Page is loading ...
Page is loading ...
Page is loading ...
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, ammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed
if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• Consult a technician if you are not sure how to use or connect the product.
• Maintenance, modications and repairs must be done by a technician or a
specialist repair centre.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Electrical safety
• The mains outlet must be located near to the device and be easily accessible.
• Only use the supplied mains adapter as a power source.
• Only connect the power adapter to a standard mains socket connected to the
public grid. Before plugging in the power adapter, check whether the voltage
stated on the power adapter complies with the voltage of your electricity supplier.
• Never connect or disconnect power adapters if your hands are wet.
• Never unplug the power adapter from the mains socket by pulling on the cable;
always use the grips on the plug.
• When setting up the product, make sure that the cable is not pinched, kinked or
damaged by sharp edges.
• Always lay the cables so that nobody can trip over or become entangled in them.
This poses a risk of injury.
• For safety reasons, disconnect the power adapter from the mains socket during
storms.
• The power adapter is constructed with protection class II.
• Do not touch the power adapter if there are any signs of damage, as this may
cause a fatal electric shock! Switch off the mains voltage to the mains socket to
which the power adapter is connected (switch off at the corresponding circuit
breaker or remove the safety fuse, then switch off at the corresponding RCD
protective switch, so that all poles of the mains socket are disconnected). Then
unplug the power adapter from the mains socket. Dispose of the faulty power
adapter in an environmentally friendly way and discontinue use. Replace it with a
power adapter of the same design.
• Never pour any liquids over electrical devices or put objects lled with liquid next
to the device. If liquid or an object does enter the interior of the device, power
down the respective socket (e.g. switch off the circuit breaker), and then unplug
the mains plug from the mains socket. Discontinue use and take the product to
a specialist repair centre.
• Never use the product immediately after it has been brought from a cold room
into a warm one. The condensation generated could destroy the product. In
addition, the power adapter may cause a fatal electric shock! Allow the product to
reach room temperature before connecting it to the power supply and putting it to
use. This may take several hours.
c) Persons and product
• Do not cover any of the ventilation grilles, otherwise the device may not cool
properly.
• Ensure that there is sufcient ventilation. Do not cover the device housing!
Operating instructions
Wireless HDMI stick with receiver
Item no. 1499829
Intended use
This wireless set is designed to transfer an HDMI signal from a video output device (e.g. PC,
DVD player or Blu-Ray player) to a display device (e.g. TV or monitor). The receiver is powered
by a power adapter, which is included with the product. The transmitter is powered via a USB-Y
cable connected to two USB ports (see "Technical data").
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
Do not attempt to rebuild and/or modify this product. If you use the product for purposes other
than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuits, re and electric shocks.. Read the instructions carefully
and keep them. Make this product available to third parties only together with its operating
instructions.
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
HDMI is a registered trademark of HDMI Licensing L.L.C.
Restrictions
The following countries impose restrictions on the use of the product:
DE AT NL SE PL SK SI LT EE LV
FI FR UK BE CZ HU IT ES PT EL
DK BG CY HR IE IS LU MT RO
The product must only be operated indoors.
Delivery content
• Transmitter stick
• Receiver box
• HDMI cable (15 cm long)
• USB-Y power cable (60 cm long)
• Power adapter
• Operating instructions
Up-to-date Operating Instructions
Download the latest operating instructions at www.conrad.com/downloads, or scan the QR
code above. Follow the instructions on the website.
Explanation of symbols
The symbol with the lightning in the triangle is used if there is a risk to your health,
e.g. due to an electric shock.
This symbol indicates particular hazards associated with handling or operation.
The “arrow” symbol indicates special tips and operating information.
The product must only be used in dry, enclosed indoor areas. This product must not
become damp or wet, as this may result in a fatal electric shock!
This symbol indicates that this product is built according to protection class II. The
product is equipped with reinforced or dual insulation between the mains circuit and
the output voltage.
Operating elements
a) Receiver box
4
3
1
2
1 Pairing button
2 PAIRING LED
3 HDMI OUT (output)
4 Micro USB port
The transmitter does not support infrared, therefore it cannot be used with the IR IN
socket.
b) Transmitter stick
ABCD
USB
A HDMI port
B Pairing button
C Micro USB port
D LED indicator
Setup and connection
• Place the receiver on a level surface near the video output device. If necessary, use a cloth
to protect the surface of your furniture.
• Switch off all devices that you want to connect to the wireless set.
• Connect the transmitter stick to an HDMI port on your video output device (e.g. the HDMI port
on a computer or a DVD/Blu-Ray player). The transmitter is powered via the USB-Y cable.
Insert each USB-A connector on the USB-Y cable into a USB port on a computer, and then
connect the micro USB connector to the micro USB port (C).
Each USB port must provide a current of 500 mA. If necessary, connect the USB-Y
cable to the USB ports on the back of your computer. The transmitter stick must be
connected to two USB ports to ensure that there is sufcient power. If you wish to
use a USB hub to power the transmitter stick, ensure that the hub is connected to an
external power supply, otherwise the USB ports may not provide a sufcient current
(see "Technical data").
• Insert the HDMI cable into the HDMI OUT socket (3), and then connect the other end of the
cable to an HDMI port on your display device (e.g. monitor, TV or projector).
• Insert the USB connector on the power adapter into the micro USB port (4) on the receiver.
Connect the power adapter to a suitable mains socket.
Connection diagram
USB-Y power cable Power adapter
HDMI port
HDMI cable
HD projector
Laptop
• Connect the HDMI port (A) to the output socket on your video output device, such as a
computer, Blu-Ray player, or games console (e.g. PS4 or Xbox). If necessary, use the 15 cm
HDMI cable supplied.
• The distance between the transmitter and receiver should not exceed 30 m.
• Insert the micro USB connector into the micro USB port (C) on the transmitter stick.
• Connect the video output device and the display device to a power source and turn them on.
Setup and operation
• The red LED indicator (D) on the transmitter will turn on when the transmitter is connected
to a USB power source.
• The PAIRING LED (2) on the receiver indicates that the receiver is connected to the mains.
a) Pairing the transmitter with the receiver
• Press the pairing button (1) on the receiver.
• A message will be displayed on your display device.
• Press the pairing button (B) on the transmitter.
• A wireless connection will be established automatically.
b) LED indicator status
Status Transmitter (TX) Receiver (RX)
Connected to a power
supply
Red Red
PAIRING button (1 and B)
pressed
Flashing red Blue
Not paired Flashing blue Blue
Paired Blue Blue
Follow the onscreen prompts on your display device during the pairing process.
c) Wireless range
The maximum transmission range is 30 m. The range may be reduced by the following:
• Walls and reinforced concrete ceilings
• Double glazed windows
• Proximity to metal and conducting objects (e.g. radiators)
• Proximity to people
• Devices working on the same frequency (e.g. wireless video systems and Wi-Fi devices)
• Proximity to electrical devices, motors, transformers, power adapters,
• and computers
• Proximity to computers or other electrical devices with exposed components.
The range can vary signicantly depending on the surroundings. If reception is poor, try moving
the receiver to another location. Do not place the receiver behind a TV.
Troubleshooting
Problem Possible cause Suggested solution
There is no image
on the display
device.
The cables are not
connected correctly.
Check that all cables are connected
correctly.
For best results, use a high-speed
HDMI cable.
Disconnect the transmitter and
receiver from the power supply to
restart the system.
There is no sound. HDCP compatibility
issues.
Adjust the volume on your display
device.
Check that all cables are intact and
connected correctly.
Disconnect the transmitter and
receiver from the power supply to
restart the system.
There is no 3D
effect on the display
device.
3D mode is disabled.
Incompatible 3D shutter
glasses
Enable 3D mode on your monitor,
DLP projector and signal source
(AUTO or 3D ON).
Check that the shutter glasses have
sufcient battery power remaining.
Ensure that you are using the correct
shutter glasses for your 3D system.
The image quality
is poor.
Other wireless
devices (e.g. routers
or microwaves)
are interfering with
transmission.
Remove any sources of interference.
Place the receiver and transmitter in
an area without interference.
The transmitter
and receiver do
not connect, or
the connection
terminates.
The video output device is
not switched on.
System error
Connect the video output device to
the mains and switch it on.
Disconnect the transmitter and
receiver from the power supply to
restart the system.
Pair the transmitter and receiver
again (see "Pairing the transmitter
with the receiver").
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2018 by Conrad Electronic SE. *1499829_v6_0620_02_jc_m_4L
Maintenance and cleaning
• Under no circumstances should you service any of the components in the interior of the
product, therefore never open/dismantle it.
• This device does not require maintenance except for occasional cleaning.
• Disconnect the product from the power supply and any connected devices before cleaning it.
• Do not immerse the product in water.
• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these could
damage the casing or even impair the functioning of the product.
• Use a dry, soft, and lint-free cloth to clean the product. Do not press too hard on the surface
when cleaning, as this may lead to scratch marks.
Declaration of Conformity (DOC)
Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau hereby declares that this
product conforms to the 2014/53/EU directive.
Click on the following link to read the full text of the EU declaration of conformity:
www.conrad.com/downloads
Select a language by clicking on a ag symbol and enter the product order number
in the search box. You can then download the EU declaration of conformity in PDF
format.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product according to
the relevant statutory regulations.
You thus full your statutory obligations and contribute to the protection of the environment.
Technical data
a) Receiver and transmitter
Transmission frequency................................... 5180 – 5240 MHz (5 GHz band)
Transmission bandwidth ................................. 20 MHz or 40 MHz
Transmission range ......................................... max. 30 m (with no obstacles)
Supported video resolutions ............................ 480 to 1080 i/p 60 Hz
Transmission rate ............................................ Up to 3 Gbit/s (video)
Up to 180 Mb/s (audio)
Delay ............................................................... <0.5 seconds
Copy protection ............................................... HDCP 2.0
Encryption ........................................................ 128/256-bit AES
Operating conditions ....................................... 0 to +45 °C, 0–80 % RH (non-condensing)
Storage conditions .......................................... -10 to +60 °C, 0–80 % RH (non-condensing)
b) Receiver
Input voltage/current ........................................ 5 V/DC, max. 1 A (via power adapter)
Output .............................................................. 1 x HDMI
Dimensions (W x H x D) ................................. 85 x 14 x 83 mm
Weight ............................................................. Approx. 72 g
c) Power adapter
Input voltage/current ........................................ 100 - 240 V/AC, 50/60 Hz, 0.2 A
Output voltage/current ..................................... 5 V/DC, 1 A
Cable length .................................................... 150 cm
d) Transmitter
Input voltage/current ........................................ 5 V/DC, 1 A (via USB)
Input (transmitter) ............................................ 1 x HDMI
Power supply ................................................... USB-Y power cable
Cable length (USB-Y cable) ............................ 60 cm
Cable length (HDMI cable) .............................. 15 cm
Transmission power......................................... max. 9.86 dBm
Dimensions (W x H x D) .................................. 39 x 16 x 86 mm
Weight ............................................................. Approx. 85 g
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- français: Renkforce RF-HDFS-01 Le manuel du propriétaire
- Deutsch: Renkforce RF-HDFS-01 Bedienungsanleitung
- Nederlands: Renkforce RF-HDFS-01 de handleiding
Related papers
-
Renkforce RF-UH-A4 Owner's manual
-
Renkforce 7 ports USB 3.0 hub wall mount option, Steel casing Owner's manual
-
-
-
-
-
-
-
-
Other documents
-
Sabrent HDMI-EXTC User guide
-
VOLTCRAFT 1594595 Operating instructions
-
-
-
-
VOLTCRAFT SPAS-2100 Operating instructions
-
-
Sygonix 2757593 User manual
-
Linie 70984 Installation guide
-
