Laser AO-SHRED01 Quick start guide
- Category
- Paper shredders
- Type
- Quick start guide
AO-SHRED01 QUICK START GUIDE
1
WHAT’S IN THE BOX
One Paper Shredder, One Quick Start Guide
FEATURES AND OPERATION
Shredder head and waste bin
Place the shredder head onto the waste collection bin, ensuring they align correctly. If the shredder head is not
orientated correctly on the waste bin, the shredder will not operate correctly.
Operation and usage
- Do not feed more than 8 sheets of standard 80g A4 office paper or 1 credit card at once through the shredder
- Smaller items like envelopes, credit cards or receipts should all be passed through the center of the feed slot.
- It is safe to feed paper with staples through this machine, however to prolong the life of the unit it is suggested that
staples be removed where possible
- Do not feed paper clips through the machine as they will jam the machine and cause irreparable damage.
Operation mode switch
AUTO: This mode will start and stop automatically when an item is inserted into the paper feed slot
REV: This mode is used to clear paper jams. Cutters will immediately engage in the opposite
direction until another mode is selected.
OFF: This mode powers the machine off. This position is recommended when emptying the waste bin or
when the shredder is not in use for prolonged periods of time.
Safety protection
- This shredder is equipped with motor overload protection.
- The unit should be allowed to cool down and not used for 30 mins, if used continuously for two minutes.
- Power may automatically be cut to the unit if:
> The unit is operated continuously at maximum capacity for longer than 2 minutes
> Overloading the unit such as shredding more than 8 sheets at one time
> Paper is not fed squarely into the feed slot.
Safety power-off
If the safety protection has cut power to the machine during use, you should:
- Switch the shredder off and unplug it from mains power. Wait at least 30 minutes for the overload protection to
reset.
- During this time you can tear off or cut any excess paper from the top of the shredder where possible
- Plug the unit back into mains power and put the unit into REV mode. Carefully pull the remaining paper
from the cutting heads.
- Once the unit is free from jams, place the mode switch back to the AUTO position and continue normal use
Note: Particularly difficult jams can be dislodged by moving between the AUTO and REV settings
Maintenance
- Regularly emptying your waste bin helps avoid shredded paper jamming the cutters from underneath.
- When you empty the shredder waste bin or clear a paper jam, please make sure the unit is switched off and
unplugged from mains power
Warning: Do not use this product for any other purpose aside from those explained above. Keep loose articles of
clothing and foreign objects away from the shredder while in use. This device is not suitable for use by children
under the age of 15.
AO-SHRED01 QUICK START GUIDE
2
FAQ
Q1. My shredder does not work after paper is inserted.
A1. Check that the power cord has been connected properly to the shredder and also to mains power
A2. The motor may have over-heated. Wait for about 30 minutes or until the safety switch has engaged power
back to the unit.
A3. The paper feed may be jammed. Reverse the paper feed and remove any jammed paper
A4. The shredder head is not placed properly on the basket. Place the shredder head securely on the basket
and in the correct orientation
Q2. The shredder does not shred paper
A1. Too much paper may have been fed through. Check to see if you have exceeded the rated capacity of paper
A2. The paper size inserted may be larger than the paper entry and has folded over causing a jam. Reverse the
shredder and take the paper out.
Q3. I have finished putting paper though the machine but it will not turn off
A1. There is a sensor in the centre of the paper feed slot that either turns the unit or off when triggered by
inserting paper. If a piece of paper has lodged itself around this sensor, the unit may not turn off correctly.
In this case follow the paper jam procedures above being careful not to damage the sensor
For further product information and instruction please visit our product web page at
www.laserco.net or email support@laserco.com.au
Please note: As continual improvements are made to this product, slight operational differences may
occur. For the most up-to-date user manual, please visit our web site.
AO-SHRED01 QUICK START GUIDE
3
Warranty Against Defects
Laser Corporation Pty Ltd (“Laser”) warrants your new product to be free from defects in materials and workmanship
for 12 months, from the date of purchase, provided that the product is used in accordance with accompanying
recommendations or instructions where provided. The benefit of this warranty is in addition to your rights under the
Australian Consumer Law and to other rights and remedies of the consumer under a law in relation to the goods or
services to which the warranty relates.
Through a network of retailers and resellers, Laser will provide you with your choice of a refund, repair or exchange
(where possible) for this product if it becomes defective within the warranty period. This warranty will no longer
apply where the defect is a result of alteration, accident, misuse, abuse, normal wear and tear, neglect or improper
storage.
Please retain your receipt as proof of purchase
How to make a product warranty claim:
Step 1: Find your receipt which proves the date of purchase. Where the date of purchase cannot be verified, your
place of purchase or Laser will make an assessment based on the date of manufacture, the condition of the Laser
Product and the type of defect.
Step 2a): Contact your place of purchase. They will assess the nature of the fault and refund or replace the product
as per their store refund or warranty policy.
Step 2b): If your place of purchase cannot be contacted, then you can contact Laser . Customer Service with details
of your defective Laser Product: Phone: (02) 9870 3355; or Email: service@laserco.com.au or online
www.laserco.net/support/warranty (click on “Consumers (End Users)”). Our business address is at 1/6-8 Byfield
Street, North Ryde, NSW 2113
Step 3: Laser . will issue you with a Return Authorisation (RA) number within 48 hours. When requested, send us
the defective Product and a copy of your receipt. Laser will cover the cost of the return delivery.
Step 4: Wait for us to contact you. Once we have received your defective Laser Product for inspection, we will
inform you of our assessment of your claim within 7 days. When we contact you, we will firstly let you know whether
you have a valid claim under this Warranty, and if so, we will inform you whether your defective Laser Product will
be replaced or repaired, together with the number of days you can expect to wait to receive your replaced or
repaired Laser Product.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a
replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.
You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
-
1
-
2
-
3
Laser AO-SHRED01 Quick start guide
- Category
- Paper shredders
- Type
- Quick start guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
