BodyCraft R1000G Owner's manual

Category
Fitness, gymnastics & weight training
Type
Owner's manual
R1000g Recumbent Bike
1
CONGRATULATIONS! And THANK YOU for selecting the BODYCRAFT R1000g
Recumbent Bike! Your choice reflects a wise investment in you and your family’s
health and wellness. We hope you use it for many healthy years!
For your safety and benefit, please read this entire manual. Please keep the manual in a convenient
place for quick reference when needed.
BODYCRAFT offers a complete array of high quality fitness equipment. Please refer to our web site at
www.bodycraft.com to view more ways to enhance your lifestyle.
Your BODYCRAFT R1000g has all the quality and design elements to make your workout extremely
efficient and comfortable. Your new Recumbent Bike is a serious cardio fitness machine that will keep
you motivated, challenged and within reach of your fitness goals. The BODYCRAFT R1000g will
provide an efficient, low impact cardiovascular workout that will help improve energy levels and your
quality of life. Cardiovascular training is vital for all ages and the BODYCRAFT R1000g will provide an
effective workout, producing results that will encourage you to reach your fitness goals and maintain
the body you have always wanted. Spending 15 to 30 minutes a day, three times a week is all
youneed to start seeing the benefits of a regular exercise program.
As a premium exercise equipment manufacturer, we are committed to your complete satisfaction. If
you have questions, suggestions or find missing or damaged parts, we guarantee your complete
satisfaction through our authorized dealer network or by contacting us directly. Please call your local
dealer or BODYCRAFT.
Phone: 800-990-5556 9am - 5pm EST Email: [email protected]
Recreation Supply, Inc.
7699 Green Meadows Dr.
Lewis Center, OH 43035
Purchaser’s Reference Information:
IT IS IMPERATIVE THAT YOU FILL IN THE FOLLOWING
INFORMATION AND REFER TO IT SHOULD THE NEED
FOR SERVICE ARISE.
Product Name: R1000g Recumbent Bike
Serial Number: RB _ _ _ _ _ _ _ _ _ _ _ _
Proof of purchase must be supplied to validate warranty and the product must have been
registered with BODYCRAFT via online at www.bodycraft.com or by calling 800-990-5556 or
740-965-2442 M-F 9 a.m. - 5 p.m. EST.
2
TABLE OF CONTENTS
Product Safety ………………………….……………………………………………… 3
Product Assembly …………………………………………………………………….. 4
Hardware Identification Chart ………………………………………………………… 5
Assembly Parts ……………………………………………….……………………….. 6
Assembly Instructions ………………………………………………………………… 7
Operational Instructions …………………………………………............................. 12
Console Operation Instructions ……………………………………………………… 13
Warm Up and Cool Down …………………………………………………………….. 21
Part List ………………………………………………..……………………………….. 22
Exploded View ……………………………………….………………………………… 25
Product Warranty …………………………..………………………........................... 26
3
PRODUCT SAFETY
Basic precautions should always be followed, including the following safety
instructions when using this equipment:
WARNING: To reduce the risk of serious injury, read the following Safety Instructions
before using the Recumbent Bike.
1. It is recommended that you perform warm up exercises before using this equipment.
2. Please make sure all components are not damaged and in working order before use.
3. This equipment should be placed on a flat surface while in use. Using a mat or other
material on the ground is recommended.
4. Please wear proper clothes and shoes when using this equipment; do not wear clothes that
might catch in any part of the equipment.
5. Do not attempt any maintenance or adjustments other than those described in this manual.
Should any problems arise, discontinue use and consult an Authorized Service Representative.
6. Use caution when stepping on or stepping off the pedals. Always hold the stationary
handlebars first to get on the bike. During the workout always hold onto the stationary
handlebars.
7. Do not use the equipment outdoors.
8. Only one person should be on the equipment while in use.
9. Keep children and pets away from the product while in use. This machine is designed for adults
only. If you feel any chest pains, nausea, dizziness, or shortness of breath, you should stop
exercising immediately and consult your physician before continuing.
10. If you feel chest pains, nausea, dizziness, or shortness of breath, you should stop exercising
immediately and consult your physician before continuing.
11. The maximum weight capacity for this product is 400 lbs /180 kgs.
WARNING: Before beginning any exercise program consult your physician. This is
especially important for the persons who are over 35 years of age or who have
pre-existing health problems. Read all instructions before using any fitness equipment.
CAUTION: Read all instructions carefully before operating this product.
Retain this Owner’s Manual for future reference.
4
PRODUCT ASSEMBLY
THE FOLLOWING TOOLS ARE INCLUDED FOR ASSEMBLY:
Console
Pedal
Leveler
A
ccessory
Tray
Upright Post
Transportation
Wheel
Seat &
Back Pad
A
djustment
Handle
Quick
A
ccess
Key
Pulse Senso
r
T-HAND SOCKET
WRENCH (17mm)
SOCKET WRENCH
(13mm)
ALLEN WRENCH
(4 & 6 mm)
COMBINATION
WRENCH (65mm)
5
HARDWARE IDENTIFICATION CHART
This chart is provided to help identify the hardware used in the assembly process. Place the washers, the end of the bolts,
or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws.
NOTICE: The length of all bolts and screws except those with flat heads is
measured from below the head to the end of the bolt or screw. Flat head bolts and
screws are measured from the top of the head to the end of the bolt or screw.
After unpacking the unit, open the hardware bag and make sure that you have all the following items. Some hardware
may be already attached to the part.
Part No. and Description Qty
86 Lock Washer (M8) 6
87 Washer (8x38x2.0t) 4
96 Self-Tapping Screw, Truss Head (M4x10mm) 4
97 Self-Tapping Screw, Truss Head (M4x20mm) 4
99 Bolt, Round Head (M5xp0.8x15mm) 5
100 Bolt, Round Head (M5xp0.8x30mm) 2
107 Bolt, Socket Head (M8xp1.25x50mm) 2
112 Bolt, Hex Head(M8xp1.25x65mm) 4
117 Bolt, Hex Head (M10xp1.5x50mm) 2
6
ASSEMBLY PARTS
Unpack the box in a clear area. Follow the List of Assembly Parts below to check and make sure all assembly parts are
present and in good condition. Do not dispose of the packing material until the assembly process is completed. Assembly
tools and hardware kit have included for you to use when assembling the product
Console
Front & Back Console
Bracket
Front Decoration Cover Upper Handlebar
Upright Post Front & Rear Stabilizer Back Cushion Frame
Adjustment Handle &
Leveler
Accessory Tray Seat Handlebar Back Pad Seat Pad
Pedal Main Frame Back Cushion Cover
7
ASSEMBLY INSTRUCTIONS
Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing
materials from your area and place them back into the box. Do not dispose of the packing materials until
assembly is completed. Read each step carefully before beginning.
STEP 1Leveler Assembly
a. Before attach Levelers (28) to the
Stabilizer (2 & 3), first adjust
Leveler’s Nut to the middle of screw
line on Leveler (28) as the drawing 1
shown on the top right hand corner for
making sure that Leveler (28) is higher than the Transportation
Wheel (29). NOTE: The process is to prevent moving easily.
b. And then slightly attach 4pcs Levelers (28) to the Stabilizers (2, 3).
STEP 2 Stabilizer Assembly
a. In order to assemble the Stabilizer (2, 3)
smoothly, it is suggested to place one
Styrofoam (or any stationary object)
under one side of the Main Frame (1) that
is going to assemble the stabilizer.
b. Attach the Front Stabilizer (2) and the Rear Stabilizer (3) onto the
Main Frame (1) and fully secure with 4pcs Washers (8x38x2.0t)(87), 4pcs Lock Washers (M8)(86) and 4pcs Bolts,
Hex Head (M8xp1.25x65mm)(112). NOTE: If the item is not level, review the LEVELING NOTE on the right side to
level the Levelers (28).
Detailed Lever- drawing 1
Detailed Lever- drawing 2
Nut
Stabilizer
Leveler (28)
Transportation
Wheel
Stabilizer
Nut
Leveler (28)
LEVELING: After placing the bike
in the intended location for use,
check the stability of the bike. If the
bike is not level, reviewing the
following direction:
Loosen the Nut to make Leveler (28)
become less tight.
Rotate and adjust the Leveler (28)
for leveling. But always make sure
that Levelers has to be higher than
Transportation Wheels to prevent
moving easily.
Retighten the Nut securely against
the Stabilizer to lock the Leveler (28)
in stable position as the drawing 2
shown.
8
ASSEMBLY INSTRUCTIONS
STEP 3 Connection Wire Assembly
a. Plug the Middle Connection Wire (130) into the Lower Connection Wire (131). Be careful not to pinch the wires.
b. Plug the Pulse Sensor Wire 2 (134) into the Pulse Sensor Wire 3 (135). Be careful not to pinch the wires.
STEP 4 Upright Post Assembly
a. Refer to FIG. 1, check that 2pcs Thin Nylock Nuts (M10)(166) have pre-assembled into the front of the Main Frame
(1) (they will not be tight so that slotted bracket of the upright post will slide between the nut and
the frame).
b. Insert the Upright Post (8) into the Main Frame (1) and fully secure with 2pcs Bolts, Hex
Head (M10xp1.5x50mm)(117) by using the T-HEAD SOCKET WRENCH as shown. Then fully
tighten with 2pcs Thin Nylock Nuts (M10)(166).
STEP 5 Front Decoration Cover Assembly
Attach the Front Decorative Cover (13) onto the front of the Main Frame (1) with 2pcs Bolts, Round Head
(M5xp0.8x30mm)(100).
STEP 6 Upper Handlebar Assembly
NOTE: For shipping purpose, 4pcs Bolts, Hex Head Flange (M8xp1.25x20mm)(164)
already pre-attached to the Upright Post (8).
a. Remove 4pcs Bolts, Hex Head Flange (M8xp1.25x20mm)(164) from the Upright Post
(8).
b. Insert the Upper Handlebar (9) into the Upright Post (8) and fully secure with 4pcs
Bolts, Hex Head Flange (M8xp1.25x20mm)(164).
NOTE: Do not
remove the Nuts
(166) during
assembly
9
ASSEMBLY INSTRUCTIONS
S
TEP 7
Connection Wire
and Console
Assembly
NOTE: The console inside
has battery wire, be sure to
open the battery cover to
connect the battery wires
correctly, then assemble the
console cover back.
a. Plug the Console Wire
into the Middle
Connection Wire (130).
b. Plug the Console Wire
into the Pulse Sensor
Wire 2 (134). NOTE: Be
careful not to pinch the
wires; make sure each
console wire pin matches
correctly to each item
wire pin.
c. Place the Console (30)
onto the Upright Post (8) and fully secure with 4pcs Bolts, Round Head (M5xp0.8x15mm)(99).
STEP 8 Console Bracket Assembly
Attach the Front Console Bracket (152) and the Back Console Bracket (153) to the Upright Post Assembly (8) and
fully secure with 4pcs Self-Tapping Screws, Truss Head (M4x20mm)(97) and 1pcs Bolt, Round Head
(M5xp0.8x15mm)(99).
S
TEP 9 Pad Adjustment Lever Assembly
a. Refer to FIG. 2, 1pcs Bolt, Socket Head (M5×p0.8×15mm)(161) and 1pcs
Lock Washer (M5)(155) already pre-attached to the second screw hole of the
Pad Adjustment Lever (75).
b. Remove 1pcs Bolt, Socket Head (M5×p0.8×15mm)(161) and 1pcs Lock
Washer (M5)(155) from the second screw hole of the Pad Adjustment Lever
(75).
c. Follow FIG.2’s arrow to gently move the Pad Adjustment Lever (75) outward
until it aligns with the first screw hole as the drawing shown on the right, then fully
tighten with 1pcs Bolt, Socket Head (M5×p0.8×15mm)(161) and 1pcs Lock
Washer (M5)(155).
d. Continue fully tighten 1pcs Bolts, Socket Head (M5×p0.8×15mm)(161) and
1pcs Lock Washer (M5)(155) that already pre-attached on the first screw hole
of the Pad Adjustment Lever(75).
S
TEP 10 Adjustment Lever Assembly
NOTE: For shipping purpose, each Adjustment Lever
has pre-assembled one pcs Nut (M8)(122) as the
illustration shown on the left.
a. Attach each one Adjusting Handle (39) to two Adjustment Levers to the proper desired
position.
b. To fully secure the Adjusting Handle (39) by rotating the Nut (M8)(122) in
counter-clockwise direction until completely reach to the Adjusting Handle (39).
Fully Tighten
10
ASSEMBLY INSTRUCTIONS
STEP 11 Back Pad Frame Assembly
NOTE: For shipping purpose, 4 pcs Lock Washers (M8)(86) and 4 pcs Bolts,
Button Head (M8xp1.25x16mm)(160) already pre-attached on the Back Pad
Adjustment Bracket (5).
a. Remove 4 pcs Lock Washers (M8)(86) and 4 pcs Bolts, Button Head
(M8xp1.25x20mm)(160) at both sides of the Back Pad Adjustment
Bracket (5).
b. Follow the direction of the drawing line. Insert the Back Pad Frame (6)
onto the Back Pad Adjustment Bracket (5) and fully secure with 4 pcs
Lock Washers (M8)(86) and 4 pcs Bolts, Button Head
(M8xp1.25x20mm)(160).
S
TEP 12 Back Pad & Cover Assembly
NOTE: For shipping purpose, 4 pcs Bolts, Button Head (M8xp1.25x20mm)(104) and 4pcs Bolts,
Round Head (M6xp1.0x15mm)(102) has pre-attached on the back of the Back Pad (48).
a. Remove 4 pcs Bolts (M8xp1.25x20mm)(104) and 4pcs Bolts (M6xp1.0x15mm)(102) from
the back of the Back Pad (48).
b. Attach the Back Pad (48) onto the Back Pad Frame (6) and fully secure with 4 pcs Bolts,
Button Head (M8xp1.25x20mm)(104).
c. Then attach the Back Pad Cover (49) onto the Back Pad (48) and fully secure with 4pcs
Bolts, Round Head (M6×p1.0×15mm) (102).
STEP 13 Accessory Tray Assembly
Refer to FIG.3. Turn the Seat Handlebar (4) to have the Hand Pulse Sensor Plate downward. Attach the Accessory
Tray (40 & 145) onto the Seat Handlebar (4) and fully secure with 4pcs Self-Tapping Screw, Truss Head
(M4x10mm)(96). NOTE: Do not damage the Pulse Sensor Wire 4 (136) during Step 13.
STEP 14 Pulse Sensor Wire Assembly
Connect the Pulse Sensor Wire 4 (136) to the Pulse Sensor Wire 3 (135).
STEP 15 Seat Handlebar Assembly
Follow the direction of the drawing line. Place the Seat Handlebar (4) onto the Main Frame (1) and fully secure with 2pcs
Lock Washers (M8)(86) and 2pcs Bolts, Socket Head (M8xp1.25x50mm)(107).
11
ASSEMBLY INSTRUCTIONS
STEP 16 Seat Pad Assembly
NOTE: For shipping purpose, 4 pcs Bolts, Hex Head (M8xp1.25x20mm)(141) already
pre-attached at the bottom of the Seat Pad (46).
a. Remove 4pcs Bolts, Hex Head (M8xp1.25x20mm)(141) from the bottom of the Seat Pad
(46).
b. Attach the Seat Pad (46) onto the Seat Frame (7) and secure with 4pcs Bolts, Hex Head
(M8xp1.25x20mm)(104).
STEP 17 Pedal Assembly
NOTE: The Right Pedal has an R stamped on the end of
pedal shaft. The Left Pedal has L stamped on the end of the
pedal shaft.
a. Tread the Right Pedal (16) clockwise into the Right
Crank located inside the Right Crank Cover. Tighten
the pedal securely.
b. Thread and tighten the Left Pedal (15)
counter-clockwise into the Left Crank.
***For the final step, make sure all the bolts and nuts are tightened securely before using the item***
12
OPERATIONAL INSTRUCTIONS
H
OW TO TRANSPORT THE BIKE SAFELY
Hold the Rear Stabilizer (3) up with two hands and tow the item to
the desired place carefully
Make sure the floor is level while towing the item
B
ACK PAD ADJUSTMENT
To adjust the most suitable angle, pull the Back Cushion
Adjustment Handle upward while lying on the cushion.
Release the Back Cushion Adjustment Handle and hear the
“click” sound to secure the desired angle of the back cushion.
SEAT PAD ADJUSTMENT
To adjust the seat distance from the pedals, it’s suggested to
place your feet on each pedal.
Hold the upper handlebar with your left hand and use your
right hand to pull the Seat Adjustment Handle upward while
using your feet to slide the seat distance forward and
backward until the seat reaches to the proper position.
Release the Seat Adjustment Handle. You will hear a “click”
sound to lock the seat.
13
CONSOLE OPERATION INSTRUCTIONS
Please read the console operation instruction thoroughly and get familiar with the console layout. Practice using
this console before you start in order to get a better understanding of the functions. Below is the console layout
and detailed operation instructions.
Layout:
-- The USB port is for software updates only, please do not use for charging or other software usages. --
Keys
This is an interactive screen, therefore there are keys on the screen as well as fixed keys which is listed below.
Note: When the button is grey out on the screen, it means the function is not available at this time.
Go key: Pressing this key during home screen before you select a program will activate the Quick Start
program immediately with default user values. Or pressing this key during the program setup after a
program is selected will start the selected program.
/keys: Used for user data adjusting during program setup and resistance level/ heart rate adjustment
while a program is running.
Home key: Used to exit the current activities and go back home/idle mode.
Keys
D
14
Displays
Since this is an interactive display, therefore the screen will change according to with your finger tip’s touch.
Follow the screen instruction to operate this console. Here are a few common screens you will see and their
operations –
Home screen: there are 4 functions in the home screen: User, Program, Just Go & Settings. Press each
tab will prompt the appropriate function and its related screen for the next action.
o User button: touch this button to get into user setting. There are 4 different user profiles to select
from. If there is a user stored in one of the profile already, his/her name will be displayed. The
user profile is password protected function. The initial password is “0000”. Once you get into a
user profile, you will be able to change your password, input your name as well as your personal
program settings. Make sure you press “SAVE” button to save your user information.
When a user is selected, you can then jump to a workout program without entering your program
setting again or you can enter user profile to change or review user information/workout history.
When you finish a workout via user function, the workout total will be stored into your user profile
automatically. You will be able to review them later in in your user profile.
o Program button: touch this button is to enter program selection screen. Touch your desired
program button and follow on screen instruction to set up program settings and start the program.
Or you may press “GO” button to bypass setting and use defaults to start the program right
away.
15
o Just Go button: touch this button to jump start Quick Start program. The time will count up. You
may adjust resistance level at any time or touch Cool Down button to end program and enter
cool down.
o Settings button: touch this button to see product record as well as changing the units system
from English to Metric. There are also engineering functions inside which is for technician
maintenance only, such as “calibration and software update”. This information is password
protected and the preset password is “2015”.
16
Basic Operation
Power up: Since this is a self-generating product, user must pedal the product to power up the console.
Pause a program: If a program is running and there is no RPM for a few seconds, the console will pause
and stop accumulating data. The pause time is 3 minutes. After that, the console will reset back to home
screen/idle mode. Within pause mode, pedal again to resume the program.
Power save function: This console is equipped with power save function. If there is no RPM, the console
screen will be off and enter power save mode.
Start a program: There are three ways to start a workout from home screen –
o Touch the “Just Go” button on screen or “Go” key to start Quick Start program.
o Or touch “User”, then “Program” button to start a preset program using user profile. This is the
only way to get into your favorite programs. The program will start immediately using pre-stored
user profile. This is the recommended method to start a program.
o Lastly, touch “Program” button to select a program. The console will treat this as a guest user
which means the user setting will be prompted before the program starts. Follow on screen
instruction to set up the personal data. When finished entering data, press the “Go” key to begin
the workout. (You may press “Go” key anytime during setup to bypass and start the workout
immediately.) Note, since this is a guest user workout, there is no user profile setup, therefore
the workout summary will not be stored into the user profile.
Default values: Initially the console is coded with a set of defaults for express quick start. If you didn’t
adjust these values before the program started, they will be used for data calculations, such as calories.
It is recommended you set up a user profile and adjust these values with your own personal data to get
the most accurate workout feedbacks. The factory defaults are:
o Age – 35
o Weight – 150lbs or 70kg
o Program time – 30 minutes (min program time allowed is 5 minute & max program time allowed
is 90 minutes)
o Target HR & Work HR – 70% max HR (Max HR is calculated as 220-age)
o Resistance level: 30 levels available
End a program and review summary: When program time is reached or “Cool Down” button is pressed, it
will end the program and enter Cool Down & Summary Review mode. There are 3 minutes for cool
down & review the workout summary. During Cool Down, you may adjust resistance level up to level 10.
If “Save as Favorite” button appears on screen, you may press this button to save the current workout
program as a favorite program of yours. Follow on screen instruction for operation.
17
Workout Programs
Besides Quick Start function, there are 9 program options as well as favorite programs for your selection:
Manual, Random, Interval, Hill Climb, Strength, Target HR, HR Interval, Fat Burn, Cardio and Favorites.
Quick Start: Pressing “GO” key or “Just Go” on screen during home screen/idle mode will quick start the
console. The program will use factory defaults for calculation and display. The time will count up and each
segment of progress profile equals 1 minute. You may stop pedaling at any time or press “Home” key to end the
program.
Classic programs: This group includes Manual, Random, Intervals, Hill Climb & Strength program.
These programs are preset profile programs and behave similar. Select a user, then touch the desired program
to start the program right away. Or touch Program button and follow the instruction to set up the guest data and
start the program. You may adjust the resistance level by pressing “/” key during program. The program
profile will update accordingly.
Manual program: The default resistance level for Manual program is L1.
Random program: This is a computer generated profile program and it is different each time.
Intervals, Hill Climb & Strength program are preset profile programs.
18
HR programs: The Heart Rate programs are designed to keep you training at the chosen heart rate
level. These programs will only work when there is a valid heart rate signal. For the safety, the
program is to start with a warm up session to get the heart rate up close to 20% of the target before it
begins the heart rate training session.
During warm up, user may press “/” key to adjust the resistance and get the heart rate up. As
soon as the heart rate training session begins, the console will take control and adjust the resistance
level automatically to ensure your target heart rate is achieved and maintained during the entire
program.
Target HR program: Target HR is retrieved from the user profile if a user is selected or default heart rate
target (set as 70% max HR). You may also press “/” key to adjust the target heart rate setting during
heart rate control session of the exercise.
HR Interval program: There are two phases of this training: Work Interval and Rest Interval. After warm up,
the console will take the target HR setting to begin Work interval and adjust the resistance automatically.
When the target setting is reached and lasted for 30 seconds, it will then enter Rest interval and reduce
the resistance down to level 2 for 2 segments of time for resting. It will repeat this process throughout
the entire program.
Fat Burn & Cardio program: the target HR for Fat Burn program is set at 70% of max HR for efficiently
body fat burning purpose. Target HR for Cardio program is set at 80% of max HR for strengthening
heart condition. These HR targets cannot be adjusted during program. The target bpm is calculated with
entered user age. So it is recommended the age is entered correctly during program setting.
Note: During exercise, the profile on the screen will just show a simulated heart rate graph; there is no relation
to the actual heart rate. The pulse data display window will show the actual heart rate.
Example: Target HR program exercising screen
Simulated graph;
no relation to the
actual heart rate.
19
Favorite programs: These program are the spaces for you to store your own workout profile for
future use. There are 4 favorite program spaces per user.
Since each favorite program belongs to a user, to save a favorite program, first you must select a user,
then select a “Classic” program to start the workout & build the program profile. During Cool down
mode, you may press “Save as Favorite” button to save this profile. Follow the prompts to save the
program into favorites. The program name as well as program profile will be stored into the favorite
program you selected. You may overwrite an existing favorite program by selected the grey out
favorite program number and select “Yes” to overwrite.
To recall a favorite program, first select a user, then program button, the favorite programs will appear
for selection. Once a favorite program is selected, it will start the program right away. Favorite program
operation behaves the same as the original Classic program.
Heart Rate Monitoring Devices & Exercise Tips
Pulse Hand Grips
This product comes standard with stainless steel pulse handgrips. To activate, gently grasp both
handgrips to obtain a heart rate reading. (Note: It is recommended to wear a chest strap for Heart Rate
control program, as it is more accurate. If you wear a chest strap and use hand grips at the same time
for heart rate monitoring purpose, please note the console will take the measurement of the chest
strap.)
Pulse Grip Operating Tips: If you are not getting a consistent reading while using the hand pulse
option, we recommend the following suggestions:
Make sure that the palms of the hands are touching the contact area of each hand pulse grip.
Maintain an even pressure on the grips.
Do not hold the hand pulse grips too tightly.
Built in Wireless Heart Rate Receiver
Note: Chest strap transmitter does not come with this unit; contact BODYCRAFT, or your dealer for
purchase.
This product is equipped with a built-in receiver for your heart rate monitoring. Any heart rate telemetry
strap that transmits at 5Khz is compatible. To get an accurate reading using these devices, you will
need to be within three feet of the console, and a minimum of four feet from others using a heart rate
monitoring device.
(Note: The transmitter may fluctuate erratically if you are too close to other heart rate monitoring
equipment or there is other electronics near by, such as TV, Radio...)
While using heart rate control modes, the computer monitors the exact measurement of your pulse.
Heart rate frequency is displayed while the computer continually compares heart rate to the
preprogrammed personal data. The computer adjusts the wattage to maintain heart rate at the
preprogrammed level.
How to Wear Your Sensor/ Transmitter (Chest Strap)
1. Buckle one end of the chest strap onto the transmitter.
2. Adjust the band length so that the fit is snug, but not too tight.
3. Buckle the other end of the chest strap onto the transmitter.
4. Center the transmitter on your chest below the pectoral muscle (breasts).
5. Stretch the transmitter away from your chest and moisten the conductive electrode strips
located next to the buckles with water.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27

BodyCraft R1000G Owner's manual

Category
Fitness, gymnastics & weight training
Type
Owner's manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI