1
ENGLISH
FRANÇAIS
DEUTSCH
ESPAÑOL
ITALIANO
OPERATION AND MAINTENANCE MANUAL
NOTICE D'UTILISATION ET ENTRETIEN
BEDIENUNGSANLEITUNG
MANUAL DE USO Y MANTENIMIENTO
MANUALE D'USO E MANUTENZIONE
HYDRAULIC CUTTING HEAD
TETE COUPE-CABLE HYDRAULIQUE
HYDRAULISCHER SCHNEIDKOPF
CABEZA HIDRAULICA DE CORTE
TESTA OLEODINAMICA DA TAGLIO
TC050
19 M 093
2
(
(
(
(
TG0351
Head type
Tête type
Typ Kopf
Cabeza tipo
Tipo di testa
WARNING LABELS - ETIQUETTES SIGNALETIQUES - WARNSCHILDER -
ETIQUETAS DE ATENCION - ETICHETTE D'AVVERTENZA
1
2
3
123
4
4
– Before using the tool, carefully read instructions in this manual.
– Avant d'utiliser cet outil, lire attentivement les instructions de cette notice.
– Vor Inbetriebnahme unbedingt die Bedienungsanleitung durchlesen.
– Antes de utilizar la herramienta, leer atentamente las instrucciones contenidas en este manual.
– Prima di utilizzare l'utensile, leggere attentamente le istruzioni contenute in questo manuale.
– Keep hands clear of cutting blades.
– Au cours de la coupe, tenir les mains loin des lames.
– Während des Schneidens, die Hände von den Messern fernhalten.
– Durante el corte, tener las manos alejadas de las cuchillas.
– Durante il taglio, tenere le mani lontane dalle lame.
2
– Do not cut steel.
– Ne pas couper l'acier et l'almélec.
– Keinen Stahl schneiden.
– No cortar acero.
– Non tagliare acciaio.
3
4
1
– Always wear safety glasses and gloves when operating this tool.
– Porter toujours les lunettes de protection et les gants de travail.
– Immer mit Schutzbrille und Handschuhen bedienen.
– Trabajar siempre con las gafas y guantes de seguridad.
– Operare sempre con visiera protettiva e guanti da lavoro.
1
2
3
4
Max.pressure
Max. pression
Max. Arbeitsdruck
Presión máxima
Pressione massima
Year
Année
Jahr
Año
Anno
max cutting diam.
ø maxi de coupe
max. Schneid. ø
ø max de corte
ø max di taglio
3
HYDRAULIC CUTTING HEAD
TC050
1. GENERAL CHARACTERISTICS
– Application range: suitable for cutting copper and aluminium cables having a max ø
of ................................................................................................... 50 mm (2 inches)
– Max operating pressure: .............................................................................................. 700 bar (10,000 psi)
– Oil necessary (displacement): ..................................................................................... 38 cm
3
(2.3 cu. in.)
– Dimensions: length ......................................................................................................... 325 mm (12.8 in.)
width .......................................................................................................... 112 mm (4.4 in.)
– Weight: ................................................................................................................................. 3,2 kg (7 lbs)
2. INSTRUCTIONS FOR USE
2.1) Setting (Ref. to Fig. 3)
The head is equipped with a "self-lock"quick male coupler suitable for connection to a hydraulic,
pneumatic or electric pump from the Cembre range.
Insert the conductor between the blades, up to the desired cutting point. For a running conductor,
release the latch (16) and open the tool head.
Fully retract the lower blade (07) before attempting to open the tool head.
With the conductor on the lower blade (07), close the tool head and fully secure the latch (16).
Before commencing the cutting operation ensure that the latch (16) is fully secured: partial
closure may damage the tool head.
2.2) Blade advancement
Operate the pump to advance the lower blade.
Make sure the blades are exactly positioned on the desired cutting point; otherwise re-open the
blades, as § 2.4 and re-position the cutting head.
2.3) Cutting
Continue operating the pump to close the blades and progressively cut the cable.
This head has been specifi cally designed for cutting copper or aluminium cable, do not attempt
to cut steel ropes or steel reinforced cables.
2.4) Blade opening
To open the blades, fully discharge the oil pressure from the pump.
ENGLISH
4
3. MAINTENANCE
The oil pressure inside the head must always be completely released before disconnecting the head
from the hose.
All maintenance operations must be performed with the head disconnected from the hydraulic
pump hose.
The head is robust and requires very little daily maintenance.
Compliance with the following points should help to maintain the optimum performance of the tool.
3.1) Accurate cleaning
Dust, sand and dirt are a danger for any hydraulic device.
Avoid putting the head on muddy or dusty ground. Any dirt particles may score the ram and create
oil leaks.
Every day, after use, the head must be cleaned with a clean cloth, taking care to remove any residual
particles, especially around the moving parts.
3.2) Replacement of the automatic coupler
To replace the automatic coupler proceed as follows:
– Remove the old coupler.
– Carefully clean the thread to remove the old sealant.
– Apply tefl on tape to the thread.
– Fit the new automatic coupler and tighten to 30 Nm (22 lbf ft).
3.3) Storage (Ref. to Fig. 1)
When not in use, the head should be stored and
transported in its canvas bag, to prevent damage.
Canvas bag: type 011; Size 360x137 mm (14.2x5.4 in.)
Weight 0,13 kg (0.3 lbs).
4. BLADES REPLACEMENT (Ref. to Fig. 2)
After extended use, the blades may lose their cutting edge.
Replace the blades as follows:
4.1.1) Lower blade
– Release latch (16) and open the head.
– Operate pump to advance the lower blade until holding screw (17) is visible on the ram (21).
– Using a fl at blade, screwdriver remove the holding screw (17) and release the lower blade (07).
– Insert the new blade and re-fi t the holding screw.
Warning: before closing the head release the oil pressure and retract the lower blade, otherwise
the tool head assembly may hit and damage the lower blade.
ENGLISH
FIG. 1
5
The items marked () are those Cembre recommends replacing if the head is disassembled.
These items are supplied on request in the “TC050 Spare Parts Package”.
The guarantee is void if parts used are not Cembre original spares.
When ordering spare parts always specify the following:
- code number of item
- description of item
- type of head
- head serial number
6. RETURN TO Cembre FOR OVERHAUL
In the case of a breakdown contact our Area Agent who will advise you on the problem and give
you the necessary instructions on how to dispatch the tool to our nearest service Centre; if possible,
attach a copy of the Test Certifi cate supplied by Cembre together with the tool or fi ll in and attach
the form available in the “ASSISTANCE” section of the Cembre website.
ENGLISH
4.1.2) Upper blade
– Release latch (16) and open the head.
– Remove the circlip (05) and extract the head pivot (08), enough to release the tool head assembly.
– Remove circlip (29) and pivot (30), to release the latch (16). Remove latch spring (15) from the
right hand guide (14).
– Unscrew the 4 screws (09), remove the left hand guide (11), the right hand guide (14) and release
the blade (12).
– Fit the left and right hand guides to the new blade. Place the spring (15) into its seat and re-fi t
the latch (16).
– Fit the blade assembly to the head (06), fully insert the pivot (08) and secure with the circlip (05).
5. PARTS LIST (Ref. to Fig. 3)
Code N° Item DESCRIPTION Qty
6900334 18 M 6x30 SCREW 1
6080051 19 GUIDE BUSH 1
6522314 20 BLADE RETURN SPRING 1
6620171 21 RAM 1
6040181
22
BACK-UP RING 1
6360270
23
O-RING 1
6360266
24
O-RING 1
6120195 25 CYLINDER 1
6232000 26 (TG 0351) LABEL 1
6230820 27 (TG 0120) METAL LABEL 1
6650118 28 ø 2,5x3,5 PIN 2
6700140
29
CIRCLIP 1
6560701
30
LATCH PIVOT 1
6800186 31 PROTECTION CAP 1
6860131
COMPLETE HEAD
6000027
SPARE PARTS PACKAGE
Code N° Item DESCRIPTION Qty
6060120 01 Q14-MS COUPLER 1
6340082 02 M6x8 GRUB SCREW 1
6361810
03
SEAL 1
6641020
04
M6 COPPER WASHER 1
6040421
05
ø 10 CIRCLIP 1
6860101 06 HEAD 1
6420231 07 LOWER BLADE 1
6560691 08 UPPER BLADE PIVOT 1
6900315
09
M 6x16 SCREW 4
6370141
11
LOWER BLADE LEFT HAND GUIDE
1
6420241
12
UPPER BLADE 1
6370151
14
LOWER BLADE RIGHT HAND GUIDE
1
6520460
15
SPRING 1
6200051
16
LATCH 1
6370250 17 HOLDING SCREW 1
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
18
FIG. 2
BLADE REPLACEMENT - CHANGEMENT DES LAMES - SCHNEIDMESSERWECHSEL - CAMBIO CUCHILLAS - CAMBIO LAME
16
09
08
05
12
17
14
11
29
07
06
21
30
16
07
Page is loading ...
20
This manual is the property of Cembre: any reproduction is forbidden without written permission.
Ce manuel est la proprieté de Cembre: toute reproduction est interdite sauf autorisation écrite.
Diese Bedienungsanleitung ist Eigentum der Firma Cembre.
Ohne vorherige schriftliche Genehmigung darf die Bedienungsanleitung weder vollständig noch teilweise vervielfältigt werden.
Este manual es propiedad de Cembre. Toda reproducción está prohibida sin autorización escrita.
Questo manuale è di proprietà della Cembre: ogni riproduzione é vietata se non autorizzata per scritto.
cod. 6261080
Cembre Ltd.
Dunton Park
Kingsbury Road, Curdworth - Sutton Coldfield
West Midlands B76 9EB (UK)
Tel.: 01675 470440 - Fax: 01675 470220
E-mail: [email protected]
www.cembre.co.uk
Cembre S.p.A.
Via Serenissima, 9
25135 Brescia (Italia)
Telefono: 030 36921
Telefax: 030 3365766
E-mail: [email protected]
www.cembre.com
Cembre S.a.r.l.
22 Avenue Ferdinand de Lesseps
91420 Morangis (France)
Tél.: 01 60 49 11 90 - Fax: 01 60 49 29 10
CS 92014 - 91423 Morangis Cédex
E-mail: [email protected]
www.cembre.fr
Cembre España S.L.U.
Calle Verano 6 y 8
28850 Torrejón de Ardoz
Madrid (España)
Teléfono: 91 4852580 - Fax: 91 4852581
E-mail: [email protected]
www.cembre.es
Cembre GmbH
Heidemannstraße 166
80939 München (Deutschland)
Telefon: 089 3580676
Telefax: 089 35806777
E-mail: [email protected]
www.cembre.de
Cembre Inc.
Raritan Center Business Park
181 Fieldcrest Avenue
Edison, New Jersey 08837 (USA)
Tel.: (732) 225-7415 - Fax: (732) 225-7414
E-mail: [email protected]
www.cembreinc.com
www.cembre.com
IKUMA GmbH & Co. KG
Boschstraße 7
71384 Weinstadt (Deutschland)
Telefon: 07151 20536-60
Telefax: 07151 20536-80
E-mail: [email protected]
www.ikuma.de
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
in other languages
- italiano: Cembre TC050 Manuale utente
- français: Cembre TC050 Manuel utilisateur
- español: Cembre TC050 Manual de usuario
- Deutsch: Cembre TC050 Benutzerhandbuch