Page is loading ...
ITALIANO
AVVERTENZE PER L’INSTALLATORE
OBBLIGHI GENERALI PER LA SICUREZZA
ATTENZIONE! È importante per la sicurezza delle persone seguire
attentamente tutta l’istruzione. Una errata installazione o un errato
uso del prodotto può portare a gravi danni alle persone.
Leggere attentamente le istruzioni prima di iniziare l’installazione del prodotto.
I materiali dell’imballaggio (plastica, polistirolo, ecc.) non devono essere lasciati alla
portata dei bambini in quanto potenziali fonti di pericolo.
Conservare le istruzioni per riferimenti futuri.
Questo prodotto è stato progettato e costruito esclusivamente per l’utilizzo indicato in
questa documentazione. Qualsiasi altro utilizzo non espressamente indicato potrebbe
pregiudicare l’integrità del prodotto e/o rappresentare fonte di pericolo.
GENIUS declina qualsiasi responsabilità derivata dall’uso improprio o diverso da quello
per cui l’automatismo è destinato.
Non installare l’apparecchio in atmosfera esplosiva: la presenza di gas o fumi
infiammabili costituisce un grave pericolo per la sicurezza.
Gli elementi costruttivi meccanici devono essere in accordo con quanto stabilito
dalle Norme EN 12604 e EN 12605.
Per i Paesi extra-CEE, oltre ai riferimenti normativi nazionali, per ottenere un livello di
sicurezza adeguato, devono essere seguite le Norme sopra riportate.
GENIUS non è responsabile dell’inosservanza della Buona Tecnica nella costru-
zione delle chiusure da motorizzare, nonché delle deformazioni che dovessero
intervenire nell’utilizzo.
L’installazione deve essere effettuata nell’osservanza delle Norme EN 12453 e EN
12445. Il livello di sicurezza dell’automazione deve essere C+D.
Prima di effettuare qualsiasi intervento sull’impianto, togliere l’alimentazione elettrica
e scollegare le batterie.
Prevedere sulla rete di alimentazione dell’automazione un interruttore onnipolare con
distanza d’apertura dei contatti uguale o superiore a 3 mm. È consigliabile l’uso di
un magnetotermico da 6A con interruzione onnipolare.
Verificare che a monte dell’impianto vi sia un interruttore differenziale con soglia
da 0,03 A.
Verificare che l’impianto di terra sia realizzato a regola d’arte e collegarvi le parti
metalliche della chiusura.
L’automazione dispone di una sicurezza intrinseca antischiacciamento costituita
da un controllo di coppia. E’ comunque necessario verificarne la sogli di intervento
secondo quanto previsto dalle Norme indicate al punto 10.
I dispositivi di sicurezza (norma EN 12978) permettono di proteggere eventuali
aree di pericolo da Rischi meccanici di movimento, come ad Es. schiacciamento,
convogliamento, cesoiamento.
Per ogni impianto è consigliato l’utilizzo di almeno una segnalazione luminosa nonché
di un cartello di segnalazione fissato adeguatamente sulla struttura dell’infisso, oltre
ai dispositivi citati al punto “16”.
GENIUS declina ogni responsabilità ai fini della sicurezza e del buon funzionamento
dell’automazione, in caso vengano utilizzati componenti dell’impianto non di
produzione GENIUS.
Per la manutenzione utilizzare esclusivamente parti originali GENIUS.
Non eseguire alcuna modifica sui componenti facenti parte del sistema d’au-
tomazione.
L’installatore deve fornire tutte le informazioni relative al funzionamento manuale
del sistema in caso di emergenza e consegnare all’Utente utilizzatore dell’impianto
il libretto d’avvertenze allegato al prodotto.
Non permettere ai bambini o persone di sostare nelle vicinanze del prodotto
durante il funzionamento.
L’applicazione non può essere utilizzata da bambini, da persone con ridotte ca-
pacità fisiche, mentali, sensoriali o da persone prive di esperienza o del necessario
addestramento.
Tenere fuori dalla portata dei bambini radiocomandi o qualsiasi altro datore di impul-
so, per evitare che l’automazione possa essere azionata involontariamente.
Il transito tra le ante deve avvenire solo a cancello completamente aperto.
L’utente utilizzatore deve astenersi da qualsiasi tentativo di riparazione o d’intervento
e deve rivolgersi solo ed esclusivamente a personale qualificato GENIUS o centri
d’assistenza GENIUS.
Tutto quello che non è previsto espressamente in queste istruzioni non è permesso.
ENGLISH
IMPORTANT NOTICE FOR THE INSTALLER
GENERAL SAFETY REGULATIONS
ATTENTION! To ensure the safety of people, it is important that you read
all the following instructions. Incorrect installation or incorrect use
of the product could cause serious harm to people.
Carefully read the instructions before beginning to install the product.
Do not leave packing materials (plastic, polystyrene, etc.) within reach of children
as such materials are potential sources of danger.
Store these instructions for future reference.
This product was designed and built strictly for the use indicated in this documen-
tation. Any other use, not expressly indicated here, could compromise the good
condition/operation of the product and/or be a source of danger.
GENIUS declines all liability caused by improper use or use other than that for which
the automated system was intended.
Do not install the equipment in an explosive atmosphere: the presence of inflam-
mable gas or fumes is a serious danger to safety.
The mechanical parts must conform to the provisions of Standards EN 12604 and
EN 12605.
For non-EU countries, to obtain an adequate level of safety, the Standards mentioned
above must be observed, in addition to national legal regulations.
GENIUS is not responsible for failure to observe Good Technique in the construction
of the closing elements to be motorised, or for any deformation that may occur
during use.
The installation must conform to Standards EN 12453 and EN 12445. The safety level
of the automated system must be C+D.
Before attempting any job on the system, cut out electrical power and disconnect
the batteries.
The mains power supply of the automated system must be fitted with an all-pole
switch with contact opening distance of 3mm or greater. Use of a 6A thermal breaker
with all-pole circuit break is recommended.
Make sure that a differential switch with threshold of 0.03 A is fitted upstream of
the system.
Make sure that the earthing system is perfectly constructed, and connect metal parts
of the means of the closure to it.
The automated system is supplied with an intrinsic anti-crushing safety device
consisting of a torque control. Nevertheless, its tripping threshold must be checked
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
as specified in the Standards indicated at point 10.
The safety devices (EN 12978 standard) protect any danger areas against mechanical
movement Risks, such as crushing, dragging, and shearing.
Use of at least one indicator-light is recommended for every system, as well as a
warning sign adequately secured to the frame structure, in addition to the devices
mentioned at point “16”.
GENIUS declines all liability as concerns safety and efficient operation of the automa-
ted system, if system components not produced by GENIUS are used.
For maintenance, strictly use original parts by GENIUS.
Do not in any way modify the components of the automated system.
The installer shall supply all information concerning manual operation of the system
in case of an emergency, and shall hand over to the user the warnings handbook
supplied with the product.
Do not allow children or adults to stay near the product while it is operating.
The application cannot be used by children, by people with reduced physical, mental,
sensorial capacity, or by people without experience or the necessary training.
Keep remote controls or other pulse generators away from children, to prevent the
automated system from being activated involuntarily.
Transit through the leaves is allowed only when the gate is fully open.
The User must not in any way attempt to repair or to take direct action and must solely
contact qualified GENIUS personnel or GENIUS service centres.
Anything not expressly specified in these instructions is not permitted.
FRANÇAIS
CONSIGNES POUR L’INSTALLATEUR
RÈGLES DE SÉCURITÉ
ATTENTION! Il est important, pour la sécurité des personnes, de suivre
à la lettre toutes les instructions. Une installation erronée ou un
usage erroné du produit peut entraîner de graves conséquences
pour les personnes.
Lire attentivement les instructions avant d’installer le produit.
Les matériaux d’emballage (matière plastique, polystyrène, etc.) ne doivent pas
être laissés à la portée des enfants car ils constituent des sources potentielles
de danger.
Conserver les instructions pour les références futures.
Ce produit a été conçu et construit exclusivement pour l’usage indiqué dans cette
documentation. Toute autre utilisation non expressément indiquée pourrait compro-
mettre l’intégrité du produit et/ou représenter une source de danger.
GENIUS décline toute responsabilité qui dériverait d’usage impropre ou différent de
celui auquel l’automatisme est destiné.
Ne pas installer l’appareil dans une atmosphère explosive: la présence de gaz ou de
fumées inflammables constitue un grave danger pour la sécurité.
Les composants mécaniques doivent répondre aux prescriptions des Normes EN
12604 et EN 12605.
Pour les Pays extra-CEE, l’obtention d’un niveau de sécurité approprié exige non
seulement le respect des normes nationales, mais également le respect des
Normes susmentionnées.
GENIUS n’est pas responsable du non-respect de la Bonne Technique dans la con-
struction des fermetures à motoriser, ni des déformations qui pourraient intervenir
lors de l’utilisation.
L’installation doit être effectuée conformément aux Normes EN 12453 et EN 12445.
Le niveau de sécurité de l’automatisme doit être C+D.
Couper l’alimentation électrique et déconnecter la batterie avant toute interven-
tion sur l’installation.
Prévoir, sur le secteur d’alimentation de l’automatisme, un interrupteur omnipolaire
avec une distance d’ouverture des contacts égale ou supérieure à 3 mm. On recom-
mande d’utiliser un magnétothermique de 6A avec interruption omnipolaire.
Vérifier qu’il y ait, en amont de l’installation, un interrupteur différentiel avec un
seuil de 0,03 A.
Vérifier que la mise à terre est réalisée selon les règles de l’art et y connecter les
pièces métalliques de la fermeture.
L’automatisme dispose d’une sécurité intrinsèque anti-écrasement, formée d’un
contrôle du couple. Il est toutefois nécessaire d’en vérifier le seuil d’intervention
suivant les prescriptions des Normes indiquées au point 10.
Les dispositifs de sécurité (norme EN 12978) permettent de protéger des zones
éventuellement dangereuses contre les Risques mécaniques du mouvement, comme
l’écrasement, l’acheminement, le cisaillement.
On recommande que toute installation soit doté au moins d’une signalisation lumi-
neuse, d’un panneau de signalisation fixé, de manière appropriée, sur la structure
de la fermeture, ainsi que des dispositifs cités au point “16”.
GENIUS décline toute responsabilité quant à la sécurité et au bon fonctionnement
de l’automatisme si les composants utilisés dans l’installation n’appartiennent pas
à la production GENIUS.
Utiliser exclusivement, pour l’entretien, des pièces GENIUS originales.
Ne jamais modifier les composants faisant partie du système d’automatisme.
L’installateur doit fournir toutes les informations relatives au fonctionnement manuel du
système en cas d’urgence et remettre à l’Usager qui utilise l’installation les “Instructions
pour l’Usager” fournies avec le produit.
Interdire aux enfants ou aux tiers de stationner près du produit durant le fonc-
tionnement.
Ne pas permettre aux enfants, aux personennes ayant des capacités physiques,
mentales et sensorielles limitées ou dépourvues de l’expérience ou de la formation
nécessaires d’utiliser l’application en question.
Eloigner de la portée des enfants les radiocommandes ou tout autre générateur
d’impulsions, pour éviter tout actionnement involontaire de l’automatisme.
Le transit entre les vantaux ne doit avoir lieu que lorsque le portail est complète-
ment ouvert.
L’utilisateur doit s’abstenir de toute tentative de réparation ou d’intervention et
doit s’adresser uniquement et exclusivement au personnel qualifié GENIUS ou aux
centres d’assistance GENIUS.
Tout ce qui n’est pas prévu expressément dans ces instructions est interdit.
ESPAÑOL
ADVERTENCIAS PARA EL INSTALADOR
REGLAS GENERALES PARA LA SEGURIDAD
ATENCION! Es sumamente importante para la seguridad de las
personas seguir atentamente las presentes instrucciones. Una
instalación incorrecta o un uso impropio del producto puede
causar graves daños a las personas.
Lean detenidamente las instrucciones antes de instalar el producto.
Los materiales del embalaje (plástico, poliestireno, etc.) no deben dejarse al alcance
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
1.
2.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
4
ENGLISH
CE DECLARATION OF CONFORMITY
Manufacturer: GENIUS S.p.A.
Address: Via Padre Elzi, 32 - 24050 - Grassobbio- Bergamo - ITALY
Declares that: The opto-electronic active protection device mod. VEGA WIRELESS,
conforms to the essential safety requirements of the following EEC directives:
2006/95/EC Low Voltage directive.
2004/108/EC Electromagnetic Compatibility Directive.
Additional information:
This product underwent a test in a typical uniform configuration (all products manufactured by GENIUS S.p.A.).
Grassobbio, 10-10-2007
Managing Director
D. Gianantoni
•
•
•
Notes on reading the instruction
Read this installation manual to the full before you begin installing the product.
The symbol
indicates notes that are important for the safety of persons and for the good condition of the
automated system.
The symbol
draws your attention to the notes on the characteristics and operation of the product.
INDEX
WARNINGS page.5
1. DESCRIPTION AND TECHNICAL SPECIFICATIONS page.5
2. DIMENSIONS page.5
3. INSTALLATION page.5
4. ELECTRICAL CONNECTIONS page.5
5. START-UP page.5
6. TROUBLESHOOTING page.6
5
ENGLISH
VEGA WIRELESS
WARNINGS
For the safety of people, it is important that all the
instructions be carefully observed
Incorrect installation or incorrect use of the product
could cause serious harm to people.
Carefully read the instructions before beginning
to install the product and keep them for future
reference.
1. DESCRIPTION AND TECHNICAL
SPECIFICATIONS
The pair of self-aligning photocells, XP15 W, is composed
of an infrared transmitter and receiver synchronised to
four selectable channels.
The XP15 W photocell is an auxiliary safety device.
Darkening the light beam produces a change of state
of the receiver, which sends the signal of the photocell
involved by means of a relay contact.
The transmitter of the pair is powered by a battery but it
can also be powered from the mains supply.
Selection of the transmission channel permits up to 4
pairs of XP15 W photocells to be installed on the same
unit, eliminating the risk of interference between one
pair and another.
Power supply
12 - 24 V~.
12 - 24 Vdc
Absorbed current RX 30 mA
Absorbed current TX
40 µA with Battery
5 mA at 24 Vdc
Type and Life of battery TX
CR2 , 3 V
from 2 to 3 years
쐃
Maximum range 15 m
Protection class IP54
Obstacle detection time 40 ms
Method of alignment automatic
Self-alignment angle
+/- 7° (15 m)
+/- 13° (5 m.)
Transmission of signal 4 selectable channels
Operating ambient tem-
perature
-20 ... +55 °C
Installation
on wall or column instal-
lation
햲
The battery life can vary depending on the charge of
the battery used, its type and installation/environmental
conditions.
2. DIMENSIONS
The Transmitter and Receiver are the same size and are
shown in Figure 1.
3. INSTALLATION
For correct operation, the positions of the Receiver and
Transmitter should be aligned.
The Receiver of the XP15 W pair of photocells can be
installed in two possible ways:
On wall with the sheath walled in (Fig. 2).
On wall with an external tube/sheath (Fig. 3).
Carry out the preparations for the electrical connec-
tions.
Fix the body of the receiver using the appropriate
screws and rawlplugs.
The Transmitter of the XP15 W pair of photocells can be
powered by an internal battery (Fig. 4) or can also be
powered from the mains supply.
The battery-powered Transmitter only requires fixing, either
on wall or column.
If the Transmitter is powered from the mains supply,
follow the same types of installation indicated in figures
2 and 3.
4. ELECTRICAL CONNECTIONS
Make the electrical connections to the terminal boards
of the receiver as indicated in Fig. 5.
The power supply terminals of the Receiver can
be connected to a 12 or 24 Volt supply, either
direct (DC) or alternating current ( ~ ).
f it is intended to perform the FAIL SAFE check
with a battery-powered Transmitter, connect
the FAIL SAFE (-TX FSW) terminal of the FAAC
control boards to the MINUS ( – ) terminal of
the photocell Receiver.
If the Transmitter is mains powered, follow the indications
in Fig. 6.
The power supply terminals of the Transmitter can
be connected to a 12 or 24 Volt source, either
direct (DC) or alternating ( ~ ) current.
On switching on the Transmitter and the Receiver, the
respective DL2 LEDs will light up for 1 second.
5. START-UP
Before closing the pair of photocells with their respective
closing plugs, it is indispensable to select the transmission
channel and check its functioning through the indicator
LEDs located on the Receiver.
SELECTION OF THE TRANSMISSION CHANNEL
Power up the photocells and select the transmission
channel by pressing button P1 and keeping it pressed
for 5 seconds (fig. 7).
At the end of the 5 seconds, the DL2 LED in figure 7 will
flash the number of times corresponding to the channel
set, then switching itself off for 1 second before repea-
ting the process. After completing 3 indications of the
channel set, the procedure terminates and the channel
is memory stored.
Whilst this is displaying, it is possible to change the tran-
smission channel: by pressing button P1, the four channels
are selected in succession.
1.
2.
•
•
6
ENGLISH
Check the number of flashes of the DL2 LED to determine
which channel has been selected:
1 flash = Channel 1
2 flashes = Channel 2
3 flashes = Channel 3
4 flashes = Channel 4
Set the same channel on both receiver and tran-
smitter.
Whilst the channel set is being displayed, the
pair of photocells is inactive and its contact is
therefore OPEN. Wait for the end of the display
to operate the automated system.
CHECKING THE INDICATOR LEDS FOR THE RX
The states and significance of the LEDs on the Receiver are
shown below; refer to figure 8 to find their position.
DL 1 Power supply
ON Power on
OFF Power off
DL 2 Transmission channel and charge of the TX battery
ON TX Battery OK
Slow flashing Indication of transmission channel
Rapid flashing TX Battery almost discharged
OFF
TX battery flat or Photocell en-
gaged
DL 3 Alignment
ON Alignment OK
Slow flashing Alignment not correct
OFF
Non-alignment or Photocell en-
gaged
CHECKING THE INDICATOR LEDs FOR THE TX
The states and significance of the LEDs on the Transmitter
are shown below; refer to figure 9 to find their position.
DL 1 Power supply
ON Mains power supply on
OFF
Mains power supply off, battery
operation
DL 2 Transmission channel
OFF Normal Operation
Slow flashing
Display of the transmission chan-
nel
Complete the installation by closure of the photocells just
installed with the appropriate four-screw closing plug,
being careful to position the rubber separator (indicated
in figs. 2, 3 ref. 햲) so as to ensure the correct degree of
IP insulation.
6. TROUBLESHOOTING
Help with the identification and resolution of particular conditions regarding operation of the photocells is given
below.
For a complete list of the error/breakdown situations, refer to the instructions for the control unit used to move the
application.
CONDITION CAUSE/PROBLEM SUGGESTION
The gate does not move. The DL2 and
DL3 Receiver LEDs are off.
- Non-alignment
- The Transmitter is not receiving
power
- Incorrect choice of transmission
channel.
- Check the selection of the transmis-
sion channel.
- Check the power supply to the pair
of photocells.
- Check the alignment of the pair.
The DL2 Receiver LED flashes.
Incorrect power supply to the Tran-
smitter.
- Replace the battery inside the
Transmitter.
- If the Transmitter is mains powered,
check the voltage.
The DL3 Receiver LED flashes
The photocells are not correctly ali-
gned.
- Adjust the alignment of the pho-
tocells.
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Le descrizioni e le illustrazioni del presente manuale non sono impegnative. GENIUS si riserva il diritto, lasciando inal-
terate le caratteristiche essenziali dell’apparecchiatura, di apportare in qualunque momento e senza impegnarsi
ad aggiornare la presente pubblicazione, le modifiche che essa ritiene convenienti per miglioramenti tecnici o per
qualsiasi altra esigenza di carattere costruttivo o commerciale.
The descriptions and illustrations contained in the present manual are not binding. GENIUS reserves the right, whils
leaving the main features of the equipments unaltered, to undertake any modifications to holds necessary for either
technical or commercial reasons, at any time and without revising the present publication.
Les descriptions et les illustrations du présent manuel sont fournies à titre indicatif. GENIUS se réserve le droit d’apporter
à tout moment les modifications qu’elle jugera utiles sur ce produit tout en conservant les caractéristiques essentielles,
sans devoir pour autant mettre à jour cette publication .
Las descripciones y las ilustraciones de este manual no comportan compromiso alguno. GENIUS se reserva el de-
recho, dejando inmutadas las características esenciales de los aparatos, de aportar, en cualquier momento y sin
comprometerse a poner al día la presente publicación, todas las modificaciones que considere oportunas para el
perfeccionamiento técnico o para cualquier otro tipo de exigencia de carácter constructivo o comercial.
Die Beschreibungen und Abbildungen in vorliegendem Handbuch sind unverbindlich. GENIUS behält sich das Recht
vor, ohne die wesentlichen Eigenschaften dieses Gerätes zu verändern und ohne Verbindlichkeiten in Bezung auf
die Neufassung der vorliegenden Anleitungen, technisch bzw, konstruktiv / kommerziell bedingte Verbesserungen
vorzunehmen.
De beschrijvingen in deze handleiding zijn niet bindend. GENIUS behoudt zich het recht voor op elk willekeurig moment
de veranderingen aan te brengen die het bedrijf nuttig acht met het oog op technische verbeteringen of alle mogelijke
andere productie- of commerciële eisen, waarbij de fundamentele eigenschappen van het apparaat gehandhaafd
blijven, zonder zich daardoor te verplichten deze publicatie bij te werken.
Timbro rivenditore: / Distributor’s stamp: / Timbre de l’agent: / Sello del revendedor: / Fachhändlerstempel: /
Stempel dealer:
Via Padre Elzi, 32
24050 - Grassobbio
BERGAMO-ITALY
tel. 0039.035.4242511
fax. 0039.035.4242600
www.geniusg.com
00058I0800 Rev.0
/
