Munters Wall Mount Fan Owner's manual

Brand: Munters

Model: Wall Mount Fan

Type: Owner's manual

This manual is also suitable for

WM36K Single

Munters WM36K Single is a high-performing, high-quality Wall Mount Fan with Damper Door which can be used to ventilate and circulate air in a variety of settings. Its robust construction and powerful motor make it suitable for heavy-duty applications.

The fan features a durable fiberglass construction with a damper door that can be adjusted to control airflow. It has a belt-driven system with a V-belt and 3” idler pulley, providing smooth and efficient operation. The fan also includes a motor mount stiffener bracket, ensuring stability and reducing vibration during operation.

The WM36K Single comes with a motor base bracket and belt tensioner bracket for easy installation and maintenance. It has a 115/230 VAC or 208-230/460 VAC power supply, and it can operate at both 60Hz and 50Hz.

1© Munters Corporation, August 2021 QM1231r10

Instruction Manual

WM Fiberglass Wall Mount Fan

with Damper Door - 1-Pack Quick Kit

Models: WM36xKxCB

WM36K

Wall Mount Fan

with Damper Door

1-Pack Quick Kit

2QM1231r10

Thank You:

Thank you for purchasing a Munters Wall Mount Fan with Damper. Munters equipment is designed to be the

highest performing, highest quality equipment you can buy. With the proper installation and maintenance it will

provide many years of service.

Please Note:

To achieve maximum performance and insure long life from your Munters product it is essential that it be installed

and maintained properly. Please read all instructions carefully before beginning installation.

Warranty:

For Warranty claims information see the “Warranty Claims and Return Policy” form QM1021 available from the

Munters Corporation office at 1-800-227-2376 or by e-mail at [email protected].

Conditions and Limitations:

• Products and Systems involved in a warranty claim under the “Warranty Claims and Return Policy” shall have

been properly installed, maintained and operated under competent supervision, according to the instructions

provided by Munters Corporation.

• Malfunction or failure resulting from misuse, abuse, negligence, alteration, accident or lack of proper installation

or maintenance shall not be considered a defect under the Warranty.

WM36K Fiberglass Wall Mount Fan with Damper

Instructions for Use and Maintenance

3© Munters Corporation, August 2021 QM1231r10

Index

Chapters Page

1. Unpacking the Equipment 4

1.1 Parts List 4

1.2 Fan Dimensions 6

1.3 Tools for Installation 6

2. Installation Instructions 7

2.1 Wall Framing 7

2.2 Fan Assembly 8

2.3 Cone Installation 12

2.4 Motor Mounting 16

3. Electrical Wiring 22

3.1 Recommended Wiring 23

4. Operation 24

5. Maintenance 25

6. Winterizing 27

6.1 Winterizing 27

6.2 Winter Weather Protection 27

7. Troubleshooting 28

8. Exploded View and Parts List 29-31

4QM1231r10

1.1 Parts List

Unpacking the Equipment 1.

Each Crate Includes

1 – 36” Orifice Panel, Fiberglass Fan, Sub-Assembly

1 – Motor

1 – Drip Shield, AL

4 – Cone Sections, PL

1 – Cone Guard

1 – Inlet Guard

4 – Cone/Strut Mounting Brackets, GZ

1 – Motor Mount Stiffener Bracket, GZ

1 – Bulk Parts Package (BK1149)

BK1149 – Bulk Parts Package for WM36K

1 – Motor Base Bracket, CTD-GZ

1 – Belt Tensioner Bracket, CTD-GZ

1 – Motor Sheave, C.I.

1 – V-Belt, A-Section

1 – 3” Idler Pulley, A-Section C.I., Blue

1 – Rotary Tensioner Arm, AL

1 – Hardware Package (HP1177)

1 – Coated Cable with Ferrule, 100”L.

5© Munters Corporation, August 2021 QM1231r10

Unpacking the EquipmentChapter 1

[A]

[B]

[C]

[D]

[E]

[F]

[G]

[H]

[J]

[K]

[L]

[M]

[N]

HP1177 – Hardware Package for 1 – WM36K

ID Qty. Cat. No. Description

[A] 2 KW3011 5⁄16” x 1¼ ”O.D. Flat Washer, SS

[B] 1 KS1931 M10-1.5 x 25mm Hex Bolt, ZP

[C] 1 KW3509 10mm Splitlock Washer, ZP

[D] 16 KS1007 5⁄16” x 1.25” Hex Head Bolts, SS

[E] 4 KS1029 5⁄16” x 1.75” Hex Head Bolts, SS

[F] 3 KS1075 5⁄16” x 2.75” Hex Head Bolts, SS

[G] 31 KN0704 5⁄16” SRTD Flange Nuts, SS

[H] 1 KS2463 1⁄4” x1.5” HEX Lag Screw,ZP

[J] 1 AC0211 & AC0212 Azuma Bolt & Nut, Blue PL

[K] 1 KS1046 M10-1.5 x 50mm Hex bolt, ZP

[L] 8 FH1968 1-Hole Pivoting Shutter Clip, BLK PL

[M] 2 AC1381 1⁄8” Dia. Cable Clamp, ZP

[N] 2 KX1158 Hole Plug, 0.73”-0.76” Dia., BLK PL

6QM1231r10

1.2 Fan Dimensions

Fan Specifications: 60Hz shown (50Hz available)

Power: 115/230 VAC* or 208-230/460 VAC

Phase: 1 or 3

*Available voltages vary depending on HP

Unpacking the EquipmentChapter 1

1.3 TOOLS REQUIRED FOR INSTALLATION

10mm [3⁄8”] Socket

13mm [½”] Socket

17mm [11⁄16”] Socket or Wrench

27mm [11⁄16”] Wrench

7⁄16” Socket

Phillips Screwdriver, #3 Size

5⁄32” Hex Wrench

Wire Cutting Pliers

Dimensions:

Size A B C* D - Dia. E F Wall Openings

36” 48”W. x 48”H. 40” 59⁄16”48

3⁄8”2”1

13⁄16”44

1⁄2”W. x 441⁄2”H.

Wall Opening (W.O.)

D - Dia.

Guard

*Dimension varies depending on wall construction and motor configuration.

7© Munters Corporation, August 2021 QM1231r10

2.1 Wall Framing

Step 1

Construct framed opening to correct size according to the Wall Opening listed in Chart A below.

See Figure 1A and 1B. When installing exterior sheet metal before fan, leave 2” of the framing exposed on all

sides so the orifice can mount flush to the frame.

Installation Instructions 2.

Minimum Spacing

'Z'

Chart A

Wall Opening

(W. x H.)

Fan Dia.

12” recommended; 3½” minimum

36” 44½” W. x 44½” H.

Center To Center

Dimension

48” Minimum

Figure 1B 4 x 4 Post Construction - Elevation View

Ceiling

Framing

(See chart A)

12"

(See chart A)

See minimum

spacing notes in

Chart A

2 x 8 Header boards

4 x 4 or

4 x 6 Posts

2 x 4

Framing

2 x 8 Banner boards

Ceiling

4 x 4 or 4 x 6 Posts

(See chart A)

Figure 1A Frame Construction

441⁄2”W.

Top View

48”W. O.C.

W x H Wall Opening

Sheet Metal Opening

Stud Wall

8QM1231r10

Step 2A

Remove the BK1149 and Motor from the front of the crate. See Figure 2A.

Figure 2A

Installation InstructionsChapter 2

Step 2B

Remove all the other loose parts from the back of the crate. See Figure 2B.

Figure 2B

BK1149

Motor

The fan can either be installed on the wall before the drive system is installed or

the drive system can be installed while the fan is in the crate.

2.2 Fan Assembly

9© Munters Corporation, August 2021 QM1231r10

Step 3

Carefully turn the crate onto its side, so that the drain holes in the orifice are at the bottom. See Figure 3.

Drain Holes

Step 4

Attach the Motor Base Bracket and the Belt Tensioner Bracket to the Tube Strut using (3) Long Bolts [F], (2)

Washers [A] and (3) Nuts [G]. See Figure 4.

Figure 3

Figure 4

Installation InstructionsChapter 2

Bolt [F]

Washer [A]

Nuts [G]

Motor Base Bracket

Belt Tensioner Bracket

10 QM1231r10

Step 5

Attach the 3” Idler Pulley to the Tensioner Arm using Bolt [K]. Then attach the Tensioner/Pulley Assembly to

the Tensioner Bracket using Bolt [B] and Splitlock Washer [C]. Finger tighten only at this time. See Figure 5.

Figure 5

Installation InstructionsChapter 2

Bolt [B]

Splitlock Washer [C]

Tensioner Pulley

Tensioner Arm

Bolt [K]

Step 6

Attach Drip Shield to bottom of framed opening using (3) Barn Screws (Not Provided). See Figure 6A and 6B. If

a 4” wall is used a support board must be installed as shown in Figure 6B. Be sure not to deform Drip Shield when

installing screws.

Figure 6A

Barn Screw

(Not Provided)

Drip Shield

Figure 6B

Barn Screw

(Not Provided)

Drip Shield Drip Shield

Barn Screw

(Not Provided)

Support board

11© Munters Corporation, August 2021 QM1231r10

Installation InstructionsChapter 2

Step 7

Locate Drain holes in Orifice Panel. This is bottom of Fan. Set bottom edge of fan on Drip Shield ledge

and center panel on opening. Secure Fan to wall using (16) Barn Screws (Not Provided).

See Figure 7A and 7B.

Figure 7A

Step 8

Find Coated Cable and insert end opposite ferrule into small hole in upper plate of Main Frame. Pull

it through until ferrule stops at plate. See Figure 8.

Figure 8

Hole in Main Frame

Ferrule

Figure 7B

Latch Pin Oriﬁ ce panel

Barn Screw (Not Provided)

Drip Shield Ledge

12 QM1231r10

Step 9

Place all 4 cone sections on a flat surface with tabs from one facing slots of the next. See Figure 9A.

Curl up tab end of first cone section and insert tabs up into slots in the next cone section. A mallet may

be needed to seat slots over tabs completely. See Figure 9B. Repeat this until all 4 cone sections are

connected and laying flat.

Installation InstructionsChapter 2

Step 10A

Fasten each of the joints in the single outer hole using (1) Short Bolt [D] and Nut [G], with the nut on the

side with the tabs. At the inner pair of holes of each joint attach (1) Cone Support Bracket to the inner

hole using (1) Short Bolt [D] and Nut [G] with the bolt head on the side with the tabs. See Figure 10A.

Figure 9A

Figure 10A

Nut [G]

Figure 9B

Outer Hole Short Bolt [D]

Short Bolt [D]

Inner holes

Nut [G]

Cone Support Bracket

2.3 Cone Installation

13© Munters Corporation, August 2021 QM1231r10

Installation InstructionsChapter 2

Step 10B

Stand cone sections on end and curl ends around to form cone with Cone Support Bracket on outside and tabs

on inside. Insert remaining tabs into slots so tabs are inside cone and fasten final joint using (1) Short Bolt [D]

and Nut [G], with nut on inside of cone. At the inner pair of holes attach (1) Cone Support Bracket to the inner

hole using (1) Short Bolt [D] and Nut [G] with bolt head on inside of cone. See Figure 10B.

Short Bolt [D]

Cone Support Bracket

Nut [G]

Short Bolt [D]

Nut [G]

Figure 10B

14 QM1231r10

Installation InstructionsChapter 2

Figure 11A

Step 11A

Install cone onto fan by putting top of cone over top of fan. The hole in tab of one cone section should

slide down over the Frame Pin in the Main Frame assembly. Allow remainder of cone to slide over orifice

panel making sure Cone Support Brackets remain on outside of cone. See Figure 11A.

Frame Pin

Hole in Tab of Cone Section

Step 11B

Place end of Cone Support Bracket with slot over bolt holding Cone/Strut Mounting Bracket to the orifice

and secure with Nut [G]. See Figure 11B. Secure Cone to Fan installing Medium Bolt [E] through the

remaining hole in the Cone Support Bracket and fastening with Nut [G]. A long screwdriver may be

needed to help align the holes through Cone Support Bracket, Cone, Main Frame and Orifice. Repeat

process for all 4 Cone Support Brackets. See Figure 11B.

Figure 11B

Nut [G]

Medium Bolt [E]

Nut [G]

Use this hole for WM36F

Use this hole for WM54F

Installation InstructionsChapter 2

Step 12

Insert guard into cone with the eyelets facing you. Install eyelets over bolts already installed in cone and fasten

with Nut [G]. Secure remaining eyelets using Short Bolt [D] and Nut [G]. See Figure 12.

Nut [G]

Previously installed - Bolt and Nut

Step 13

Loop Coated Cable that was installed in a previous step, around the lower, middle joint in guard and fasten to

itself with Azuma Bolt & Nut [J]. Make sure cable is pulled snug. See Figure 13.

Figure 12

Figure 13

Azuma Bolt & Nut [J]

Short Bolt [D]

Coated Cable

Note:

When installing cable in

temperatures BELOW 60°F,

leave cable slightly slack

(do not overtighten).

16 QM1231r10

Installation InstructionsChapter 2

Motor Key

Motor

Motor Sheave

Step 15

Find the Key provided with the Motor and place it in the Keyway on the motor shaft. Place the Motor

Sheave on the Motor shaft with the hub facing towards the motor. See Figure 15. ONLY tighten the set

screw enough to hold the Sheave in place at this time. See Figure 15.

Figure 15

2.4 Motor Mounting

Note:

When wiring motor, check rotation of propeller.

Internal wiring of motor may need to be changed

to assure proper rotation of propeller.

Step 14

If Fans are to be installed 60” O.C., cut the 3 o’clock and 9 o’clock guard wire in the position shown. Push

the side of the cone in as far as possible and fasten the cut guard wire to the attached guard wire using

Clamp [M]. See Figure 14.

Cut Guard Wire Here

Clamp [M]

Figure 14

Installation InstructionsChapter 2

Step 16

Set Motor on Motor Bracket so Motor base rests against lower Motor Bracket flange. Align middle and front

slots in Motor base with holes in Motor Bracket. See Figure 16.

Step 17A

Secure Motor to Motor Bracket and Motor Bracket Stiffener using (4) Short Bolts [D] and Nuts [G]. The

rear upper bolt is where Motor Bracket Stiffener is attached. See Figure 17A.

Figure 16

Stiﬀ ener

Short Bolts [D]

Nuts [G]

Figure 17A

Holes in Motor Bracket

Front and Middle Slots

Lower Motor Bracket Flange

18 QM1231r10

Step 18

Use a straight edge or level to check alignment of the

Propeller Sheave, Tensioner Pulley and the Motor Sheave.

If needed, adjust position of Motor Sheave so the 3 pulleys

line up. Once Motor Sheave is aligned tighten set screw to

75 in-lbs [9 N-m] torque. See Figure 18.

Figure 18

Level

Motor Sheave

Tensioner Pulley

Propeller Sheave

Installation InstructionsChapter 2

Figure 17B

Stiﬀ ener

Step 17B

Using channel locks and/or a hammer twist the Motor Bracket Stiffener so that the holes in the bracket lay

flat against the framing. Then secure the bracket to the framing using (1) Lag Screw [H]. See Figure 17B.

Framing

Lag Screw [H]

Installation InstructionsChapter 2

Step 19A

Slide V-belt over Propeller and install by wrapping it around 2 smaller pulleys and starting it over

larger Sheave. Continue rolling it onto the larger Sheave until it fits into groove. See Figure 19A.

If desired the 2 drain holes in the Orifice Panel can be plugged using (2) Hole Plugs [NN]

Figure 19A

Drain Holes

Step 19B

To adjust belt tensioner to proper setting, loosen 10mm bolt (using 17mm end wrench) to allow tensioner arm

to rotate. Working from inlet/motor side of fan, place a 27mm (11⁄16”) wrench onto the hex on the tensioner.

Turn wrench clockwise until the single mark on base of belt tensioner is aligned with Mark 3 on the tensioner

arm. Hold at this setting and tighten the 10mm bolt to 40 ft.lbs. [54 N-m] torque. See Figure 19B.

Figure 19B

Mark 3 on Tensioner Arm

Hex on Tensioner Arm

10mm Bolt

Single Mark on Base

20 QM1231r10

Installation InstructionsChapter 2

Step 20A

Cut a section of the inlet guard out to fit over the motor as shown below for the appropriate fan. When cutting

the guard wires make sure to cut them as close to the other wires as possible. See Figure 20A.

Figure 20A

10” 12”

12”

4”

48”

Page is loading ...

Munters Wall Mount Fan Owner's manual

Brand: Munters

Model: Wall Mount Fan

Type: Owner's manual

This manual is also suitable for

WM36K Single

Download PDF

report

Munters Wall Mount Fan Owner's manual

This manual is also suitable for

Munters Wall Mount Fan Owner's manual

Related papers

Other documents