Samsung SCC-C4353P User manual

User Manual

Power Zoom Camera

SCC-C4253

SCC-C4353

SCC-C4255

SCC-C4355

imagine the possibilities

Thanks you for purchasing this Samsung product.

To receive a more complete service, please visit

our website

www.samsungsecurity.com

NTSC ENGLISH.indd 1 2009-9-22 15:48:26

2_ overview

overview

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER

SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of

electric shock is present within this unit.

This symbol indicates that there are important operating and

maintenance instructions in the literature accompanying this unit.

WARNING

To reduce the risk of ﬁre or electric shock, do not expose this appliance to rain or

moisture.

To prevent injury, this apparatus must be securely attached to the ﬂoor/wall in

accordance with the installation instructions.

WARNING

Be sure to use only the standard adapter that is speciﬁed in the speciﬁcation sheet.

Using any other adapter could cause ﬁre, electrical shock, or damage to the

product.

Incorrectly connecting the power supply or replacing battery may cause explosion,

ﬁre, electric shock, or damage to the product.

Do not connect multiple cameras to a single adapter. Exceeding the capacity may

cause abnormal heat generation or ﬁre.

Securely plug the power cord into the power receptacle. Insecure connection may

cause ﬁre.

When installing the camera, fasten it securely and ﬁrmly. The fall of camera may

cause personal injury.

Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or

containers ﬁlled with water on top of the camera. Doing so may cause personal

injury due to ﬁre, electric shock, or falling objects.



1.

2.

3.

4.

5.

6.

NTSC ENGLISH.indd 2 2009-9-22 15:48:26

English _3

English

Do not install the unit in humid, dusty, or sooty locations. Doing so may cause ﬁre

or electric shock.

If any unusual smells or smoke come from the unit, stop using the product. In such

case, immediately disconnect the power source and contact the service center.

Continued use in such a condition may cause ﬁre or electric shock.

If this product fails to operate normally, contact the nearest service center. Never

disassemble or modify this product in any way. (SAMSUNG is not liable for

problems caused by unauthorized modiﬁcations or attempted repair.)

When cleaning, do not spray water directly onto parts of the product. Doing so may

cause ﬁre or electric shock.

CAUTION

Do not drop objects on the product or apply strong blows to it. Keep away from a

location subject to excessive vibration or magnetic interference.

Do not install in a location subject to high temperature (over 50°C), low temperature

(below -10°C), or high humidity. Doing so may cause ﬁre or electric shock.

If you want to relocate the already installed product, be sure to turn off the power

and then move or reinstall it.

Remove the power plug from the outlet when there is a lighting storm. Neglecting

to do so may cause ﬁre or damage to the product.

Keep out of direct sunlight and heat radiation sources. It may cause ﬁre.

Install it in a place with good ventilation.

Avoid aiming the camera directly towards extremely bright objects such as sun, as

this may damage the CCD image sensor.

Apparatus shall not be exposed to dripping or splashing and no objects ﬁlled with

liquids, such as vases, shall be placed on the apparatus.

The Mains plug is used as a disconnect device and shall stay readily operable at

any time.

When using the camera outdoors, moisture may occur inside the camera due

to temperature difference between indoors and outdoors. For this reason, it is

recommended to install the camera indoors. For outdoor use, use the camera with

built-in fan and heater.

7.

8.

9.

10.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

NTSC ENGLISH.indd 3 2009-9-22 15:48:26

overview

4_ overview

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following

two conditions :

1) This device may not cause harmful interference, and

2) This device must accept any interference received including interference that may

cause undesired operation.

Caution

This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated

in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to

correct the interference at his own expense.

IC Compliance Notice

This Class A digital apparatus meets all requirements of the Canadian

Interference.-Causing Equipment Regulations of ICES-003.

NTSC ENGLISH.indd 4 2009-9-22 15:48:26

English _5

English

IMPORTANT SAFETY INSTRUCTIONS

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in accordance with the manufacturer’s

instructions.

Do not install near any heat sources such as radiators, heat registers, or other

apparatus (including ampliﬁers) that produce heat.

Do not defeat the safety purpose of the polarized or grounding-type plug.

A polarized plug has two blades with one wider than the other. A grounding type

plug has two blades and a third grounding prong. The wide blade or the third prong

is provided for your safety. If the provided plug does not ﬁt into your outlet, consult

an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs,

convenience receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories speciﬁed by the manufacturer.

Use only with the cart, stand, tripod, bracket, or table speciﬁed

by the manufacturer, or sold with the apparatus. When a

cart is used, use caution when moving the cart/apparatus

combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms or when unused

for long periods of time.

Refer all servicing to qualiﬁed service personnel. Servicing is required when the

apparatus has been damaged in any way, such as powersupply cord or plug is

damaged, liquid has been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not operate normally, or has

been dropped.

Apparatus shall not be exposed to dripping or splashing and no objects

filled with liquids, such as vases, shall be placed on the apparatus

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

14.

NTSC ENGLISH.indd 5 2009-9-22 15:48:27

overview

6_ overview

CONTENTS

OVERVIEW

2

5 Important Safety Instructions

6 Contents

7 Features

8 What’s Included

8 At a Glance

INSTALLATION &

CONNECTION

12

12 Preparing Installation

12 Connecting the Cables

SETUP

15

15 Main Menu

16 Proﬁle

18 Camera Set

27 Intelligent Video

29 Privacy Zone

30 Preset

31 Other Set

32 Communication

32 System Info

33 Language

APPENDIX

35

35 Shortcut Keys

36 Speciﬁcations

NTSC ENGLISH.indd 6 2009-9-22 15:48:27

English _7

English

FEATURES

With the state-of-the-art digital signal processing technology, full digital image

processing and special algorithm of 600-line high resolution implemented.

High Sensitivity: It implements images of high sensitivity using the up-to-date

Super-HAD IT CCD(SCC-C4253/C4353)/ExView-HAD PS CCD(SCC-C4255/

C4355).

VPS(Virtual Progressive Scan): This is an advanced technology that reproduces

a sharp progressive image. This is appropriate to high quality recording and ﬁle

transfer via the Internet. (SCC-C4255/C4355 only)

High performance surveillance camera, equipped with x43 zoom lens and digital

zoom IC, enabling monitoring up to 688 times

WDR extends the contrast range as it takes a picture of each of dark and bright areas

before compositing the two, which is useful if you take a picture of windows inside

a building. Namely, it improves the picture quality of the outdoor scenery as well as

indoor.(SCC-C4255/C4355 only)

Low Illumination: It uses the digital signal technologies such as low illumination and

Day/Night functions that make your camera identify objects even in the worst envi-

ronment.

XDR (eXtended Dynamic Range): Actively controls the gamma compensation in the

way it operates the ambient luminance contrast in a certain pixel unit to determine

the optimal visibility.

Digital Power Synchronization: The full digital Line Lock function directly adjusts the

vertical camera synchronization to enhance the operationability and reliability of this

camera.(SCC-C4353/C4355 only)

DAY/NIGHT:

This function can make the IR Cut ﬁltering function inactive under the illumina-

tion below the normal value.

White Balance to control the brightness to the illumination

Superior Backlight Adjustment:When an object has a bright illumination or sunlight

behind it, this camera automatically improves the shaded object picture quality.

Auto Focus to automatically adjust the focus to the subject movement

Privacy zone to hide a speciﬁc area for personal privacy.



NTSC ENGLISH.indd 7 2009-9-22 15:48:27

overview

8_ overview

AT A GLANCE

SIDE VIEW

Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you

have applied ethanol.

M



WHAT’S INCLUDED

Please check if your camera and accessories are all included in the product package.

Camera

Camera Holder

(Mount Adaptor)

2 Screws

User's Manual

Mount Adapter

Fixing Grooves

Camera Lens

NTSC ENGLISH.indd 8 2009-9-22 15:48:28

English _9

English

Rear Panel

 









 









[Z\\

[Z\Z

SCC-C4353

 









 









[Y\\

[Y\Z

SCC-C4253

 Input/Output Connector

This connector has input and output ports for RS-485 control signals,

DAY/NIGHT switching, and alarm output signals.

[Y\\V[Z\\

[Y\ZV[Z\Z

SCC-C4355

 









 









[Z\\

[Z\Z

 









 









[Y\\

[Y\Z

SCC-C4255

[Y\\V[Z\\

[Y\ZV[Z\Z

SCC-C4255/C4355

SCC-C4253/C4353

NTSC ENGLISH.indd 9 2009-9-22 15:48:30

overview

10_ overview

1. ALARM OUT

Alarm out jack for motion detection. (Open Collector, On Gnd)

2. GND

Grounding jack.

3. TRIGGER IN (SCC-C4255/C4355)

Displays the current still image when it receives the Trigger signal. (Normal

Open Type)

4.5.6 FOCUS, COM, ZOOM

This port is used for ZOOM/FOCUS, MENU CONTROL, HOME

RETURN, and ONEAF by using an external controller.

Depending on the input condition, 4 modes, A, B, C, and D are

available. (SPECIAL - CTRL TYPE)

(Operation Voltage Range : +3V~+13V, -3V~-13V)

1) When the voltage is supplied to either ZOOM or FOCUS port

Function

*1

Code

Tele(Up)

Wide(Down)

Near(Left) Far(Right)

ZOOM Port FOCUS Port

A -6V +6V -6V +6V

B -6V +6V +6V -6V

C +6V -6V -6V +6V

D

+6V -6V +6V -6V

*1: During MENU OFF, controls ZOOM/FOCUS and during MENU ON,

changes the direction, Up/Down/Left/Right SETUP switch.

2) When the voltage is supplied to both ports

Function

Code

ENTER/AF *2 HOME RETURN *3

ZOOM Port

FOCUS Port

ZOOM Port

FOCUS Port

A -6V -6V +6V +6V

B -6V +6V +6V -6V

C +6V -6V -6V +6V

D

+6V +6V -6V -6V

NTSC ENGLISH.indd 10 2009-9-22 15:48:30

English _11

English

* 2 : For short voltage supply during MENU OFF, executes ONEAF and for

more than 2 second

* 3 : For more than 2 second long voltage supply, moves to the PRESET

0(HOME) position.

7. 5V OUT

Power supply jack for RS-485 JIG. Use within typical DC +5V 100mA.

8. DAY/NIGHT IN

This is a function to receive the external DAY/NIGHT signal from the

sensor(option) and convert the signal into BW.

9. RS-485 DATA-

Jack for connection to RS-485 DATA- signal line.

10. RS-485 DATA+

Jack for connection to RS-485 DATA+ signal line.

 SETUP Switch

This switch is used to set the function or property. When this switch is pressed

for at least 2 seconds, the MAIN MENU appears.



(Left/Right)

: By pressing this switch left or right, you can move left or right

on the menu or change the displayed value.



(Up/Down) :

By pressing this switch up or down, you can move up or down on

the menu.

 : When you press this switch in the menu, the selected function is conﬁrmed.

To enter a submenu, press this button.

 Video OUT Port

This is connected to the Video Input Port of the monitor and it outputs the

Video signals.

 GND

This is a grounding port.

 Power Connection Port

This is connected to the Power cable.

 Power Display LED

When the power is normally connected, the red LED lights.

NTSC ENGLISH.indd 11 2009-9-22 15:48:30

12_ installation & connection

installation & connection

PREPARING INSTALLATION

To install and use the camera, rst prepare the following cables.



Power Adapter Cable (sold separately)

The requirements for the power adapter, which connects to the camera’s

POWER IN terminal, are as follows:

- SCC-C4253/C4255 : DC 12V 600mA

- SCC-C4353/C4355: AC 24V 300mA

DC 12V 600mA



Video Cable(sold separately)

Use a BNC cable, such as the one shown below, to connect the camera’s VIDEO

OUT to the monitor.

CONNECTING THE CABLES

1. Connect one end of the BNC cable(not included) to the VIDEO OUT.

2. Connect the other end of the BNC cable (not included) to the VIDEO IN of the

monitor.



NTSC ENGLISH.indd 12 2009-9-22 15:48:31

English _13

English

3. Plug in the power adapter(not inlcluded). Use a “minus” screwdriver to connect one

part of the power adapter, which consists of two lines, to the POWER terminal of the

camera as follows :

1 2 3 4 5 6 7 8

1. ALARAM OUT

2. GND

3. TRIGGER IN

4.

FOCUS

5.

COM

6.

ZOOM

7. 5V OUT

8. DAY/NIGHT IN

+12V

GND

SCC-C4353(P)/C4355(P)

SCC-C4253(P)/C4255(P)

Video In Terminal of Monitor Rear Surface

BNC cable(not included)

Video Out Terminal

NTSC ENGLISH.indd 13 2009-9-22 15:48:31

installation & connection

14_ installation & connection

4. Determine the type of power supply and set the POWER SELECTION switch

accordingly. Next, plug the power adapter into a wall outlet.

5. If the camera operates normally, the following screen will be displayed for

5 seconds and then disappears.

6. The requirements for RS485 control is as follows :

- Signaling Speed: 9600 bps

- Data Bit : 8 bits

- Stop Bit : 1 bit

- Parity Bit : none

TYPE 4_ZOM_WDR_N

PROTOCOL SAMSUNG

ADDRESS 0

COMM.TYPE RS485,HALF

BAUD RATE 9600

CAMERA VER. V1.00_090817

LENS OK

NTSC ENGLISH.indd 14 2009-9-22 15:48:31

English _15

English

setup

Using OSD icons

_+

:

If these icons appear in the left and right corner of a menu item, you can use

them move to the previous or next menu.

(EXIT): Exits the menu setup screen.

Before exiting the setup screen, select <SAVE> to save your settings

to the whole menus, or <QUIT> to cancel them.

(RET): Saves your settings and returns to the previous screen.

(HOME): Returns to the main menu.

(SAVE): Use this icon if you want to save your settings after you speciﬁed the

mask area and privacy area, etc.

Once you saved your settings, the changes remain intact even if you

select <QUIT> on exit.

(DEL): Use this icon if you want to delete a mask, or privacy area, etc.

Once you deleted your settings, the deletions remain valid even if you

select <QUIT> on exit.

: This icon appears in the right of a menu containing sub menu items.

MAIN MENU

This is the ﬁrst screen you ever see when you turn on the camera where you can set the

camera environment to your needs.

PROFILE

Select a mode appr--opriate to the camera

installation environment.

CAMERA SET

You can configure the camera settings.

INTELLIGENCE

Offers motion detection and tracking functions.

PRIVACY ZONE

You can configure the privacy settings.

PRESET

You can set the PRESET POSITION.

OTHER SET

You can reset the camera, or adjust the OSD color to your preference.



PROFILE

NTSC ENGLISH.indd 15 2009-9-22 15:48:32

16_ setup

setup

COMMUNICATION

Conﬁgures the settings pertaining to RS-485 communication.

SYSTEM INFO

Shows the system information such as the camera version or communication

settings.

LANGUAGE

Select a preferred one from the supported languages.

PROFILE

You can select one from the pre-determined configurations as appropriate to your

specific camera installation environment.

Your selection on each item in PROFILE will affect all other settings of the camera.

STANDARD

Automatically optimizes the camera settings

to the normal environment.

ITS

This setting enables you to analyze the trafﬁc

situation and take the trafﬁc information at a

glance.

BACKLIGHT

This setting enables you to view a sharp

background and object even in a severe

backlight scene.

DAY/NIGHT

Automatically optimizes the camera settings to the day and night scene.

GAMING

This automatically configures the settings so that you can work in a stable illumina-

tion condition as indoors.

CUSTOM

Your change to any of the PROFILE settings will switch the display to CUSTOM.





PROFILE





STANDARD

ITS

BACKLIGHT

DAY/NIGHT

GAMING

CUSTOM

NTSC ENGLISH.indd 16 2009-9-22 15:48:32

English _17

English

CAMERA SETUP MENU

STANDARD ITS BACKLIGHT DAY/NIGHT GAMING

Parent Menu

Sub-menus

VPS

OFF ON OFF OFF OFF

IRIS

ALC ALC ALC ALC ALC

ALC - - - - -

LEVEL

0 0 0 0 0

BACKLIGHT

OFF OFF WDR OFF OFF

WDR - - - - -

WEIGHT Custom Setting Custom Setting MEDIUM Custom Setting Custom Setting

WDR LEVEL

Custom Setting Custom Setting 0 Custom Setting Custom Setting

WHITE BAL

Custom Setting Custom Setting Custom Setting Custom Setting Custom Setting

MOTION

(F.FAST)

---

(F.FAST)

---

NORM

(F.FAST)

---

SLOW

DNR

MEDIUM MEDIUM MEDIUM MEDIUM MEDIUM

SHUTTER

OFF OFF OFF OFF OFF

SENSE UP

AUTO X4 AUTO X2 AUTO X4 AUTO X4 AUTO X4

XDR

MEDIUM MEDIUM MEDIUM MEDIUM MEDIUM

DAY/NIGHT

AUTO AUTO DAY AUTO DAY

NIGHT - - - - -

BURST

OFF

ON

OFF OFF OFF

EXT

- - - - -

BURST

- - - - -

WHITE BAL

DAY DAY/NIGHT DAY DAY/NIGHT DAY

DAY

- - - - -

MODE

ATW2 ATW1 ATW1 ATW1 ATW1

RED

0 0 0 0 0

BLUE

0 0 0 0 0

NIGHT

- - - - -

BRIGHTNESS

- MEDIUM - MEDIUM -

MODE

OFF

ATW2

OFF

ATW2

OFF

RED -

0

-

0

-

BLUE

-

0

-

0

-

DETAIL

2 2 2 2 2

NTSC ENGLISH.indd 17 2009-9-22 15:48:32

18_ setup

setup

CAMERA SET

You can configure the general settings of the camera module.

Select <MAIN MENU> - <CAMERA SET>.

The Camera Setup menu appears.

Change the settings as necessary, or select

an item to check.

CAMERA ID

Provide the ID and location for a camera that displays on the screen.

Select <CAMERA SET> - <CAMERA ID>.

Use

▲▼

_+

to select a desired character,

then press [ENTER].

In the lower input box of the screen, the

selected character will be entered.

You can enter up to 54 characters including

alphabets, numbers and special characters.

LOCATION : Specify the display position

of the camera ID.

When done, press [ENTER].

The camera ID will be displayed in the speciﬁed position.

VPS

If you set it to <ON>, the camera images will be displayed in progressive mode.

VPS is only available for SCC-C4255 and SCC-C4355.

1.

2.

1.

2.





3.

M





CAMERA SET



CAMERA ID OFF

VPS OFF

IRIS ALC

MOTION (F.FAST)

---

DNR MID

SHUTTER (OFF)

---

SENS-UP AUTO X4

FLICKERLESS OFF

XDR MID

ABCDEFGHIJKLMNOPQRSTUVWXYZO

123456789

: ?

_

+



()/

-

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

NTSC ENGLISH.indd 18 2009-9-22 15:48:32

English _19

English

IRIS

The IRIS menu is useful if you set to adjust the

intensity of radiation incoming to the camera.

ALC : Adjust the open and close of the iris.

- LEVEL : Select an overall brightness level.

- BLC : With <BACKLIGHT

> set to

<BLC>, you can specify the BLC area.

With AREA set to <USER>, you can

specify the position and size.

- WDR : If you set <BACKLIGHT> to

<WDR>, you will see a menu where you

can set the WDR options.

Specify the shutter speed in WDR LEVEL,

and, the composition level in <WEIGHT>.

Select OUTDOOR, or INDOOR in

<WHITE BAL>.

The WDR feature provides an extension of

the gain range, which is useful, especially

if you work on pictures both indoors and

outdoors from inside of a building.

Namely, it improves the sharpness of the picture in outdoor scenery as well as

indoor.

As long as you use the VPS function, the WDR will not be available as the CCD read

method differs accordingly. If you set VPS to ON, WDR will be set to <OFF>

accordingly.

WDR is only available for SCC-C4255 and

SCC-C4355.

MANUAL : Adjust the iris level manually.

The overall brightness target of a camera

will be set to ALC level 0, while the iris

can be adjusted manually.



M





M



LEVEL

[

00

]

----

I

----

BACKLIGHT BLC

AREA USER

<SIZE>

LEVEL

[

00

]

----

I

----

BACKLIGHT WDR

WEIGHT MID

WDR LEVEL

[

0

]

----

I

----

WHITE BAL INDOOR

LEVEL

[

00

]

----

I

----

NTSC ENGLISH.indd 19 2009-9-22 15:48:33

20_ setup

setup

AGC

With this, you can adjust the AGC level of a

camera.

With AGC active, if the signal strength falls

below the standard level, AGC will amplify the

video signal to automatically improve the

sensitivity.

If <SENS-UP> is set to <OFF> or <FIX>

mode, the <MOTION> menu will switch to

<AGC>.

With the USER

( )

submenu selected, press

[ENTER] to display the corresponding screen.

In this mode, you can select from VERY LOW

to VERY HIGH in 16 levels, enabling deeper, wider choices to your convenience.

With the FIX

( )

submenu selected, press [ENTER] to display the corresponding

screen. In this mode, you can select an individualized mode in 16 levels, regardless of

the brightness.

As long as the DAY/NIGHT menu is set to AUTO in Camera Setup, the AGC menu is

not available.

As long as FLICKERLESS is set to ON, the AGC mode is not available.

If you set BACKLIGHT to WDR, the AGC ﬁx mode is not available.

MOTION

You can specify a level of AGC for controlling the camera motion.

This is available only of the SENSE UP menu is set to AUTO.

Select F.FAST if you want to monitor a very fast moving object in a low contrast

scene, and S.SLOW if monitoring a very slow moving, inanimate object in the same

condition.

As long as DAY/NIGHT is set to <AUTO>, the <MOTION> menu is not available.

DNR

Reduces the noise on the camera image.

The higher the level is, the greater the effect is.

Set it to <USER> to specify the level.

M





CAMERA SET



CAMERA ID OFF

VPS OFF

IRIS ALC

AGC (VERY HIGH)

---

DNR MID

SHUTTER OFF

SENS-UP OFF

FLICKERLESS OFF

XDR MID

NTSC ENGLISH.indd 20 2009-9-22 15:48:33

Page is loading ...

Samsung SCC-C4353P User manual

This manual is also suitable for

Samsung SCC-C4353P User manual

in other languages

Related papers

Other documents