remora conuol. Each touch

of the Increase •/Decrease • pads on the

unit or the Increase +/Decrease- pads on

tile remote control will set the timer in

1-hour intervals. The Set light will mrn on

while setting.

To review die remaining time on die Delay

1-24hrtime_, press the Delay 1-24hr pad on the

unit or the 0" pad on the remote control. Use

the Increase •/Decrease • pads on the unit

or the Increase +/Decrease-pads on the

remote control to set a new time if desired.

Tocancel the timer, press tt_e Delay 1-24hr pad

until tile light on the Delay 1-24hr pad goes off:

Power Outage Recovery Feature

In tile case of a power outage or interruption, tile

unit will automatically re-start in the settings last

used after tile power is restored. If tile Delay1-24hr

feature was set, it will resume countdown. You may

need to set a new time if desired.

ge.corn

CoolMode

Use file Coohnode at Low, Med, Highor Auto Fan

Speed for cooling. Use the TemperatureIncrease • /

Decrease• pads to set the desired mmperature

between 64°F and 86°F in 1°F increments.

An electronic dlemlostat is used to maintain die

room temperature. The compressor will cycle on

and off m keep the room at the set level of comfort.

Set the fllemlosmt at a lower number and the indoor

air will become coolex. Set the tllemK_stat at a higher

nttmber and the indoor air will become wamleL

NOTE:ff theairconditionerisoffandisthenturnedon

whilesettoa Coolsettingorif turnedfromafansetting

toa Coolsetting,it maytakeapproximately3minutes

forthecompressortostartandcoolingtobegin.

CoolingDescriptions

ForNormalCooling--Selectthe Coolmode and

Highor Med fan with a middle set temperature.

ForMaximum Cooling--Select the Coolmode

and Highfan with a lower set temperature.

ForQuieter& NighttimeCooling--Select the

Coolmode and LOWfan with a middle set

temperature.

Do Not Operatein FreezingOutdoorConditions

This cool-only air conditioner was not designed for

freezing outdoor conditions. It Illttst not be used in

freezing outdoor conditions.

Energy Saver Mode

Controls the fan.

0N--The fan will cycle on and offwidl tlle

compressoL This results in wider vaIiafions of room

mmpetaUne and humidil),. NormaUy used when the

room is unoccupied. NOTE: Thefan maycontinue to run

fora short time after the compressorcgclesoff.

OFF--The fan runs all the time, while die

compressor cycles on and off.

Fan OnlyMode

Use the FanOnlyModeat Low,Medor Highfan

speed to provide air circulation and filtering

without cooling. Since fan only settings do not

provide cooling, a Set temperaune cannot be

enmred. The room mmpemutre will appear

in the display.

NOTE:AutoFanSpeedcannotbeusedwhenin the

FanOnlyMode.

Auto Fan Speed

Set to Auto fan speed for die fan speed to

attmmaficMly set m die speed needed m provide

optimum comfort settings with the set temperautre.

If file room needs more cooling, file fan speed

will attmmadcally increase. If the room needs less

cooling, the fan speed will attmmatically decre_kse.

NOTE:AutoFanSpeedcannotbeusedwhenin the

FanOnlyMode.

Air Direction

Use die levers m adjust die air direction left and

right.

Fingertip pressure on die louver banks adjusts the

air direction up or down.

Remote Control

To ensure proper operation, aim file remora

conUol at the signal receiver on the air

condifione_.

The remote conuol signM has a range of

lap m 20 feet.

Make sure nodfing is between die air conditioner

and the remora conuol that could block the

sigmal.

Make sure batteries are flesh and instaUed

correcdy as indicated on tile remora conuol.

Careand cleaning oftheair conditioner.

Grille and Case

Turn the air conditioner off'and remove the plug To clean, use water and a mild detergent. Do not

flom the wall outlet before cleaning, use bleach or abrasives.

Air Filter

The air filter behind the front grille should be

checked and cleaned at least every 30 days or

more often if necessary.

Toremove:

Push on one side of the filter edge and pull it out

the oilier side.

Clean the filter with warm, soap), wateL Rinse and

let the filter dry before replacing it. Do not clean

the filter in a dishwasher.

CAUTION:DoNoropera,e,heair

conditioner without a filter becausedirt and lint will clog

it andreduceperformance.

OutdoorCoils

The coils on the outdoor side of the air conditioner

should be checked regularly. If they are clogged

with dirt or soot, they may be professionNly cleaned.

How to Insert the Batteries in the Remote Control

I--f] Remove the batte D,cover by sliding it

according to the a_xow direction.

Insert new batteries, making sure that the (+)

and (-) of battery are inst_dled correctly.

[j] Reatmch the cover by sliding it back

into position.

NOTES:

Use 2 "_" (1.5 volt) alkaline batteries. Do not

use recha_geable batteries.

Remove the batteries flom the remora control if

the sysmm is not going m be used for a long time.

ilnsta,,at,onnsttuct,onsIAirC°ndit'°nerl

I F_ Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: ge.com I

In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

IMPORTANT - Savethese

instructions for local inspector's use.

• IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer- Be sure to leave these

instructions with the Consumer.

• Note to Consumer- Keep these

instructions for future reference.

• Skill level - Installation of this appliance

requires basic mechanical skills.

• Completion time- Approximately 1 hour

• We recommend that two people install

this product.

• Proper installation is the responsibility

of the installer.

Product failure due to improper installation

is not covered under the Warranty.

You MUST use all supplied parts and use

proper installation procedures as described

in these instructions, and any separate kit

instructions, when installing this air

conditioner.

(_ ELECTRICAL REQUIREMENTS

Some models require a 115/120-volt AC,

60 Hz grounded outlet protected with a

15-amp time delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the

possibility of electric shock hazard. If the wall

outlet you plan to use is only a 2-prong outlet,

it is your responsibility to have it replaced with

a properly grounded 3-prong wall outlet.

Some models require 230/208-volt AC,

protected with a time delay fuse or circuit

breaker. These models should be installed

on their own single branch circuit for

best performance and to prevent

overloading house or apartment wiring

circuits, which could cause a possible

fire hazard from overheating wires.

- CAUTION:

Do not, under any circumstances, cut or

remove the third (ground) prong from the

power cord.

Do not change the plug on the power cord

of this air conditioner.

Aluminum house wiring may present special

problemsmconsult a qualified electrician.

If the sill support bolts do not contact the

window sill, or if you have a window

without a sill, you must order accessory kit

RAK87 to properly install this air conditioner.

Call 800.626.2002 or visit ge.com.

TOOLS YOU WILL NEED

Phillips head screwdriver

Adjustable wrench

Flat-blade screwdriver

Pencil

Level

Ruler or tape measure

Scissors or knife

Power cord includes a current interrupter

device. A test and reset button is provided on

the plug case. The device should be tested on a

periodic basis by first pressing the TEST button

and then the RESET button while plugged into

the outlet. If the TEST button does not trip or

if the RESET button will not stay engaged,

discontinue use of the air conditioner and

contact a qualified service technician.

Installation Instructions

PARTS INCLUDED

Left

accordion.

panel "_

Window sash seal

(thin, adhesive-backed)

Foam t

window gasket-------_'_,_..__k>,v" SJli suppo rt (2)

_.____ Nut(2)

Bolt (2)

Top mounting rail

Top mo "_

seal strip

Right

accordion

panel

Window locking

Type A (6) Type B (7) Type C (6) Type D (3) bracket (2)

Installation Instructions

ITI WINDOW REQUIREMENTS

• These instructions are for a standard

double-hung window. You will need to

modify them for other types of windows.

CAUTION: If the sill support

bolts do not contact the window sill, or

if you have a window without a sill, you

must order accessory kit RAK87 to

properly install this air conditioner.

Call 800.626.2002 or visit ge.com.

• The air conditioner can be installed

without the accordion panels if needed

to fit in a narrow window. See the

window opening dimensions.

• All supporting parts must be secured

to firm wood, masonry or metal.

• The electrical outlet must be within

reach of the power cord.

B===8

15 1/2" min.

25 1/4" to 38 1/8"

(With accordion panels)

D-I STORM WINDOW REQUIREMENTS

A storm window frame will not allow the air

conditioner to tilt toward the outside, and

will keep it from draining properly. To adjust

for this, attach a piece of wood to the sill.

WOOD PIECES -

WIDTH: 2"

LENGTH: Long enough to fit inside the

window frame.

THICKNESS: To determine the thickness,

place a piece of wood on the sill to make

it 1/2" higher than the top of the storm

window frame or the vinyl frame.

Attach securely with nails or screws

provided by the installer.

1/2" higher

than vinyl frame

L (on some windows)

1/2" higher ________ _VVood

than storm

window rl

frame _ Sill Fr _

Storm window

frame - r_ Vinyl frame I !

[] REMOVE THE AIR CONDITIONER

FROM THE CASE

[] Remove and save the 2 screws from the

lower sides of the front grille.

FRONT

r_ Grasp the lower corners of the grille while

pressing in on the case sides with your

finger tips. Pull out to release and lift it up.

NOTE: Do not pull the bottom edge

toward you more than 3" or you may

damage the tabs of the grille.

t t

FRONT

rc-] Remove the ground screw from each side

of the case. Keep them in a safe location.

FRONT

[] Slide the air conditioner from the case by

gripping the base pan handle and pulling

forward while bracing the case. Do not

pull or lift on the styrofoam discharge area.

Do not

pull or

lift in

this

area--

damage

to the

unit may

result

FRONT

Installation Instructions

141ATTACH THE TOP MOUNTING

RAIL SEAL STRIP

Remove the backing from the top mounting

rail seal strip and attach the seal strip to

the bottom of the top mounting rail, along

the front edge. Allow the seal strip to

overlap 3/8" on each end.

3/8"

Top mounting rail

Remove

backing

seal

strip

3/8"

FRONT VIEW Top mounting rail

[ i

3/8" overlap Seal strip 3/8" overlap

[] INSTALL THE

SIDE ACCORDION PANELS

[A1 Slide the left and right accordion panels

into the top and bottom mounting rails.

['_ Attach the accordion panels to the case

using 3 Type A screws on each side.

Top mounting rail

Accordion

panel

\.\

BACK

Bottom mounting rail

[] INSTALL THE TOP MOUNTING

RAIL ONTO THE CASE

Attach the top mounting rail onto the top

of the case with 3 Type B screws.

)e B

screws

171PREPARE THE WINDOW

• Cut the window sash seal to the window

width and stick the adhesive side to the

bottom of the sash.

INSIDE

Installation Instructions

I-KIINSTALL THE CASE IN THE

WINDOW

[_] Open the window and mark the centerline

of the window sill.

['_ Carefully place the case on the window

stool and align the center mark on the

bottom front with the centerline of the sill.

['_ Pull the window down behind the top

mounting rail.

NOTE: Do not shut the window so tightly that

movement of the accordion panels is

restricted.

['_ Select the position that will place the sill

supports near the outermost point on the

sill. Place the short side of the sill supports,

on the case bottom, toward the window.

Attach the sill supports to the case track

hole in relation to the selected position

using 2 Type B screws in each support.

I I

Long side

of sill

supports

OUTSIDE

['_ Adjust the bolt and the nut in each

support so that the case is installed with a

slight tilt to the outside. Use a level; about

1/2 bubble will be the correct case slant to

the outside.

CAUTION: Ifthesillsupport

bolts do not contact the window sill,

or if you have a window without a sill,

you must order accessory kit RAK87 to

properly install this air conditioner. Call

800.626.2002 or visit ge.com.

1-81INSTALL THE CASE IN THE

WINDOW (CONT.)

['_ Secure the case to the window sill by

using 3 Type D screws.

['G-]Pull the accordion panels to each window

sash track. Attach them on each side to the

window sash and the window sill using

4 Type C screws.

Installation Instructions

[] INSTALL SUPPORT BRACKET AND

FOAM TOP WINDOW GASKET

[] -&CAUTION:

To prevent broken glass

or damage to windows,

on vinyl or other

similarly constructed

windows, attach the

support bracket to the

window side jam.

Vinyl

Attach the support

bracket with one

Type C screw.

Wood

['_ Cut the foam top window gasket to the

window width.

['_ Stuff the foam

between the

glass and the

window to

prevent air and

insects from

getting into the room.

NOTE: If the gasket supplied does not fit

your window, obtain appropriate material

locally to provide a proper installation seal.

[] INSTALL THE AIR CONDITIONER

IN THE CASE

_] Slide the air conditioner into the case by

the base pan. Do not push on the controls,

styrofoam air discharge housing or the

finned coils. Make sure the air conditioner

is firmly seated.

Do not press on

these areas--

damage to the

unit may result

Base Pan

I_1 INSTALL THE AIR CONDITIONER

IN THE CASE (CONT.)

[_] Replace the 2 ground screws removed

earlier, one on each side of the case.

IMPORTANT: The ground screws must be

reinstalled to ensure a proper ground.

[] Attach the front grille to the case by

inserting the tabs on the grille into the

slots on the front top of the case. Push

the grille in.

[]

• , C:::_@

Secure the front grille to the case by

replacing the 2 screws removed earlier.

Press on the top of the grille to help

with side screw installation.

['_ Connect power.

TroubleshootingTips.

Possible Causes What ToDo

Air conditioner The air conditioner • Make sure the air conditioner plug is pushed

does not start is unplugged, completely into the outlet.

The fuse is blown/circuit • Check the house fitse/circuit breaker box and replace

breaker is tripped, the fitse or reset the breakeL

Power failure, • The unit will automatically re-start in file settings last

used after file power is restored.

• There is a protective time delay (approximately

3 minutes) to prevent tripping of the compressor

overload. For this reason, the unit may not start

normal cooling for 3 minutes after it is turned

back on.

The current interrupter

device is tripped.

• Press the RESETbuttonlocated on the power cord plug.

• If tim RESETbuttonwill not stay engaged, discontinue

use of the air conditioner and contact a qualified

service teclmician.

Air conditioner does Airflow is restricted. • Make sure there are no curtains, blinds or fiuniuue

notcoolas itshould blocking the flont of the air condifioneL

The temp control may • On models with touch pads: In the Cool mode, press the

not be set correctly. Decrease • pad.

• On models wifll control knobs, turn the temperature

knob to a higher numbeL

The air filter is dirty. • Clean the filter at least eve_T 30 days.

See the Care and Cleaning section.

The room may have been hot. • When the air conditioner is first turned on, you need

m allow time for the room m cool down.

Cold air is escaping. • Check for open fiunace registers and cold air reuuns.

Cooling coils have iced up. • See "Air conditioner freezing up" below.

Air conditioner

freezingup

Ice blocks the air flow

and stops the air conditioner

from cooling the room.

• On models Mill conUol knobs, set file mode conuol at

High Fan or High Coolwith the Tempat I or 2.

• On models with touch pads, set the controls at HighFan

or High Cool and set the thermostat m a higher

temperature.

The remote control The batteries are inserted • Check file position of file batteries. They should be

is not working incorrectly, inserted in the opposite (+) and (-) direction.

The batteries may be dead. • Replace the batteries.

Water drips outside Hot, humid weather. • Tiffs is nomml.

Water drips indoors The air conditioner is not • For proper water disposal, make sure file air conditioner

tilted to the outside, slants slightly flom the case flont to the real

Water collects in Moisture removed from air • Tiffs is nomml for a short period in areas with little

base pan and drains into base pan. humidity; normal for a longer period in re, y humid are_ts.

Normal Operating Sounds

You may hear a pinging noise caused by wamr

being picked tap and tinown against the

condenser on rainy days or when the humidity

is high. This desigm feaune helps remove

moisune and improve efficiency.

}_You may hear the thermostat click when the

compressor cycles on and off:

Water will collect in file base pan during

high humidity or on rainy days. The wamr

mW overflow and drip flom the outdoor side

of the unit.

}i_The fan may run even when the compressor

does not.

r_,_

¢b

._ Notes.

.wire..wire.

Please place in envelope and mail to:

Veuillez mettre dans une enveloppe et envoyez _ :

OWHERSHJPREGJSTRATJOH

P.O. BOX1780

MISSISSAUGA,OHTARIO

L4Y4G1

(FORCAHADJAHCOHSUMERSOHLY)

For Canadian

Customers

Pour les

Consommateurs

Canadiens

Pleaseregisteryourproducttoenableustocontactyou Veuillezenregistrervotreproduitafindenouspermettrede

in the remote event a safety notice is issued for this product communiquer avec vous sijamais un avis de sOcur_ concemant

and to allow for efficient communication under the terms ce produit _ait _mis et de communiquer facilement avec vous en

of your warranty, should the need arise, vertu de vo1_egarardJe,si le besoin s'en fair senlJr.

REGISTERON-UNE: www.geappliances.ca MAILTO: P.O.BOX1780,MISSISSAUGA

ENREGISTREMENTSURINTERNET,&,: www, ele_ramenage_sge,ca POSTERA: ONTARIO,L4Y401

[][] MISS/MLLE.MR'/M[][] Ns.MRS'/MNE"FIRSTNAME/PRENOM LASTNAME/NOM

STREETNO/N° RUE STREETNAME/RUE

CITY/VlLLE

E OOOE,,NOREOIT LEPHONE

DIDYOUPURCHASEASERVICECONTRACTFORTHISAPPLIANCE?

AVEZ-VOUSACHETt_UN CONTRATDESERVICEPOURCETAPPAREIL?

APT.NO/APP./ RR#

PROVINCE POSTALCODE/POSTAL

YES/OUI [] IFYES/ SIOUhEXPIRATION

Y/A M D/J

NO/NON D

NAMEOFSELUNGDEALER/NOM DUMARCHAND MODEL/MODELE

INSTALLA_ONDATE/DATED'INS_ALLA]ION

Y/A M D/J CORRESPONDENCE [] ENGUSH

CORRESPONDANCE [] FRAN_AIS SERIAL/SERIE

[] Ido notwishtoreceiveanypromotionaloffersregardingthisproduct.

[] Jenedesirepasrecevoird'offrespromotionneHesconcemantceproduit.

GEAir Conditioner--One- YearLimited Warranty.(For customers in the U.S.A.)

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care_ technician. Toschedule service,

visit us on-line at ge.com, or call 800.GE.CARES(800.432.2737).

Have serial number and model number available when calling

for service.

Staple yourreceipt here.

Proof of the original purchase

dateis needed to obtain service

under the warranty.

i i I

Fromthedateof the

arigina!purchase

GEWill Replace:

Anypartof the air conditioner which fidls due to a defect in materials or workmanship.

During this limited one-year warranty, GE will also provide, free of charge, all labor and related

service to replace the defective part.

Service trips to your home to teach you how to

use the product.

Improper installation, delivery or maintenance. If you

have an installation problem, or if the air conditioner

is of improper cooling capacity for the intended use,

contact your dealer or installer. You are responsible

for providing adequate electrical connecting facilities.

Failure of the product resulting from modifications to

the product or due to unreasonable use including failure

to provide reasonable and necessary maintenance.

In commercial locations, labor necessary to move the

unit to a location where it is accessible for service

by an individual technician.

Replacement of house fuses or resetting of circuit

breakers.

Failure due to corrosion on models not corrosion-

protected.

Damage to the product caused by improper power supply

voltage, accident, fire, floods or acts of God.

Incidental or consequential damage caused by possible

defects with this air conditioner.

Damage caused after delivery.

EXCLUSION OFIMPLIED WARRANTIES--Your sole and exclusive remedy is product repair as provided in this

Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a

particular purpose, are limited to one year or the shortest period allowed bylaw.

This warranty is extended to the original purchaser and any succeeding owner for products purchased for home

use within the USA. If the product is located in an area where service by a GEAuthorized Servicer is not available,

you may be responsible for a trip charge or you may be required to bring the product to an Authorized GEService

location for service. In Alaska, the warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty gives

you specific legal rights, and you may also have other rights which vary from state to state. Toknow what your

legal rights are, consult your local or state consumer affairs office or your state's Attorney General

Warrantor: General Electric Company.Louisville, KY 40225

GEAir Conditioner--One- YearLimitedWarranty. ForcustomersintheCanada

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care_ technician. For service, call

1.800.561.3344.Please have serial number and model number

available when calling for service.

Staple yourreceipt here.

Proof of the original purchase

date is needed to obtain service

under the warranty.

OneYear

Fromthedate Ofthe

originalpurchase

Mabe Will Replace:

Anypartof file air conditioner which fails due to a defect in materials or workmanship.

Durhlg this limitedone-yearwarranty,Mabe will also provide, free of charge, all labor and

related service to replace the defective part.

Service trips to your home to teach you how to

use the product.

Improper installation, delivery or maintenance. If you

have an installation problem, or if the air conditioner

is of improper cooling capacity for the intended use,

contact your dealer or installer. You are responsible

for providing adequate electrical connecting facilities.

Failure of the product resulting from modifications to

the product or due to unreasonable use including failure

to provide reasonable and necessary maintenance.

In commercial locations, labor necessary to move the

unit to a location where it is accessible for service

by an individual technician.

Replacement of house fuses or resetting of circuit

breakers.

Failure due to corrosion on models not corrosion-

protected.

Damage to the product caused by improper power supply

voltage, accident, fire, floods or acts of God.

Incidental or consequential damage caused by possible

defects with this air conditioner.

Damage caused after delivery.

EXCLUSION OFIMPLIED WARRANTIES--Your sole and exclusive remedy is product repair as provided in this

Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitness for a

particular purpose, are limited to one year or the shortestperiod allowed by law.

This warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada

for home use within Canada. In-home warranty service will be provided in areas where it is available and deemed

reasonable by Mabe toprovide.

Some provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above exclusion

may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from

province toprovince. Toknow what your legal rights are in your province, consult your local or provincial consumer

affairs office.

Warrantor: Mabe Canada Inc.,

Burlington, Ontario

Consignes de s&_rit_ ............ 20, 21

Consignes d 'utilisation

ModUles dot_s touches

_t ef_leurement ................... 22, 23

Entretien et nettoyage

Filtre it air .......................... 24

Serpentins ext4fieurs ................. 24

Instructions de montage ........... 25-30

Conseilsde d pannage .............. 3

Bruits normaux de fonctionnement ..... 31

Assistance a la clientble

Assistance it la clientb.le ............... 36

Garantie ............................ 35

Enregistrement du titre

de propriF.tF. ..................... 33, 34

AEM I O*

AEM 12 *

A :Q1o

AEQ12

* Produits homologu_s ENERGYSTAR®

ENERGYSTAR

En rant que partenaire d'ENERGY STAR ®,

GE a d&ermin_ que ce produit _mit

conforme aux exigences d'efficacit_

&_erg_fique d'ENERGY STAR ®.

Inscrivezici les numomsde modoleet desorie:

Numomdemodole:

NumorodeS&ie :

Vous trouverez ces nmn_ros sur l'bfiquette

appos_e sin le c6t_ du climatiseur.

Au Canada, visitez-nous au •

www.electromenagersge.ca

w -=

CT_

v.,.2.

p" F

/MPORTANTESCONS/GNESDESECUR/TE.

VEU/LLEZL/RETOUTESLESCONS/GNESAVA/VTUT/L/SAT/ON.

Pour votre s#curit#, les informafions contenues dans ce manuel doivent Otresuivies afin de minimiser

les risques d'incendie, de chocs #lectriques ou de blessures corporefles.

CONSIGNESDESECUR/TE

iiiiiil

iii}i}}li_

N'udlisez cet appareil qu'aux fins pr&_ms

d_crites dans le manuel d'udlisadon.

Ce climatiseur dolt _tre correctement

install_ corttk)rm_ment aux Instructions

d'lnstalladon infant toute udlisadon.

Ne ddbranchezjamais votre climadseur en

drant sur le cordon d'alimentadon. Prenez

touiours refinement la fiche en main et drez

pour la sordr de la prise.

Remplacez immddiamment tout cordon

dlectrique usd ou endommagd. Un cordon

d'alimentadon endommagd dolt atre

remplacd par un nouveau cordon

d'alimentadon obmnu Nl thbricant. Ne

r@arez pas le cordon endommagd. N'udlisez

pas un cordon fissurd ou prdsentant des

dommages N_s aux trottements soit sur

sa longueur ou aux extrdmitds Nl c6td

de la fiche ou Nl raccord.

iii}i}i

iii}i}}li_

Eteignez votre climatiseur et ddbranchez-le

infant d'ettectuer des r@aradons ou de le

nettoyer.

REMARQUE: Nousvousrecommandonsde faire

effectuer la maintenancepar un technicienqualifi#.

Pour votre sdcuritd, ne stockez pas et

n'udlisez pas de matdriaux combustibles,

d'essence ou d'autres vapeurs et liquides

inflammables dans les parages de cet

appareil ou de rout autre appareil.

Tousles climadseurs condennent des fluides

/iigorigb.nes qui, conIbrmdment, it la

ld_slation/_ddrale doivent _tre refirds avant

la mise au rebut de l'appareil. Si vous mettez

au rebus un ancien appareil contenant des

fluides fiigorig_nes, v&ifiez la proc&ture it

suivre auprSs de la compagnie responsable

de l'dliminadon.

Si la prise de courant est d'un tk_rmat

ditt_rent de la fiche, cette prise dolt _tre

changde par un dlectricien qualifid.

BRANCHEMENTSELECTRIOUES

No coupez pas ou n'enlevez pas, sous aucun

prOtexte, la troisifime broche de mise _ la terre

du cordon d'alimentation. Pour des raisons

de sOcurit#, cet appareil do# Otrecorrectement

mis _ la terre.

N'utilisezPASd'adaptateuraveccetappareil.

Le cordon d'alimentadon de cet appareil

est dquipd d'une fiche it trois broches (pour

une mise it la terre) qui s'adapm a la prise

de courant standard it 3 broches (pour une

mise itla terre) pour minimiser les risques

de chocs dlectriques par cet appareil.

Le cordon d'alimentadon est dquipd d'un

dispositif d'intermpdon du courant. Un

bouton d'essai et de rdenclenchement est

fburni sur le boider de la prise. Vous devez

roster le mdcanisme rdguli&rement en

appuyant d'abord sur le boumn rest(ess i)

puis sur le bouton fiE.gET(rdenclenchement)

lorsque l'appareil est branchd. Si le bouton

rest(ess i)ne bascule pas ou si le bouton

fiE.gEE(rdenclenchement) ne reste pas

enclenchd, cessez d'utiliser votre dimadseur

et appelez un technicien de ser_,ice qualifid.

Faites vdrifier la prise murale et le circuit

dlectrique par un dlectricien qualifid pour

s'assurer que le systbme est correctement

mis it la terre.

Dans le cas d'une prise biphasde,

l'installateur a la responsabilitd et l'obligadon

de la remplacer par une prise triphasde

correctement mise it la terre.

Le climatiseur dolt toujours _tre branchd

it sa propre prise dlectrique d'une mnsion

nominale correspondant it celle indiqude

sur sa plaque signalddque.

Ceci permet d'obtenir un meilleur rendement

du climadseur et &ite de surcharger les circuits

dlectriques du domicile qui risque

d'occasionner un incendie en surchauffant.

Consultez les Consignes d'Installations, dans

la secdon Exigences Electriques pour les

exigences de branchements dlectriques

pardculiers.

Page is loading ...

GE AEQ10AMG1 Owner's manual

Brand: GE

Model: AEQ10AMG1

Type: Owner's manual

This manual is also suitable for

Download PDF

report

in other languages

français: GE AEQ10AMG1 Le manuel du propriétaire
español: GE AEQ10AMG1 El manual del propietario

GE AEQ10AMG1 Owner's manual

This manual is also suitable for

GE AEQ10AMG1 Owner's manual

in other languages

Related papers

Other documents