LG 22LF15R User manual

LCD TV

OWNER’S MANUAL

LCD TV MODELS

22LF15R

26LF15R

32LF15R

Please read this manual carefully before operating your

TV.

Retain it for future reference.

Record model number and serial number of the TV.

Refer to the label on the back cover and quote this

information.

To your dealer when requiring any service.

ENGLISH

1

Ensure that the following accessories are included with your TV. If an accessory is missing, please contact the

dealer where you purchased the product.

■

Image shown may differ from your TV.

Owner's

Manual

Owner’s manual

Owner’s Manual Batteries

Power Cord

Polishing Cloth

Polishing cloth for use

on the screen

This feature is not

available

for all models.

*Lightly wipe any stains or

fingerprints on the surface

of the TV with the polishing

cloth.

Do not use excessive force.

This may cause scratching or

discolouration.

Bolts for stand assembly

(Refer to p.7)

(Except for 22LF15R)

x 4 x 4

Screw for stand fixing

(Refer to p. 8)

(Except for 22LF15R)

ACCESSORIES

RA

TIO

Remote Control

Cable Management Clip

(Refer to p. 10)

(Only 22LF15R)

Protection Cover

(Refer to p. 13)

or

Wall Mounting Bracket(Separate purchase)

AW-47LG30M

(Only 32LF15R)

(Only 22LF15R)

RW120

(Only 26LF15R)

RW230

ACCESSORIES

Picture Size (Aspect Ratio)Control .........................41

Preset Picture Settings

- Picture Mode-Preset............................................43

- Auto Colour Tone Control(Cool/Medium/Warm)

44

Manual Picture Adjustment

- Picture Mode-User Option................................45

- Colour Tone - User Option...............................46

-

Picture Improvement Technology

...................47

Advanced - Gamma......................................................48

Advanced - Film Mode ................................................49

Advanced - Black(Darkness) Level...........................50

Advanced - Eye Care ...................................................51

Picture Reset..................................................................52

Power Indicator ............................................................53

Factory Reset.................................................................54

Remote Control Key Functions..................................28

Turning on the TV....................................................... 30

Programme Selection ................................................. 30

Volume Adjustment......................................................30

On Screen Menus Selection and Adjustment.......31

PICTURE CONTROL

WATCHING TV / PROGRAMME CONTROL

AACCCCEESSSSOORRIIEESS

.....................................................1

2

CONTENTS

Front Panel Controls................................................... 4

Back Panel Information .............................................. 5

Stand Installation..........................................................7

Careful Installation Adivice

. . . . . . . . . . . . . . . . . . . .9

Back Cover for Wire Arrangement......................... 10

Swivel Stand................................................................ 11

Positioning your display ............................................11

Kensington Security System ....................................11

Desktop Pedestal Installation ................................. 12

Wall Mount: Horizontal installation....................... 12

Not using the desk-type stand................................13

Antenna Connection ................................................ 14

PREPARATION

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup .......................................................15

DVD Setup..................................................................... 17

VCR Setup..................................................................... 19

Headphone SETUP.......................................................21

Other A/V Source Setup .......................................... 22

External Stereo Setup..................................................23

AV Output Setup ........................................................ 24

Screen Setup ................................................................26

Auto Programme Tuning............................................ 32

Manual Programme Tuning ....................................... 33

Fine Tuning .....................................................................34

Assigning a Station Name ..........................................35

Booster............................................................................36

Programme Edit ........................................................... 37

Favourite Programme .................................................. 38

Selecting the Programme List .................................. 39

Key lock ......................................................................... 40

SOUND & LANGUAGE CONTROL

Auto Volume Leveler ....................................................55

Preset Sound Settings - Sound Mode ....................56

Sound Setting Adjustment - User Mode ...............57

Balance ............................................................................58

TV Speakers On/Off Setup .......................................59

Selecting Audio Out....................................................60

I/II

- Stereo/Dual Reception ....................................... 61

- NICAM Reception ....................................................... 62

- Speaker Sound Output Selection.................... 62

On-Screen Menu Language Selection

...................... 63

3

CONTENTS

APPENDIX

Troubleshooting ............................................................71

Maintenance .................................................................73

Product Specifications ................................................74

IR Codes ....................................................................... 75

TIME SETTING

Clock Setup .....................................................................64

Auto On/Off Timer Setting .........................................65

Sleep Timer Setting .......................................................66

Auto Shut-off Setting...................................................67

TELETEXT

Switch On/Off .............................................................68

SIMPLE Text ...................................................................68

TOP Text .........................................................................69

FASTEXT .........................................................................69

Special Teletext Functions..........................................70

4

FRONT PANEL CONTROLS

PREPARATION

■

This is a simplified representation of the front panel. Image shown may differ from your TV.

■

If your product has a protection film attached, remove the film and then wipe the product with a polishing

cloth.

INPUT MENU PRVOLOK

PROGRAMMEVOLUME

MENU

OK

INPUT

22LF15R

26/32LF15R

POWER

Remote Control Sensor

Power/Standby Indicator

• illuminates red in standby mode.

• illuminates blue when the TV is switched on.

POWER

Remote Control Sensor

Power/Standby Indicator

• illuminates red in standby mode.

• illuminates blue when the TV is switched on.

Note: You can adjust

PPoowweerr IInnddiiccaattoorr

in

the

OPTION menu.

P

MENU

INPUT

OK

+

-

PROGRAMME

VOLUME

OK

MENU

INPUT

5

PREPARATION

BACK PANEL INFORMATION

A

Image shown may differ from your TV.

1

SERVICE ONLY

L

R

Y

P

B

P

R

LR

VIDEO

COMPONENT IN

AUDIO

HDMI IN

H/P

ANTENNA IN

AV IN

VIDEO

AUDIO

Power Cord Socket

This TV operates on an AC power. The voltage is

indicated on the Specifications page. Never

attempt to operate the TV on DC power.

HDMI Input

Connect a HDMI signal to HDMI IN.

SERVICE ONLY PORT

Antenna Input

Connect RF antenna to this jack.

Audio/Video Input (AV IN)

Connect audio/video output from an external

device to these jacks.

Component Input

Connect a component video/audio device to

these jacks.

Headphone Input

Plug the headphone into the headphone socket.

1

2

3

4

5

6

7

2 43

22LF15R

5 6 7

6

PREPARATION

26/32LF15R

1

IN IN

SERVICE ONLY

COMPONENT INCOMPONENT IN

AUDIO

VIDEO

AUDIOAUDIO

ANTENNA

IN

AV

VIDEOVIDEO

IN

OUT

VARIABLE VARIABLE

AUDIO OUTAUDIO OUT

L(MONO)

R

3

2

6

4

Power Cord Socket

This TV operates on an AC power. The voltage is

indicated on the Specifications page. Never

attempt to operate the TV on DC power.

HDMI Input

Connect a HDMI signal to HDMI IN.

SERVICE ONLY PORT

Audio/Video Input (AV IN)

Connect audio/video output from an external

device to these jacks.

AV Output

Connect second TV or monitor to the AV OUT

socket on the

TV.

Variable Audio Output

Connect an external amplifier or add a subwoofer

to your surround sound system.

Component Input

Connect a component video/audio device to

these jacks.

Antenna Input

Connect RF antenna to this jack.

1

2

3

4

5

6

7

5

7

PREPARATION

■

Image shown may differ from your TV

■

When assembling the desk type stand, check whether the bolt is fully tightened. (If not tightened fully, thep

roduct can tilt forward after the product installation.) If you tighten the bolt with excessive force, the boltcan

deviate from abrasion of the tightening part of the bolt.

STAND INSTALLATION

22LF15R

Carefully place the TV screen side down on a cushioned surface to protect the screen from damage.

Assemble the parts of the

SSttaanndd BBooddyy

with

SSttaanndd BBaassee

of the TV. Insert the

SSttaanndd BBooddyy

into a

SSttaanndd BBaassee

until clicking sound.

Assemble the TV as shown.

1

2

3

Stand Body

Stand Base

1

3

4

Carefully place the TV screen side down on a

cushioned surface to protect the screen from

damage.

2

Assemble the parts of the

SSttaanndd BBooddyy

with

the

SSttaanndd BBaassee

of the TV.

Assemble the TV as shown.

Fix the 4 bolts securely using the holes in the

back of the TV.

26/32LF15R

Stand Body

Stand Base

8

PREPARATION

Attaching the TV to a desk (Except for 22LF15R)

The TV must be attached to desk so it cannot be pulled in a forward/backward direction, potentially causing

injury or damaging the product. Use only an attached screw.

1-Screw

(provided as parts of the product)

Desk

Stand

WARNING

!

GG

To prevent TV from falling over, the TV should be securely attached to the floor/wall per installation

instructions. Tipping, shaking, or rocking the machine may cause injury.

9

PREPARATION

CAREFUL INSTALLATION ADVICE

A

You should purchase necessary components to fix the TV safety and secure to the wall from a hardware supplier.

A

Position the TV close to the wall to avoid the possibility of it falling when pushed.

A

The instructions shown below are a safer way to set up the TV, by fixing it to the wall, avoiding the possibility

of it falling forwards if pulled. This will prevent the TV from falling forward and causing injury. This will also pre-

vent the TV from damage. Ensure that children do not climb or hang from the TV.

NOTE

!

G

When moving the TV undo the cords first.

G

Use a platform or cabinet strong and large enough to support the size and weight of the TV.

G

To use the TV safely make sure that the height of the bracket on the wall and on the TV is the same.

3

1

2

Use the eye-bolts or TV brackets/bolts to fix the product to the wall as shown in the picture.

(If your TV has bolts in the eyebolts, loosen then bolts.)

* Insert the eye-bolts or TV brackets/bolts and tighten them securely in the upper holes.

Secure the wall brackets with the bolts on the wall. Match the height of the bracket that is mounted on the

wall.

3

Use a sturdy rope or wire to tie the product for alignment. It is safer to tie the rope so it becomes horizon-

tal between the wall and the product.

2

1

2

1

10

PREPARATION

BACK COVER FOR WIRE ARRANGEMENT

■

Here shown may be somewhat different from your TV.

Connect the cables as necessary.

To connect additional equipment, see the

External Equipment Setup section of the

manual.

1

Install the

CCAABBLLEE MMAANNAAGGEEMMEENNTT CCLLIIPP

as

shown.

2

CABLE MANAGEMENT CLIP

NOTE

!

GG

Do not use the CABLE MANAGEMENT CLIP to lift the TV.

- If the TV is dropped, you may be injured or the TV may be damaged.

How to remove the CABLE MAN-

AGEMENT CLIP

GG

Hold the CABLE MANAGE-

MENT CLIP with both hands

and pull it backward.

22LF15R

26/32LF15R

Connect the cables as necessary.

To connect additional equipment, see the

External Equipment Setup section of the

manual.

1

Open the

CCAABBLLEE MMAANNAAGGEEMMEENNTT CCLLIIPP

as

shown and manage the cables.

2

CABLE MANAGEMENT CLIP

Fit the

CCAABBLLEE MMAANNAAGGEEMMEENNTT CCLLIIPP

as

shown.

3

11

PREPARATION

SWIVEL STAND

(Except for 22LF15R)

After installing the TV, you can adjust the TV manually

to the left or right direction by 20 degrees to suit your

viewing position.

POSITIONING YOUR

DISPLAY (Only 22LF15R)

■

Image shown may differ from your TV.

■

Adjust the position of the panel in various ways for

maximum comfort.

• Tilt range

12

1.5

3

1.5

KENSINGTON SECURITY SYSTEM

(This feature is not available for all models.)

The TV is equipped with a Kensington Security System connector on the back panel. Connect the Kensington

Security System cable as shown below.

For the detailed installation and use of the Kensington Security System, refer to the user’s guide provided with

the Kensington Security System.

For further information, contact http://www.kensington.com, the internet homepage of the Kensington

company. Kensington sells security systems for expensive electronic equipment such as notebook PCs and LCD

projectors.

NOTE

- The Kensington Security System is an optional accessory.

NOTES

a. If the TV feels cold to the touch, there may be a small “flicker”

when when it is turned on.

This is normal, there is nothing wrong with TV.

b. Some minute dot defects may be visible on the screen, appear-

ing as tiny red, green, or blue spots. However, they have no

adverse effect on the monitor's performance.

c. Avoid touching the LCD screen or holding your finger(s)

against it for long periods of time.

Doing so may produce some temporary distortion effects on

the screen.

12

PREPARATION

4 inches

DESKTOP PEDESTAL INSTALLATION

For adequate ventilation allow a clearance of 4”

(10cm) all around the TV.

A

The TV can be installed in various ways such as on

a wall, or on a desktop etc.

A

The TV is designed to be mounted horizontally.

Power Supply

Circuit breaker

EARTHING

Ensure that you connect the earth wire to prevent

possible electric shock. If grounding methods are not

possible, have a qualified electrician install a separate

circuit breaker.

Do not try to earth the TV by connecting it to tele-

phone wires, lightening rods or gas pipes.

WALL MOUNT: HORIZONTAL

INSTALLATION

A

We recommend the use of a LG Brand wall mounting

bracket when mounting the TV to a wall.

A

We recommend that you purchase a wall mounting

bracket which supports VESA standard.

A

LG recommends that wall mounting be performed by a

qualified professional installer.

NOTE

!

G Should Install wall mount on a solid wall perpendicular to

the floor.

G Should use a special wall mount, if you want to install it to

ceiling or slanted wall.

G The surface that wall mount is to be mounted on should

be of sufficient strength to support the weight of TV set;

e.g. concrete, natural rock, brick and hollow block.

G Installing screw type and length depends on the wall

mount used. Further information, refer to the instructions

included with the mount.

G LG is not liable for any accidents or damage to property or

TV due to incorrect installation:

- Where a non-compliant VESA wall mount is used.

- Incorrect fastening of screws to surface which may cause

TV to fall and cause personal injury.

- Not following the recommended Installation method.

4 inches

Model

VESA

(A

*

B)

Standard

Screw

Quantity

22LF15R

26LF15R

32LF15R

100

*

10 0

200

*

10 0

200

*

10 0

M4

4

AA

BB

13

PREPARATION

When installing the wall-mounted unit, use the protection cover.

NOT USING THE DESK-TYPE STAND

22LF15R

Loose the bolts from TV.

1

Pull the

HHIINNGGEE BBOODDYY

backward.

2

Insert the

PPRROOTTEECCTTIIOONN CCOOVVEERR

into

the TV.

3

Fix the 4 bolts securely using the holes in

the back of the TV.

4

PPRROOTTEECCTTIIOONN CCOOVVEERR

HHIINNGGEE BBOODDYY

26/32LF15R

Insert the PROTECTION COVER into the TV

until clicking sound.

14

PREPARATION

HDMI IN HDMI/DVI IN

1

2

RGB IN

COMPONENT IN

AUDIO

ANTENNA

IN

AV

VIDEO

VARIABLE

AUDIO OUT

ANTENNA CONNECTION

■

For optimum picture quality, adjust

antenna direction.

■

An antenna cable and converter are

not supplied.

■

To prevent damage do not connect to the mains outlet until all connections are made between the devices.

HDMI IN HDMI/DVI IN

1

2

RGB IN

COMPONENT IN

AUDIO

ANTENNA

IN

AV

VIDEO

VARIABLE

AUDIO OUT

Multi-family Dwellings/Apartments

(Connect to wall antenna socket)

Single-family Dwellings /Houses

(Connect to wall jack for outdoor antenna)

Outdoor

Antenna

Wall

Antenna

Socket

RF Coaxial Wire (75 ohm)

Antenna

UHF

Signal

Amplifier

VHF

■

In poor signal areas, to achieve better picture quality it may be necessary to install a signal amplifier to the

antenna as shown above.

■

If signal needs to be split for two TVs,use an antenna signal splitter for connection.

15

EXTERNAL EQUIPMENT SETUP

■

To avoid damaging any equipment, never plug in any power cords until you have finished connecting all equipment.

■

Image shown may differ from your TV.

L/MONO

R

AUDIO

VIDEO

VARIABLE

AUDIO OUT

L/MONO

R

AUDIO

VIDEO

VARIABLE AUDIO OUT

HDMI IN HDMI DVI IN

HDMI/DVI IN

1

COMPONENT IN

VIDEO

AUDIO

IN

1 2

HD RECEIVER SETUP

Connecting with a component cable

Connect the video outputs

(

Y, PB, P

R

)

of the digi-

tal set-top box to the

CCOOMMPPOONNEENNTT IINN VVIIDDEEOO

jacks on the TV.

Connect the audio output of the digital set-top

box to the

CCOOMMPPOONNEENNTT IINN AAUUDDIIOO

jacks on

the TV.

Turn on the digital set-top box.

(

Refer to the owner’s manual for the digital set-top

box.

)

Select

CCoommppoonneenntt

input source using the

IINNPPUUTT

button on the remote control.

2

3

4

1

Signal

480i/576i

480p/576p

720p/1080i

1080p

Component

Yes

(Only 50Hz, 60Hz)

HDMI

No

Yes

(22LF15R- Only 50Hz, 60Hz)

(26/32LF15R Only 24Hz, 30Hz, 50Hz, 60Hz)

Y

P

B

P

R

LR

VIDEO

COMPONENT IN

AUDIO

1 2

22LF15R

26/32LF15R

16

EXTERNAL EQUIPMENT SETUP

L/MONO

R

AUDIOAUDIO

VIDEOVIDEO

AV

IN

OUT

VARIABLE

AUDIO OUT

L/MONO

R

AUDIO

VIDEO

VARIABLE AUDIO OUT

HDMI IN HDMI DVI IN

HDMI/DVI IN

1

IN IN

1

Connecting a set-top box with a HDMI cable

Connect the HDMI output of the digital set-top box to the

HHDDMMII IINN

jack on the TV.

Select

HHDDMMII

input source using the

IINNPPUUTT

button on

the remote control.

Turn on the digital set-top box.

(

Refer to the owner’s manual for the digital set-top box.

)

2

3

1

GG

TV can receive the video and audio signal simultaneously

with using a HDMI cable.

GG

If the digital set-top box supports Auto HDMI function,

the output resolution of the source device will be auto-

matically TV to 1280x720p.

GG

If the digital set-top box player does not support Auto

HDMI, you need to TV the output resolution appropri-

ately.

To get the best picture quality, adjust the output resolu-

tion of the source device to 1280x720p .

NOTE

!

HDMI IN

SERVICE ONLY

1

22LF15R

26/32LF15R

17

EXTERNAL EQUIPMENT SETUP

IN

HDMI IN HDMI DVI IN

AV IN 2

L/MONO

R

AUDIO

VIDEO

VARIABLE AUDIO OUT

L/MONO

AUDIO

VIDEO

VARIABLE

AUDIO OUT

COMPONENT IN

VIDEO

AUDIO

R

1 2

DVD SETUP

Connecting with a component cable

Component Input ports

To achieve better picture quality, connect a DVD player to

the component input ports as shown below.

Component ports on the TV

YP

B

P

R

Video output ports

on DVD player

Y

P

B

B-Y

Cb

Pb

P

R

R-Y

Cr

Pr

Connect the video outputs

(

Y, PB, P

R

)

of the DVD to

the

CCOOMMPPOONNEENNTT IINN VVIIDDEEOO

jacks on the TV.

Connect the audio outputs of the DVD to the

CCOOMMPPOONNEENNTT IINN AAUUDDIIOO

jacks on the TV.

Turn on the DVD player, insert a DVD.

Select

CCoommppoonneenntt

input source using the

IINNPPUUTT

button on the remote control.

Refer to the DVD player's manual for operating

instructions.

2

3

4

5

1

Y

P

B

P

R

LR

VIDEO

COMPONENT IN

AUDIO

1 2

22LF15R

26/32LF15R

18

EXTERNAL EQUIPMENT SETUP

IN IN

HDMI IN HDMI DVI IN

AV IN 2

L/MONO

R

AUDIO

VIDEO

VARIABLE AUDIO OUT

L/MONO

AUDIOAUDIO

VIDEOVIDEO

IN

OUT

VARIABLE

AUDIO OUT

R

1

Connecting with a HDMI cable

Connect the HDMI output of the DVD to the

HHDDMMII IINN

jack on the TV.

Select

HHDDMMII

input source using the

IINNPPUUTT

button on the remote control.

Refer to the DVD player's manual for operating

instructions.

1

GG

The TV can receive video and audio signals simultane-

ously when using a HDMI cable.

GG

If the DVD player supports Auto HDMI function, the out-

put resolution of the source device will be automatically

TV to 1280x720p.

GG

If the DVD player does not support Auto HDMI, you

must TV the output resolution appropriately.

To get the best picture quality, adjust the output resolu-

tion of the source device to 1280x720p.

NOTE

!

2

3

HDMI IN HDMI DVI IN

AV IN 2

L/MONO

R

AUDIO

VIDEO

VARIABLE AUDIO OUT

HDMI IN

SERVICE ONLY

1

22LF15R

26/32LF15R

Page is loading ...

LG 22LF15R User manual

LG 22LF15R User manual

Related papers

Other documents