Revision A
P/N E242557
www.elotouch.com
Quick Installation Guide
Elo M60 Mobile Computer
© 2021 Elo Touch Solutions, Inc. All rights reserved.
The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Affiliates (collectively “Elo”) makes no
representations or warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a
particular purpose. Elo reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation
of Elo to notify any person of such revisions or changes.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer
language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior
written permission of Elo Touch Solutions, Inc.
Elo and the Elo logo are either trademarks or registered trademarks of Elo Touch Solutions, Inc..
America
800-ELO-TOUCH
Tel +1 408 597 8000
Europe (EMEA)
Tel +32 16 930 136
Asia Pacific
Tel +86 (21) 3329 1385
Elo Technical Support
Online self-help: www.elotouch.com/support
Contents:
• Elo M60 Mobile Computer
• 18W AC-DC Adapter
• US/EU/UK Adapter plugs
Battery removal
Battery replacement
1. Remove the top over by
pulling up from notched area.
1. Slide battery under ledge at
front and tilt down at back side.
2. Remove screws (x3)
3. Pull door off.
2. Replace door.
3. Replace screws (x3)
Ambient Light Sensor
Camera and Flash
Function LED
SCR Slot
Power LED
Contactless pay area
(graphic on screen)
Power Button
MSR track
I/O Connector
USB-C
Function Button
Volume Down
Function Button
Volume Up
4. Tilt battery up at bottom
side and pull back to release
battery connector.
4. Replace the top cover.
Micro SD/Nano Sam card installation
1. Remove battery.
2. Pull out Micro SD card/Nano SAM holder.
3. Place SD cadr/Nano SAM with contacts facing down.
4. Replace holder.
Micro SD Nano SAM
Battery connector
Press down
on battery
connector
Revision A
P/N E242751
www.elotouch.com
Quick Installation Guide
Elo M60C Mobile Computer
© 2021 Elo Touch Solutions, Inc. All rights reserved.
The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Affiliates (collectively “Elo”) makes no
representations or warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a
particular purpose. Elo reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation
of Elo to notify any person of such revisions or changes.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer
language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior
written permission of Elo Touch Solutions, Inc.
Elo and the Elo logo are either trademarks or registered trademarks of Elo Touch Solutions, Inc..
America
800-ELO-TOUCH
Tel +1 408 597 8000
Europe (EMEA)
Tel +32 16 930 136
Asia Pacific
Tel +86 (21) 3329 1385
Elo Technical Support
Online self-help: www.elotouch.com/support
Contents:
• Elo M60C Mobile Computer
• 18W AC-DC Adapter
• US/EU/UK Adapter plugs
Battery removal
Battery replacement
1. Remove the top over by
pulling up from notched area.
1. Slide battery under ledge at
front and tilt down at back side.
2. Remove screws (x3)
3. Pull door off.
2. Replace door.
3. Replace screws (x3)
Ambient Light Sensor
Camera and Flash
Function LED
SCR Slot
Power LED
Contactless pay area
(graphic on screen)
Power Button
MSR track
I/O Connector
USB-C
Function Button
Volume Down
Function Button
Volume Up
4. Tilt battery up at bottom
side and pull back to release
battery connector.
4. Replace the top cover.
Micro SD/Nano Sam card + Nano SIM card Installation
1. Remove battery.
2. Pull out Micro SD card/Nano SAM + Nano SIM holder.
3. Place SD cadr/Nano SAM and/or Nano SIM with contacts facing down.
4. Replace holder.
Micro SD
Nano SIM
Nano SAM
Battery connector
Press down
on battery
connector
Revision A
P/N E509981
www.EloTouch.com
Quick Installation Guide
Elo M60S Mobile Computer
© 2022 Elo Touch Solutions, Inc. All rights reserved.
The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Affiliates (collectively “Elo”) makes no
representations or warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a
particular purpose. Elo reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation
of Elo to notify any person of such revisions or changes.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer
language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior
written permission of Elo Touch Solutions, Inc.
Elo and the Elo logo are either trademarks or registered trademarks of Elo Touch Solutions, Inc.
America
Tel +1 408 597 8000
Europe (EMEA)
Tel +32 16 930 136
Asia Pacific
Tel +86 (21) 3329 1385
Learn more about Elo at EloTouch.com
Contents:
• Elo M60S Mobile Computer
• 18W AC-DC Adapter
• US/EU/UK Adapter plugs
Micro SD/Nano Sam card installation
1. Remove battery.
2. Pull out Micro SD card/Nano SAM holder.
3. Place SD card/Nano SAM with contacts facing down.
4. Replace holder.
Micro SD Nano SAM
Battery removal
Battery replacement
1. Remove the top over by
pulling up from notched area.
1. Slide battery under ledge at
front and tilt down at back side.
2. Remove screws (x3)
3. Pull door off.
2. Replace door.
3. Replace screws (x3)
Ambient Light Sensor
Camera and Flash
Function LED
SCR Slot
Power LED
Contactless pay area
(graphic on screen)
Power Button
MSR track
I/O Connector
USB-C
Function Button
Volume Down
Function Button
Volume Up
4. Tilt battery up at bottom
side and pull back to release
battery connector.
4. Replace the top cover.
Battery connector
Press down
on battery
connector
Scan trigger button
Scan trigger button
Revision A
P/N E510176
www.EloTouch.com
Quick Installation Guide
Elo M60SC Mobile Computer
© 2022 Elo Touch Solutions, Inc. All rights reserved.
The information in this document is subject to change without notice. Elo Touch Solutions, Inc. and its Affiliates (collectively “Elo”) makes no
representations or warranties with respect to the contents herein, and specifically disclaims any implied warranties of merchantability or fitness for a
particular purpose. Elo reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation
of Elo to notify any person of such revisions or changes.
No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer
language, in any form or by any means, including, but not limited to, electronic, magnetic, optical, chemical, manual, or otherwise without prior
written permission of Elo Touch Solutions, Inc.
Elo and the Elo logo are either trademarks or registered trademarks of Elo Touch Solutions, Inc.
America
Tel +1 408 597 8000
Europe (EMEA)
Tel +32 16 930 136
Asia Pacific
Tel +86 (21) 3329 1385
Learn more about Elo at EloTouch.com
Contents:
• Elo M60SC Mobile Computer
• 18W AC-DC Adapter
• US/EU/UK Adapter plugs
Battery removal
Battery replacement
1. Remove the top over by
pulling up from notched area.
1. Slide battery under ledge at
front and tilt down at back side.
2. Remove screws (x3)
3. Pull door off.
2. Replace door.
3. Replace screws (x3)
Ambient Light Sensor
Camera and Flash
Function LED
SCR Slot
Power LED
Contactless pay area
(graphic on screen)
Power Button
MSR track
I/O Connector
USB-C
Function Button
Volume Down
Function Button
Volume Up
4. Tilt battery up at bottom
side and pull back to release
battery connector.
4. Replace the top cover.
Micro SD/Nano Sam card + Nano SIM card Installation
1. Remove battery.
2. Pull out Micro SD card/Nano SAM + Nano SIM holder.
3. Place SD card/Nano SAM and/or Nano SIM with contacts facing down.
4. Replace holder.
Micro SD
Nano SIM
Nano SAM
Battery connector
Press down
on battery
connector
Scan trigger button
Scan trigger button
/