Pyle PLMRKT14BK Owner's manual

Brand: Pyle

Model: PLMRKT14BK

Category: Car media receivers

Type: Owner's manual

This manual is also suitable for

OWNER’S MANUAL

Mobile Audio System

• PLL Synthesizer Stereo Radio

• Automatic Memory Storing

• Preset Equalization

• USB Interface

• Auxiliary Input Function

• Remote Control

PLMR18

www.pyleaudio.com

PLMRKT33

Installation ........................................3

Take out screw before installation......3

DIN Front-Mount (Method A) .............3

Installing the unit ............................3

Removing the unit...........................4

DIN Rear-Mount (Method B) ..............5

Wiring Connection ...........................6

Operation ..........................................7

Location of keys.................................7

Switching on/off the unit....................8

Sound adjustment..............................8

Loudness ...........................................8

Display ...............................................8

Mute...................................................8

Equalization........................................8

Remote sensor...................................8

Reset function....................................8

Radio operation .................................8

Switching to radio mode ................8

Selecting the frequency band.........8

Selecting station .............................8

Automatic memory storing &

program scanning...........................8

Station storing ................................9

Scan................................................9

Mono/Stereo...................................9

Weather band selection..................9

USB play operation............................9

SD/MMC operation ..........................11

Specification...................................12

Trouble shooting ............................13

CONTENTS

Notes:

• Choose the mounting location where

the unit will not interfere with the

normal driving function of the driver.

• Before finally installing the unit,

connect the wiring temporarily and

make sure it is all connected up

properly and the unit and the system

work properly.

• Use only the parts included with the

unit to ensure proper installation.

The use of unauthorized parts can

cause malfunctions.

• Consult with your nearest dealer if

installation requires the drilling of holes

or other modifications of the vehicle.

• Install the unit where it does not get in

the driver’s way and cannot injure the

passenger if there is a sudden stop,

like an emergency stop.

• If installation angle exceeds 30º from

horizontal, the unit might not give its

optimum performance.

• Avoid installing the unit where it would

be subject to high temperature, such

as from direct sunlight, or from hot air,

from the heater, or where it would be

subject to dust, dirt or excessive

vibration.

DIN FRONT/REAR-MOUNT

This unit can be properly installed either

from “Front” (conventional DIN Front-

mount) or “Rear” (DIN Rear-mount

installation, utilizing threaded screw holes

at the sides of the unit chassis).

For details, refer to the following

illustrated installation methods.

30º

TAKE OUT SCREW BEFORE

INSTALLATION

Before install the unit, please remove the

two screws.

DIN FRONT-MOUNT (Method A)

Installation Opening

This unit can be installed in any dashboard

having an opening as show below:

Installing the unit

Be sure you test all connections first, and

then follow these steps to install the unit.

1. Make sure the ignition is turned off,

and then disconnect the cable from

the vehicle battery's negative (-)

terminal.

2. Disconnect the wire harness and the

antenna.

3. Press the release button on the front

panel and remove the control panel

(see the steps of “to detach front

panel”).

4. Lift the top of the outer trim ring then

pull it out to remove it.

5. The two supplied keys release tabs

inside the unit's sleeve so you can

remove it. Insert the keys as far as they

will go (with the notches facing up) into

the appropriate slots at the middle left

and right sides of the unit. Then slide

the sleeve off the back of the unit.

182 mm

53 mm

Take out screw before installation

INSTALLATION

6. Mount the sleeve by inserting the sleeve

into the opening of the dashboard and

bend open the tabs located around the

sleeve with a screwdriver. Not all tabs

will be able to make contact, so

examine which ones will be most

effective. Bending open the appropriate

tabs behind the dashboard to secure

the sleeve in place.

7. Reconnect the wire harness and the

antenna and be careful not to pinch

any wires or cables.

8. Slide the unit into the sleeve until it

locks into place.

9. To further secure the unit, use the

supplied metal strap to secure the back

of the unit in place. Use the supplied

hardware (Hex Nut (M5mm) and Spring

Washer) to attach one end of the strap

to the mounting bolt on the back of

the unit. If necessary, bend the metal

strap to fit your vehicle's mounting

area. Then use the supplied hardware

(Tapping Screw (5x25mm) and Plain

Washer) to attach the other end of

metal strap to a solid metal part of the

vehicle under the dashboard. This strap

also helps ensure proper electrical

grounding of the unit.

Front Panel

Outer Trim Ring

L Key

Sleeve

R Key

Sleeve

Dashboard

Screwdriver

Tabs

Note: to install the short threading terminal

of the mounting bolt to the back of the

unit and the other long threading terminal

to the dashboard.

10. Reconnect the cable to the vehicle

battery's negative (-) terminal. Then

replace the outer trim ring and install

the unit's front panel. (see the steps

of “to install the front panel”).

Removing the unit

1. Make sure the ignition is turned off,

then disconnect the cable from the

vehicle battery's negative (-) terminal.

2. Remove the metal strap attached the

back of the unit (if attached).

3. Press the release button to remove the

front panel.

4. Lift the top of the outer trim ring then

pull it out to remove it.

5. Insert both of the supplied keys into

the slots at the middle left and right

sides of the unit, then pull the unit out

of the dashboard.

Spring Washer

Tapping Screw

Plain Washer

Hex Nut

Metal Strap

Mounting Bolt

INSTALLATION

Dashboard or

Console

Side view showing

Screw Holes marked

T, N

Factory Radio

Mounting

Bracket

Screw

DIN REAR-MOUNT (Method B)

If your vehicle is a Nissan, Toyota, follow

these mounting instructions.

Use the screw holes marked T (Toyota),

N (Nissan) located on both sides of the

unit to fasten the unit to the factory radio

mounting brackets supplied with your

vehicle.

To fasten the unit to the factory radio

mounting brackets.

Align the screw holes on the bracket with

the screw holes on the unit, and then

tighten the screws (5x5mm) on each side.

Note: the outer trim ring, sleeve and the

metal strap are not used for method B

installation.

INSTALLATION

WIRING CONNECTION

FRONT Lch

SPEAKER

GREEN

GREEN/BLACK

MEMORY

BACK-UP (B+)

MAIN UNIT

IGNITION

SWITCH (ACC+)

POWER

ANTENNA

RED

GROUND (B–)

YELLOW

BLACK

BLUE

RCA CABLE

ANTENNA CONNECTOR

(GREY)

Rch RED

Lch WHITE

WHITE

WHITE/BLACK

REAR Lch

SPEAKER

VIOLET

VIOLET/BLACK

GREY

GREY/BLACK

FRONT Rch

SPEAKER

REAR Rch

SPEAKER

FUSE

OPERATION

LOCATION OF KEYS

1 2 3 4 5 6 7 8 9 10 11 12

13141516171920212223 182425

OPERATION

FM1 FM2 FM3 AM

• SWITHCHING ON/OFF THE UNIT

Switch on the unit by pressing any

button. When system is on, press

button (1) to turn off the unit.

• SOUND ADJUSTMENT

Press SEL button (3) shortly to select

the desired adjustment mode.

The adjustment mode will change in

the following order:

By rotating the audio knob (3) it is

possible to adjust the desired sound

quality.

• LOUDNESS

Press BND/LOU button (4) for

several seconds to reinforce the bass

output. Press it for several seconds

again to release this function.

• DISPLAY

Exhibit current frequency and

activated functions on the display (6).

• AUXILIARY INPUT

This unit can be connected to a

portable audio player through the AUX

IN jack (13).

• MUTE

Press to mute the sound, press it (8)

again to resume the sound.

• EQUALIZATION

Press EQ button (7) to turn on

equalization function and to select

desired audio mode. There are five

kinds of mode as below:

• REMOTE SENSOR

Point the remote cantrol handset to

the remote sensor IR (5). Press the

function keys on the handset to

control the system.

• RESET FUNCTION

RESET button (25) must be activated

with either a ball point pen or thin

metal object. The RESET button is to

be activated for the following

reasons:

- Initial installation of the unit when all

wiring is completed.

- All the function buttons do not

operate.

- Error symbol on the display.

Note: If press RESET button (25), the

unit can’t work yet, please use a cotton

swab soaked in isopropyl alcohol to

clean the socket on the back of the

front panel.

RADIO OPERATION

• SWITCHING TO RADIO MODE

Press MODE button (11) shortly to

select radio mode, the radio mode

appears in the display together with

the memory band and frequency.

• SELECTING THE FREQUENCY

BAND

At radio mode, press BND/LOU(ENT)

button (4) shortly to select the desired

band.

The reception band will change in the

following order:

• SELECTING STATION

Press

button (2) or button (24)

shortly to activate automatic seek

function. Press for several seconds

until “MANUAL” appears on the

display, the manual tuning mode is

selected. If both buttons have not

been pressed for several seconds,

they will return to seek tuning mode

and “AUTO” appears on the display.

• AUTOMATIC MEMORY STORING &

PROGRAM SCANNING

- Automatic Memory Storing

Press AS/PS button (10) for several

seconds, the radio searches from the

current frequency and checks the

signal strength until one cycle search

is finished. And then 6 strongest

stations are stored into the

corresponding preset number

button.

- Program Scanning

Press AS/PS button (10) shortly to

scan preset station. When the field

strength level is more than the

threshold level of stop level, the radio

is holding at that preset number for

several seconds with releasing mute,

then searches again.

VOL BAS TRE BAL FAD

(Volume) (Bass) (Treble) (Balance) (Fader)

FLAT CLASSICS POP M ROCK M DSP OFF

It supports the MP3/WMA file in the

device, the operation please refer to the

following instruction.

• SELECTING TRACKS IN SINGLE

STEP

Press

button (24) or button(2)

to move to the previous track or the

following track. Track number shows

on display.

• SELECTING TRACKS IN SINGLE

STEP

Press M5 button (16) or M6 button

(15) to select directory downward or

upward. If the MP3/WMA fold does

not contain any directory, there is no

function of pressing M5 button (16) or

M6 button (15).

• PAUSING PLAYING

Press

button (21) to pause CD

player. Press it again to resume play.

• PREVIEWING ALL TRACKS

Shortly press SCN button (20) to play

first several seconds of each track

stored in USB device. Shortly press

again to stop intro and listen to track.

Press and hold SCN button (20) to

intro the tracks stored in the current

directory. Press and hold it will exit the

intro.

• REPEATING THE SAME TRACK

Shortly press RPT button (19) to

continuously repeat the same track.

Shortly press it again to stop repeat.

Press and hold RPT button (19) will

repeat all the tracks stored in the

current directory. Press and hold it

again to stop repeat.

• PLAYING ALL TRACKS IN RANDOM

Shortly press SHF button (17) to play

all tracks stored in USB device in

random order. Shortly press it again

to cancel the function. Press and hold

SHF button (17) will play all tracks in

the current directory in the random

order, press and hold it again will exit

this mode.

• STATION STORING

Press any one of the preset button(18)

(1 to 6) to select a station, which had

been stored in the memory. Press this

button for several seconds (until 2ND

beeps come out), current station is

stored into the number button.

• SCAN

Press it to set the function to scan (23)

mode, which scanning to higher

frequency station with receivable signal

and keep on each station for several

seconds.

• MONO/STEREO

Press the button to set the reception

between mono (14) mode or stereo

mode.

USB PLAY OPERATION

In the front panel of the unit, there is

an USB interface (12). You can connect

an USB driver through this interface

(12).

For the unit with no SD/MMC interface,

when you connect an USB driver

through the interface, the unit will

search the MP3 files or WMA files in

the USB driver and start to play MP3

files or WMA files automatically. If in

other mode, you can also press MODE

button (11) to select USB mode.

OPERATION

name are displayed (selected). The user

can select the directory or file in the

directory by volume knob.The selected

file can be played by pressing

BND/LOU/ENT button.

• DISPLAY INFORMATION

Press DISP button (9) to show

following information, such as the

clock, ID3 TAG (if available: song title,

directory name, artist name, other

contents…) and other information.

Note:

• The main unit can only support the

standard USB-memory disc which is

approved by Microsoft.

• USB MP3 player is not a standard

which means different brand name or

different models have their own

standard. So our product cannot

support every MP3 player.

• When connecting an MP3 player and

there has normal battery in the player

(non rechargeable battery), you should

remove the battery from the MP3 player

then connect it to the USB interface.

Otherwise, it may cause battery burst.

• When in USB play mode, be sure not

to remove the USB driver from the USB

interface.

• SELECTING TRACKS BY

AS/PS/Navi-SCH BUTTON

AS/PS (Navi-SCH) button is assigned

as file searching button in MP3 file

operation.

When pressed, it is activated as

selecting each mode of Digital Audio.

“Searching track number” =>

“Navigation”from root by volume knob

=> “Navigation” from current directory

by volume knob.

Searching Track Directly

Press AS/PS (Navi-SCH) button for

one time. It enters into “Selecting

track number” mode.

You can use the volume knob (3) to

search the track number. Rotate the

knob clockwise or counter-clockwise

to increase or decrease the track

number in a sequence. The

corresponding track number, such as

“TRACK 12” will appear on the display.

You can also use the M6 (15) and M5

(16) buttons to fast select the track

number. Each time when you press M6

button (15) or M5 button (16), you can

increase or decrease ten track

numbers. Such as track 12 will skip to

track 22.

Searching Directory or File Name

Press AS/PS (Navi-SCH) button for

two times. The unit searches file or

directory from root by volume knob

(3). Display will list all available

directories and songs. Select the

desired directory/songs by using

volume knob and BND/LOU/ENT

button to confirm. If the selected title

is a song, it starts to play.

If the selected title is a directory name,

then use the volume knob to list all

songs under this directory and select

the title. Press BND/LOU/ENT button

to confirm and start to play. Repeat

the above steps if the newly selected

title is again a directory.

Searching From Current Directory

Press AS/PS (Navi-SCH) button for

three times. The unit searches file or

directory from current directory by the

volume knob. The current directory

name and the currently playing file

OPERATION

SUPPORTED MP3/WMA DECODING

MODES

The main unit supports MP3/WMA (Windows

Media Audio) decoding modes as below.

Supports

Mode

Stereo

Standard

MPEG1 Audio

Layer 3

(44.1kHz)

Windows

Media Audio

(44.1kHz)

Bit Rate (kbps)

32, 48, 64, 96,

128, 192, 256,

320

64, 96, 128,

192

The USB solution can support:

1. Folder: 500 max.

2. File: 999 max.

3. Depth of folder: 8 layers

4. Size: 1 GB

CAUTION:

When there are important files in the USB

device, do not connect it to the main unit

to play. And don’t play the CD-R/RW disc

that has important files in it. Because any

wrong operation may cause files loss.

And our company assumes no

responsibility for this.

SD/MMC OPERATION

There is a SD/MMC interface (22) on the

front panel of the unit.

When you insert a SD/MMC card in the

SD/MMC interface, the unit will search

the MP3 files or WMA files in the card and

start to play MP3 files or WMA files

automatically. The operation is the same

with the MP3 operation described above.

If in other mode, you can also press

MODE button (11) to select SD/MMC

mode.

When there is no USB driver in the USB

interface, you cannot record to SD/MMC

directly.

When there are important files in the

SD/MMC card, do not connect it to the

main unit to play.

GENERAL

Power Supply Requirements : DC 12 Volts, Negative Ground

Chassis Dimensions : 178 (W) x 160 (D) x 50 (H)

Tone Controls

- Bass (at 100 Hz) : ± 10 dB

- Treble (at 10 KHz) : ± 10 dB

Maximum Output Power : 4 x 40 Watts

Current Drain : 15 Ampere (max.)

CD PLAYER

Signal to Noise Ratio : More than 55 dB

Channel Separation : More than 45 dB

Frequency Response : 40 Hz - 18 KHz

RADIO

Frequency Coverage : 87.5 to 107.9 MHz

IF : 10.7 MHz

Sensitivity (S/N = 30 dB) : 4 μV

Stereo Separation : > 25 dB

Frequency Coverage : 530 to 1710 KHz

IF : 450 KHz

Sensitivity (S/N = 20 dB) : 36 dBu

SPECIFICATION

TROUBLE SHOOTING

Before going through the checklist, check wiring connection. If any of the problems

persist after checklist has been made, consult your nearest service dealer.

Symptom Cause Solution

No power. The car ignition switch is If the power supply is

not on. connected to the car accessory

circuits, but the engine is not

moving, switch the ignition key

to “ACC”.

The fuse is blown. Replace the fuse.

No sound. Volume is in minimum.

Adjust volume to a desired level.

Wiring is not properly Check wiring connection.

connected.

The operation keys The built-in microcomputer Press the RESET button.

do not work. is not operating properly Front panel is not properly fixed

due to noise. into its place.

The radio does not The antenna cable is not Insert the antenna cable firmly.

work. The radio connected.

station automatic

selection does not The signals are too weak. Select a station manually.

work.

8800-0C3023-02

Pyle PLMRKT14BK Owner's manual

Brand: Pyle

Model: PLMRKT14BK

Category: Car media receivers

Type: Owner's manual

This manual is also suitable for

Download PDF

report

Pyle PLMRKT14BK Owner's manual

This manual is also suitable for

Pyle PLMRKT14BK Owner's manual

Related papers

Other documents