Dunkirk Helix VLT Vertical Laser Tube, Wall Hung Modulating Condensing Boiler Installation, Operation & Maintenance Manual

WALL MOUNTED

CONDENSING GAS BOILER

INSTALLATION, OPERATION &

MAINTENANCE MANUAL

An ISO 9001-2008 Certified Company

P/N# 240008888, Rev. A [05/2011]

H

Models

DKVLT-050

DKVLT-075

DKVLT-100

DKVLT-150

DKVLT-200

2201 Dwyer Avenue, Utica NY 13504-4729

web site: www.ecrinternational.com

2

(C)

DIMENSIONS

FIGURE 1-1 Dimensions

(D)

Wall Hanging

Bracket

(D)

(A)

(F)

Vent Connector

Combustion Air

Safety Relief

Valve

Connection

(¾ NPT)

(B)

Condensate Drain Connection (H)

Return Water (E)

Supply Water (E)

Gas Connection (G)

(I)

(J)

Table 1 : Physical Data

Models

050/075/100 150/200

Width (A)

20"

(508mm)

23"

(584mm)

Height (B)

31"

(787mm)

42"

(1092mm)

Depth (C)

14"

(356mm)

16.0"

(406mm)

Bracket (D)

28"

(711mm)

40"

(1016mm)

Water

Connections

Location

(I)

2"

(51mm)

2"

(51mm)

Size (E) 1-1/4" NPT

1-1/4" NPT

Gas

Connection

Location

(J)

4-1/2"

(114mm)

4-1/2"

(114mm)

Size (G)

1/2"

NPT

3/4"

NPT

Condensate Drain

Connection (H)

3/4" NPT

Weight

Shipping

111 lb

(50 kg)

~182 lb

(83 kg)

Unit

91 lb

(41 kg)

~157 lb

(71 kg)

Vent Connector

2"

(51mm)

3"

(76mm)

3

1 - Introduction ............................................................................................................................... 4

2 - Important Safety Information ....................................................................................................5

3 - Component Listing .....................................................................................................................6

4 - Locating Boiler ...........................................................................................................................9

5 - Hydronic Piping ........................................................................................................................11

5.2 Special Conditions ................................................................................................................... 11

5.3 Safety Relief Valve and Air Vent .... ............................................................................................11

5.4 Trim Piping ............................................................................................................................. 12

5.5 System Piping ......................................................................................................................... 12

6 - Combustion Air And Vent Piping ...............................................................................................17

6.2 Removal of Existing Boiler From Common Vent System..................................................................17

6.3 Materials ............................................................................................................................... 17

6.4 Pipe Installation ...................................................................................................................... 18

6.5 Termination ............................................................................................................................ 18

6.6 Condensate Piping ................................................................................................................... 24

7 - Gas Supply Piping ....................................................................................................................25

8 - Electrical Connections ..............................................................................................................27

8.3 Line Voltage Connections .......................................................................................................... 27

8.4 External Connections ............................................................................................................... 27

9 - Start Up Procedure ...................................................................................................................29

10 - Operating Instructions ........................................................................................................... 33

11 - General Maintenance And Cleaning ........................................................................................ 34

12 - Ratings And Capacities ........................................................................................................... 37

13 - Troubleshooting .....................................................................................................................38

14 - Wiring Diagram ...................................................................................................................... 52

15 - Glossary .................................................................................................................................54

Appendix A - Control Module .........................................................................................................56

1.1 Introduction ........................................................................................................................... 56

1.2 Operation ............................................................................................................................... 56

1.3 Status Indication ..................................................................................................................... 56

1.4 Sequence of Operation ............................................................................................................. 57

1.5 Theory of Operation................................................................................................................. 59

TABLE OF CONTENTS

Information and speciﬁ cations outlined in this manual in effect at the

time of printing of this manual. ECR International reserves the right to

discontinue, change speciﬁ cations or system design at any time without

notice and without incurring any obligation, whatsoever.

Check our website frequently for updates: www.ecrinternational.com

4

1.1 Designated Use

Hot water heating boiler.•

Indoor installation.•

Closet or alcove installation.•

Direct vent boiler.•

For use with natural gas or liqueﬁ ed petroleum gases •

(LP/propane).

1.2 The unit MUST NOT:

• Directly heat potable water. Indirect heating is acceptable.

• Heat water with non-hydronic heating system chemicals

present (example, swimming pool water).

Exceed 50 psig (344 kPa) system pressure.•

Exceed 195°F (90.5°C) system design temperature.•

1.3 Operational Features

Modulating: 20-100%.•

Integral Dual Limit.•

Integral Low Water Cutoff (with test button).•

Outdoor Temperature Reset.•

Integral Multiple Boiler Control.•

1 - INTRODUCTION

5

NOTICE

Used to address practices not related to personal

injury.

2.3 Installation shall conform to requirements

of authority having jurisdiction or in absence of

such requirements:

National Fuel Gas Code, ANSI Z223.1/NFPA 54•

.

National Electrical Code, NFPA 70.•

2.4 Where required by authority having

jurisdiction, installation shall conform to

Standard for Controls and Safety Devices for

Automatically Fired Boilers, ANSI/ASME CSD-1.

Additional manual reset low water cutoff may be required.

2.5 Requirements for Commonwealth of

Massachusetts:

Boiler installation must conform to Commonwealth of

Massachusetts code 248 CMR which includes but is not

limited to:

Installation by licensed plumber or gas ﬁ tter.•

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

!

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

!

DANGER

Indicates a hazardous situation which, if not avoided,

WILL result in death or serious injury

!

This is the safety alert symbol. Symbol alerts you to

potential personal injury hazards. Obey all safety messages

following this symbol to avoid possible injury or death.

2.2

Become familiar with symbols identifying

potential hazards.

2.1 General

Boiler installation shall be completed by qualiﬁ ed agency.

See glossary for additional information.

WARNING

Fire, explosion, asphyxiation and electrical shock

hazard. Improper installation could result in death

or serious injury. Read this manual and understand

all requirements before beginning installation.

!

2 - IMPORTANT SAFETY INFORMATION

6

3.1 Component Listing

User Interface

1.

(see Appendix A) - Displays

information regarding boiler condition. Allows

adjustment of boiler operating parameters. NOTE: Does

not replace thermostat used to control central heating

space.

Combustion Air Inlet (2"/3" )

2.

(see page 7 & 8)

Return Water From Heating System (In)

3.

(see

page 8)

-

Connection supplied at bottom of boiler.

Low Voltage Terminal Strip

4.

(see page 8) -

Connection of all low voltage wiring, including

thermostat. See section

8.

Igniter

5.

(see page 8)

Flame Sensor

6.

(see page 8)

Sight Glass

7.

(see page 8) - Permits observation of

burner ﬂ ame.

Burner

8.

(see page 35)

Combustion Chamber

9.

(see page 8)

Condensate Collector

10.

(see page 8)

Return Temperature Sensor

11.

(not shown)

Drain Valve

12.

(see page 12)

Heat Exchanger Ball Valve

13.

(see page 8)

Supply Water Outlet to Heating System (Out)

14.

(see pages 8) - Connections supplied for connecting

from bottom of boiler. See section 5.

Vent Temperature Sensor

15.

(see page 8)

Condensate Drain

16.

(see page 8) - Boiler produces

a liquid (condensate) as a by-product of combustion.

Condensate must be piped to appropriate drain. See

section 6.

Heat Exchanger Pump

17.

(see page 8)

Gas Shutoff Valve

18.

(see page 8)

- Fuel supply isolation

during servicing. See section 7

Combustion Air Blower

19.

(see page 8)

- Delivers

proper quantity of combustion air, receives fuel from

gas valve, mixes air and fuel sending mixture to burner

for combustion.

Gas (Control) Valve

20.

(see page 8)

- Delivers

proper quantity of fuel to Combustion Air Blower.

See section 7.

High Temperature Supply Switch

21.

(see page 8)

Low Water Cutoff

22.

(see page 8)

-

Senses inadequate

quantity of water. Turns off boiler before damage can

occur.

Safety Relief Valve

23.

(see pages 7 & 8) - Factory

supplied, Field installed. See section 5.

High Voltage Junction Box

24.

(see page 8) - For

connection of 120V components. See section

8

8.

Vent Connector

25.

(see pages 7 & 8) - See section 6.

Gas Connection

26.

(see page 8)

- See section 7.

Wall Hanging Support Bracket

27.

(see page 7) -

Integral to boiler. Allows wall mounting when used

with supplied wall mounting bracket. See section 4.

Power Switch

28.

(see page 7)

Air Vent

29.

(see page 7 & 8)

Control Module

30.

(see page 8)

Lower Jacket Panel

31.

(see page 7) - Gently pull upward

then forward to access.

Transformer

32.

(see page 8) - Supplies 24V power to low

water cutoff.

Pressure Test Port

33.

- (see page 8)

Combustion Analysis Test Port

34.

- (see page 8)

Return Water Sensor

35.

(see page 8)

User Interface -

36.

(see page 7)

3 - COMPONENT LISTING

7

3 - COMPONENT LISTING

FIGURE 3-1 Boiler Components (Viewed from Back of Boiler)

VENT CONNECTOR

NOTE:

See Section 5-3

For Safety Relief

Valve Piping

Instructions

COMBUSTION

AIR INLET

SAFETY RELIEF VALVE

AIR VENT

WALL HANGING

SUPPORT

BRACKET

FIGURE 3-3 Upper and Lower Jacket Latch

(Viewed from front of boiler)

Upper and Lower

Jacket Latch

Lift Jacket up,

engage jacket with chasis

push down.

FIGURE 3-2 Lower Jacket (Viewed from front of

boiler)

Disconnect connector

before removing Lower

Jacket

Lower Jacket

Connector to User

Interface

User Interface

Power Switch

8

3 - COMPONENT LISTING

FIGURE 3-4 Boiler Components (View from Front of Boiler)

GAS SHUTOFF

VALVE

(SHOWN IN OPEN

POSITION)

VENT CONNECTOR

COMBUSTION

AIR

BLOWER

GAS (CONTROL)

VALVE

LOW WATER

CUTOFF

HIGH TEMPERATURE

SUPPLY SWITCH

SAFETY RELIEF VALVE

AIR VENT

COMBUSTION

AIR INLET

NOTE:

See Section 5

For Piping

Instructions

HEAT EXCHANGER

PUMP

COMBUSTION

CHAMBER

CONDENSATE

COLLECTOR

RETURN WATER

FROM HEATING

SYSTEM (IN)

SUPPLY WATER TO

HEATING SYSTEM

(OUT)

LOW VOLTAGE

TERMINAL STRIP

CONTROL

MODULE

Fuse and

Holder

IGNITER

FLAME

SENSOR

SIGHT

GLASS

GAS CONNECTION

CONDENSATE

DRAIN

COMBUSTION

ANALYSIS TEST

PORT

TRANSFORMER

HIGH VOLTAGE

JUNCTION BOX

HEAT EXCHANGER

BALL VALVE

RETURN WATER

SENSOR (Located

behind piping)

VENT TEMPERATURE

SENSOR (Located

behind gas line)

PRESSURE

TEST PORT

9

4 - LOCATING BOILER

FIGURE 4-1 Clearance to Combustible Materials

4.1 Boiler Location Considerations

Ambient room temperature always above 32°F (0°C) to •

prevent freezing of liquid condensate.

Approved for installation in closets. •

Protect gas ignition system components from water •

(dripping, spraying, rain, etc.) during operation and

service (circulator replacement, condensate trap, control

replacement, etc.).

Wall mounting. •

Wall must be plumb and capable of supporting boiler •

weight plus 60 lbs (28 kg). See Table 1.

Wall mounting. See section 4.2.•

Access to outdoors to meet minimum and maximum •

pipe lengths for combustion air and vent piping. See

section 6.

Disposal of condensate. See section 6.•

Drainage of water (or water - antifreeze solution) during •

boiler service or from safety relief valve discharge. See

section 5.

Access to system water piping, gas supply, and electrical •

service. See sections 5, 7 and 8.

Clearances to combustible materials and service •

clearances. See Table 2 and ﬁ gure 4-1.

Multiple Boilers can be wall mounted, placed side by •

side, or back to back.

TABLE 2: BOILER CLEARANCES

Dimension

Combustible

Materials

(1)

Service

(1)(2)

Model

050/075/100/

150/200

050/075/100/

150/200

Top (A)

0" (0 cm) 14" (36 cm)

Left Side (B)

0" (0 cm) 0" (0 cm)

Right Side (C)

0" (0 cm) 0" (0 cm)

Front (D)

0" (0 cm) 6" (16 cm)

Back (E)

0" (0 cm) 0" (0 cm)

Bottom (F)

0" (0 cm) 12" (32 cm)

Combustion Air/Vent

piping

0" (0 cm)

6" (16 cm)

Hot Water Piping

½" (1.3 cm) 6" (16 cm)

(1)

Required distances measured from boiler.

(2)

Service, proper operation clearance recommendation.

A

E

D

A

C

B

A

FLOOR

A

D

F

10

4.2 Prepipe supply and return water connections with

factory ﬁ ttings before wall mounting.

4.3 Wall Mounting

Mount boiler on wall using wall mounting bracket included

with unit.

Structure must be capable of supporting boiler weight •

plus 60 lbs (28 kg). See Table 1, page 2.

Wall mount bracket has 4 slots allowing mounting on •

two (2) wall studs spaced at 11½" to 16½" on center.

See ﬁ gure 4-2.

Boiler includes (4) 3/8" x 3" lag screws and (4) washers •

for attaching wall mount bracket to wood studs. Field

source appropriate fasteners for other wall constructions

(masonry, concrete).

Attach wall mount bracket level on wall.•

Boiler must engage with wall mount bracket. •

Avoid overhang on sides of wall mount bracket. Verify •

boiler bracket is centered on wall bracket. See ﬁ gure

4-2.

4 - LOCATING BOILER

FIGURE 4-2 Wall Mount Bracket Engaged with

Bracket on Boiler

Center brackets. Avoid

overhang on sides of wall

mount bracket.

CAUTION

Boiler weight exceeds 75 pounds (34 kg). Do not

lift boiler onto wall without assistance.

!

4 Slots for attaching Wall

Mount Bracket to Studs

11

5.1 General

Install piping in accordance with authority having jurisdiction.•

NOTICE

Use two (2) wrenches when tightening and ﬁ tting

to pipe boiler's threaded ﬁ ttings. Boiler's internal

piping can be damaged if subjected to excessive

torque.

Support system piping and safety relief valve discharge •

piping. Boiler's internal piping and wall mount bracket can

be damaged if subjected to excessive weight.

Size central heating pump (and domestic hot water pump, •

if used) for system requirements only. Heat exchanger

pump compensates for pressure drop through boiler

internal piping and heat exchanger.

Thoroughly clean and ﬂ ush system before connecting to •

boiler.

5.2 Special Conditions

System piping exposed to freezing conditions: Use •

inhibited proplyene glycol solutions certiﬁ ed by ﬂ uid

manufacturer for use with closed water heating system.

Do not use automotive or ethylene glycol.

Boiler installed above radiation level (or as required by •

authority having jurisdiction). Integral low water cutoff

provided in boiler. See page 6.

Boiler used in connection with refrigeration system. •

Install piping in parallel with boiler, with appropriate

valves to prevent chilled medium from entering boiler.

System piping connected to heating coils located in air •

handling unit exposed to refrigerated air circulation.

Install ﬂ ow control valves or other automatic means to

prevent gravity circulation of boiler water during cooling

cycle.

5.3 Safety Relief Valve and Air Vent

NOTICE

Boiler rated at 50 psig (345 kPa) maximum

allowable working pressure. Boiler provided with

30 psig (206 kPa) safety relief valve. Field source

safety relief valve for system pressures greater than

30 psig (206 kPa). Temperature Pressure Gauge

and Air Vent satisfactory for 30-50 psig (206-345

kPa) operation.

Install safety relief valve and air vent using pipe ﬁ ttings •

provided with boiler. See ﬁ gure 5-1

Install safety relief valve with spindle in vertical position.•

Do not install shutoff valve between boiler and safety •

relief valve.

WARNING

Poison hazard. Ethylene glycol is toxic. Do not •

use ethylene glycol.

Never use automotive or standard glycol antifreeze, •

even ethylene glycol made for hydronic systems.

Ethylene glycol can attack gaskets and seals used •

in hydronic systems.

Use only inhibited proplyene glycol solutions •

certiﬁ ed by ﬂ uid manufacturer as acceptable for

use with closed water heating system.

Thoroughly clean and ﬂ ush any system that used •

glycol before installing new Boiler.

Provide user with Material Safety Data Sheet •

(MSDS) on ﬂ uid used.

!

5 - HYDRONIC PIPING

NOTICE

Do not expose boiler and condensate piping to

freezing temperatures.

FIGURE 5-1 Safety Relief Valve & Air Vent (View

from front of boiler)

Air Vent

3/4" x 1/4" NPT

90° Elbow

Safety Relief

Valve

3/4"F x 3/4"M

NPT Tee

3/4" NPT

Close Nipple

3/4 NPT

Position Air Vent and Safety Relief Valve

to provide space for discharge piping.

12

Install discharge piping from safety relief valve. See •

ﬁ gure 5-2.

Use ¾" or larger pipe.•

Use pipe suitable for temperatures of 375°F (191°C) •

or greater.

Individual boiler discharge piping shall be independent •

of other discharge piping.

Size and arrange discharge piping to avoid reducing •

safety relief valve relieving capacity below minimum

relief valve capacity stated on rating plate.

Run pipe as short and straight as possible to location •

protecting user from scalding and properly drain

piping.

Install union, if used, close to safety relief valve outlet.•

Install elbow(s), if used, close to safety relief valve •

outlet and downstream of union (if used).

Terminate pipe with plain end (not threaded).•

5.4 Trim Piping

Temperature - Pressure Gauge. Install temperature •

pressure gauge using nipple, tee and bushing provided

with boiler. See ﬁ gure 5-3.

Drain Valve. Install drain valve using nipple, tee and •

bushing provided with boiler. See ﬁ gure 5-3.

5.5 System Piping

Systems with automatic ﬁ ll valves require back ﬂ ow •

prevention device.

Single boiler system. See ﬁ gures 5-4, 5-5, 5-6, 5-7 for •

general guidance. Additional considerations:

Control system designed for single central heating •

pump. Installer responsible for integration of

multiple central heating pumps.

Control system allows domestic hot water •

prioritization. Function could be lost if central

heating pump not directly connected to control

system.

Multiple boiler system. See ﬁ gure 5-8 for general •

guidance. Additional considerations:

Control system requires equivalent water •

temperatures entering each boiler to properly

sequence and adjust system supply temperature.

Install multi boiler sensor kit. See "Parts, Kits & •

Optional Accessories" manual for part number.

5 - HYDRONIC PIPING

FIGURE 5-3 Temperature Pressure Gauge and

Drain Valve Installations

Temperature Pressure

Gauge shown at

System Supply

Connection

Check Local Codes

For Maximum

Distance To Floor

WARNING

Burn and scald hazard. Safety relief valve could

discharge steam or hot water during operation.

Install discharge piping per these instructions.

!

FIGURE 5-2 Safety Relief Valve Discharge Piping

Drain Valve shown

at System Return

Connection to Boiler

Safety Relief Valve

Gas Supply

13

Piping Legend

FIGURE 5-4 System Piping

5 - HYDRONIC PIPING

NOTICE

Illustrations are meant to show system piping

concept only. Installer responsible for all equipment

and detailing required by authority having

jurisdiction.

Check Local Codes

For Maximum

Distance To Floor

System

Return

System

Supply

FLOOR

Safety Relief Valve

14

5 - HYDRONIC PIPING

5-5 TWO-PIPE ZONED SYSTEM WITH VALVES

5-6 TWO-PIPE ZONED SYSTEM WITH PUMPS

Heat exchanger

ball valve open

(as shipped)

Heat exchanger

ball valve open

(as shipped)

DHW

Pump

CH/System

Pump

DHW

Pump

Zone

Pump

3/8"/10mm

Open End

Wrench

3/8"/10mm

Open End

Wrench

15

5 - HYDRONIC PIPING

5-7A SINGLE BOILER USING PRIMARY/SECONDAY PUMPING

12"/305mm Max. apart

12"/305mm

Max. apart

Limit length

to

5'/1.6 m

CH/System

Pump

Heat exchanger

ball valve open

Heat exchanger

ball valves closed

3/8"/10mm Open

End Wrench

5-7B SINGLE BOILER USING PRIMARY/SECONDAY PUMPING

CH/System

Pump

12"/305mm

Max. apart

12"/305mm Max. apart

Existing closely spaced tees

in primary system loop

Limit length

to

5'/1.6 m

3/8"/10mm Open

End Wrench

Existing closely spaced tees

in primary system loop

16

5 - HYDRONIC PIPING

5-8 TYPICAL MULTIPLE BOILER PIPING - (See Multiple Boiler Guide)

CH/

System

Pump

12"/305mm Max. apart

System

Temperature

Sensor

Size common piping

according to

maximum heat

capacity of

entire system

Up to 16

boilers

All heat exchanger

ball valves closed

3/8"/10mm Open

End Wrench

DHW

Pump

(See Multiple Boiler Guide)

17

6.1 General

This boiler requires a dedicated direct vent system.

Install combustion air and vent piping in accordance

with these instructions, authority having jurisdiction,

and

National Fuel Gas Code, ANSI 223.1/NFPA 54.

Vent connections serving appliances vented by natural draft

shall not be connected into any portion of mechanical draft

systems operating under positive pressure.

Install vent system in accordance with these instructions.

6.2 Removal of Existing Boiler From Common

Vent System

When existing boiler is removed from common venting

system, common venting system is likely to be too large for

proper venting of appliances remaining connected to it.

After removal of existing boiler, following steps shall

be followed with each appliance remaining connected to

common venting system placed in operation, while other

appliances remaining connected to common venting system

are not in operation:

Seal any unused openings in common venting system.•

Visually inspect venting system for proper size and •

horizontal pitch. Determine there is no blockage or

restrictions, leakage, corrosion and other deﬁ ciencies

which could cause an unsafe condition.

When practical, close all building doors, windows, and •

all doors between space in which appliances remaining

connected to common venting system are located and

other spaces of building. Turn on clothes dryer and any

appliance not connected to common venting system.

Turn on exhaust fans, such as range hoods and bath-

room exhaust so they will operate at maximum speed.

Do not operate summer exhaust fan. Close ﬁ replace

dampers.

Turn on appliance being inspected. Follow lighting •

instructions. Adjust thermostat so appliances will operate

continuously.

Test for spillage at draft hood relief opening after 5 •

minutes of main burner operation. Use ﬂ ame of match or

candle, smoke from cigarette, cigar or pipe.

Determine each appliance remaining connected to •

common venting system properly vents when tested

as outlined above. Then return doors, windows,

exhaust fans and any other gas-burning appliance to

their previous condition of use.

6 - COMBUSTION AIR AND VENT PIPING

Any improper operation of common venting system •

should be corrected so installation conforms with National

Fuel Code, ANSI Z223.1/NFPA 54. When re-sizing any

portion of common venting system, common venting

system should be re-sized to approach minimum size as

determined using appropriate tables in Chapter 13 of the

National Fuel Gas Code, ANSI Z223.1/NFPA 54.

6.3 Materials

See Table 3•

Table 3 - Combustion air and vent pipe ﬁ ttings

must conform with the following:

Item Material Standards

Vent Pipe

and Fittings

PVC schedule 40 ANSI/ASTM D1785

PVC - DWV ANSI/ASTM D2665

CPVC schedule 40

ANSI/ASTM D1784/

F441

SDR-21 & SDR-26 PVC ANSI/ASTM D2241

ABS-DWV ANSI/ASTM D2661

Schedule 40 ANSI/ASTM F628

Pipe

Cement/

Primer

PVC ANSI/ASTM D2564

CPVC ANSI/ASTM F493

Schedule 40 ABS ANSI/ASTM D2235

IPEX is approved vent manufacturer in Canada listed •

to ULC-S636.

IPEX System 636 Cements and Primers are approved •

in Canada listed to ULC-S636.

DO NOT USE CELLULAR (FOAM) CORE PIPE

WARNING

Use of cellular core PVC for venting ﬂ ue gas could

result in death, serious injury.

!

18

6 - COMBUSTION AIR AND VENT PIPING

WARNING

Vent extending through exterior wall shall not

terminate adjacent to wall or below building

extensions such as eaves, balconies, parapets or

decks. Failure to comply could result in death or

serious injury.

!

6.4 Pipe Installation

Minimum and maximum combustion air and vent pipe •

lengths listed in Table (4). Pipe length counted from

combustion air connector to termination.

Install ﬁ eld-sourced 2" to 3" transition, if used, in vertical •

section at combustion air inlet and vent connector.

90° elbows equivalent to 5.0 ft (1.6 m). 45° elbows •

equivalent to 3.5 ft (1.1 m). 2" to 3" transition has no

equivalent length.

Slope vent pipes minimum 1/4" per foot (21 mm/m) •

back toward boiler. Support horizontal sections to

prevent sags capable of accumulating condensate.

Support piping in accordance with pipe manufacturer's •

instruction and authority having jurisdiction. In absence

of manufacturer's instruction use pipe hooks, pipe

straps, brackets, or hangers of adequate and strength

located at intervals of 4 ft (1.2m) or less. Allow for

expansion/contraction of pipe.

Combustion air and vent piping must be air tight and •

water tight.

Certiﬁ ed vent system components must NOT be •

interchanged with other vent systems or unlisted pipe/

ﬁ ttings.

6.5 Termination

Terminate combustion air and vent pipes with ﬁ ttings or •

concentric vent kit.

See "Parts, Kits and Optional Accessories" manual •

for concentric vent kit part numbers.

Use horizontal pipe for vent and 90° elbow for •

combustion air termination when using ﬁ ttings.

Terminate combustion air and vent pipes in same •

atmospheric pressure zone through exterior sidewall or

roof.

Locate combustion air termination as far as possible •

from swimming pool, swimming pool pump house, and

other sources of airborne chlorine.

Locate combustion air and vent terminals as required by •

authority having jurisdiction.

Combustion Air and Vent Pipe Equivalent Length

2” Pipe 3” Pipe

Model 050 075/100 075/100 150/200

Min.

6 ft.

(1.8 m)

6 ft.

(1.8 m)

6 ft.

(1.8 m)

6 ft.

(1.8 m)

Max.

100 ft.

(30.5 m)

50ft.

(15.2 m)

100 ft.

(30.5 m)

100 ft.

(30.5 m)

1 - 90° elbow = 5 ft (1.6 m)

1 - 45° elbow = 3.5 ft (1.1 m)

1- 2" x 3" adapter = 0 ft (0 m)

Note: Concentric Vent Kit=5 ft (1.6m) equivalent length

Table 4 - Combustion Air and Vent Piping Length

For Example: Boiler can be installed on outside wall and vented with

1-90° elbow and 1 ft (0.30 m) of vent pipe.

19

6 - COMBUSTION AIR AND VENT PIPING

Side Wall

Terminations

y 3" (8 cm) Minimum horizontal

separation between combustion air

intake and vent terminations.

y 8" (21 cm) Minimum vertical

separation between combustion air

intake and vent terminations.

y 12" (30 cm) Separation between

bottom of combustion air intake and

bottom of vent.

y Multiple terminations as shown in

6-1, 6-2, and 6-3 must be a minimum

of 12” (30 cm) horizontally between

vent of one termination and air intake

of next appliance.

y Maximum allowable total outside

exposure vent length equals 10 ft.

(3.05m).

y Maintain a pitch of 1/2" per ft.

(42mm/m) outside exposure back to

boiler to ensure proper condensate

drainage for horizontal runs.

Roof

Terminations

y 3" (8 cm) Maximum horizontal

separation between combustion air

intake and vent of same appliance.

y 8" (21 cm) Minimum vertical

separation between combustion

air intake and vent of different

appliances.

y 15" (38 cm) Maximum horizontal

length of vent.

y Maximum vent/intake between

different appliances 12" (30cm).

y Maximum allowable total vertical

vent length with outside exposure is

10 ft.(3.05m).

y Abandoned unused masonry

chimney may be used as chaseway

for combustion air and vent. Both

combustion air and vent pipe must

exit above top of chimney with

clearances as shown in Figure 6-1.

12" (30 cm)

Minimum

8" (21 cm)

Minimum

15" (38 cm)

Maximum

3" (8 cm)

Maximum

Vent Combustion

Air

12" (30 cm)

Minimum above

anticipated snow line

Vent

3" (8 cm)

Maximum

separation

12" (30 cm)

Minimum from

overhang

12" (30 cm) Separation

between bottom of

combustion air intake

and bottom of vent

See snow & ice

page 23

Combustion Air

Vent

12" (30cm)

Minimum

separation

See snow & ice

page 23

FIGURE 6-1

FIGURE 6-2

FIGURE 6-3

Combustion Air

Roof Line

20

1"(2.54cm)

Maximum

Combustion

Air

Vent

6 - COMBUSTION AIR AND VENT PIPING

FIGURE 6-4

Maintain 12"

clearance above

highest anticipated

snow level or grade

* See Note

Below

Vent

Combustion

Air

1" (2.54cm)

Maximum

Roof overhang

36"(0.9m) Minimum

Maintain 12"(30cm)

clearance above highest

anticipated snow level or

grade

12" (30cm) Minimum

FIGURE 6-5

*Must be less than 4" or greater than 24" Horizontal dis-

tance between end bells of each air intake to prevent ﬂ ue

gas recirculation.

FIGURE 6-7

46-3/4" (1.2 m)

Vent

Combustion Air

1"(2.54cm)

Maximum

**See

Note

*2 or 3" (5.0 or 7.6cm) Diameter

PVC intake/combustion air

Elbow ﬁ eld

supplied

Combustion Air

Note: Securing strap must

be ﬁ eld installed to prevent

movement of termination

kit in side wall

*2" (

5.0cm)

Diameter = 41" Length (1.0m))

3" (7.6cm) Diameter = 47" Length (1.2m)

** Note Overall length may be modiﬁ ed by cutting or

extending both combustion air and vent pipes. 12" is

minimum allowable length and 60" is maximum allowable

length for this dimension. SDR-26 PVC (D2241) only may

be used for extending pipes. Do not use Schedule 40 PVC

or use couplings to extend pipes. Dimension will change if

intake/vent pipes are lengthened or shortened.

1" (2.54cm)

Maximum

OD 3½" (

8.9cm)

- *2" (

5.0cm)

kit

OD 4½" (11.4cm) - 3" (7.6cm)

kit

* Note: 2" For use with models 050/075/100.

3" For use with models 075/100/150/200

Page is loading ...

Dunkirk Helix VLT Vertical Laser Tube, Wall Hung Modulating Condensing Boiler Installation, Operation & Maintenance Manual

This manual is also suitable for

Dunkirk Helix VLT Vertical Laser Tube, Wall Hung Modulating Condensing Boiler Installation, Operation & Maintenance Manual

Related papers

Other documents