Shimano SC-MT800 User manual

Brand: Shimano

Model: SC-MT800

Type: User manual

This manual is also suitable for

SC-M9051

One Holland, Irvine, California 92618, U.S.A. Phone: +1-949-951-5003

High Tech Campus 92, 5656 AG Eindhoven, The Netherlands Phone: +31-402-612222

3-77 Oimatsu-cho, Sakai-ku, Sakai City, Osaka 590-8577, Japan

Please note: speciﬁ cations are subject to change for improvement without notice. (English)

UM-7GC0B-006-00

User's manual

System Information Display

User's manuals in other languages are available at :

http://si.shimano.com

IMPORTANT NOTICE

• Contact the place of purchase or a bicycle dealer for information on installation and adjustment

of the products which are not found in the user's manual. A dealer's manual for professional

and experienced bicycle mechanics is available on our website (http://si.shimano.com).

• Do not disassemble or alter this product.

• The Bluetooth

word mark and logos are registered trademarks owned by the Bluetooth SIG,

Inc. and any use of such marks by SHIMANO INC. is under license.

Other trademarks and trade names are those of their respective owners.

For safety, be sure to read this user's manual thoroughly

before use, and follow them for correct use.

Important Safety Information

For replacement information, contact the place of purchase or a bicycle dealer.

WARNING

• When the shifting switch is operated, the motor which drives the front derailleur will operate

to the shifting position without stopping, so be careful not to get your ﬁ ngers caught.

• After reading the user's manual carefully, keep it in a safe place for later reference.

Note

• When using a system information display, combine it with one of the following units.

External type: BM-DN100, Built-in type: BT-DN110

• Be sure to attach dummy plugs to any unused terminals. If water gets into any of the

components, operating problems or rusting may result.

• This is a small waterproof connector. Do not repeat connecting and disconnecting it. It may

impair the function.

• Be careful not to let water get into the terminal.

• The components are designed to be fully waterproofed to withstand wet weather riding

conditions; however, do not deliberately place them into water.

• Do not clean the bicycle in a high-pressure car wash. If water gets into any of the components,

operating problems or rusting may result.

• Handle the products carefully, and avoid subjecting them to any strong shocks.

• Do not use thinners or similar substances to clean the products. Such substances may damage

the surfaces.

• Contact the place of purchase for updates of the product software. The most up-to-date

information is available on the Shimano website.

• Disconnect Bluetooth LE when not using E-TUBE PROJECT for smartphones/tablets.

Using the system information display without disconnecting Bluetooth LE may result in high

battery power consumption.

• Products are not guaranteed against natural wear and deterioration from normal use and

aging.

• For maximum performance we highly recommend Shimano lubricants and maintenance

products.

Regular inspections before riding the bicycle

Before riding the bicycle, check the following items. If any problems are found with the

following items, contact the place of purchase or a bicycle dealer.

• Is the system information display securely installed to the handlebar?

• Is there sufﬁ cient charge remaining in the battery?

• Is there any noticeable damage to the electric wires?

• Is the dummy plug attached to the terminal?

Names of parts

Some items may not be displayable or selectable depending on the connected components and

software version. Consult a dealer regarding the usable items for the product you are using.

Mode

switch

Terminal

Charging

port

Display

A B C D

A Battery level D Suspension setting

B Front derailleur Gear position E Operation mode

Rear derailleur Gear position/RD Protection Reset mode

A. Battery level

Display Battery level Display Battery level

81% - 100% 26% - 40%

61% - 80% 1% - 25%

*1*2*3

41% - 60% 0%

* 1 When the battery level becomes low, the operation of the suspensions is restricted to the

unlocking direction. The operation of the rear suspension is restricted ﬁ rst, then the front

suspension's is also restricted.

* 2 When the battery level drops below 5%, the operation of the front derailleur is restricted.

* 3 When the battery level decreases further, both the suspensions and derailleurs cease

operating, with the derailleurs ﬁ xed at the last shifted position. The battery indicator blinks

for 2 seconds at the time of input operation. We recommend early charging of the battery.

B. Front derailleur Gear position

The gear position of the front derailleur is displayed.

Display Gear position

Largest chainring

Middle chainring

Smallest chainring

* In the case of double speciﬁ cation, only the largest chainring and smallest chainring are

displayed.

C. Rear derailleur Gear position/RD Protection Reset mode

Display Details

Number The gear position of the rear derailleur is displayed.

RD Protection Reset will operate.

D. Suspension setting

Three types of front and rear suspension combinations can be conﬁ gured.

Display Details

If the suspension settings are already conﬁ gured, one of the settings can be

selected from the screen indications.

*1*2

If the suspension settings are not conﬁ gured, the suspensions are not

connected, or the battery level is running low, the display will be blank.

* 1 Suspension settings are conﬁ gured in E-TUBE PROJECT. For details, consult a dealer or an

agency.

* 2

Depending on the type of suspension, settings may be factory conﬁ gured at the time of

shipment. Check the indications displayed on the system information display screen, and if the

arrows are displayed, be sure to check the setting details.

E. Operation mode

The operation mode is displayed.

Display Mode Details

Front derailleur/

Rear derailleur adjustment

Adjustment setting is done in this mode. For

the setting procedure, contact a dealer or an

agency.

Manual shift Gears are shifted manually in this mode.

Shift mode 1

The shift mode set in E-TUBE PROJECT can

be used.

Shift mode 2

Speciﬁ cations

SC-MT800 SC-M9051

Frequency band 2,402 – 2,480 MHz

Maximum radio-frequency power +4 dBm

Firmware version 4.0.9 – 4.1.1 –

Functions

Cycle computer connection

The system information display transmits the following four types of information to cycle

computers or receivers that are compatible with ANT

+TM

or Bluetooth

LE connections.

1) Number of gears (front, rear)

2) DI2 battery level

3) Adjustment mode information

4) D-FLY channel switch information

For information on which of the above types of information is to be displayed, refer to the

manual for your cycle computer or receiver.

* The latest functions can be checked by updating the software via E-TUBE PROJECT. For details,

consult the place of purchase.

E-TUBE PROJECT connection

E-TUBE PROJECT for smartphones/tablets may be used if a Bluetooth LE connection is established

with a smartphone/tablet.

How to make connections

Cycle computer connection

To make a connection, the cycle computer needs to be in connection mode. For information on

how to put the cycle computer into connection mode, refer to the manual for the cycle

computer.

1) Put the cycle computer into connection mode.

2) Perform gear shifting operations.

If you cannot connect after performing gear shifting operations, perform the following

operations.

■When using an external battery

Check that the electric wires are connected to the system information display. Then, remove

and remount the external battery.

■When using a built-in battery

Check that the electric wires are connected to the system information display. Then, remove

the electric wires from the system information display and reconnect them.

(Connection transmission begins about 30 seconds after the battery is remounted or the

electric wires are reconnected to the system information display.)

3) This completes the connection process.

Check on the cycle computer to see if connection was successful.

If a connection cannot be made in the way described above, refer to the manual for your cycle

computer.

For information on how to show the number of gears or the DI2 battery level, refer to the

manual for the cycle computer.

E-TUBE PROJECT connection

Before setting up a connection, turn on Bluetooth LE on the smartphone/tablet.

1) Open E-TUBE PROJECT and set it to listen for Bluetooth LE signals.

2) Press the mode switch until "C" appears on the display. The cycle computer will

begin signal transmission. The unit name displays in E-TUBE PROJECT.

* Release the mode switch or button as soon as the unit on the bicycle begins

signal transmission.

If the mode switch or button is held down for any longer, a different mode will

be activated.

3) Select the unit name displayed on screen.

* To disconnect, cancel the Bluetooth LE connection from the smartphone/tablet. (The cycle

computer will exit connection mode and return to regular operation mode.)

How to operate

 Switching operating modes

Operation mode Sub-operation mode

Shift mode

Double click

Press and hold

0.5 seconds

or more

Bluetooth LE

connection mode

2 seconds

or more

Adjustment mode

Double click

5 seconds

or more

RD Protection Reset mode

Mode switch

To end Adjustment mode or RD Protection Reset mode, press for 0.5 seconds or more.

For the setting procedure, contact a dealer or an agency.

 About the RD Protection function

Rotate the front chainwheel while restoring operation after the RD Protection function has

activated.

In order to protect the system from falls etc., the RD Protection function will operate when the

rear derailleur is subjected to a strong impact. The connection between the motor and the link is

momentarily severed so that the rear derailleur will no longer operate. If this happens, press the

mode switch for 5 seconds or more. This will restore the connection between the motor and the

link, and clear the RD Protection function for the rear derailleur. If recovery cannot be

performed through switch operation, manual operation is also possible. Consult with a

distributor in advance.

5 seconds or

RD Protection Reset

 System information display

Front gear position changes according to rear gear position. These settings can be changed in

E-TUBE PROJECT. For details, consult a dealer or an agency.

 About the beep

Beeps are set to sound in the following situations during gear operation.

Beep sounds Situation

One short

beep

Indicates that the gear shifting limit has been reached. (When the chain is

on the highest gear for both front and rear or lowest gear for both front

and rear)

Two short

beeps

Indicates that the front gears are being shifted in shift mode. These beeps

sound the next time the front gears are shifted.

One long

beep

Indicates that the front derailleur cannot be shifted when the battery is

running low. Blinking continues for 2 seconds after the sound has stopped.

(Only one beep sounds when the gears are shifted)

Indicates that there is an error with the suspension.

All suspension mode arrows blink and continue to blink for 2 seconds after

the sound has stopped.

Shimano SC-MT800 User manual

Brand: Shimano

Model: SC-MT800

Type: User manual

This manual is also suitable for

SC-M9051

Download PDF

report

Shimano SC-MT800 User manual

This manual is also suitable for

Shimano SC-MT800 User manual

Related papers