Silencer Silencer SL-2 Installation guide

Silencer
Brand
Silencer
Model
Silencer SL-2
Category
Motor vehicle electronics
Type
Installation guide

This manual is also suitable for

Silencer SL-2 is a 2-Channel Security System with Keyless Entry that provides professional-grade protection for your vehicle. The system boasts a range of advanced features designed to enhance your vehicle's security and convenience. With its programmable options, you can customize the system to meet your specific needs. Here are some of the key features and possible use cases:

  • 2-Channel Security: The system provides two independent security channels, allowing you to monitor and protect different areas of your vehicle separately.

  • Keyless Entry: The integrated keyless entry system lets you lock and unlock your vehicle remotely, providing added convenience and security.

Silencer SL-2 is a 2-Channel Security System with Keyless Entry that provides professional-grade protection for your vehicle. The system boasts a range of advanced features designed to enhance your vehicle's security and convenience. With its programmable options, you can customize the system to meet your specific needs. Here are some of the key features and possible use cases:

  • 2-Channel Security: The system provides two independent security channels, allowing you to monitor and protect different areas of your vehicle separately.

  • Keyless Entry: The integrated keyless entry system lets you lock and unlock your vehicle remotely, providing added convenience and security.

1
PROFESSIONAL SERIES
IM_FULL_SL2_REV_B
PROFESSIONAL SERIES
INSTALLATION MANUAL
This unit is designed for professional installation only and must be
installed by an authorized Silencer dealer.
Magnadyne Corporation 1111 W. Victoria Street, Compton CA 90220 (800) 340-3200
For Warranty information:
Please visit our website at www.silencer.com
SL- 2
2-Channel Security
with Keyless Entry System
2
PROFESSIONAL SERIES
IM_FULL_SL2_REV_B
INSTALLATION DIAGRAM
3
PROFESSIONAL SERIES
IM_FULL_SL2_REV_B
MAIN POWER CONNECTOR
RED / WHITE: PARKING LIGHT RELAY INPUT
WHITE: PARKING LIGHT OUTPUT
BLACK : MAIN SYSTEMS GROUND
BROWN : POSITIVE SIREN OUTPUT
RED : FUSED 12 VOLT (+) BATTERY POWER
3 PIN, DOOR LOCK CONNECTOR
1. Blue
Wire
3. Green
Wire
( - ) Lock Pulse
( + ) Unlock Pulse
( - ) Unlock Pulse
(+) Lock Pulse
7 PIN ACCESSORY CONNECTOR
- GRAY WIRE / CHANNEL 3 NEGATIVE TRUNK OUTPUT
- ORANGE :STARTER INTERRUPT O/P RELAY REQUIRED
- YELLOW / IGNITION INPUT (+)
- GREEN / (-) DOOR TRIGGER INPUT
- BLUE / (-) INSTANT TRIGGER INPUT ( HOOD, TRUNK)
- VIOLET / (+) DOOR TRIGGER INPUT
- BROWN/ WHITE / (-) HORN OUTPUT.
WIRING
Keep wiring away from moving engine parts, exhaust pipes and high-tension cable. Be sure to tape wires that pass
through holes on the rewall to prevent fraying.
CAUTION:
Do not connect the wire harness to the control module until all wiring to vehicle is complete.
2 PIN CONNECTOR (THE LED STATUS INDICATOR):
The led indicator status should be mounted in a highly visible area such as top of the dashboard, on top of the shifter
console or on the dashboard face. Leave at least 6mm space behind the mounting location for LED housing. Once a
suitable location is chosen, drill a 6mm hole. Run the LED wires through the hole then press the 2 pin LED housing into
place. Route the LED wires to the control module.
4
PROFESSIONAL SERIES
IM_FULL_SL2_REV_B
5 PIN WIRE HARNESS:
RED / WHITE WIRE –PARKING LIGHT RELAY INPUT —
The RED/WHITE wire is the input to the ashing parking light relay. The connection of the RED/WHITE wire will determine
the output polarity of the ashing parking light relay.
If the vehicle you are working on has +12volt switched parking lights, you don’t need connect this wire. This wire is
already connected to +12volt.
If the vehicle’s parking lights are ground switched, cut the RED/WHITE wire, connect the RED/WHITE wire to
chassis ground.
WHITE WIRE — PARKING LIGHT RELAY OUTPUT
(+12 V 10A OUTPUT) —
Connect the WHITE wire to the parking light wire coming from the headlight switch. Do not connect the WHITE wire to the
dashboard lighting dimmer switch. (Damage to the dimmer will result). The limitation of the WHITE wire is 10 AMP max.
Do not exceed this limit or damage to the alarm and parking relay will result.
BLACK WIRE — SYSTEM GROUND –
This is the main ground connection of the alarm module. Make this connection to a solid section of the vehicle frame. Do
not connect this wire to any existing ground wires supplied by the factory wire loom, make the connection to the vehicle’s
frame directly.
BROWN WIRE – (+) SIREN OUTPUT –
This wire is provides power to the supplied siren. Connect the Brown wire to the Red wire of the siren. Connect the Black
wire of the siren to a stable chassis ground.
RED WIRE — SYSTEM POWER (+12V CONSTANT) —
The RED wire supplies power to the system. Connect this wire to a stable constant +12 volt source.
2 PIN BLUE CONNECTOR FOR THE VALET SWITCH:
Select a mounting location for the switch that is easily accessible to the driver of the vehicle. The switch does not have to
be concealed, however, concealing the switch is always recommended, as this provides an even higher level of security to
the vehicle. Mount the valet switch in a hidden but accessible location. Route the valet switch wires to the control module.
7 - PIN ACCESSORY CONNECTOR
- GRAY WIRE / CHANNEL 3 NEGATIVE TRUNK OUTPUT
- ORANGE :STARTER INTERRUPT O/P RELAY REQUIRED
- YELLOW / IGNITION INPUT (+)
- GREEN / (-) DOOR TRIGGER INPUT
- BLUE / (-) INSTANT TRIGGER INPUT ( HOOD, TRUNK)
- VIOLET / (+) DOOR TRIGGER INPUT
- BROWN/ WHITE / (-) HORN OUTPUT.
5
PROFESSIONAL SERIES
IM_FULL_SL2_REV_B
Gray wire – (-) 200mA Channel 3 (Trunk) Output –
This will become a 1 second pulse ground by activate (button 3) on transmitter for two seconds, the current capacity of
this wire is 200 mA. This feature allows you to remote control trunk release or other electric device.
(A relay may be required).
Orange wire – (-) 200mA Grounded Output When Armed –
This wire will become grounded when the alarm is armed. The current capacity of this wire is 200mA. This output can
control starter disable, when an intrusion is detected and the system is triggered. This prevents any unauthorized starting
of the vehicle.
87
85
30
86
IN4003 Diode
Orange wire
from control module
“Start”
“On”
Purple wire
X
Cut
Yellow
wire
White wire
“Acc”
“Off”
Starter
VIOLET wire (Starter output)
form Heavy Gauge wire harness
Red wire to
Ignition Switch
Yellow wire - 12 volt with the ignition ON +
Connect this wire to a 12 Volt source when the ignition of the vehicle is in the ON position.
Green wire – Negative Door Switch Sensing Input (Zone 3) –
This wire is the ground trigger input wire for negative door pin switch. This wire is connection for “grounding” type factory
door pins locate the “common wire” that connects the door pin switches. Make the connection of the GREEN Wire here.
Blue wire – Ground Instant Trigger Input (Zone 2) –
This wire is the ground trigger input wire for hood and or trunk pin switches.
Violet wire – Positive Door Switch Sensing Input (Zone 3)–
This wire is the positive trigger input wire for positive door pin switch. This wire is connection for “positive” type factory
door pins(typical FORD MOTOR). Locate the “common wire” for all door pins and make the connection of the VIOLET
Wire here.
Brown / White wire wire – (-) 200mA Programmable Output Horn Output –
This wire is provided to use the existing vehicle’s horn
as the alarm system’s optional warning audible device.
It’s a transistorized low current output, and should only
be connected to the low current ground output from the
vehicle’s horn switch. When the system is triggered, the
horn will sound.
Factory Security Rearm Signal Output –(See Alarm Feature Programming) –
This output is programmable. If programmed rearm a factory installed security system. This wire will supply a pulse
whenever the remote start times out or is shut down using the transmitter and remote door locking.
85
86
87
87a
30
Brown/White
wire
To horn
+ 12 V
+12V Or Ground
Depending On System
Requirements
FUSE
6
PROFESSIONAL SERIES
IM_FULL_SL2_REV_B
3 PIN DOOR LOCK CONNECTOR: (Maximum 500mA Output)
Blue
Wire
Green
Wire
( - ) Lock Pulse
( + ) Unlock Pulse
( - ) Unlock Pulse
(+) Lock Pulse
Red(not used)
NEGATIVE TRIGGER DOOR LOCK SYSTEM
Red (not used)
Blue Wire Door Unlock
Green Wire Door Lock
Locking
Master
Switch
To Exiting
Door Lock Relay
+12V
Master Door
Lock Switch
X
X
Splice
Splice
Cut the Existing
Lock Wire
To Door
Lock
Motor
To Slave Door
Lock switches
Cut the Existing
Unlock Wire
3 Pin Plug
To Alarm
5-WIRE ALTERNATING DOOR LOCK
30
86
87a
85
87
30
86
87a
85
87
Red +12V
Green Wire
Blue Wire
POSITIVE TRIGGER DOOR LOCK SYSTEM
Blue Wire Door lock
Green Wire Door Unlock
Locking
Master
Switch
To Exiting
Door Lock Relay
+ 12V
Red (not used)
VACUUM OPERATED CENTRAL LOCKING
Green Wire
Blue Wire
+12V
X
Cut
Compressor
Door Switch
30
86
87a
85
87
30
86
87a
85
87
3 Pin
Plug To
Alarm
2 STEP DOOR UNLOCK WIRE CONNECTION FOR
5 WIRE ALTERNATING DOOR LOCKS
+12V
Cut the Existing
Lock Wire
Cut Existing Unlock
Wire
X
Cut the Unlock Wire
Lock
Unlock
OEM Door Master Lock
Switch
OEM Slave
Door Lock
Switch
+12V
Lock
Unlock
To All Other
Door Lock
Motors
H2/13:
22-Pin
Plug
From
Alarm
Pink Wire
x
X
Blue Wire
OEM Driver’s
Door Lock Motor
+ 12V
85
86
87
87a
30
30
87
85
87a
86
30
87
85
87a
86
Green Wire
H9:
3 Pin
Plug
To
Alarm
Red +12V
2 STEP DOOR UNLOCK WIRE CONNECTION FOR
GROUND SWITCHED DOOR LOCKS
Cut Existing Unlock
Wire
X
Lock
Unlock
OEM Door Master Lock Switch
To All Other
Door Lock
Motors
White/Green
Wire
OEM
Driver's
Door Lock
Motor
Existing Neg.
Lock Wire
Existing Neg.
Unlock Wire
86
30
85
87
87a
+ 12V
Green Wire
Door Lock
Blue Wire
Door Unlock
OEM Door
Lock Relay
H2/13:
22-Pin
Plug
From
Alarm
H9:
3 Pin
Plug
To
Alarm
2 STEP DOOR UNLOCK WIRE CONNECTION FOR
POSITIVE SWITCHED DOOR LOCKS
Cut Existing Unlock
Wire
X
Lock
Unlock
OEM Door Master Lock Switch
To All Other
Door Lock
Motors
White/Green
Wire
OEM Driver's
Door Lock
Motor
+ 12V
Existing Pos.
Lock Wire
Existing Pos.
Unlock Wire
30
87a
87
86
85
+12V
+ 12V
OEM Door
Lock Relay
86
30
85
87
87a
Green Wire
Door Unlock
Blue Wire Door Lock
H2/13:
22-Pin
Plug
From
Alarm
H9:
3 Pin
Plug
To
Alarm
VACUUM OPERATED DOOR LOCKING SYSTEM:
TYPICAL OF MERCEDES BENZ AND AUDI.
Locate the wire under the driver’s kick panel. Use the voltmeter
connecting to ground, verify that you have the correct wire with
the doors unlocked, the voltmeter will receive “12 volts”. Lock
the doors and the voltmeter will read “0 volt”. Move the alligator
clip to +12V and the voltmeter will receive “12 volts”. Cut this
wire and make connections. Be sure to program door lock timer
to 3.5 seconds. (See Alarm Feature B – 3 Programming.)
7
PROFESSIONAL SERIES
IM_FULL_SL2_REV_B
TRANSMITTER PROGRAMMING
Enter:
1. Turn the Ignition ‘switch ‘OFF/ON’ 3 TIMES and stay in ON position. Within 15 seconds.
2. Push the Valet switch 3 times and hold in on the 3rd push, when a long chirp is heard then release the valet switch.
You are now in the Transmitter programming mode.
Program:
1. Press any button on transmitter 1 until the siren responds with a conrming chirp; the rst transmitter is now
programmed.
2. Press any button on the second transmitter until the siren responds with a conrming chirp; the second transmitter is
now programmed.
3. Apply the same procedure to program 3rd and 4th transmitters.
FEATURE PROGRAMMING:
FEATURE “A” PROGRAMMING:
1. Turn the Ignition ‘switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
Push the Valet switch 3 times and hold in on the 3rd push. When a long chirp is heard, release the valet switch. You
are now in the Alarm feature ‘A’ programming mode.
2. Press the transmitter button corresponding to the feature you want to program.
The factory default settings is always [1] LED ash, [1] chirp.
3. Press the transmitter button again to change the feature. Simply keep pressing the transmitter button again until the
module advances to your desired setting.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulse
1
Chirps on Chirps off
2
Automatic Rearm OFF Automatic Rearm ON
3
45 sec. Delay Door Ajar error chirp. Instant Door Ajar error chirp
Exit: Turn Ignition to ‘ON’ position, or leave it for 15 seconds. 3 long chirps will conrm exit.
45 seconds Delay Door Ajar Error Chirp:
This feature controls the error chirp that is generated if the system is armed with the door trigger active. This is useful in
a vehicle that has a long dome light delay after the door has been closed. If the system is armed before the dome light
has turned off, the security system will generate the door trigger error chirp. Use this feature to disable the door open
error chirp.
8
PROFESSIONAL SERIES
IM_FULL_SL2_REV_B
FEATURE “B” PROGRAMMING:
1 Turn the Ignition ‘switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Valet switch 4 times and hold in on the 4th push. When a long chirp is heard, release the valet switch. You
are now in the Alarm feature “B” programming mode.
3 Press the transmitter button corresponding to the feature you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
1
0.9-second Door
lock pulses
3.0-second
Door lock
pulse
Double pulse
unlock
2
Active arming Passive arming
without passive
door locking
Passive arming
with passive
door locking.
3
Ignition
controlled door
locks & unlocks
Without ignition
controlled
door locks &
unlocks
4
Standard horn
timing
Horn chirp
Duration 30
mS
Horn chirp
Duration 10 mS
Exit: Turn Ignition to ‘ON’ position, or leave it for 15 seconds. 3 long chirps will conrm exit.
FEATURE “C” PROGRAMMING:
1 Turn the Ignition ‘switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2 Push the Valet switch 5 times and hold on the 5th push. When a long chirp is heard, release the valet switch. You are
now in the Alarm feature “C” programming mode.
3 Press the transmitter button corresponding to the feature you want to program.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulse
Three Chirps /
LED three pulse
1
Gray Wire =
Trunk (Channel
3) Output
Gray Wire =
Two Step Door
Unlock Output
Gray Wire =
Pager Output
2
Car Jacking
feature Off
Car Jacking
feature On
3
ALARM with
Keyless Entry
Keyless Entry
ONLY
Exit: Turn Ignition to ‘ON’ position, or leave it for 15 seconds. 3 long chirps will conrm exit
9
PROFESSIONAL SERIES
IM_FULL_SL2_REV_B
FEATURE “D” PROGRAMMING:
1. Turn the Ignition ‘switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
2. Push the Valet switch 6 times and hold on the 6th push until a long chirp is heard then release the valet switch. You are
now in the Alarm feature “D” programming mode.
3. Press and hold the transmitter button for two seconds to enter shock sensor program mode.
Press
Transmitter
Button
One Chirp /
LED one pulse
Factory Default Setting
Two Chirps /
LED two pulse
1
Shock Sensor Program
Mode
ADJUST AND TEST THE SENSITIVITY LEVEL
OF THE SHOCK SENSOR
Turn the Ignition switch ‘ON/OFF’ 3 TIMES and stay in OFF position.
Push the Valet switch 5 times holding in on the 5th push. (A long chirp will be heard.) Release the valet switch. You are
now in the feature ‘Shock Sensor’ programming mode.
Press and hold the button for 2 seconds. One long siren chirp will indicate the unit is ready to accept adjustments of the
shock sensor.
Press the
button on the transmitter once. This will decrease sensitivity level by one. Each time the button is pushed
and a decrease is made the siren/horn chirp will respond with [1] chirp. Two chirps indicate the minimum sensitivity. Warn
away & full trigger will be deleted when minimum sensitivity is selected. Shock sensor is OFF.
Press the button on the transmitter once. This will increase sensitivity level by one. Each time an increase is made the
siren/horn chirp will respond with [1] chirp. Two chirps indicate the maximum sensitivity. Hit the bumper or strong metal
part of the vehicle to test the threshold level of the sensor.
a). Activate the warn-away (rst stage the shock sensor), the siren will emit a short chirp.
b). Activate the full alarm (second stage the shock sensor), the siren will emit a long chirp.
When you are satised with the setting, press the
button to lock in the adjustment. One long siren chirp will indicate
the unit has locked in the adjustment.
Note: If 30 seconds of inactivity expires or you turn ON the ignition during of above steps, the unit will exit the program
mode. Three long chirps will conrm exit.
It is the purchaser’s responsibility to register this product for any future warranty service.
Warning: Some batteries may contain Perchlorate
What is Perchlorate? Perchlorate is both a naturally occurring and manmade contaminant increasingly found in groundwater, surface water and soil.
Most perchlorate manufactured in the U.S. is used as an ingredient in solid fuel for rockets and missiles. In addition, perchlorate-based chemicals
are also used in the construction of highway safety ares, reworks, pyrotechnics, explosives, common batteries, and automobile restraint systems.
Perchlorate contamination has been reported in at least 20 states. Perchlorate greatly impacts human health by interfering with iodide uptake into
the thyroid gland. In adults, the thyroid gland helps regulate the metabolism by releasing hormones, while in children; the thyroid helps in proper
development. Perchlorate is becoming a serious threat to human health and water resources. “Perchlorate Material – Special handling may apply.” For
more information, go to http://www.dtsc.ca.gov/hazardouswaste/perchlorate/
Magnadyne Corporation 1111 W. Victoria Street Compton CA 90220 (800) 340-3200
For Warranty information: Please visit our website at www.silencer.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9

Silencer Silencer SL-2 Installation guide

Silencer
Brand
Silencer
Model
Silencer SL-2
Category
Motor vehicle electronics
Type
Installation guide
This manual is also suitable for

Silencer SL-2 is a 2-Channel Security System with Keyless Entry that provides professional-grade protection for your vehicle. The system boasts a range of advanced features designed to enhance your vehicle's security and convenience. With its programmable options, you can customize the system to meet your specific needs. Here are some of the key features and possible use cases:

  • 2-Channel Security: The system provides two independent security channels, allowing you to monitor and protect different areas of your vehicle separately.

  • Keyless Entry: The integrated keyless entry system lets you lock and unlock your vehicle remotely, providing added convenience and security.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents