Havis DS-DA-806 Installation guide

Havis
Brand
Havis
Model
DS-DA-806
Category
Car kits
Type
Installation guide
A
REAR FENCE
DS-DELL-400
(SOLD SEPARATELY)
DS-DA-806
DETAIL A
SCALE 2 : 1
TORX FLAT HEAD
(T15)
CABLE STRAIN
RELIEF HOLES
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
PRODUCT I.D.
DATE
WEIGHT: (LBS)
SCREEN BLANKING SYSTEM WITH
PORT COVER FOR DS-DELL-400
SERIES DOCKING STATIONS
03/14/2016
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
PRODUCT I.D.
DATE
WEIGHT: (LBS)
DS-DA-806_INST_3-16
PRODUCT DESCRIPTION
"BLANK-IT" SCREEN BLANKING DONGLE WITH PORT COVER
FOR DS-DELL-400 SERIES DOCKING STATIONS
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
PRODUCT I.D.
DATE
WEIGHT: (LBS)
PRODUCT NAME
REV. DATE
DRAWING NUMBER:
DS-DA-806
INSTALLATION INSTRUCTIONS:
NOTE:
-DOCKING STATION DEPICTED MAY NOT MATCH IDENTICALLY
TO PRODUCT PURCHASED. HOWEVER, ALL INSTALLATION
INSTRUCTIONS ARE STILL APPLICABLE UNLESS OTHERWISE
NOTED.
1. FIRST CONNECT AND ROUTE ALL OTHER CABLES NEEDED
FOR YOUR SPECIFIC APPLICATION. PLUG IN THE BLANK-IT
USB DONGLE INTO THE USB PORT THAT IS ADJACENT TO THE
HDMI PORT.
2. REMOVE THE (QTY:2) REAR FENCE USING A TORX T15 BIT.
2. POSITION PORT COVER BRACKET INTO PLACE ON DS-
DELL-400 SERIES DOCKING STATION, AS SHOWN IN
ILLUSTRATION. BE CAREFUL NOT TO PINCH ANY CABLES
BETWEEN THE PORT COVER AND DOCKING STATION.
3. IF THIS DOCKING STATION WILL NOT BE USING A SCREEN
SUPPORT, THEN FASTEN THE TORX FLAT HEAD SCREW (T15)
TROUGH THE REAR FENCES, THROUGH THE PORT BLOCKER
BRACKET, AND INTO THE THREADED INSERTS OF THE DS-
DELL-400 SERIES DOCKING STATION. AS SEEN ON PAGE 1.
4. IF THIS DOCKING STATION WILL BE USING A SCREEN
SUPPORT (AS SEEN ON PAGE 2). FASTEN THE PHILLIPS FLAT
HEAD SCREWS (PH2) THROUGH THE MOUNT HOLES OF THE
REAR FENCE, THEN THROUGH THE HOLES IN THE SCREEN
SUPPORT, THEN THROUGH THE HOLES OF THE PORT
BLOCKER BRACKET AND INTO THE THREADED INSERTS OF
THE DOCKING STATIONS MAIN PLATE. AS SEEN IN THE
ILLUSTRATIONON PAGE 2.
5. PROPERLY STRAIN RELIEVE ALL CABLES WITH ZIP TIES.
USING THE CABLE STRAIN RELIEF HOLES IN THE PORT
BLOCKER BRACKET
6. FASTEN DOCKING STATION ASSEMBLY TO HAVIS
APPROVED MOUNT USING DOCKING STATION MOUNTING
HARDWARE (PROVIDED WITH DS-DELL-400 SERIES DOCKING
STATION)
.
WARNING: ALL HAVIS INC. PRODUCTS ARE DESIGNED WITH SAFETY OF USE AND INSTALLATION IN MIND. HOWEVER,
IT IS THE SOLE RESPONSIBILITY OF THE OWNER/OPERATOR OF A VEHICLE USING HAVIS INC. MOUNTING AND
DOCKING EQUIPMENT, TO INSURE THAT THE EQUIPMENT IS INSTALLED SO THAT IT WILL NOT INTERFERE WITH VEHICLE
OPERATION, INTERFERE WITH SAFETY DEVICES, OBSTRUCT VIEW OF DRIVING CONDITIONS, OR IN ANY WAY
DEGRADE OCCUPANT SAFETY. IMPROPER INSTALLATION CAN CAUSE SERIOUS INJURY IN THE EVENT OF AN
ACCIDENT. INSTALLATION SHOULD ONLY BE PERFORMED BY QUALIFIED PROFESSIONALS. COMPUTERS AND
MOTION DEVICES MUST BE MOVED TO AND STOWED/SECURED IN THEIR SAFE DRIVING POSITIONS BEFORE
OPERATING VEHICLE.
5.35
WWW.HAVIS.COM
1-800-524-9900
F-730-019 REV A
B
DETAIL B
SCALE 2 : 1
PHILLIPS FLAT HEAD
PH2
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
PRODUCT I.D.
DATE
WEIGHT: (LBS)
SCREEN BLANKING SYSTEM WITH
PORT COVER FOR DS-DELL-400
SERIES DOCKING STATIONS
03/14/2016
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
PRODUCT I.D.
DATE
WEIGHT: (LBS)
DS-DA-806_INST_3-16
PRODUCT DESCRIPTION
"BLANK-IT" SCREEN BLANKING DONGLE WITH PORT COVER
FOR DS-DELL-400 SERIES DOCKING STATIONS
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
PRODUCT I.D.
DATE
WEIGHT: (LBS)
PRODUCT NAME
REV. DATE
DRAWING NUMBER:
DS-DA-806
WARNING: ALL HAVIS INC. PRODUCTS ARE DESIGNED WITH SAFETY OF USE AND INSTALLATION IN MIND. HOWEVER,
IT IS THE SOLE RESPONSIBILITY OF THE OWNER/OPERATOR OF A VEHICLE USING HAVIS INC. MOUNTING AND
DOCKING EQUIPMENT, TO INSURE THAT THE EQUIPMENT IS INSTALLED SO THAT IT WILL NOT INTERFERE WITH VEHICLE
OPERATION, INTERFERE WITH SAFETY DEVICES, OBSTRUCT VIEW OF DRIVING CONDITIONS, OR IN ANY WAY
DEGRADE OCCUPANT SAFETY. IMPROPER INSTALLATION CAN CAUSE SERIOUS INJURY IN THE EVENT OF AN
ACCIDENT. INSTALLATION SHOULD ONLY BE PERFORMED BY QUALIFIED PROFESSIONALS. COMPUTERS AND
MOTION DEVICES MUST BE MOVED TO AND STOWED/SECURED IN THEIR SAFE DRIVING POSITIONS BEFORE
OPERATING VEHICLE.
5.35
WWW.HAVIS.COM
1-800-524-9900
F-730-019 REV A
  • Page 1 1
  • Page 2 2

Havis DS-DA-806 Installation guide

Havis
Brand
Havis
Model
DS-DA-806
Category
Car kits
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents